Linksys Wireless Router :: E4200 Not Allowing Full Internet Bandwidth

Oct 16, 2011

I have a 100mb conection and regularly get 90mb plus speed when conected direct to the modem. If I conect via the E4200 I only get 50mb ? I have tried disabling the firewall and QOS but this has had no effect. I am using a wired conection and the latest firmware. Its almost as the E4200 is capped at 50mb throughput.

View 6 Replies


ADVERTISEMENT

Linksys Wireless Router :: How To Use Full Wifi Bandwidth Of E1200

Oct 31, 2012

I just bought a E1200 routerand using automatic setup by using CISCO connectafter that, I only got a CONNECT SPEED with about 10Mbps in my android smart phone,I would like to know how can I increase the WIFI strength WITHIN THE WIFI SETTING, I chose MIXED mode rather than specific in b/g/n mode.

View 4 Replies View Related

Linksys Wireless Router :: E4200 - Stopped Allowing Traffic Through Ports Completely

Apr 24, 2013

I posted my complaint on Amazon.com recently.  My E4200 router stopped allowing traffic through ports completely.  I was able to unplug the power and allow the router to cool, and the router would work for a while then stop after about 10 minutes.  I assume that the unit was overheating, but I do not have the equipment of a test facility.I bought a Belkin AC 1200 router which is a bit of an upgrade from Amazon.com.  I do not think that there is anything that Linksys can do for me as my warranty expired.  I just thought that when I spent what was to me a lot of money the router should have lasted longer.

View 5 Replies View Related

Linksys Wireless Router :: E4200 - DSL Modem In Bridge Mode Reports Full Speed

Dec 21, 2011

I have a d-link dsl modem that reports it's getting the full 6 meg download speed from AT&T.   I put the dsl modem in bridge mode so the E4200 will do the logon to AT&T with my credentials.   If i do a speed check using CNET internet speed test, from both a desktop (wired 1gb card) and any laptop in the house (all draft n 2.4 or 5.0), it ranges anywhere from 3 meg to 4.3 meg.   I have 6 cat-e ethernet cords everywhere.   I do have 2 switches but have tried to unplug those to see if any difference

View 1 Replies View Related

Linksys Wireless Router :: Add A Bandwidth Meter For E4200?

Mar 3, 2011

I would love to see this added in a future firmware release. I imagine others would welcome it as well that have caps with their isp.

View 9 Replies View Related

Linksys Wireless Router :: E4200 V1 QOS Can Add Downlink Bandwidth?

Jun 8, 2012

E4200 V1 QOS can  add downlink bandwidth?

View 3 Replies View Related

Linksys Wireless Router :: E4200 Cuts Bandwidth By Nearly Half

Dec 16, 2011

I just signed up for Charter's Ultra 100Mbps internet service.  We confirmed it worked at that speed by connecting my Lenovo T520 laptop directly to the Motorola Cable modem.  I acheived just over 102Mbps throughput down.Next, I plugged in the e4200 (v1) router to the modem, and the computer directly to that (wired), and the max performance I could see was right around 52Mbps.  Wireless performance on wireless-n, 5Ghz, maxes out at around 42Mbps.I am concerned about the throughput dropping from 102Mbps to 52Mbps while directly WIRED to the router.  That tells me that the router is definitely capping my throughput. I have turned off QOS, found the optimum MTU of 1468 (used the ping -f -l 1440 [url]...) to find the largest MTU that didn't spit out a fragmented message, and added 28 to that.
 
I am a bit baffled that this top of the line router which some have claimed to see >100Mbps performance over wireless alone, isn't able to achieve any higher than 52Mbps wired. I do have other devices plugged in, but none actively transferring. What could be capping the throughput?  The router worked fine on 25Mbps service, but it seems unable to handle 100Mbps service.

View 3 Replies View Related

Linksys Wireless Router :: E4200 V2 - Limit Bandwidth On Particular Device?

Jul 6, 2012

I want to know how I can manually limit the Kbps for a particular devince in the QOS.I DO NOT want to simply set the priority (low/med/high). I want to "physically" limit a device.
 
