I have a Linksys WRV200 and I wanted to know how can I restrict the internet speed for each computer on my network. Example: if my connection is 2 Mbps, One computer should have 1 Mpbs guaranteed, and the rest should split the rest.
View 1 Replies
WRT54GL has an option to restrict or share the bandwidth equally to each ethernet port or wireless? I need this option in a low bandwith area because the first computer connected to the router who makes some traffic (e.g. youtube) takes all the bandwith allocated by the ISP. url...
View 1 Replies View RelatedI would like to access a Digital Video Recorder (192.168.3.200 port 12088) from the internet (Telenet/Belgium). I'm using a Cisco/Linksys WRV200 (192.168.3.254) to access the internet. I can access the WRV200 remotely (from Internet) and I've created following port forwards: Port 8016-8016 >>> 192.168.3.200 Port 12088-12088 >>> 192.168.3.200 Connecting to the DVR internally is working fine but accessing the DVR from the outside doesn't work for some reason.
View 1 Replies View Relatedi have DSL router in my home using wifi by it... it is on sharing by DHCP mode. and my question is how to restrict bandwidth to other users? like full access to one use and 50-60 kbps to another user?
View 1 Replies View RelatedHow can I limit bandwidth speed of guest accounts? Or are there free softwares available to do something like that? It's kinda like the hotspot softwares - where we can set hourly, daily, monthly allowances and see a report on their connectivity.
View 3 Replies View RelatedI have a Linksys WRT54GL v. 1.1 that has been dropping connection speed (starts at 54mb, then drops to 48mbs, 36mbs, 28mbs, down to 1mbs) then disconnects, then reconnects at 54 mbs. After a short while, it will drop the speed again until it disconnects and reconnects again. This is the third Linksys WRT54GL that has done this. The first one was 5 years old before it started doing this in February, the second was 3 months old, and now the replacement Linksys sent to me is doing this?
What is going on with my router? I am able to connect fine with the Cat5 cable, but wireless seems to be the problem. Even my phone(s) get disconnected from the wireless router. This problem just recently started and I don't know why, no settings had been changed on any of the routers until after the problem had already ocurred, then the Linksys phone tech support had me make multiple changes.
I'm trying to setup a VPN Tunnel between RV082 and WRV200.The RV082 has an static IP, the WRV200 has a dynamic IP. I have to Dyndns.org in the WRV200.I have setup the RV082 tunel auth like: Dynamic IP + email.In the WRV200 I setup the hostname with the username, and the domain with the domain part of domain entered in the RV082.In the RV082 VPN Log I got: Initial Aggressive Mode message from 11.22.33.44 but no (wildcard) connection has been configured.It seems to be working the IPSEC setup but the RV082 does not accept the connection because of a missmatch in the Remote Security Gateway Type parameter in the RV082.
View 1 Replies View RelatedI have successfully connected my vpn to my central point and 2 branches.My branch can see central and visa versaMy problem is that i can't see from my 1 branch the other branch.
My central has RVS4000 and my branches has WRV200.How can i be able to access from my branch1 PC, my branch2 PC and visa versa
I have a 100mb conection and regularly get 90mb plus speed when conected direct to the modem. If I conect via the E4200 I only get 50mb ? I have tried disabling the firewall and QOS but this has had no effect. I am using a wired conection and the latest firmware. Its almost as the E4200 is capped at 50mb throughput.
View 6 Replies View RelatedIn ASA 5510. How I can limit the users in (VLAN 20) to use the internet with a limited Bandwidth/speed with 3 mbps upload and 5 mbps download?
In case the outside interface (Native vlan) which is connected to the ISP and have a bandwidth/speed of 30 mbps upload and 50 mbps download.
I'm paying for a 50 mbs connection. So what should I expect to have as a general connection speed? I know it changes depending on where you are and where your downloading from etc. But I have this old killxenos nic that might be restricting my download speed? Im getting about 3mbs. Ive gotta be able to get more then that right? Like don't tell me I'm paying for 50 but I only get 3.
