I have a cisco router model number E2000 it has worked fine until a few days ago, it keeps losing its signal on all my wireless devices I have reset it and it still is not working properly. I am wondering if I have to many wireless devices running through this router.
View 1 RepliesE2000-RM router has been working fine until about 2 days ago. Wired connection still works fine, but the wireless signals seems to be dropping in and out. I have a couple wireless devices and they all seem to be experiencing problems. Using the network connection bar on my laptop sometimes it shows a strong signal and connects no problem. Then all of a sudden the signal is gone (drops off list). It can be both the main and guest signal dropping, other times it might just be the main, etc., etc. Sometimes it shows a signal but will not connect and then a few seconds it might connect, or drop entirely. I guess the best word to describe it is highly erratic. Distance does not seem to matter. I can be 2 feet away and get the same behavior. The indicator on the box shows a signal at all times.
View 8 Replies View RelatedI've had been successfully using a WRT400N to extend my wireless network as follows:
The WRT400N connected to my network via an Ethernet port in my kitchen. The cable ran down to a corner of my basement connecting to Verizon router that brings in our Internet, TV etc.
The Verizon router's poor location was a problem, and placing the WRT400N in the kitchen worked perfectly, providing excellent network access and Internet to wireless devices throughout my home. It worked fine for over a year.
Recently, we had a power outage which reset the WRT400N to factory settings. and I am having trouble getting it to work again. I set it up in the first place, but am now having difficulties. Clearly, I am no guru!
I tried to get it going again by: 1) plugging the WRT400N into a PC and giving it a new IP address that would not conflict with the Verizon router (both default to 192.168.1.1) 2) turning off DHCP, 3) renaming the router, 4) changing the router password, 5) setting up a WPA2 security key.
I then plugged the WRT400N back into the kitchen Ethernet port, but something is wrong. Wireless devices cannot find the WRT400N.
The good news is that I can "see" the WRT400N through any PC on the network via a browser and access setup, but the bad news is that devices cannot see or connect to the wireless signal.
When I go to "Status" it shows the IP address, subnet address and default gateway all at 0.0.0.0. On the SETUP page, it has the correct router address (192.168.1.9), and a subnet mask of 255.255.255.0. Not sure if it is supposed to be this way...
How can I tell the names of the devices that are connected to my E2000 router? Cisco connect says I have 4 devices connected but I only have 3. I am trying to figure out where the 4th device is coming from.
View 9 Replies View RelatedI just set up my e2000 on a PC using Windows 7. I am additionally trying to set up additional devices on the network. The two that I am currently working with are:Dell Latitude d240 running Windows XP.HTC Evo smartphone running Android
I can't get these on the network through the e2000. They can access the internet through the e2000 but only as a guest and therefore don't have the same level of security. What do I need to do to successfully put the above devices on the network?
when I switch my e2000 wireless setting to 5 ghz the wireless devices don't work
View 2 Replies View RelatedI have an RV110, and I'm interested in extending the WiFi range using its WDS feature.The RV110W data sheet simply states.. "allows wireless signals to be repeated by up to 3 compatible devices",Where can I find these "compatible devices", and has anyone had any success using WDS with any APs from the SMB product line?
View 6 Replies View RelatedMy Dlink router has been working fine until recently. The only changes I made was to try to put time limits on my kids' devices, through Tools->Schedules and Advanced-> access control. Things worked Ok, but I soon realized I had to reserve each kids' device DHCP number, or so I thought(?) Anyhow, now I seem to have to log into my dlink router weekly as their wireless connection stops each week. Not sure if it affects the non-reserved wireless devices. Not sure what's happening or what I did wrong. Running the following: DIR615 hardware Version B2 Firmware 2.25 Under DHCP Server settings: Enable DHCP server - checked Addrss range 192.168.0.100 to 192.169.0.199 Note - reserved ips in that range Lease time 1440 minutes Always broadcast - checked rest blank NetBIOS type Mixed mode.
View 1 Replies View RelatedI have installed my new E4200 and it works beautifully. I have several wirelss adapters and a few wired connections through powerline adapters. I also have a second VPN router attached to the 4200.I can see the wireless connected devices with the associated IP addresses. If I plug a laptop directly into the Cisco, I can of course see it.However, I can see none of the devices attatched to the powerline devices? I have a securty cam connected via the powerline and want to know the IP address. I checked with cisco technical support via chat and they said it is impossible. I have used 2 previous routers with the same configuration and can see all devices.
View 1 Replies View RelatedIt seems since I have moved into my new house months ago my E3000 keeps on dropping its signal. I have an older roouter that doesn't do this. Currently I have a PS3/Xbox 360 plugged in and then the 3 laptops that use the wireless.
View 1 Replies View RelatedSo I just got this router in hopes that I would get a better signal within my room as opposed to my older router. Unfortunately, nothing has changed, in fact I think I'm getting weaker signals. My previous router was a D-Link WBR-2310. I went to speed test.net and tested 3 variables. My wifi on my desktop in my room, my wifi when right next to a router on my laptop, and my wifi using my neighbors wifi in my room.
My room Desktop Wifi:
Download was 0.50 mbs Upload: 3.6
My laptop right next to Router:
Download 19.87 mbs Upload: 3.5
My room Desktop Neighbors Wifi:
Download was 17.3 mbs Upload was 3.32.
What is the point of this new wireless N router, when it can't beat a G router older model in reach? And why does is have a 0.50 mb d/l speed but a 3.6 upload speed?
I have a Linksys wireless-G connected to my main computer and modem. We live in an extremely long house and I am attempting to connect a Belkin wireless-G router so that the signal is stronger on the other side of the house.
View 1 Replies View RelatedI am having no end of issues with this router since the upgrade to CCC. I don't want to downgrade because the reason I purchased the router was for the hopeful addition of more apps later on and the CCC.
My router has now suddenly decided to no longer broadcast N signals. My 2.4ghz network is set for mixed and my 5ghz is set for N Only. They are both set to auto channel and WPA2 Personal security and have been working since I purchased the router on Sunday.
Last night it spontaneously rebooted and that was that.
Both laptops (with N adapters) are seeing the 2.4ghz network as 802.11g and my 300Mbps notebook adapter is seeing the 5ghz network as 802.11a. InSSIDer is showing that both networks are now broadcasting at a max of 54Mbps.
I have tried rebooting the router multiple times. I have also tried unplugging it for 60 seconds. I have also attempted to force the 2.4ghz to 20Mhz and a more optimal (unused) channel. That doesn't work. I tried setting the 5ghz network to wide (40mhz) with an optimal channel. Same deal. Still seeing it as 802.11a.
I just installed a Linksys WRT160N router. The signal started of good about 50 to 70 feet from the routers location. Now the signal is registering as low to good, about 54Mbps. I was wondering what options I might have to install a wireless bridge for expansion of the signal. I have configured an encrypted network using WPA2. I am wondering what the technical difficulty would be to install and configure it. I setup the WRT160N myself if that means anything.
View 4 Replies View RelatedAt one of our offices, we have a Cisco ASA5505 firewall that has dhcp enabled. I have a WRT54G router plugged into that firewall with DHCP enabled. The scope of our inside network is 192.168.51.***, however when connected to the WRT54G, it gives you the scope of 192.168.1.***We have an antenna amplifier screwed into one of the antenna ports on the router. This whole setup works fine.
The problem is we need to install an access point WAP54G in a building across the property (picks up router wireless signal fine) to repeat the wireless signal to the back of the property where the router will not reach. I have read that all you need to do is type in the wireless mac address of the routher into the access point and select "Wireless Repeater". I have the channels set to 6 on both devices as well as the same security configuration. When I try to connect to the wireless network on the access point, It never gives me an ip in the 192.168.1.*** scope, which the WRT54G is configured to give out. Also, in this setup does the WRT54G need to be set to router or gateway mode? I do not need it to distribute ip addresses. [code]
I bought a WRT54G v6 and since I installed and configured it I've experiencing an intermittent connection in my lan where you can find a notebook wireless connected to the router and a desktop wired to the router by cable.I'm working and then the network stops, both computers lose signal with the router. The signal come back few seconds later but to work in internet again I have to wait some minutes.So I contacted the live assistent on Linksys web-site and the agents said to me to do something that I will list here:- lower the MTU to 1480, 1470, 1450- updated the firmware- reflash the firmware- reset the router for about 30 seconds- do the power cycleIf you don't know what update and reflash the firmware or do the power cycle means you can srsistedthe conclusion is that ee the instructions on this pages: [URL] ...
View 9 Replies View RelatedI have a WLC 4404. I added a new AP to the network and it is associated with the WLC now. But still its not braodcasting the ssids. I compared the configuration with the ones installed before and configuration is same.
View 9 Replies View RelatedI have a Wrt160n router and a Motorola sb120 modem (provided by comcast after my original modem got fried by lightning, no I didn't have my router hooked up when that happened), I have been having trouble trying to get the modem to send the internet signal to my router. I have tried mac address clone that was suggested on this forum for someone with a different router but still no internet to my computer, its all hooked up through Ethernet cables, the computer I have it hooked up with a hard line is running windows seven. When I plug the modem straight to the computer it works and I have internet but when I hook up the router between them it has no internet.
View 9 Replies View RelatedJust got the E4200 and it seemed great at first. Connected at 450mbps at close range (maybe 6ft away) and got 223mbps transfer.It seems that recently my signal is much weaker. I'm around 6-8ft away from the router and I'm getting between 270-360mbps, which to me is poor given the short range.InSSIDer says the RSSI is -50, while my other wireless N router (dual band) is -35 and is in the exact same location. I'm using the 5ghz radio only, and it is set to N, and I'm using channels 44 and 48. I checked the hidden advanced wireless page and transmit power is already set to high.My laptop has an Intel 6300 wireless card.I'm using the current firmware 1.0.02,I've noticed that the speed of the router randomly seems to drop off too (just as I type this, the link rate has gone back up to 450mbps... typical). Is the router throttling when it gets hot or something? So I just want to find out if others are experiencing similar rates at the same kind of distance. Seriously, how can you advertise something as 450mbps when you can't even get that link rate at a distance as short as 6ft?I can't see any thing I can do to increase the link speed (back down to 270mbps now), short of a firmware update to increase the power and use higher channels. I hear the higher channels are much better, so who do I have to write to, to plead for new firmware?,This is a great product, but it's totally ruined by stupid internal antennas and a weak transmit power.
View 1 Replies View RelatedI live in a single story bungalow, and im wanting to resite my EA4200 up into the roof space, just wondering which is the best position to mount it in for signal, horizontal or vertical, or doesnt it matter ?
View 1 Replies View RelatedSo here's my issue, I just bought this EA4500 so I could use the 5.0 Ghz and get a new 2.4Ghz as my old Netgear would drop the signal on a fairly regular basis. I've set the channel on 2.4 to 1, 20 Mhz Channel, and my neighbors are for the most part using channels 6 and 11 (one guy is using channel 2 at 40Mhz but has a very low signal strength). The signal drops out sometimes as often as every 5 minutes, and now it is doing it on my new router. Here's the kicker, the 2.4 band falls out from my router and some of my neighbor's routers, no new signal seems to come up, but the 5.0 band on the EA4500 is just fine, as is the wired route. Is the 2.4 band just being assaulted at my home and I'll have to deal with it, or is it that my new router, old router, and my neighbor's routers, all suck, and we should all get refunds? Any solutions to troubleshoot this beyond running a netstumbler like software, setting hard channels (including width), and long hours of trial and error? I am running this all from my macbook air, the 5.0Ghz is at 40Mhz, is the only signal, and is on a fixed channel.
View 7 Replies View RelatedI can connect to my router but either way it seems like i can't get any internet access (both wireless and by cable): url...I have tried the steps that the linksys FAQ suggests shall fix this problem, but this has not worked. I have also tried to reset the router without any luck. I know it its not the modem that is causing the problem because I'm wired to it now.On the E2000 every light is blinking as it should be (hence the FAQ) so it indicates that there might be a problem with the connection between the router and the computer (tested on other computers too without success).
View 9 Replies View Relatedlinksys router problems Linksys wireless router connected to cable modem. over time router looses connection to internet. rebooting router reestablishes connection. running XP sp3 from laptop connected wirelessly?
View 3 Replies View RelatedDlink Dir-657 keeps losing internet connection on wifi devices only . the connection remains to the router but no internet .if I disconnect the connection i am unable to reconnect to the router until i reboot it. My internet remains on my network cabled devices .I am running on an empty channel 3 , usually happens 20 to 60 minutes after the router is up . Dlink sent me a replacement refurbished one and this one is doing the same thing . I owned the original one for about 5 months with no problems at all ,no new electronics in the house and have not changed the placement of the router .
View 4 Replies View RelatedI would like to set the router's dns entries but I don't see how to do that. Basic setup page has DNS setep for the DHCP scope but I don't want to push dns to my pc's. What I am looking to do is to use an alternate dns to what my service provder pushes and still have the abliity to route on my internal network.
View 1 Replies View RelatedWe bought our Linksys E2000 in the summer and went to set it up but something came up... Now we are trying to set it up but cannot find our WPA key... Where can we find this?
View 2 Replies View RelatedSo i can only forward 10 ports on my E2000.Example, one game (Battlefield 3) requires 10 ports (TCP and UDP combined).What about my other games? how can one, if possible, add more ports to the router?
View 4 Replies View RelatedE2000. I run the setup program, my laptop sees the router and it shows a strong signal. When I try to connect with it, it won't connect.
View 9 Replies View RelatedI've been looking around like a madman now in the settings. where can I turn off my WPS ? Just cracked my own PIN within 6 hours with Reaver.
View 9 Replies View RelatedMy internet cut out last week and after calling my ISP I found out it was in fact my router that was causing the problem (regular connection to PPOE works fine). I've only had my E2000 about 2-3 months and have not had any problems with it. I've restarted the router, done a factory reset, upgraded the firmware, renewed the IP and still I cannot get any connectivity. I can access the router UI fine and I get a response from pinging it and also I have tried replacing the cables but that didn't fix the problem either.
View 9 Replies View RelatedI have an E2000 that I was given as a gift. I would like to use at it my office for a switch at my cubicle where I can connect 2-3 computers simultaneously. I am in a large network and am a user only. When I hooked the E2000 up today my computers would not get internet access BUT my laptop got wireless access and internet.
View 2 Replies View RelatedI'm using E2000 currently and meet a wireless connection problem. The speed can up to 300M bps. When I confiured the E2000 to band auto (20-40mhz) and my wireless network card to work at also auto (20-40) mode, it always down to 144M speed when connection.
If I changed some settings in E2000's wireless configuration, in the status sheet I can see it works at 40MHZ. But after a while,(5-10 mins) it automaticly down to 20MHZ and my labtop connect only got a 144M speed.
how can I deal with that to make it always keep at 300M connection? Note the previous router I used to connect to my lattop can always keep that speed.
My router keeps going out, and the only thing that gets me back on is to unplug, replug, then I'm good but only for about 20 minutes.
View 2 Replies View Related