Linksys Wireless Router :: E2000 Not Allowing Access To Other Devices
Nov 5, 2011
I just set up my e2000 on a PC using Windows 7. I am additionally trying to set up additional devices on the network. The two that I am currently working with are:Dell Latitude d240 running Windows XP.HTC Evo smartphone running Android
I can't get these on the network through the e2000. They can access the internet through the e2000 but only as a guest and therefore don't have the same level of security. What do I need to do to successfully put the above devices on the network?
View 2 Replies
ADVERTISEMENT
Oct 18, 2010
How can I tell the names of the devices that are connected to my E2000 router? Cisco connect says I have 4 devices connected but I only have 3. I am trying to figure out where the 4th device is coming from.
View 9 Replies
View Related
Mar 1, 2013
I have a cisco router model number E2000 it has worked fine until a few days ago, it keeps losing its signal on all my wireless devices I have reset it and it still is not working properly. I am wondering if I have to many wireless devices running through this router.
View 1 Replies
View Related
Jan 1, 2013
I have set up access restriction times for my son (we have wireless access for all systems). I use the MAC address on his systems. Xbox, Kindle Fire and his Laptop. The MAC address are Correct. Here is the problem:
I set the "allow" and times from 6pm - 11:00 pm (while on xmas vacation) - the system works for a while he is shut off as i would like but....
After a period of time the entire house goes off line. I have to reboot the power on e2000 router and then disable the access restrictions. System then works. Problem is repeatable. What is the deal. I have updated firmware already. Otherwise the system works great. Never dies. Just when i set access restricions for a SPECIFIC time it kills entiore houese. BTW i can deny him outright 24/7 and the system idsables his access fine. Its just when i set specific times
View 3 Replies
View Related
Apr 21, 2013
I have a Linksys E2000.
It worked fine until one day, without any change at all, it simply stoped working. I mean, I can still connect through my wifi laptop connection (it shows connected to my router and says that I have an excelent signal). But, I can't reach the internet. But, If I unplug the internet cable, and plug it in my laptop, the connection works fine. A friend told me that this could be caused intentionally by the internet provider, that they would block my signal to avoid me using a wireless router, trying to force consumers to sign their own wireless service. Thus, by this friend advice, I've cloned my laptop's MAC address to the router. It didn't work either.
View 4 Replies
View Related
Nov 12, 2011
I got a refurbished E2000 on Amazon. Last night I set it up and when I tried accessing this website [URL], I could not connect to the server. First I thought it's the server problem and let it go. This morning it's the same probelm. I called my local cable technician and he told me it's the wifi router is blocking the website. I called the CISCO guys and they refused as it was out of warranty.
View 2 Replies
View Related
Aug 21, 2011
I can connect to my router but either way it seems like i can't get any internet access (both wireless and by cable): url...I have tried the steps that the linksys FAQ suggests shall fix this problem, but this has not worked. I have also tried to reset the router without any luck. I know it its not the modem that is causing the problem because I'm wired to it now.On the E2000 every light is blinking as it should be (hence the FAQ) so it indicates that there might be a problem with the connection between the router and the computer (tested on other computers too without success).
View 9 Replies
View Related
May 12, 2012
Just a day or two ago I was able to do what the title says, didn't make any adjustments to my E2000 while in it, had to find something though.Anyhow, connecting to http://192.168.1.1 results in "Unable to Connect", etc. Also tried it in IE9, Firefox Beta is my primary, and it still didn't work. Tried using Cisco Connect and it says it cannot connect to my router. I am wired to my E2000, which in turn is wired to my DSL modem (Actiontec GT701D-Its firewall not in use). I sitll have full connection to the internet as well as other wireless deveices do in my house.
View 1 Replies
View Related
Feb 12, 2013
How do I reenable guest access on my e2000 without having cisco connect installed?
View 1 Replies
View Related
Aug 3, 2011
We have a wireless network and would like to extend the range for it and I was told that a E2000 could be setup to extend the range.If we say that our existing wireless network has the SSID network1, can the E2000 be setup so that it is connected to a LAN socket and then wok as a wireless runter with the same SSID (network1) so that pc's can connect easily ?Or must the two wireless routers be connected with a dedicated cable ?Or must I setup the new E2000 up as a new wireless network with a new SSID like network2 ?