View 5 Replies View RelatedI've purchased a WRT310N router to replace an existing wired router, and am in the process of setting up the outbound firewall rules. While I see settings to restrict access to all sites (or specific sites) for a specific protocol, I don't see an easy way to only allow access to one specific site.I want to restrict outbound SMTP to one server (my ISP's).
View 6 Replies View RelatedI currently use a Linksys E3200 and mainly direct connect it to my laptop. My current ISP is with Insightbb to which I use their 20.0 (20 Mbps) service. For the past 6 or 7 months I've had little to no issues with my internet connection until about a week ago. While directly connected to the E3200 I used to get up to about 20/21 Mbps at a constant rate. Yet now I'm lucky to get up to 13/14 Mbps. Also, the speed will sometimes fluctuate; shooting to as low as 8 Mbps and shooting as high as15 Mbps. I can verify that my ISP is not the issue. I've directly connected my laptop to the modem with success and received a healthy speed of up to 23 Mbps with no fluctuations. The problem only occurs once I directly connect to the router. Attempting to connect wirelessly shows the same, if not worse, problems.
I've attempted numerous factory resets and used the 30:30:30 method to no avail. I've tried power cycling the modem, router and laptop. I've tried disconnecting the router for up to 10 minutes. I've upgraded the firmware to the most recent update. I've tried setting a static IP. I've tried imputing the MTU manually. I've tried setting a MAC address clone. I've tried turning on/off UPnP. I've tried release/renewing my IP address. I've tried flushing my DNS. All of which I power cycled the router after each and every attempt.
I've recently purchased a WRT160N router, and I'm using it in conjunction with a WMP54G wireless PCI card. I've set the router up to my requirements, and can get a stable wireless connection.. but internet speed seems excessively slow. While I'm able to get up to around 4MB/s transferring files over the network, running speed tests, it consecutively shows my download speed to sit around 400KB/s, whereas I'm able to get a steady 1.1MB/s on another desktop that is wired. Disabling the LAN adapter on that computer, and connecting via wireless, brings down the speed that that computer is able to get to around 400KB/s as well. Hence, I don't think it's my wireless cards, but something to do with the router itself.I'm also experiencing lag spike issues in online games, which I can only attribute to the current wireless setup, because I've previously had no issues with it. All relevant ports are forwarded, so that is not an issue.After doing some Googling on the subject, someone had suggested running SpeedGuide's TCP Optimizer, and changing the RWIN - I ran it, and set it to the 'optimal' settings, and after a reboot the wireless seemed fine - I was getting just a tad under what I should (about 950KB/s).. but after a short while, it just went back to 400KB/s. After further investigation, it seems that Vista automatically changes that RWIN value to optimize network traffic.. but I never had this issue with my old wireless gear, so I can only assume that the way Vista is reacting is based on the way the router is interacting with it.
View 9 Replies View RelatedI have a E3000 router and I want to slow the upload and download speed to my Xbox is there any way to do this thru the router settings. I have internet that is about 20-30mbps down and 2-3mbps up I want to slow it to about 5-6mbps down and 1-2 mbps up.
View 2 Replies View RelatedI've a problem with the internet speed of my ADSL line(20Mega). Now I've the following components: D-link DSL-320 B (modem)+Cisco Linksys EA6500. If I start a Speed test the result its only 4M in download, while i remove the router and i connect my Pc directly to modem, the speed test results its 13-14M.
View 3 Replies View RelatedI came home yesterday and my Internet was really slow. I later found out that it was due to my Linksys E3000 because if I bypass my E3000 and go directly to my cable modem, it work just fine.I tried reconfigure, update firmware, factory reset and none of these has worked.
View 8 Replies View RelatedI have Wrt610n V1 Firmware V 1.00.03 B15 and internet 300 mb.If i connect PC to my internet bridge i have 300 mb. But when I switch between a WRT610n all ports have ~100mb. In router I removes all check marks from all security, filter.