When I select to do it manually (upstream bandwidth) it limits ALL devices and I do not want this. I want to limit the bandwidth on only one device that is connected (ie an Xbox)
 
I have a Linksys E4200 V2

View 9 Replies View Related

Linksys Wireless Router :: E4200 V1 Cannot Seem To Find Work Around For Wifi Bandwidth

May 2, 2012

I recently bought myself the E4200v1 router, and have had several issues with it. One issue I cannot seem to find a workaround for is the wifi bandwidth problem.I have a 100/10 mbitl internet connection. The router claims to support 300/450 mbit speeds over wifi, so that should be plenty. in reality however, that isnt so.Even though my N-standard wifi adapter on my machine states it has a 130 mbit connection to the router, I consistently test the internet throughput when using wifi and speedtest.net to around 20-21 mbit. If I put in a cable, I instantly get full speed, 100/10 mbit.
 
Have to add; I am not new to the networking game, I have a CCNA and a degree in computer sciences, and work with hosting web sites using cloud tech every day. At this point, I have tried everything related to settings on the router, so I can only conclude that there's some kind of bug in the firmware. I would expect the standard firmware to work, and not having to install DDWRT or other custom firmware.

View 7 Replies View Related

Linksys Wireless Router :: EA4500 - Allowing Vizio Internet Apps To Connect From Two Different TV's

May 28, 2012

EA4500 Linksys router stopped allowing vizio Internet apps to connect from two different TV's. Problem, Just got brand new EA4500 router and Motorola SURFboard DOCSIS 3.0 High-Speed Cable Modem Model: 575319-019. I have 2 new vizio big screen tv's with internet apps. All was working fine and had no problems but occasional drops or limited access.
 
One day BOTH TV's could no longer connect. However, The tv's will connect to another access point. therefore the problem does not exist in the TV/s and has to be a problem in my access point (I.E. Router allowing access). Additionally, all other devices connect and work fine. I have already unplugged everything for an extended period of time. Checked for updates on firmware and verified no software needed to be updated. Rebooted router... Am using wpa-psk and feel i shouldn't have to go weep as it was working fine...

View 3 Replies View Related

Linksys Wired Router :: BEFSR41 Disconnected From Internet While Allowing UPNP

Oct 29, 2011

I have a Linksys router (model BEFSR41) and I all the outputs going to two computers and two gaming systems (X360 and PS3). I have had the router for over a year and it works fine, but I recently decided to attempt to have my 360 access the media on my computer by linking the two together through the Media Center. To do this, I needed to enable my router to allow UPnP (according to Microsoft help). When I did enable this, the router would disconnect me every 2-5 seconds from the internet, then would reconnect me right away.I have no clue why it was doing this (it occured across all of my devices) so I just disabled UPnP and things went back to normal. How to fix this so that I can have a consistent and stable connection when I have UPnP enabled? 

View 1 Replies View Related

Linksys Wireless Router :: WRV200 - Restrict Bandwidth / Internet Speed?

Jun 17, 2012

I have a Linksys WRV200 and I wanted to know how can I restrict the internet speed for each computer on my network. Example: if my connection is 2 Mbps, One computer should have 1 Mpbs guaranteed, and the rest should split the rest.

View 1 Replies View Related

Cisco Firewall :: ASA 5505 / Unable To Use Full Bandwidth?

May 23, 2011

When I have a computer directly connected to the Cable Modem I get 9.84MB Down and 1MB Up. When I put it behind the ASA 5505 with policing on the interface, I only get 4MB Down and 660Kb Down.What I'm wanting to do is setup this up to enable my VoIP to have a higher priority and shave 128kon both the Up/Down for the VoIP traffic. I also want to make sure I don't exceed the inbound and outbound thresholds.I''m using a 5505 Security Plus?

View 3 Replies View Related

Unresponsive Router - Stopped Allowing Wireless Internet Access

Nov 3, 2012

My Netgear wireless router had been working just fine and then inexplicably stopped allowing wireless internet access. My modem is fine. I contacted my internet service provider, and no luck. I unplugged the router's power source and plugged it back it in. Still not working. I switched the power on and off. Nothing. I do not know what to try next.

View 1 Replies View Related

Cisco WAN :: How To Make Use Of Full Bandwidth Catalyst 3560 Series

Feb 10, 2013

I have two Catalyst 3560 series switches with a 100Mb Ethernet microwave link and a 250Mb Ethernet microwave link between them. Can the switches be set up to make full use of the added bandwidth (350 Mb).

View 3 Replies View Related

Linksys Wireless Router :: WRT54GH-SG Not Allowing To Logon

Nov 16, 2010

I'm not able to logon to WRT54GH-SG over 192.168.1.1. I'm using correct password & have NOT forgotten. I'm hitting 401 page. The support rep told me reset the router which I do not want to before I explore any possibilities.

