Linksys Wireless Router :: Not Allow Devices To Access And Make Changes To EA2700
Jan 17, 2013
I have an EA 2700 installed using a wired network. It is just one desktop computer and a VOIP box shared by my internet connection. I am quite new at wireless connectivity.I would like to add wireless devices, specifically a phone and a laptop, but I do not want ANY of the wireless devices to be able to access and make changes to the ROUTER or any other computers on the network. I do need to keep the network secure.How do I set the router and/or devices up to accomplish this?
I'm having a problem where my connection speeds slow down on my iOS devices. I have a EA2700 router. I have PC hard wired into the router, which maintains steady speed test numbers when other devices slow down.i have another pc that connects wirelessly (2.4 only) that maintained speed white the other devices slowEd down. Both my iphone5 and new iPad would slow down. The quick fix wasto turn the wifi on the device off, then the speed would return when reconnected. Also clicking "renew lease" in the iPhone wireless settings seemed to correct the issue.I'm not sure if there is a setting on the iOS devices or the router I can change to stop this.
I have been using the E3000 for quite a while. A problem that I could not find a solution to is that the devices connected through Ethernet can't be viewed on Wireless, and vice versa. This is especially annoying because I want to get access to my media servers over wireless, for obvious reasons, but even those are not viewable (and using IP addresses on portables is a pain in the back)
I recently purchased an EA2700 to replace an old Belkin. I ran the set up CD and I am unable to establish an internet connection. I am able to connect to the router (both wired and wireless), ccess the settings, etc but cant reach the net. I've tried turning off the firewall, flushing the DNS, disabledthe IPv6. Did all the basic steps, resett the modem/router, etc...nothing. i hook the Belkin up and it connects just fine
Every time after the router (Linksys EA2700) is powered off and restarted, there is no interent access available. The router configuration status reports an Internet Address of 0.0.0.0 and all the devices at home are left with a wifi without Internet access. I have to unplug the WAN from the router and plug it in again while it is turned on to restore internet access (and a normal Internet Address is seen from the status page). The WAN works fine with the routers I had previously. I wonder if I have to perform this every time I power on the router. I have tried resetting the router and reinstalling Cisco Connect but that didn't work.
I have a Cisco outer EA2700 connected using a Lan cable, Lan cable works fine as I connected it directly to my PC, I am unable to access wifi network connection, I am able to search the router and also able to cnnect to the router, But wireless connection shows limited or no connectivity, and unable to access any websites. It was working fine till yesterday, I tried rebootng ad also unplug and replug the network cable also reset the router but does not work
I have a domain name which I register to my WAN address so I can do service hosting from my home network. I recently switched out my WRT54G running DDWRT with an EA2700. I set up my port forwards and static dhcp assignments and they are working from outside my network, but when I try any network operation involving my WAN address from my LAN machines, the connections just timeout.
I read in some posts that "you cannot do this" and "you have to test from a remote internet machine". Well, this WORKED with DDWRT, so it's not like it's impossible to make a router that does this. Why can't I do this with the EA2700? Is there some magic setting that will let this work??
The whole point of using a domain name is that I can access my services ANYWHERE using the convenient "name" thing.. genius, right? Except when I bring my laptop home and suddenly my domain goes non-responsive.
I can't find info about Access Restrictions in new series of routers.[URL]Do new routers have both Parental Controls + Internet Access Policy? I need this [URL]
I am wanting to access my IP camera over the Internet. I am not a computer wiz by any stretch and after a couple of failed attempts. My ISP is Comcast and they say that I have dynamic dns and should have no issues viewing my cameras. I know how to get to the port forwarding area of the router but am confused as to which ports to forward. The set up instructions for the camera (Airsight) suck. Screen shots of the set up don't match the actual router
I've had this router for about 3 weeks. It's only 20 feet from the computer, but my computer on 2 or 3 separate days had trouble staying connected. The signal dropped to 5 Mbps and had a little yellow symbol that said no internet access and when I looked at the properties it said, "limited or no connectivity." I got impatient and purchased a 75 ft Ethernet cable online with plans to possibly return the router as I don't really need wireless anyways and since I spent $100 on this router I expect it to work at 20 ft distance.
For the last few days it has remained at 54 Mbps or more sometimes all the way up to 108 mbps. But now since it got pretty low a few times I don't trust it enough so I might return it anyways.IPv6 connectivity says no network access. This might be because when it asked for administrator password to recognize it as a trusted home network I closed it instead of putting in the password.