View 6 Replies View RelatedI got 1Ggbit Internet. When i plug in PC i got 700+300+ on speedtest, if i plug in E3200 i got 9040. **bleep**?I play with all settings nothing works... In status he show 1 ggbit internet and 1 ggbit Ethernet but he gives less than 100 mbit....
View 9 Replies View RelatedI have an E2000 Wireless N Router setup to use WPA2/AES. I have Comcast cable internet service and I just upgraded to the 50Mbps speed. I have a Motorola Surfboard modem (DOCSIS 3.0).
If I connect my computer directly to the modem or to one of the ports on the E2000 I get great speeds sometimes up to 60Mbps but on average I am getting 45-48Mbps which is acceptable.
When I try to connect the same computer to the E2000 wirelessly my speed tests return a horrible 18-22Mbps. When I run these tests the computer is in the same room as the router. As I move throughout my house the speed tests are the same. My wireless connection speed to my laptop is good 144Mbps and 300Mbps depending on the band (2.4 or 5.0).
I have tried to use the 2.4ghz and 5.0ghz using different channels. I have also tried different "N Transmission Rate" settings. One of them (5 - 52Mpbs) does increase the speed to around 25-26Mpbs but that is all.
Strangely (or maybe not) the upload speeds are consistent on all of the tests at around 12Mpbs.
I am using Speedtest.net and Speakeasy for all of my tests.
Is there anyway I can get my wireless download speed up to around 40Mpbs? Or am I going to have to run cables through my house to the devices where I need these high speeds?
I also have upgraded to the latest firmware version.(1.0.04)
We recently purchased a Linksys E3200 router, because our old router didn't take advantage of our internet speed. The router works fine, though the internet speeds again isn't as much as expected.
With a wired connection, we only get 80 Mbit/s of our full 120 Mbit/s, according to Speedtest.net. The Cisco Connect built-in speed test is even worse; only 40 Mbit/s. When we directly plug the computer into the modem, we get the full 120 Mbit/s, which indicates that the modem does have the connection speed. The router just doesn't give it to the computers attached.
I don't know about my wireless speed, as my wireless card in the laptop clearly is the bottleneck (it can only connect at 65 Mbit/s). Atheros AR9285 ftw.
We tried different cables, the one included with the router gives the same speed.
I just bought a Cisco e1200 router... and the wireless connection is way too slow, when navigating through the web, but when using speed test, the connection seems fine, but still it even takes more than usual to open simple pages, lets say Google... i usually watch streams and now that i cannot do... when i connect directly i can do everything as usual...as i have read, i change channels, but still no improvement, i have the latest firmware, on my range there are only 2 more available connections... i even tried disabling/enabling the WMM... We all know that having extremely slow internet must be the real "Mayan apocalypse"
View 2 Replies View RelatedI have a Cisco E1000 v2. I updated to the latest Firmware 05/25/2011Ver.2.1.02 (Build 5).
Before doing this update I did get 300mbps N speeds. Now I don’t using the same settings, it max out at 144mbps speed. Also the router only seems to get B speeds when using a channel other than 11. I did do a hard reset after the firmware update.
With M10, I cannot restrict internet access for specific time period. Parent Control feature doesn't satisfy the situation, and there is no build-in access-policy in web-based setup. Are you going to upgrade firmware or Cisco Connect with more flexible access time control?
View 1 Replies View RelatedMy Cisco E3000 has slowed it's Ethernet speed so slow that it times out when going to Facebook, YouTube or any site that is complex. It worked fine until one day it just gave up. It's connected to DSL Modem with Ethernet To a Apple Mac G5 power PC There are two other older macs connected via Ethernet, same problem. When I took the router out of the chain, and connected G5 directly to modem, normal internet speed. My firmware is up to date. Both wireless bands work great. When I look at Cisco Connect, everything looks normal. factory settings.
