Linksys Wireless Router :: E4200 V1 QOS Can Add Downlink Bandwidth?
Jun 8, 2012E4200 V1 QOS can add downlink bandwidth？
View 3 Replies
ADVERTISEMENT
Linksys Wireless Router :: E4200 Downlink Speed Limited To 6 Mbps
Dec 30, 2011I posted this in the wired forum, because it's the wired speed that is limited, but it looks like there's more E4200 expertise over here, so here it is again:
I have Hotwire fiber service and the plan is supposed to provide 20 megabit downlink speeds.
I just bought a Linksys/Cisco E4200 to replace an old Dell TrueMobile 2300 from 2004. With that router I got the full advertised downlink speed.
Now, when I run a speed test with the E4200 in place, the downlink speed is only 5168 kbps or so. Watching the speed test meters, I see the data arriving in bursts, every few seconds a whole lot of it gets through, then for a second or two nothing. It's pretty regular.
But, if I run a speed test with the ONT cable plugged right into a laptop, I see 19001 kbps - close enough to 20. This is the same cable that plugs into the back of the router.
With E4200 in place Direct into laptop what I can check or configure in the E4200 to change this behavior?
Linksys Wireless Router :: Add A Bandwidth Meter For E4200?
Mar 3, 2011I would love to see this added in a future firmware release. I imagine others would welcome it as well that have caps with their isp.
View 9 Replies View RelatedLinksys Wireless Router :: E4200 Cuts Bandwidth By Nearly Half
Dec 16, 2011I just signed up for Charter's Ultra 100Mbps internet service. We confirmed it worked at that speed by connecting my Lenovo T520 laptop directly to the Motorola Cable modem. I acheived just over 102Mbps throughput down.Next, I plugged in the e4200 (v1) router to the modem, and the computer directly to that (wired), and the max performance I could see was right around 52Mbps. Wireless performance on wireless-n, 5Ghz, maxes out at around 42Mbps.I am concerned about the throughput dropping from 102Mbps to 52Mbps while directly WIRED to the router. That tells me that the router is definitely capping my throughput. I have turned off QOS, found the optimum MTU of 1468 (used the ping -f -l 1440 [url]...) to find the largest MTU that didn't spit out a fragmented message, and added 28 to that.
I am a bit baffled that this top of the line router which some have claimed to see >100Mbps performance over wireless alone, isn't able to achieve any higher than 52Mbps wired. I do have other devices plugged in, but none actively transferring. What could be capping the throughput? The router worked fine on 25Mbps service, but it seems unable to handle 100Mbps service.
Linksys Wireless Router :: E4200 V2 - Limit Bandwidth On Particular Device?
Jul 6, 2012I want to know how I can manually limit the Kbps for a particular devince in the QOS.I DO NOT want to simply set the priority (low/med/high). I want to "physically" limit a device.
When I select to do it manually (upstream bandwidth) it limits ALL devices and I do not want this. I want to limit the bandwidth on only one device that is connected (ie an Xbox)
I have a Linksys E4200 V2
Linksys Wireless Router :: E4200 Not Allowing Full Internet Bandwidth
Oct 16, 2011I have a 100mb conection and regularly get 90mb plus speed when conected direct to the modem. If I conect via the E4200 I only get 50mb ? I have tried disabling the firewall and QOS but this has had no effect. I am using a wired conection and the latest firmware. Its almost as the E4200 is capped at 50mb throughput.
View 6 Replies View RelatedLinksys Wireless Router :: E4200 V1 Cannot Seem To Find Work Around For Wifi Bandwidth
May 2, 2012I recently bought myself the E4200v1 router, and have had several issues with it. One issue I cannot seem to find a workaround for is the wifi bandwidth problem.I have a 100/10 mbitl internet connection. The router claims to support 300/450 mbit speeds over wifi, so that should be plenty. in reality however, that isnt so.Even though my N-standard wifi adapter on my machine states it has a 130 mbit connection to the router, I consistently test the internet throughput when using wifi and speedtest.net to around 20-21 mbit. If I put in a cable, I instantly get full speed, 100/10 mbit.
Have to add; I am not new to the networking game, I have a CCNA and a degree in computer sciences, and work with hosting web sites using cloud tech every day. At this point, I have tried everything related to settings on the router, so I can only conclude that there's some kind of bug in the firmware. I would expect the standard firmware to work, and not having to install DDWRT or other custom firmware.