I purchased Linksys (Cisco) EA2700. For the moment it is being used as an access point for a wireless network (WLAN) and an Ethernet switch. 4 laptops are being connected to it through the wireless network, the wire connects one computer and a separate ADSL modem (it is used for accessing Internet). As a result minimal ping to any of the devices in wireless network is 8 ms – the best result and sometimes rises to 20 ms. Consequently when working with local network resources one suffers from speed decrease. Ping to the access point through the wire varies from 1 to 8 ms. These delays are quite strange as even on cheaper routers ping does not rise above 2 ms (usually <1ms). Is it normal for the device?
I have an EA2700 running latest firmware 1.1.38.138827. It is using Cisco Connect Cloud. I am unable to access the DHCP Reservations link under Connectivity/ Local Network. When I click on it, nothing happens. I've tried multiple browsers including IE 10 (Windows 8 RTM), Firefox 15, and Chrome 21. I also tried on a Windows 7 machine with IE 9 and the link doesn't work on that either except that it shows a box that says Invalid Character when I click on the DHCP Reservations link. I see no invalid characters on the screen. Any workaround other than downgrading the firmware or assigning static IPs on individual PCs?Also, on an unrelated note, where is the Dynanic DNS configuration on the Cisco Connect Cloud?
I want to use my WRT160n in my room to connect all my devices (Xbox, playstation 3, and 3 laptops) I hardwired the E3000 from the room downstairs thats connected to everything else.
I just set up my e2000 on a PC using Windows 7. I am additionally trying to set up additional devices on the network. The two that I am currently working with are:Dell Latitude d240 running Windows XP.HTC Evo smartphone running Android
I can't get these on the network through the e2000. They can access the internet through the e2000 but only as a guest and therefore don't have the same level of security. What do I need to do to successfully put the above devices on the network?
My PC will connect just fine, but it is the only device on my network that the router will allow internet access. The router will allow other devices (DVR, laptop, nook) to connect to it, but won't allow those devices to connect to the internet. Each device will show the same error, - "connected to linksys - no internet". I've reset the router many times with no results.
I just switched to the EA4500 Router and I'm now unable to remotely access my camera devices. I have done the port forward. I can access the cameras from my local LAN both when using the local 10. ..and external 99 .. Addresses. When I go off the local connection - Access does not work. Slingbox did its auto configuration and I can access it. I just cant get to camera devices (Panosonic, Foscam, etc.).
I have a WRT54g with Tomato firmware. I am trying to set up a WAP54g to extend the range but while that access point does show up as a network, nothing can connect to it. I already have the router's MAC address put in the WAP. I think the problem is that I have Tomato on the router and that conflicts with the default firmware on the WAP. Range isn't really the problem, I just need to strengthen the signal in a specific area that it's not getting to because of walls. I can't even switch to previous versions of Tomato anymore. I may have just bricked it.Some facts about my setup-My modem has default settings: PPPoE connection with a DHCP server enabled.-I set the router to use DHCP and put it in "Access Point" mode.
-The WAP is set to repeater mode and it was set to Static IP configuration by default. I simply followed the instructsions here: url....
-There are three different MAC addresses: The WAN, LAN/router, and the Wireless. I put the Wireless MAC address in the access point. Is that correct?
-My desktop is wired directly to the router and it has a static IP outside the router DHCP's IP range-UPnP is enabled by default in the modem and router, but I'd like to try to get this working rather than buy all new equipment.
I would like to schedule my boys ipods to be on the network from 2:00pm to 4:00pm each day.
Running the Cisco connect software it would appear I can schedule from 2pm until the next morning but not a 2 hour window in the same afternoon.
Looking through other posts I see earlier software where this can maintained through the Router firmware but with 1.0.04 I seem to have to use Cisco Connect.
So how can this be done with my current configuration ?
I am running the e3000 as an access point.. My iphone and ipad connect to it seamlessly. After a few hours to days, they are no longer recognized by the router. Nothing I reset on the phone or ipad makes any difference. The only solution I have found is to re-boot the router. They then re-connect on their own.
i got an ea2700 and i cant get the external to work internally which i need for server tests now this has worked before on every other router i had without any editing done but this one doest allow that so what can i do to make it work with this router?
I have EA2700 Router which support to be a dual-band wireless router and I am trying to connect to my router using 5 Ghz band with AE2500 Dual-Band Wireless-N USB Adapter, I am only seeing 2.4 Ghz wireless band plus even if I manually enter my 5 Ghz SSID my network adapter still wouldn't work on 5 Ghz band. Is there any specific set up in order get 5 Ghz band to work?