View 7 Replies View RelatedIf I connect wire directely to the PC Ethernet port the Internet speed is about 400 Mbit/sec (speedtest.net)When my PC is connected through the Linksys E4200 Internet speed is not above 90 Mbit/sec.
View 1 Replies View RelatedMy ISP provides me internet by pppoe connection.When testing the connection with the router i get 30 mbps.When testing the conection without the router, cable conected to laptop i get 60 mpbs.
View 1 Replies View RelatedI own a ea4500 wireless router, I have tested the speed at speedtest.net and wirelessly I get around 9 mbps. My speed is 23 mbps when I hard wired the pc. I have check the speed on a tablet ( android ), pc and a mac to about 5 feet away from the router with no walls or anything between the two devices.I have checked all the settings but I don't see anything wrong, I have changed to N mode only to make sure I use top speed.All my devices are able to use N.
View 3 Replies View RelatedI just recently purchased comcast internet today and self installation kit that came with the modem and all..... got it all set up no problems activated did speed test directly from cable modem to laptop computer wired and was getting 10mbps down and 3mbps up well went out and bought a linksys e900 wireless router.... connected it no problems... however my laptop wireless and phones connected to the router with speedtest is only getting 300kbps down average!!! but the upload is still 3mbps.
View 9 Replies View RelatedI have the WRT54G v2.2 router. I have Comcast internet service. Comcast has just increased their internet download speed to 50Mbps. With a wired computer (not wireless), connected directly to the router, the fastest internet download speed I get is 30Mbps. When I called Comcast's technical support, they are telling me I need a new router as the older routers can't handle these high internet speeds.
View 2 Replies View RelatedIn 'Status' on my router there is a green dot in the field below 10/100 mbps at 'Internet port speed' - shouldn' that dot be below 1 gbps?
View 1 Replies View RelatedIt is the router Cisco Linksys E4200.
My situation before I bought the router:
- my Internet speed is 120/20 (Mbps download / Mbps upload)
- speed test with my ISP gives 125/20 for 99% of the tests- speed test with [URL] gives 125/20 for 99% of the tests
- I never have had a router; my PC is connected directly to the cable modem
- My ISP is Vidéotron from Quebec in Canada : [URL]
My new situation with the new router :
- last Tuesday, I bought the router Cisco Linksys E4200
- the installation went fine and Internet works well
- during the installation process, the firmware is upgraded to 1.0.03
- speed test with my ISP gives 100/20 for 99% of the tests
- speed test with [URL] gives 100/20 for 99% of the tests
My observations :
- according to router status port, Internet port is 1 Gbps
- according to router status port, port 1 (where my PC is connected) is 1 Gbps
- it seems that speed cannot get more than 100/20 with the new router
- when I disconnect the router and I reconnect my PC directly to the modem cable, I still get 125/20
Calling Cisco support :
- Many tests are done during 3 chat sessions
- The speed is still 100/20
- The recommendation is to replace the router with a new one
Friend support :
- A friend of mine brought his router which is the same as mine- The speed is still 100/20 with his router
New router :
- As recommended by Cisco support, I got the router replaced from the store.
- I installed the new router
- During the installation process, the firmware is not upgraded; the firmware is 1.0.01
- The speed is now 125/20
- I upgraded the firmware to 1.0.03
- The speed is now 120/20
- I downgraded the firmware to 1.0.01
- The speed is now 125/20
Conclusion :
- My speed is maximized at 100/20 with the firmware 1.0.03
- I will stay with firmware 1.0.01 until firmware1.0.03 is corrected.
I have a WRT54G router and for some reason I'm unable to receive the media stream at my home, but when I connected to my friends N-type router it works fine. I have no other connectivity issues. The only thing that I remember doing that may have caused this was to upgrade my firmware because my droid phone wouldn't connect.
View 8 Replies View Related