Linksys Wireless Router :: WRT120N Cuts Bandwidth
Mar 1, 2012Telefonica router (this my internet provider) --> WRT12N --wireless/eth--> my laptop
With that configuration I get a 1Mbps band with But in this configuration Telefonica router (this my internet provider) -- wireless/eth--> my lapto I get 7Mbps.Using always the same port of my telefonica router.Why the WRT120N is not providing the whole bandwidth? Is there any option in the router that divide the whole bandwith (7Mbps, almost 8Mbps) among the four ports of the wrt120n (giving 1Mbps per port)
Linksys Wireless Router :: WRT120N - How To Prioritize Computer's Bandwidth
Apr 20, 2013I have a Desktop wired to my WRT120N. With this router being a wirless one, we have other devices (2 laptop and 2 iPads) conected to the internet via WiFi.The thing is, whenever I play an online game (specifically, League of Legends) my ping skyrockets whenever they use the internet.Is there a way for my PC to take priority in bandwidth over theirs? Or at least some way for my game to take priority over theirs?
View 4 Replies View RelatedLinksys Wireless Router :: E1200 Cuts PPTP Bandwidth?
Oct 5, 2012I've got a problem with my new Linksys E1200 (v1) router. It cuts the bandwidth of my PPTP connection with ISP (which is 50 Mbps) down to about 12 Mpbs. My firmware is the latest one (v1.0.03 build 4). I've done some reading and found out that it's pretty common problem between Linksys E-Series routers and ISPs that use PPTP/L2TP.
View 4 Replies View RelatedLinksys Wireless Router :: E4500 Configure Settings Regarding 5 Ghz Bandwidth
Feb 14, 2013I just bought a Linksys E4500. I would like some support to configure the settings regarding the 5 Ghz Bandwidth.I need to fill out the cells for Server Radius IP and port.Which are the best setting for this section?
View 3 Replies View RelatedLinksys Wireless Router :: EA6500 Bandwidth Crush When Streaming?
Jan 7, 2013Been noticing this lately, thought a few times it was just random internet drops outs, but completely crushing bandwidth when streaming is normal for this router.
Its completely obvious when playing a game on xbox live or playing wow or diablo 3 on the pc, when streaming from youtube in 720p or higher the bandwidth is completely crushed. I downloaded a game yesterday also through games for windows marketplace on the pc yesterday and my brother couldn't play diablo 3 while I was downloading. I tried media prioritization and that doesn't fix the problem.
Interestingly enough I still own an E4200 so I hooked that router back up just to see how that handled things. I set my extension on chrome to always play youtube videos at 1080p if availible, and there was no lag or bandwidth crush. I logged onto xbox live while my brother was playing diablo 3 and downloaded a video trailer of a game and no bandwidth crush. Hmm I thought.... So I tried the EA6500 again and the bandwidth crush comes back and my brother can no longer play online games while Im streaming.
At this point Im just gonna suck it up and start using the E4200 again until EA6500 gets a good software update and can perform standard tasks. I have a 20mb download and a 2mb upload should this be happening with a router this expensive?
Linksys Wireless Router :: How To Use Full Wifi Bandwidth Of E1200
Oct 31, 2012I just bought a E1200 routerand using automatic setup by using CISCO connectafter that, I only got a CONNECT SPEED with about 10Mbps in my android smart phone,I would like to know how can I increase the WIFI strength WITHIN THE WIFI SETTING, I chose MIXED mode rather than specific in b/g/n mode.
View 4 Replies View RelatedLinksys Wireless Router :: EA4500 And Bandwidth Monitoring With Report
Dec 24, 2012I have a ea4500 router with 3 pc's, 4 iphones, 2 playstations, ipad, ps vita, house cat, and a printer all wired into the internet. There are four of us in the family all using the internet but I suspect one of us is using considerably more than the other. I live in the country and my current isp has us on the max available account - 50 gigs / month. Lately we have been hitting 45 in less than 3 weeks into the month. I would like to know which of the things connected or which person is using the most of the bandwidth up. Is there a program that doesn't require a phd in quantum physics and networking that can monitor this for me and spit out a report.
View 9 Replies View RelatedLinksys Wireless Router :: E3000 And 2 Xboxes Very Low Bandwidth Speeds
Jul 9, 2011I have 2 xbox 360's I'm trying to connect to my E3000 wirelessly. I've tried several different things, but I always end up with moderate/strict NAT on one or both xboxes. I tried going back to default settings, and got open NAT for both xboxes and very low bandwidth speeds for both, which caused a lot of online playing issues.I never had an issue with the bandwidth speed before until I reset to factory defaults.What is the best way to connect 2 xboxes at the same time without NAT and bandwidth issues?
View 4 Replies View RelatedLinksys Wireless Router :: E2500 Guest Network Bandwidth Throttle?
Dec 30, 2012I currently use a E2500 router for my home network. I have setup the Wireless guest Network for my downstairs Tenant while he is out of work so he can still have some internet. The problem however is that often the guest network will take up 90% of my 55mb/sec bandwidth, leaving none for the primary network. Is there a way for me to Throttle the amount of bandwidth the Guest network can use? Say alot 10mb/sec for Guest access only, and leave the rest for our main network?
View 6 Replies View RelatedLinksys Wireless Router :: WRV200 - Restrict Bandwidth / Internet Speed?
Jun 17, 2012I have a Linksys WRV200 and I wanted to know how can I restrict the internet speed for each computer on my network. Example: if my connection is 2 Mbps, One computer should have 1 Mpbs guaranteed, and the rest should split the rest.
View 1 Replies View RelatedLinksys Wireless Router :: E900 - Menu To Change Channel And Bandwidth
Jan 12, 2013I just purchased a Linksys Cisco E900 router and hooked it up to my Internet cable. The Internet service that my ISP is giving me is PPPoE, fiber link (100 Mbps).
I did the set up. I connected my computer (via Ethernet cable) and my laptop (via wireless) to the router.
Now... there are other wireless networks around me. The WI-Fi channel my router fixed to is 1, apparently - saw it from the settings. But I can't find a menu anywhere in the router's gateway (192.168.1.1) from where I can change the wireless channel, wireless bandwidth etc.
Linksys Wireless Router :: E2000 / Limit Bandwidth Speed Of Guest Accounts?
Jul 7, 2011How can I limit bandwidth speed of guest accounts? Or are there free softwares available to do something like that? It's kinda like the hotspot softwares - where we can set hourly, daily, monthly allowances and see a report on their connectivity.
View 3 Replies View RelatedLinksys Wireless Router :: Managing Bandwidth / Users On Home Network With E2000
Aug 13, 2012I've got the E2000 at home for our private network.
We are three guys sharing a flat. We have personal laptops, work laptops, mobile phones, games consoles, tablets etc that connect to the internet.
Problem is that when someone downloads stuff, the speed is slow for the rest of us. So i was hoping i could set up something like three "channels" so each of us could have the same download speed, ie 1 mbs each regardless if others are using the network at the same time. And then maybe a guest network for all the mobiles and tablets etc. MAC filtering for access for our personal laptops should work.
We have a 20mbit cable network line.
Can i do all of this on the E2000 and how?
Linksys Wireless Router :: WRT54GL Option To Restrict / Share Bandwidth Equally To Each Ethernet Port
Sep 5, 2011WRT54GL has an option to restrict or share the bandwidth equally to each ethernet port or wireless? I need this option in a low bandwith area because the first computer connected to the router who makes some traffic (e.g. youtube) takes all the bandwith allocated by the ISP. url...
View 1 Replies View RelatedLinksys Wireless Router :: Can't Log Into E4200
Apr 4, 2012I have a recurring issue with my e4200v1. My wired and wireless connections work fine, but I can't get to the administration website. I have https only set up, and after I get thru the 'certificate error' screen, I get an error that says web page is unavailable. Firfefox tells me that the connection was lost - error 101.I have tried wired and wireless, multiple computers, multiple browsers. I even turned the firewall off on one computer (or I think I did anyway).The only way I know how to fix it is by completely resetting then setting up the router all over again.
View 2 Replies View RelatedLinksys Wireless Router :: E4200 Wan Not Available
Jul 27, 2011Upgraded from WRT610N to E4200. Since upgrading to latest firmware the wan just disappears both 5 and 2.5 Ghz bands. Happened with older firmware but not as often. Using it in briged mode. When this happens I can't even get to the management page with a lan connected pc. Have to do a hard reboot to get it to respond again. This is unacceptable for a router at this price point.
View 2 Replies View RelatedLinksys Wireless Router :: How To Setup E4200 As WAP Only
Jan 5, 2013I am connecting the E4200 to a Sonicwall TZ100. I want the TZ100 to assign IP addresses to devices that connect to the LAN via the E4200.
How do I have the E4200 act as a WAP only or not assign IP addresses and push that responsibility to the TZ100?
I'd still want the E4200 to have a SID key for LAN access security.
Linksys Wireless Router :: E4200 Not Getting IP Address?
Dec 21, 2011I have a 6 month old Cisco e-4200 router that is updated to the latest firmware, connected to a Motorola surfboard modem on Sudden-link in Midland, TX.
I previously used this exact same setup on Cox Cable in Wichita, KS with no problems. Upon setting it up down here I cannot get the router to pickup an IP address. I have Power-cycled everything multiple times, did a complete reset and re-installation of the router software and still no luck. The Sudden-link techs have no idea what is wrong. They said that the modems signal is strong and everything should be working.
Actually I did get it to work once for a couple of days, however when redoing the surround sound system I had to unhook the cable line and it quit working and I haven't gotten it to work again since. I have tried unhooking everything. Turning it all off. Waiting for 5+minutes, and then reconnecting in order: First the modem, then an ethernet cable to the computer which will usually work. But as soon as I unplug the cable from the computer and plug it into the router it stops working.
Linksys Wireless Router :: E4200 Does Not Have Any Provision To Use MAC ID?
May 13, 2013I bought Linksys E4200, at a time that is the TOP of the line Cisco routers for Home use.I noticed a serious usage issue with it, I could not identify which are the wifi devices connected to choose for access restriction or parental controls, as the dialog box state only as "Network device", and software control by Linksys does not have any provision to use MAC ID or any other option "except " looking at the dialog box as "Network device".
View 4 Replies View RelatedLinksys Wireless Router :: Connect E4200 To A Mac Via Afp?
Mar 14, 2011How to connect the e4200 to a mac via afp? Trying to mount the network drive so the mac see it and can use for time machine backup.
View 3 Replies View RelatedLinksys Wireless Router :: Can't Update E4200 V2
Jan 3, 2013Trying to update it to the new smart Wifi but getting this error "Incorrect Image File".Yes Ive tried redownloading yes ive tried different browers and yes to unziping the file! and Yes Im downloading the correct version I even tried version 1 for the heck of it and still nothing.
View 3 Replies View RelatedLinksys Wireless Router :: E4200 V1 Tops Off At 144+450 Not 300+450
Dec 21, 2011I just received by replacement e4200 v1. I updated the firmware to 1.0.03 build 14 and am up and running just fine. The specs say e4200 should be 300+450Mbps. I am using a software "inSSider 2.0" to view my wireless setup. I get 144(N) at 2.4GHz and 450(N) at 5.2GHz. Please note these are max bit rates and not connect speed or throughput rate. The "inSSider" software gives me the following:
2.4GHz - 1/2/5.5/6/7/9/11/12/14/18/22/124/28/29/36/43/44/48/54/58/65/72/86/116/130/144
5.2GHz - 6/9/12/15/18/24/30/36/45/48/54/60/90/120/135/150/180/240/270/300/360/405/450
I get this information by hovering on the max bit rate field on the row displaying my SSID. So is it correct to say that my e4200 is not designed to reach 300Mbps at 2.4GHz. There is an earlier discussion thread about connection maxing out 144. Please note I am not talking about connect speed or thru-put speed. Max design bit rates of dual band router labeled e4200.
Linksys Wireless Router :: E4200 And Powerline Not Getting Along?
Jul 10, 2011Just got a e4200. However I also have a cisco av power line adapter which worked fine. However when connecting to the 4200 it doesn't recognize the Internet. Have rebooted, reset switched ports etc. But it still doesn't work. It sees the network but not the Internet. Have tried everything ikon but no luck. Cannot connect my directive to the Internet. If I can't get it to work will have to run a 50 foot cable.
View 5 Replies View RelatedLinksys Wireless Router :: Turn Off ULA On E4200 1.0.03?
Oct 8, 2011Firmware 1.0.00 on my E4200 Hardware v1.0 provided a functioning 6to4 tunnel through Comcast's 6to4 facility. Windows and Linux clients on my local network discovered IPv6 addresses and were able to use them successfully.Unfortunately, after the upgrade to 1.0.03 this functionality was gone. I missed reading the ChangeLog, which said that the automatic tunneling feature was removed in 1.0.01. The now provided IPv6 functionality works much less well. First, automatic configuration (discovery of the 6to4 via IPv4 anycast) no longer works with Comcast's gateway. If I configure the tunnel manually, by specifying a 2002/16 prefix, I regain IPv6 connectivity, but only for Linux clients on my local network.
Windows 7 clients suffer from the problem that because the E4200 hands out ULA addresses, they end up preferring those ULA addresses when making global IPv6 connections in the IP 'source' field, which of course does not work. It's like putting your company mailbox code as the return address on a letter you send via US Mail. Other home routers, such as the AVM Fritz! (url,...) suffer from the same problem. However, they provide an option to turn off ULA at the router.Is it possible to turn off ULA for the E4200?
Linksys Wireless Router :: E4200 Can't Log-Out Settings 192.168.1.1
Mar 26, 2012I have a E4200 router v.01 and when i updated the latest firmware (due to security exploit) it seems that whenever i acess the router settings (192.168.1.1) it doesn't ask me nor to input the admin and the password anymore, using wifi or wired.. I want the usual proccess whenever i go to 192.168.1.1 it will ask me to input my admin and password to change my router settings..
View 4 Replies View RelatedLinksys Wireless Router :: Use Cisco VPN Through E4200?
Jul 16, 2012I have an E4200 and the Cisco VPN client on my home computer that I use to access a work network. The VPN client cannot connect unless I either (a) bypass the E4200 and connect directly to my cable modem or (b) disable the SPI Firewalls on the router. I have all the VPN passthroughs set to "enable" on the router, but still cannot connect. The VPN client is using IPSEC over TCP on port 10000.
View 5 Replies View Related