My first issue with this device is when I try to untick NAT to disable it I lose my internet connection. This also disables access to router's address 192.168.1.1 forcing me to reset the device and set it up all over again. Why is this happening? I tried this at least five times with the same result. Second question I have is if the DHCP reservation is the right option if I want to forward ports for certain applications like Vuze? When the DHCP reservation window opens I see all my wireless devices in the list (laptop, phone) but not the main computer which is connected through ethernet port. But that is yet another problem.
I've got a cable modem, connection is set to Automatic DHCP and I all want is to disable all firewalls, NAT and other unnecessary protection that's slowing my internet speed, set up MAC address filtering, port forwarding and close this terrible software so I never have to see it or think about it ever again.
i have a EA2700 router and I'm connectied wirelessly to my PS3. If i am not hosting a game i will be lagging all over the place yet it says i have full connection to majority of games that i connect to. i paid 115 dollars for this router and am very dissapointed that its doing this. Also no there is no way for me to connect wired to the router it is to far away. Also i tried bringing my ps3 to my friends house and played on his wireless connection and it worked perfectly so its deffinetly my router.
EA2700v1 WPS-PIN using 5GHz does not work. This router includes WPS header in its 5GHz beacon and probe response but the router removes the WPS header from them once WPS-PIN starts. There is no problem with WPS-PIN using 2.4GHz.
I am not able to access the web interface of the router.No, i am not using cisco cloud or smartlink .. yes, it has the latest firmware (Ver.1.0.14.129982).Yes, I might be able to get to it if i shut down the router and turn it on again a few minutes later, but the problem is.. why? why do i have to interrupt connections and not have internet to log into the admin web interface of this device? Is there a known problem with it that makes the webservice go down?.. or to take extremely long to respond and thus the browser to quit on it throwing an error?
Im not able to conect to the internet threw my router, but i am able to with my modem. i dont want to pay for a new one and Cisco wants me to pay $30 for phone support.
Where can I find a log or list of devices that attempted to access my EA4500 wireless network?I am using the cloud services to monitor my EA4500 usage in an apartment environment.
My new EA 2700 disconnects from the internet if the desktop is idle for more than 30 minutes. needs to be unplugged for a few minutes then it will reconnect. This is an unacceptable situation and this thing will be tossed if it cannot be fixed. Can this be reset so it won't disconnect? or do I need to replace it with a product from another company?
I have an Cisco EA2700 router and a Motorola SB6121 modem. If I'm connected to the router wirelessly or through any of the lan ports, I can't visit the modem's diagnostics page at 192.168.100.1. If I connect directly to the modem, it works fine. Also I cannot ping the modem through the router, just get a timeout. My ISP is Comcast.
I have tried all the speed test sites and tried downloads with and without my EA2700. Every test shows about half the perfomance when connected through the router. My speed tests at speedtest.net with a direct connection are in the 21-26Mbps range, the same tests run about a minute later through the EA2700 fall in the 10-12Mbps range with spikes up to 17Mbps.I've reset the router and modem.I've gone back to the 1.0.14.129982 Firmware (which it's currently on)I've set the MTU everywhere from 1400 to 1500 (literally EVERY setting for at least a couple of hours) it is 1492 currently. None of these have worked. In addition, when a large stream starts, such as a Steam download, I will lose ALL connectivity. Going in to Network and Sharing and clicking to connect to the internet restores the connection, no need to reset any hardware (which is odd in itself). I have had MANY routers over the years and I've all but exhausted support with service provider as the connection is solid if I eliminate the router.Main machine is a Windows 7 Home edition Total of 5 machines, 3 of which see regular use All machines go through a Trendnet 16 port switch and performance is the same direct or through the switch I m on Brighthouse in Central Florida and have all but exhausted their support.
I recently bought an EA2700 in hopes that it will make my connection faster, stronger signal and stable. However, this is not the case. The connections keeps dropping and the range is the same as my Verizon-FiOS router. Anyway, I'm hoping that a fix be distributed to address this issue. I can't return my router to the vendor anymore.
Now, since I have two routers, I want to be able to leverage EA2700's dual-band feature and the Guest-access feature but I can't make this as a main router since my FiOS router should still be able to supply IP addresses to my cable boxes, thus, I can't configure it as a Bridge. I'm thinking if I just split the IP distribution as follows:
