Linksys Wireless Router :: E3200 - Internet Speed Drops?
Jul 17, 2012
We recently purchased a Linksys E3200 router, because our old router didn't take advantage of our internet speed. The router works fine, though the internet speeds again isn't as much as expected.
With a wired connection, we only get 80 Mbit/s of our full 120 Mbit/s, according to Speedtest.net. The Cisco Connect built-in speed test is even worse; only 40 Mbit/s. When we directly plug the computer into the modem, we get the full 120 Mbit/s, which indicates that the modem does have the connection speed. The router just doesn't give it to the computers attached.
I don't know about my wireless speed, as my wireless card in the laptop clearly is the bottleneck (it can only connect at 65 Mbit/s). Atheros AR9285 ftw.
We tried different cables, the one included with the router gives the same speed.
View 9 Replies
ADVERTISEMENT
Mar 7, 2012
Got a Linksys E3200, and a gigabit card, even two, Realtec and Intel, have a connection ggbit. If the power cord plug directly into netcard, all at great, the tracker up to 80 MB per second, shakes on speedtest.net, shows 780 240 + Mbps. When i connect my inet through the router, the speed drops to 12 MB(100 Mbit) and speedtest the same, but in the the web interface in the statistics shows that everything is connected to a gigabit.
Plus, when I ping my ISP's website (ip -t ) and assume [URL] click on the test, the router with 1ms pings are beginning to rise to 30 ms, and when it is directly in netcard, it stable 1ms.... When through the router, torrent shake it just do up to 100ms jumps. I have all the settings , and set up his hands, and a manager, all for nothing. It started five days ago, before that everything was ok. Can a router burn? Rather it gigabit controller?
View 4 Replies
View Related
Mar 4, 2012
I currently use a Linksys E3200 and mainly direct connect it to my laptop. My current ISP is with Insightbb to which I use their 20.0 (20 Mbps) service. For the past 6 or 7 months I've had little to no issues with my internet connection until about a week ago. While directly connected to the E3200 I used to get up to about 20/21 Mbps at a constant rate. Yet now I'm lucky to get up to 13/14 Mbps. Also, the speed will sometimes fluctuate; shooting to as low as 8 Mbps and shooting as high as15 Mbps. I can verify that my ISP is not the issue. I've directly connected my laptop to the modem with success and received a healthy speed of up to 23 Mbps with no fluctuations. The problem only occurs once I directly connect to the router. Attempting to connect wirelessly shows the same, if not worse, problems.
I've attempted numerous factory resets and used the 30:30:30 method to no avail. I've tried power cycling the modem, router and laptop. I've tried disconnecting the router for up to 10 minutes. I've upgraded the firmware to the most recent update. I've tried setting a static IP. I've tried imputing the MTU manually. I've tried setting a MAC address clone. I've tried turning on/off UPnP. I've tried release/renewing my IP address. I've tried flushing my DNS. All of which I power cycled the router after each and every attempt.
View 1 Replies
View Related
Feb 24, 2013
I got 1Ggbit Internet. When i plug in PC i got 700+300+ on speedtest, if i plug in E3200 i got 9040. **bleep**?I play with all settings nothing works... In status he show 1 ggbit internet and 1 ggbit Ethernet but he gives less than 100 mbit....
View 9 Replies
View Related
Apr 26, 2012
My ISP provides me internet by pppoe connection.When testing the connection with the router i get 30 mbps.When testing the conection without the router, cable conected to laptop i get 60 mpbs.
View 1 Replies
View Related
Jul 4, 2012
I got an E3200-RM (refurbished).
I did not do a MAC Address Clone, when I connected it I just called my ISP and they enabled it. Internet connection with all devices right there, no problem.
Problem started next day, every day I have to do a hard reset because when I wake up I have no connection with all devices (1 Ipad, 2 Iphones, 2 PCs, 1 Xbox 360, 1 PS3): My SSID is seen on the network but no device can connect to it.