View 8 Replies View Related

Linksys Wireless Router :: E4200 LAN And AP Does Not Access Internet

Jun 18, 2012

I have my main router, a E4200v2 which I use as a router and it provides wireless signal throughout my house, however reception is not as strong on the upper floor and there is a slight dead spot, so I purchased an E4200 for the uppermost floor.I set the E4200 to bridge mode so it will act solely as an AP.However connecting the two routers LAN to LAN and the AP does not access the internet.Setting a static IP for the router, instead of acquiring one via DHCP causes me to not be able to access the admin page on the AP.
 
Connecting WAN on the E4200 to the LAN on the v2 does not work either.My goal here is to have my main router on 192.168.1.1 and the AP on 192.168.1.2 where I can access the admin settings for both routers in case I need to make changes.

View 9 Replies View Related

Linksys Wireless Router :: E4200 - No Connection To Internet?

Apr 21, 2012

I have my e4200 connected to another modem/router (2Wire 3600HGV), because the other router does not support Wireless N. I can connect to my E4200 network, but there's just no connection to the internet. I reseted my e4200 but still no luck. I've unplugged both routers and replugged them, nothing. I know it's possible because I've had it set up before but I had my 2Wire exchanged for a newer one.
  
Firmware: 1.00.4
 
Just to be sure. I have the cable going from my modem out of port #1 and into my e4200 where it says internet, thats correct, right? On my e4200 i have the IP 192.168.1.2 but on the 2Wire I have the e4200 as 1.92.168.1.66. 

View 1 Replies View Related

Linksys Wireless Router :: E4200 Internet Keeps Dropping

Apr 1, 2011

e4200 internet keeps dropping

View 9 Replies View Related

Linksys Wireless Router :: E2000 Not Allowing Access To Other Devices

Nov 5, 2011

I just set up my e2000 on a PC using Windows 7.  I am additionally trying to set up additional devices on the network.  The two that I am currently working with are:Dell Latitude d240 running Windows XP.HTC Evo smartphone running Android
 
I can't get these on the network through the e2000.  They can access the internet through the e2000 but only as a guest and therefore don't have the same level of security.  What do I need to do to successfully put the above devices on the network?

View 2 Replies View Related

Linksys Wireless Router :: E4200 - VPN Is Disabling Internet Access

Sep 26, 2011

I have a Linksys E4200 router with firmware version 1.0.02. I am using a Macbook Pro. I can connect to a VPN server with the default VPN client software, but it kills my internet connection and disables connecting to SMB

View 5 Replies View Related

Linksys Wireless Router :: E4200 Internet Connection Fails

Jan 1, 2013

I have a E4200 V1 with firmware 1.0.0.5 installed The problem is that when I connect the cable from my modem to my router and recycle both I get a rapidly fashing Cisco light and can not connect to the internet.If I remove that cable and recycle the router my network works but (obviously) I have no internet connectivity.This was working (almost 2 years) without issue until today.I updated the firmware and did a factory reset and neither resolved the issue.My next experiment is to see if I can't get log files (since the factory reset) but I can't do that at this time.

View 3 Replies View Related

Linksys Wireless Router :: E4200 Doesn't Connect To Internet

Jul 9, 2011

I have a Motorola Docis Surfboard model Model SB6120 and can connect to the internet with the ethernet cable directly onto the labtop but if I connect it to the E4200 router the range is there but the internet connection is not.  This happened 2 days ago and can't get the router to work.

View 4 Replies View Related

Linksys Wireless Router :: Cannot Setup E4200 - No Internet Connection

Aug 9, 2011

I just purchased e4200 from a friend of mine. Got an issue with setup of this device. I use a model from internet provider. Have 2 computers at home. One is pc with cable, another one mac with wireless.SO my issue is that i can not connect none of them. I was trying to use cd that comes with router but he can not locate a router. When I connect cable directly from modem to computer everything works fine. As soon I connect cable to a router I can not see a router and I can not connect to internet.

View 1 Replies View Related

Linksys Wireless Router :: Internet Modem Won't Read E4200?

Jun 28, 2012

My internet modem won't read my E4200 router. How do you reconfigure the settings?