View 3 Replies
View Related
Mar 12, 2012
E2000 about a years old.One of the rule is to block internet access from 1am to 4am for certain internal IPs.Working fine until a week ago. Once the time kick in, the E2000 will not route any internet access for any internal IP until the unit is power off and power on reboot.If that rule is disabled. then the E2000 will route all days and nights with no problem.Updated firmware to 1.0.0.4 already.I replaced the WRT45 because of the same problem a year ago. Now just about a year, this E2000 keeps blocking all traffic.
View 1 Replies
View Related
Sep 8, 2011
when I switch my e2000 wireless setting to 5 ghz the wireless devices don't work
View 2 Replies
View Related
Feb 26, 2012
I use a E2000 as a wireless access point to the Internet, by connecting the LAN of the E2000 (set for x.x.x.5) to the LAN of an RVS4000 (Set for x.x.x.1). The E2000 is set for Automatic Configuration, and everything works fine..... Until a power failure occurs... Then, after everything boots up again.. I get the "NO INTERNET" prompt on the wireless....
By using Ping Plotter, from a computer on wireless end, and another computer with Ping Plotter on the wired side of the x.x.x.1 LAN, I've determined that it's the E2000 that has disconnected from the RVS4000.
I have found a work-around, though....No matter How the setting boots up, If I toggle away from and then BACK TO: NAT DISABLED in Advanced Routing, Everything is back operational..... Until the next Power Failure....
Is there any way of making this Automatic.
In another forum, there was a suggestion of putting the E2000 in Bridge mode in WAN settings... I can't find it....
View 3 Replies
View Related
May 28, 2011
I just purchased 2 E2000 routers at BB and was assured the second one could be configured as a repeater access point. Some current messages indicate this is not possible.Will a Cisco moderator please confirm and clarify repeater options.
View 2 Replies
View Related
Dec 6, 2012
we got a At&T Modem/Router upstairs, and then we got a long ethernet cable running from there to the basement. The problem is that this only allows for one LAN connection at a time (an issue for LAN parties and such). I do have an E2000 Linksys router however and I want to be able to use that as like a switch/access point.I am pretty sure this is possible but I have forgotten all of the steps to do it.The att modem/router is running on 192.168.1.254, and my Linksys which is now directly connected is on 192.168.1.1, so I have a different address in that regards.Do I need to edit my Linksys settings now, or do I have to edit the at&t settings?Also I will be using this for Xbox Live at points so will I need to re-open all those ports up on my Linksys, or at least set the DHCP to the Xbox's static IP to keep my NAT good?
View 2 Replies
View Related
Jul 31, 2011
I have an E2000 router with the most current firmware. I have a Sony VAio laptop with Windows 7 Home Premium 64bit,a Macbook with 10.6.8, and a new Asus Transformer Prime with ICS.My work desktop is a Dell Optiplex 380 with Windows 7 Pro 32bit. I frequently work from home and have no issues remoting into to my work PC from by Sony laptop via VPN and RDP.However I have never been able to connect successfully to my work PC with my Macbook(using Remote Desktop Connection 2.1 for Mac OS) or Asus tablet(using WYSE Pocket Cloud RDP app for Android). I can however connect to the VPN itself on the Macbook and tablet without issue same as my Windows laptop. The other interesting part is I can connect via RDP when I am connected to a Mi-Fi 3g hotspot. So it is definitely something in the my Linksys E2000 blocking the connection for some reason. I have even set Port forwarding of 3389 with the ip's of both the Macbook and Asus tablet.I have also tried connecting via ethernet to the router with the same outcome. I cannot ping my work pc from either device as well.In addition the firewall on my work PC is completely disabled and all services related to Remote desktop access are enabled and running.
View 3 Replies
View Related
Jun 10, 2011
I've got a Linksys E2000 router and a Brother MFC-7840W wireless printer and they don't seem to want to play nice together. The set-up process was fine and I can usually print wireless without a problem, but every so often I'll try to print and my computer will say that the printer is offline. Other computers on my network also show it as offline. The printer confirms it has an IP address, but even after power cycling it won't be picked up by my machines. I've even tried a full reset of the printer and re-configured it, at which point it is able to successfully obtain an IP address, but it still shows as offline on my PCs.
The only solution I have found is to powercycle the router. This always works. Now that's not a terribly inconvenient workaround most of the time, so I've been doing that for a few months now. It obviously implicates the router as the point of failure, but wireless internet access is not affected when the printer appears to be offline, so obviously some packets are getting through normally.
View 3 Replies
View Related
Mar 13, 2012
How can i use Linksys E2000 rounter as a Access point ?
View 1 Replies
View Related
Jan 17, 2013
I have an EA 2700 installed using a wired network. It is just one desktop computer and a VOIP box shared by my internet connection. I am quite new at wireless connectivity.I would like to add wireless devices, specifically a phone and a laptop, but I do not want ANY of the wireless devices to be able to access and make changes to the ROUTER or any other computers on the network. I do need to keep the network secure.How do I set the router and/or devices up to accomplish this?
View 9 Replies
View Related
Nov 3, 2012
My Netgear wireless router had been working just fine and then inexplicably stopped allowing wireless internet access. My modem is fine. I contacted my internet service provider, and no luck. I unplugged the router's power source and plugged it back it in. Still not working. I switched the power on and off. Nothing. I do not know what to try next.
View 1 Replies
View Related
Dec 25, 2011
My PC will connect just fine, but it is the only device on my network that the router will allow internet access. The router will allow other devices (DVR, laptop, nook) to connect to it, but won't allow those devices to connect to the internet. Each device will show the same error, - "connected to linksys - no internet". I've reset the router many times with no results.
View 1 Replies
View Related
Aug 19, 2012
I just switched to the EA4500 Router and I'm now unable to remotely access my camera devices. I have done the port forward. I can access the cameras from my local LAN both when using the local 10. ..and external 99 .. Addresses. When I go off the local connection - Access does not work. Slingbox did its auto configuration and I can access it. I just cant get to camera devices (Panosonic, Foscam, etc.).
View 3 Replies
View Related
Oct 22, 2011
I have a WRT54g with Tomato firmware. I am trying to set up a WAP54g to extend the range but while that access point does show up as a network, nothing can connect to it. I already have the router's MAC address put in the WAP. I think the problem is that I have Tomato on the router and that conflicts with the default firmware on the WAP. Range isn't really the problem, I just need to strengthen the signal in a specific area that it's not getting to because of walls. I can't even switch to previous versions of Tomato anymore. I may have just bricked it.Some facts about my setup-My modem has default settings: PPPoE connection with a DHCP server enabled.-I set the router to use DHCP and put it in "Access Point" mode.
-The WAP is set to repeater mode and it was set to Static IP configuration by default. I simply followed the instructsions here: url....
-There are three different MAC addresses: The WAN, LAN/router, and the Wireless. I put the Wireless MAC address in the access point. Is that correct?
-My desktop is wired directly to the router and it has a static IP outside the router DHCP's IP range-UPnP is enabled by default in the modem and router, but I'd like to try to get this working rather than buy all new equipment.
View 7 Replies
View Related
Jul 8, 2012
I am running an E3000 with Firmware - 1.0.04.
I would like to schedule my boys ipods to be on the network from 2:00pm to 4:00pm each day.
Running the Cisco connect software it would appear I can schedule from 2pm until the next morning but not a 2 hour window in the same afternoon.
Looking through other posts I see earlier software where this can maintained through the Router firmware but with 1.0.04 I seem to have to use Cisco Connect.
So how can this be done with my current configuration ?
View 3 Replies
View Related
Nov 25, 2012
I am running the e3000 as an access point.. My iphone and ipad connect to it seamlessly. After a few hours to days, they are no longer recognized by the router. Nothing I reset on the phone or ipad makes any difference. The only solution I have found is to re-boot the router. They then re-connect on their own.
View 4 Replies
View Related
Aug 31, 2012
Where can I find a log or list of devices that attempted to access my EA4500 wireless network?I am using the cloud services to monitor my EA4500 usage in an apartment environment.
View 1 Replies
View Related
Aug 15, 2011
I have installed my new E4200 and it works beautifully. I have several wirelss adapters and a few wired connections through powerline adapters. I also have a second VPN router attached to the 4200.I can see the wireless connected devices with the associated IP addresses. If I plug a laptop directly into the Cisco, I can of course see it.However, I can see none of the devices attatched to the powerline devices? I have a securty cam connected via the powerline and want to know the IP address. I checked with cisco technical support via chat and they said it is impossible. I have used 2 previous routers with the same configuration and can see all devices.
View 1 Replies
View Related
Nov 16, 2010
I'm not able to logon to WRT54GH-SG over 192.168.1.1. I'm using correct password & have NOT forgotten. I'm hitting 401 page. The support rep told me reset the router which I do not want to before I explore any possibilities.
View 8 Replies
View Related
May 18, 2011
Abruptly internet access disappeared. It's a router issue, none of the computers here can connect. Further, I can't access the router through a browser - 192.168.0.1 results in a "Firefox cannot connect" message. I've tried resetting the DNS to no avail. I'm typing via cell phone and it's annoying, but I'm willing to try about anything.
View 4 Replies
View Related
Oct 16, 2011
I have a 100mb conection and regularly get 90mb plus speed when conected direct to the modem. If I conect via the E4200 I only get 50mb ? I have tried disabling the firewall and QOS but this has had no effect. I am using a wired conection and the latest firmware. Its almost as the E4200 is capped at 50mb throughput.
View 6 Replies
View Related
Jun 12, 2012
Similar to this issue with the EA4500 - I have the same issue with maping the drives from both PC and Mac - the USB drive is recognized, admin/user names are coreated appropriately, the folder structure is imported into the admin control..similar issue with EA4500 user here
View 3 Replies
View Related
Apr 16, 2012
Recently purchased an EA4500 router and it is connected to the Internet. One of the reasons we purchased this router was to take advantage of the usb port (only 2.0 unfortunately) to be able to share media across the network. I spent over two hours on the phone (4/16/2012) with Linksys Tech support trying to get this feature to work. When using a little flashdrive I can easily find the connected usb device. However, when trying to connect to an external hard drive, it will not connect. I tried three different external hard drives, a Western Digital 500 GB Elements drive, a Western Digital 2 TB My Book Elements drive and even a portable 1.5 TB Seagate FreeAgent drive. Every drive had the same result. In fact after plugging each one into the EA4500 and then selecting Safely Eject and then plugging them into my computer, each one had to go through the Fix process in order to work again. I tried this several times. Linksys Tech Support could not get it to work either, and they even used remote access. When going into the web interface of the EA4500, the router sees the external drives attached to it. However, only the little 16GB flash drive can be seen by the computer. I know there is a list for approved devices that work with a different device, the E4200 [URL]
It looks like my devices are there but nonetheless its not working. Really not sure why the router can see all of the devices but only the computer can see the flash drive.
View 9 Replies
View Related
Mar 7, 2012
I am trying to allow PPTP traffic through my Linksys WRT320n to a PPTP VPN server on my home network.The Linksys WRT320n is running firmware 1.0.05 build 002Mar 31, 2011.I have created a Port Forwarding rule on the Linksys to allow TCP & UDP port 1723 through to my internal IP of the PPTP VPN server,but everytime I try to connect with a PPTP client from outside of my network I get a connection error on the client.Checking the PPTP VPN servers logs I see the following errors (Please note all IP's have been masked) Mar 2 11:15:07 ap-01 pptpd[5300]: CTRL: Client x.x.x.x control connection startedMar 2 11:15:07 ap-01 pptpd[5300]: CTRL: Starting call (launching pppd, opening GRE)Mar 2 11:15:07 ap-01 pppd[5301]: pppd 2.4.4 started by root, uid 0Mar 2 11:15:37 ap-01 pppd[5301]: Exit.Mar 2 11:15:37 ap-01 pptpd[5300]: GRE: read(fd=8,buffer=41fe30,len=8196) from PTY failed: status = -1 error = Input/output error, usually caused by unexpected termination of pppd, check option syntax and pppd logsMar 2 11:15:37 ap-01 pptpd[5300]: CTRL: PTY read or GRE write failed (pty,gre)=(8,9)Mar 2 11:15:37 ap-01 pptpd[5300]: CTRL: Reaping child PPP[5301]Mar 2 11:15:37 ap-01 pptpd[5300]: CTRL: Client x.x.x.x control connection finished
From looking at the above errors, it seems as if the Linksys isn't forwarding GRE through to my PPTP server.I have tried various settings, including enabling and disabling the PPTP Passthrough option on the Linksysbut still can't get PPTP to work.What is the correct way to get GRE traffic forwarded through the Linksys?
View 4 Replies
View Related