I changed the Channels to manual as said on other threads, but didn't work.
In addition to that, when I try connecting my PC with the ethernet cable to the router -instead of wireless-, I have no internet connection on the PC and any other device that I try to reconnect to the router wirelessly can't connect anymore (have to do a hard reset again and unplug the ethernet cable).
the WRT54G worked perfectly for me...
View 6 Replies
View Related
Jun 5, 2012
I have a E3200 and upgraded the firmware last weekend to 1.0.0.4 and now I get dropped connections every few minutes. I was working form home and VPN into a west coast client and was getting dosconnected every few minutes so I thought it was possibly their VPN but when I checked my outloook it was also disconnected and is not associated with their VPN. I called Comcast and they said the modem has been online for 19 days so now everything points to the router.
View 5 Replies
View Related
Feb 1, 2013
Running Windows 8--64 bit computer, with a SBV4200 Voice over IP cable Modem (Time-Warner Communications), in home network. Longstanding problem with Ethernet connected computer losing connectivity to E3200. Connectivity reestablished by powering down, cutting power to cable modem, computer, and E3200, and restarting. Other wireless connections (iphones, ipad, other dos -based laptops have no problems--never any loss of connectivity. Things I have done to date: removed Linksys E-series software and reloaded, updated drivers, changed all wiring to router, and checked IP addresses and they are different.
View 2 Replies
View Related
Apr 13, 2012
I have a problem with low throughput E3200 router. I have about 250 Mbps speed connection by Cisco EPC3925 cable modem. If I connect my computer directly to the cable modem, I can easily obtain the speed of downloading data from a fast servers about 200 Mbps and even more. When I'm connecting through E3200 I can get about 80-100 Mbps when downloading data from the same sources. I have tested this on few computers with different operating systems (Win7, Mac OS X) and there is no change. Between the cable modem and the E3200 router the cable link is @ 1Gbps. Also, between the computer and the router is a 1Gbps link. If i change router E3200 for cheaper and weaker model WRT320N then I can easily get about 200Mbps.I have the latest available soft in my router E3200 (1.0.03). I'm disappointed with low productivity, this router is not cheapest one
View 8 Replies
View Related
Jun 10, 2012
my Linksys E3200 router is somehow slowing my internet download speed by a lot. Direct wired connection from computer to modem gets me around 200Mbps download speed, but if I connect thru my Linksys E3200 router (wired connection, not wifi), the download speed goes down significantly to ~70Mbps. The E3200 is only connected to the modem and my computer (i.e. I have unplugged all other devices from the E3200 router). Are there setttings in the E3200 that can potentially cause it to limit the speed or could this be caused by something else?
View 4 Replies
View Related
Aug 11, 2011
I purchased a new router - cisco e1000. Currently, i have 2 laptops wirelessly connected to this router. When i do a broadband speed test, the speed drops down significantly to 8MBPS while if i connect it to the cable modem directly (wired) i.e., without router, i'm getting 15 MBPS download speed. I did a couple of times this speed check and the results are same. I tried changing the advanced settings in the router (which was specified in one of the post in this forum) but no luck. Is it that i need to buy e4200 to match the wired speed of 15 MBPS or what other things I can do to get the same speed of my cable modem (provided by my ISP)?
View 1 Replies
View Related
Nov 5, 2012
I'm running a Cisco E4200V2 router with the latest firmware (2.1.4.12284) on an iMac running OS X 10.8. My ISP is providing 15Mbps to my modem, which I've confirmed by connecting directly to it without the router. Once I put the router back in the path, my broadband speed drops to about 6 Mbps. Is this the best I can expect from this router?
View 2 Replies
View Related
Dec 21, 2011
I have four E4200's doing the same. I have FiOS 15M download and 5M upload. As soon as QoS is turned on the upload speed drops down to usually 300k and it never exceeds 1M.At the same time any VPN connection gets dropped often.I also configured one E4200v1 as router and the second E4200v1 as Access Point (HDCP off) hardwired to the first one.Any VPN connection gets dropped when changing location. I.e. if VPN was established with the router, the connection gets dropped when in the location where AP is -- and the other way around too. There is no coverage gap between the two locations, to the contrary - they do overlap heavily.On Dec 21, 2011 the level 2 Linksys/Cisco people advised that they will forward the two issues to engineering and that resolution will be within 24-48 hours.
View 5 Replies
View Related
Aug 10, 2012
I am using linksys cisco wag120n adsl2 modem router.When I start the router the internet speed seems great but after some time the speed drops miserably. When I again restart the router the speed seems great for few mins but again drops after sometime.It happens in both LAN and wireless mode.The firmware version of the router is 1.00.16
I was going through the problems posted by some other user but observed that cisco people are not heraing to them.Seems made a mistake by associating with cisco product.This is the worst router I have ever used.The wireless also gets disconnected abruptly.Next time I'll avoid cisco.Cisco is all about stone age products and zero customer care.
View 1 Replies
View Related
Apr 16, 2012
My problem occurs when i am trying to download something big, mainly the speed of the download raises at a peak and then it drops disconnecting me from the internet for a few seconds. This only happens when my laptop is on a wireless connection and this phenomenon repeats itself untill the download is complete. During the connection crash I am not able to access any site.
My laptop is an Asus G series with Win7 64bit SP1, and I use utorrent for P2P downloads.
View 1 Replies
View Related
Jul 23, 2009
I have had the DIR-825 since the beginning of the year connected to AT&T DSL Internet 3GB. I just upgraded to their 6GB download speed and didn't see any change in speed and suddenly I couldn't view my SlingBox anymore outside the house. I connected one computer directly to the modem, ran the AT&T speed test and got >5GB download and @700 upload. Wired via 1GB network back to the router, ran the speed test and it dropped to @4GB download and 120 upload.
I called AT&T, they checked everything, and said there was nothing wrong. I then spent almost an hour on the phone with D-Link including getting passed to 3rd level support. I knew something was wrong when the guy told me that since it was only a 1GB router, I shouldn't expect to get faster than 1GB Internet download.
The router is still running the 1.00 firmware and these are the changes they made me try so it's still sitting at these settings:
- Change the WAN from Auto 10/100 to 100 only.
- Change MTU to 1482 in my PPPoE settings
- Change Firewall Settings to turn SPI off. He said the router is still providing a firewall though.
He wanted me to download the 1.01 firmware but I balked and he said it probably wouldn't do any good. It ended with him wanting me to call AT&T back and set the modem to bridge mode. I then need to call them back and set the PPPoE again. This 3rd level support guy was very rude and am hoping to avoid calling them again.
Before I go through the hassle of calling AT&T and trying this bridge mode, or has the Elite 6GB service from AT&T and are having it work correctly.
View 15 Replies
View Related
Oct 25, 2007
Networking isn't my strongest computer subject area, but I know I'm having a performance problem with my RV082 router. When I direct connect my PC to my cable modem, I can get very near the 7mb/sec rate advertised by my ISP. When I connect the modem to this router, then connect to the pc to the router, the speed drops to between 2-3mb/sec. All tests performed several time using dslreport.com speed test website. The result is very repeatable, so I figure it has to be some delay introduced by the router. I can't see to find any place in the router configuration to do performance tuning. I'm not using any firewall rules except for the default rules. Why I'm seeing a greater than 50% decrease in internet throughput using this router?
View 8 Replies
View Related
Dec 18, 2011
The problem I have was that last night I unplugged my router and replugged it back in. As soon as that happened, there was no connection between my router and the modem. This morning, I tested to see if it was the modem by connecting an ethernet cable from my desktop to it, and was able to get online. Then, II reset the router and a sucessful connection was made between the two. On my desktop my old network was gone, but the Cisco network was there, leading me to create a new network as if it was a new router. After setting up a new network, I am not able to connect to the internet.
View 1 Replies
View Related
May 14, 2011
I have purchased a new E3200 to replace my old Linksys router. It locates my computers and sets up a network, but cannot connect to the internet via my Comcast cable modem. I have read on this forum about Mac address issues, but it has located the Mac address. The internet IP address is all zeros, and releasing and renewing the IP does nothing
View 9 Replies
View Related
Jun 17, 2012
I have a Telus Wireless modem and got a linksys router to try and expand the range & strength of the wifi. However,whenever I plug in the router and try to set it up, I can get connected to the router but no internet connection.I have tried everything I can - restarted the modem and the router several times, connected and reconnected, rebooted the whole of the router system, connected with an ethernet cable straight to the router from my laptop. In the settings, I have tried to mess around with the settings and more, and whenever I screw up I reset the router to defaults again.
View 3 Replies
View Related
Jan 3, 2012
I have was that last night I unplugged my router and replugged it back in. As soon as that happened, there was no connection between my router and the modem. This morning, I tested to see if it was the modem by connecting an ethernet cable from my desktop to it, and was able to get online. Then, II reset the router and a sucessful connection was made between the two. On my desktop my old network was gone, but the Cisco network was there, leading me to create a new network as if it was a new router. After setting up a new network, I am not able to connect to the internet
View 3 Replies
View Related
Oct 5, 2011
Is it possible to connect the E3200 Router to the internet over the wifi (WLAN) interface?Actually I can only use the ethernet port called "Internet" to connect with my Fritz Box router (which is responsible for my internet connection to my DSL provider).But I don't want to use 10m or more ethernet cable across my flat so it would be nice to use just wifi.
View 5 Replies
View Related
Feb 26, 2012
My new e3200 setup just fine with Cisco Connect. I have consistently good speeds with a direct ethernet connection, but the wireless speeds fluctuate widely. When I power cycle the router, I'll have perfect speeds for a few minutes and then it'll slow to a crawl (approx 0.5Mbps). Then for no apparent reason, it will speed back up to normal, and then back down to a crawl. I'm using the latest firmware and have allowed Cisco Connect to manage the router so far.This is actually my 2nd router, as Tech Support told me when I experienced this with the first router that it was defective, but I'm seeing the same problem with the 2nd router, so I know something isn't quite right.
View 2 Replies
View Related
Jan 24, 2012
I have a problem with my E3200 that has happened at least 4 times since I first purchased, installed and configured it. Initially I thought it might be something with Comcast, but a) I never had the problem with my Linksys WRT54G router and b) It seems I can now duplicate the issue by saving a config file and restoring it.The specific issue appears to be somewhat random. At some point the connection to the Internet simply stops for no apparent reason. I am able to ping the router and connect to it. I am also able to drop and renew connections to the cable modem successfully. Furthermore, I can ping my network side of the router, as well as the external address handed to my router by the cable modem, and the cable modem gateway address, but still no connection to the Internet.The only solution to my problem has been to restore the factory defaults to the router and reconfigure it from scratch, which does seem to fix the issue for a time until it occurs again. FYI, I do not use the Cisco connect software because I have several custom port and QOS configs that are necessary for an IP Phone and other hardware on my network.
View 1 Replies
View Related
Jul 27, 2012
My E3200 (firmware 1.0.04) loses access to internet every week or so and OK again when reboot.
View 6 Replies
View Related
Jun 23, 2012
i am a total n00b when it comes to wireless routers etc,.. i bought this router [E3200] about six mths ago, it has been working just fine untill a couple days ago, wher i woud be on the internet and all of a sudden, the internet connection drops, i am using a cable modem [ARRIS TM722G] ,i did a reset on the e3200 and put restore the settings that did last over night
View 9 Replies
View Related
Feb 13, 2012
Ok, so I recently upgraded to a Linksys E3200. I am trying to get the QoS to work properly. I know that it is supposed to prioritize network traffic, so that if I have busy traffic but I am playing an online game, it should keep my gaming from stuttering while slowing other traffic down.
The problem is that every time I enable QoS everything slows down dramatically. I had a 200MB download that was going to take 5hrs with QoS enabled, that took 10min with QoS disabled. And with QoS enabled I can't even watch a youtube video without it pausing to buffer every 10 seconds. And that was the only PC/device using the network at the time. Again turning off the QoS WMM option solved the problem. I have noticed this problem with multiple routers and brands and usually just disable QoS as soon as I set up a router, however I heard that I won't get the full benefit of 300Mbps without QoS enabled.
I don't have any special Voice over IP needs, or video streaming etc. and I rarely am using multiple network devices at the same time. Is there really any reason I should enable QoS? Also I never really play with the settings for QoS, I just figure that since it comes enabled by default it should work for the average consumer.
View 9 Replies
View Related
Feb 7, 2012
I used these instructions to put my Fairpoint westell 7500 modem/router into bridge mode: [URL]. Then I hooked my new e3200 to the westell 7500, but no matter what I tried, I could not get any PCs hooked to the e3200 to be able to get to the internet.so able to get to internet too. My questions are:Is there any downside to doing it this way? (ie, not putting westell in bridge mode).Can this cause any slowness or conflicts? Any reasons why bridge mode may not have worked?
View 4 Replies
View Related
Oct 29, 2011
I justed purchased a Linksys E3200 router to replace my old router that gave up the ghost. I have it paired with a Motorola 2210-02 DSL modem. The software that came with the router has created two networks but is unable to connect to the internet. I have tried on both my PC and MacBook Pro and niether work. I have the modem connected directly to my Mac and can get to the internet, so I know the modem is working correctly.
View 6 Replies
View Related
Dec 4, 2012
I have a Linsys E3200 router for almost a year. It's been working fine until recently. It kept losing internet connection every a couple hours or even shorter. I have to power cycle the router in order to make it to work. However, sometimes that won't work either. I also tried to restore the router to the factory default but that doesn't seem to work.
I have updated the router with the latest firmware (1.04). I am using a cable connection and it never gives me any problem if I just connect my computer to it. I also test my network with another old netgear router that works just fine.
View 9 Replies
View Related
Jan 1, 2013
I recently replaced an old Linksys with a Cisco E3200. All our devices get "stuck" periodically and can connect to the E3200 but not the internet. We power cycle the E3200 and all is fine. But only for a period of time, then we need to power cycle again. The range is less than my 4 year old Linksys was also, devices maybe 30 feet lose their connection even more quickly, forcing more frequent power cycling.
View 2 Replies
View Related
Dec 10, 2011
E3200 works great until I enable QoS. The device uses QoS and works find until reboot. If QoS is enabled and the device is rebooted, its stops routing from LAN side to Internet side. Administration-->Diagnostics allow me to ping/trace route to Internet sites and local LAN clients but cannot reach Internet from local LAN.
Windows networking icon indicates "No Internet access". I can ping other devices on local LAN.
Disabling QoS restores routing and you can re-enable QoS after that and all is well. Unfortunately, if there is a power failure when I', not there to disable/re-enable QoS afterward, other household members can't use the Internet till I get home.
Wondering if any other QoS users have observed the same problem.
View 7 Replies
View Related
Mar 20, 2013
I bought a Cisco-Linksys E3200 8 months ago and it worked well until last month. I usually power down the router after midnight & power up in the morning and evevry time it can connect to internet through DSL modem without problem until this Feb. Most of the time after powering up the router it just can't connect to internet anymore. I am sure the AT&T DSL modem is working. I have to reboot/reset the router & DSL modem several time to get router to connect to internet again. The order of resetting/rebooting DSL modem & E3200 router seems to make no difference. It just appears suddenly the router can connect to internet by chance. I changed router IP and it didn't work either. It's really annoying becuase I have to spend 10~40 minutes to resetting/rebooting DSL modem & router to get internet connection every day.
View 9 Replies
View Related