View 2 Replies View Related

Linksys Wireless Router :: E4200 Couldn't Connect To Internet

Feb 25, 2011

I have put two different e4200 routers in my network and both of them have the same issue.  I believe there are some major firmware bugs with this router.  First of all I set up everything using the web interface.  My laptops could connect to the network and internet but any of my devices that use wireless bridges (WET610N) to connect could only get local network access.  They could not connect to the internet.  After some troubleshooting I found the reason it was not working properly.  I used DHCP reservations in my network because of port forwarding and such.  Well when the devices connected to the bridges were in the reservation list they were unable to connect to the internet.  After I removed them they now are able to get on the internet without a problem.  So that is the first problem I've found so far...
 
The second is I can no longer connect from my Xbox 360 to my Media Center PC.  I tried to set up a new connection but this did not work either.

View 9 Replies View Related

Linksys Wireless Router :: E4200 - It Keeps Dropping Internet Connection

Jan 15, 2012

ever since i had a power failure losing all power in my apartment, my router has begun regularily losing connection to the internet, I have to go into the router and renew ip address which is quite annoying

[code]....

View 6 Replies View Related

Linksys Wireless Router :: Cannot Get Internet Connection With E4200 V2 In 5Ghz

Jan 28, 2012

I setup my E4200 v2 with different SSID's for 2.4 and 5GHz modes. I have no problem with a 2.4 Ghz connection on my laptop, but I cannot connect to the internet in 5GHz. mode. I choose the 5 GHz SSID and enter the passphrase but no luck, even though I have a full 4 bars inthe wireless icon. 

View 4 Replies View Related

Linksys Wireless Router :: E4200 2.0.37 - Internet Connection Dropping

Jun 10, 2012

my e4200 wireless. I have internet connection speed of 40mb and I have epc 3925 working in bridged mode as modem and E4200 as router. When I connect my laptop with wire on e4200 I am getting 37-38 Mbps on speedtest.net which is perfectly fine. But on wireless I am having a lot of dropping of speed: I have 2mps then jumping to 5-6 Mbps and so on it never goes more than 5-6 Mbps. When I disable WMM Support in QoS I am having perfectly constant 20mbps but... I have only g network 54mbps. [code]

View 9 Replies View Related

Linksys Wireless Router :: E4200 Internet Access Status Ok In Router

Nov 4, 2011

I am trying to setup my E4200 to my new Cable Modem. I followed all of the procedures. I get Internet access when plugged directly to modem. I cloned the MAC Address and the Stus of the Router displays my current IP's (so I should have Internet). However, when I plug my computer into the Router I get no internet access.

View 3 Replies View Related

Linksys Wireless Router :: E4200 - Media Server / Router Access Loss Internet OK

Feb 20, 2012

I have a problem with the e4200 router and a mybook 1 TB connected to it. The media server works fine but after a while i loose contact with the router and the server this means that the Cisco connect doesn't work, the 192.168.1.1 doesn't work and I can't find the disk via \. I do have internet connection via wifi as im using it now....why I loose connection to the router? The lease time is 24h and it can happen more than once in a day.

View 4 Replies View Related

Linksys Wireless Router :: EA3500 USB Not Allowing External Hard Drives?

Jun 12, 2012

Similar to this issue with the EA4500 - I have the same issue with maping the drives from both PC and Mac - the USB drive is recognized, admin/user names are coreated appropriately, the folder structure is imported into the admin control..similar issue with EA4500 user here

View 3 Replies View Related

Linksys Wireless Router :: EA4500 USB Not Allowing External HD Only Flash Drives?

Apr 16, 2012

Recently purchased an EA4500 router and it is connected to the Internet.  One of the reasons we purchased this router was to take advantage of the usb port (only 2.0 unfortunately) to be able to share media across the network.  I spent over two hours on the phone (4/16/2012) with Linksys Tech support trying to get this feature to work.  When using a little flashdrive I can easily find the connected usb device.  However, when trying to connect to an external hard drive, it will not connect.  I tried three different external hard drives, a Western Digital 500 GB Elements drive, a Western Digital 2 TB My Book Elements drive and even a portable 1.5 TB Seagate FreeAgent drive.  Every drive had the same result.  In fact after plugging each one into the EA4500 and then selecting Safely Eject and then plugging them into my computer, each one had to go through the Fix process in order to work again.  I tried this several times.  Linksys Tech Support could not get it to work either, and they even used remote access.  When going into the web interface of the EA4500, the router sees the external drives attached to it.  However, only the little 16GB flash drive can be seen by the computer.  I know there is a list for approved devices that work with a different device, the E4200 [URL]
 
It looks like my devices are there but nonetheless its not working.  Really not sure why the router can see all of the devices but only the computer can see the flash drive.

View 9 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved