It seems since I have moved into my new house months ago my E3000 keeps on dropping its signal. I have an older roouter that doesn't do this. Currently I have a PS3/Xbox 360 plugged in and then the 3 laptops that use the wireless.
View 1 RepliesE2000-RM router has been working fine until about 2 days ago. Wired connection still works fine, but the wireless signals seems to be dropping in and out. I have a couple wireless devices and they all seem to be experiencing problems. Using the network connection bar on my laptop sometimes it shows a strong signal and connects no problem. Then all of a sudden the signal is gone (drops off list). It can be both the main and guest signal dropping, other times it might just be the main, etc., etc. Sometimes it shows a signal but will not connect and then a few seconds it might connect, or drop entirely. I guess the best word to describe it is highly erratic. Distance does not seem to matter. I can be 2 feet away and get the same behavior. The indicator on the box shows a signal at all times.
View 8 Replies View RelatedMy E3000 has about 60% packet loss if the channel selected is anything other than 1. I can't enable 5GHz or even 40mhz 2.4GHz channels without dropping 60% packets.
View 9 Replies View RelatedSet channel manually - i've tried all the channels no luck
Different SSIDs for 5g and 2.4g
Beacon Interval 50
Fragmentation threshold 2306
RTS Threshold 2304
I'm running firmware 1.0.04 build 6 <script type="text/javascript"></script> Dec 6, 2010?I've had the router for 4 months now and this has been happening for the last 3.
I have Comcast cable internet routed through a linksys E3000 router. My desktop is connected to my router via ethernet and my various other devices including my laptop are wifi connected. It seems almost at random that my desktop will lose its connection.Windows will show me as still being connected and my network connection will show a normal status until I atttempt to repair it then it will change to limited or no connectivity. Through all of this, my other devices all still have a wifi signal (I don't use more than 1 or 2 at the same time). I can reconnect to the internet by unplugging my ethernet cable then reuplugging it back in and my connection will start working again. I've also had several blue screens, and when I checked the dmp files it revealed my network card driver as the culprit, yet I have reinstalled and even clean installed the microsoft signed driver. I have also attempted to reboot both my modem and router to no avail.
Microsoft XP
Marvell Yukon ethernet adapter on a biostar mobo
C:Documents and SettingsMain>ipconfig/all
Windows IP Configuration
Host Name . . . . . . . . . . . . : sn1
Primary Dns Suffix . . . . . . . :
[code]...
I had an old belkin router and the net worked fine well the router would need to be restarted every week or so. But i got an upgrade and i now have a TP link TD-W8961ND The net is terrible its either there or not. have to keep refreshing pages ect .Could a setting possibly be wrong?
View 1 Replies View RelatedSo I just got this router in hopes that I would get a better signal within my room as opposed to my older router. Unfortunately, nothing has changed, in fact I think I'm getting weaker signals. My previous router was a D-Link WBR-2310. I went to speed test.net and tested 3 variables. My wifi on my desktop in my room, my wifi when right next to a router on my laptop, and my wifi using my neighbors wifi in my room.
My room Desktop Wifi:
Download was 0.50 mbs Upload: 3.6
My laptop right next to Router:
Download 19.87 mbs Upload: 3.5
My room Desktop Neighbors Wifi:
Download was 17.3 mbs Upload was 3.32.
What is the point of this new wireless N router, when it can't beat a G router older model in reach? And why does is have a 0.50 mb d/l speed but a 3.6 upload speed?
I have a Linksys wireless-G connected to my main computer and modem. We live in an extremely long house and I am attempting to connect a Belkin wireless-G router so that the signal is stronger on the other side of the house.
View 1 Replies View RelatedI am having no end of issues with this router since the upgrade to CCC. I don't want to downgrade because the reason I purchased the router was for the hopeful addition of more apps later on and the CCC.
My router has now suddenly decided to no longer broadcast N signals. My 2.4ghz network is set for mixed and my 5ghz is set for N Only. They are both set to auto channel and WPA2 Personal security and have been working since I purchased the router on Sunday.
Last night it spontaneously rebooted and that was that.
Both laptops (with N adapters) are seeing the 2.4ghz network as 802.11g and my 300Mbps notebook adapter is seeing the 5ghz network as 802.11a. InSSIDer is showing that both networks are now broadcasting at a max of 54Mbps.
I have tried rebooting the router multiple times. I have also tried unplugging it for 60 seconds. I have also attempted to force the 2.4ghz to 20Mhz and a more optimal (unused) channel. That doesn't work. I tried setting the 5ghz network to wide (40mhz) with an optimal channel. Same deal. Still seeing it as 802.11a.
I have a cisco router model number E2000 it has worked fine until a few days ago, it keeps losing its signal on all my wireless devices I have reset it and it still is not working properly. I am wondering if I have to many wireless devices running through this router.
View 1 Replies View RelatedI just installed a Linksys WRT160N router. The signal started of good about 50 to 70 feet from the routers location. Now the signal is registering as low to good, about 54Mbps. I was wondering what options I might have to install a wireless bridge for expansion of the signal. I have configured an encrypted network using WPA2. I am wondering what the technical difficulty would be to install and configure it. I setup the WRT160N myself if that means anything.
View 4 Replies View RelatedAt one of our offices, we have a Cisco ASA5505 firewall that has dhcp enabled. I have a WRT54G router plugged into that firewall with DHCP enabled. The scope of our inside network is 192.168.51.***, however when connected to the WRT54G, it gives you the scope of 192.168.1.***We have an antenna amplifier screwed into one of the antenna ports on the router. This whole setup works fine.
The problem is we need to install an access point WAP54G in a building across the property (picks up router wireless signal fine) to repeat the wireless signal to the back of the property where the router will not reach. I have read that all you need to do is type in the wireless mac address of the routher into the access point and select "Wireless Repeater". I have the channels set to 6 on both devices as well as the same security configuration. When I try to connect to the wireless network on the access point, It never gives me an ip in the 192.168.1.*** scope, which the WRT54G is configured to give out. Also, in this setup does the WRT54G need to be set to router or gateway mode? I do not need it to distribute ip addresses. [code]
I bought a WRT54G v6 and since I installed and configured it I've experiencing an intermittent connection in my lan where you can find a notebook wireless connected to the router and a desktop wired to the router by cable.I'm working and then the network stops, both computers lose signal with the router. The signal come back few seconds later but to work in internet again I have to wait some minutes.So I contacted the live assistent on Linksys web-site and the agents said to me to do something that I will list here:- lower the MTU to 1480, 1470, 1450- updated the firmware- reflash the firmware- reset the router for about 30 seconds- do the power cycleIf you don't know what update and reflash the firmware or do the power cycle means you can srsistedthe conclusion is that ee the instructions on this pages: [URL] ...
View 9 Replies View RelatedI have a WLC 4404. I added a new AP to the network and it is associated with the WLC now. But still its not braodcasting the ssids. I compared the configuration with the ones installed before and configuration is same.
View 9 Replies View RelatedI have a Wrt160n router and a Motorola sb120 modem (provided by comcast after my original modem got fried by lightning, no I didn't have my router hooked up when that happened), I have been having trouble trying to get the modem to send the internet signal to my router. I have tried mac address clone that was suggested on this forum for someone with a different router but still no internet to my computer, its all hooked up through Ethernet cables, the computer I have it hooked up with a hard line is running windows seven. When I plug the modem straight to the computer it works and I have internet but when I hook up the router between them it has no internet.
View 9 Replies View RelatedI've had been successfully using a WRT400N to extend my wireless network as follows:
The WRT400N connected to my network via an Ethernet port in my kitchen. The cable ran down to a corner of my basement connecting to Verizon router that brings in our Internet, TV etc.
The Verizon router's poor location was a problem, and placing the WRT400N in the kitchen worked perfectly, providing excellent network access and Internet to wireless devices throughout my home. It worked fine for over a year.
Recently, we had a power outage which reset the WRT400N to factory settings. and I am having trouble getting it to work again. I set it up in the first place, but am now having difficulties. Clearly, I am no guru!
I tried to get it going again by: 1) plugging the WRT400N into a PC and giving it a new IP address that would not conflict with the Verizon router (both default to 192.168.1.1) 2) turning off DHCP, 3) renaming the router, 4) changing the router password, 5) setting up a WPA2 security key.
I then plugged the WRT400N back into the kitchen Ethernet port, but something is wrong. Wireless devices cannot find the WRT400N.
The good news is that I can "see" the WRT400N through any PC on the network via a browser and access setup, but the bad news is that devices cannot see or connect to the wireless signal.
When I go to "Status" it shows the IP address, subnet address and default gateway all at 0.0.0.0. On the SETUP page, it has the correct router address (192.168.1.9), and a subnet mask of 255.255.255.0. Not sure if it is supposed to be this way...
Just got the E4200 and it seemed great at first. Connected at 450mbps at close range (maybe 6ft away) and got 223mbps transfer.It seems that recently my signal is much weaker. I'm around 6-8ft away from the router and I'm getting between 270-360mbps, which to me is poor given the short range.InSSIDer says the RSSI is -50, while my other wireless N router (dual band) is -35 and is in the exact same location. I'm using the 5ghz radio only, and it is set to N, and I'm using channels 44 and 48. I checked the hidden advanced wireless page and transmit power is already set to high.My laptop has an Intel 6300 wireless card.I'm using the current firmware 1.0.02,I've noticed that the speed of the router randomly seems to drop off too (just as I type this, the link rate has gone back up to 450mbps... typical). Is the router throttling when it gets hot or something? So I just want to find out if others are experiencing similar rates at the same kind of distance. Seriously, how can you advertise something as 450mbps when you can't even get that link rate at a distance as short as 6ft?I can't see any thing I can do to increase the link speed (back down to 270mbps now), short of a firmware update to increase the power and use higher channels. I hear the higher channels are much better, so who do I have to write to, to plead for new firmware?,This is a great product, but it's totally ruined by stupid internal antennas and a weak transmit power.
View 1 Replies View RelatedI live in a single story bungalow, and im wanting to resite my EA4200 up into the roof space, just wondering which is the best position to mount it in for signal, horizontal or vertical, or doesnt it matter ?
View 1 Replies View RelatedSo here's my issue, I just bought this EA4500 so I could use the 5.0 Ghz and get a new 2.4Ghz as my old Netgear would drop the signal on a fairly regular basis. I've set the channel on 2.4 to 1, 20 Mhz Channel, and my neighbors are for the most part using channels 6 and 11 (one guy is using channel 2 at 40Mhz but has a very low signal strength). The signal drops out sometimes as often as every 5 minutes, and now it is doing it on my new router. Here's the kicker, the 2.4 band falls out from my router and some of my neighbor's routers, no new signal seems to come up, but the 5.0 band on the EA4500 is just fine, as is the wired route. Is the 2.4 band just being assaulted at my home and I'll have to deal with it, or is it that my new router, old router, and my neighbor's routers, all suck, and we should all get refunds? Any solutions to troubleshoot this beyond running a netstumbler like software, setting hard channels (including width), and long hours of trial and error? I am running this all from my macbook air, the 5.0Ghz is at 40Mhz, is the only signal, and is on a fixed channel.
View 7 Replies View RelatedI have a Linksys E3000 router set as Lan-Lan 192.168.0.2 hosting my internal LAN connected to a motorola Surfboard (Brighthouse) internet Wireless/Wired access point 192.168.0.1.I have a Web server hosting a site connected direct to the surfboard (works fine) . The FTP "site" on the E3000 can be seen by all pcs on the internal LAN. However, it can NOT be seen from the internet (Android with FTP client being used for test device)
Primary Access point 192.168.0.1
DCHP server with reserved IP addresses for server and PC's and smartphones
Port Forwarding Set for Server at 0.004 : 80
Port Forwarding Set for E3000 at 0.002 :21
Secondary (E3000) router 192.168.0.2
DCHP server is disabled
Port Forwarding is Not being used
connected to primary router LAN port 1 by LAN port 1 on E3000
All pc's can access the Internet when connected to the E3000 via cable or wireless?All pc's can access the FTP server on E3000 via cable or wireless as a LAN location (connected to either router)?How can I get the FTP to be seen from the internet ?
I recently bought a Cisco e3000 router. I updated the firmware but I am still only getting 1.33 Mbps at most. The only things plugged into it is my PC and my xbox. I bought the router so i could get a better connection on my xbox so netflix wont stop playback.
View 9 Replies View RelatedI have an e3000 that cannot obtain an address from the ISP. I can get an address on the computer and an old router by directly connecting the cable to the computer or the router. I can also daisy-chain the e3000 to the old router, and I can get an address on the e3000 from the old router. I have hard reset the e3000, changed firmware from the Linksys to TomatoUSB and back to Linksys, and I still can't get it to work. It worked fine on Saturday until a bolt of lightning hit close to the house. Since then, I cannot get the e3000 to connect to the ISP.
View 9 Replies View RelatedHow do you set up the E3000 for ATT u-verse?
View 2 Replies View Relatedinstall linksys e3000.
View 1 Replies View RelatedI had a failed Tomato upgrade and now Connect Setup can't see router to revert back to original. I get message 82BD0101 or computer not connected to router. Also the http://192.168.1.1 trick won't work. Is there any way to restore besides 30/30/30?
View 2 Replies View RelatedI would like to override the DNS servers provided by DHCP via my ISP. The other settings I would like to preserve (like my assigned IP).How to achieve this with E3000 ?
View 3 Replies View RelatedIt seems like after a certain amount of time, maybe a few days... my E3000 gets slowww.. I'm talking dog slow. And it's not just the internet, I have a media server connected to it, and usually when I put something on it, the transfer rate is about 3.5MB/s (not bits, bytes). But everything is slow, I top out at speed of maybe 1/6 normal on the internet as well.
View 8 Replies View RelatedWe have a wireless internet service. Not satellite. We basically have an antenna on our house that picks up the signal from a tower a mile or two away. I used the e3000 router when we lived in town with broadband internet and it worked fine. I can't get it to keep a hold of a signal. I can connect to the router from the computers but the router drops the signal from the tower. I have an old router that the wireless company was kind enough to lend me that works , but the signal is weak and it could die at any moment... I"m at my wits end.. I have an expensive piece of equipment that wont hold the signal. I have updated the firmware and the Cisco connect software..
View 5 Replies View RelatedHas anyone tested QoS on the new E3000? Whenever I add an application (e.g. Voice Device) and set priority to Medium or High, my upstream bandwidth for everything else is immediately cut significantly, even when I'm not using the priority application.
For example, with QoS disabled, I can consistently get 10Mb upstream (speedtest.comcast.net). As soon as I enable QoS, upstream is capped to exactly 2Mb! On my old router, there was an option to set the total upstream bandwidth -- but on the E3000 there is no such option that I can find.
just bought an e3000 and want to use it with wireless internet- usb modem. when setting up it wouldnt go any further than the 'searching for connection' page as it couldnt detect a connection in the 'internet' lan (wan?) port.can i set it up to accept the wireless usb modem?
View 6 Replies View RelatedI lost my cd for my router e3000 any way still to use it?
View 1 Replies View RelatedI just bought an E3000 about 30 hours ago and just unrealistically my router now doesn't want to give me any WiFi at all. I tried reset button, tried re plugin all of my system as well as pressing for short and long period the middle button that indicates WiFi is accessible. I already bought 3 linksys routers.
View 2 Replies View RelatedLooking at upgrading my router to an e3000 however I've got a couple of questions. I might come across as a bit thick with this one but I have read that you need a modem to make the router work, I can't get my head around this as I've not come across this before. I always thought the router was the modem!! I've also heard that the E3000 only works with cable ISP and not ADSL, is that true?
View 2 Replies View Related