Linksys Wireless Router :: WRT120N - How To Prioritize Computer's Bandwidth
Apr 20, 2013
I have a Desktop wired to my WRT120N. With this router being a wirless one, we have other devices (2 laptop and 2 iPads) conected to the internet via WiFi.The thing is, whenever I play an online game (specifically, League of Legends) my ping skyrockets whenever they use the internet.Is there a way for my PC to take priority in bandwidth over theirs? Or at least some way for my game to take priority over theirs?
Telefonica router (this my internet provider) --> WRT12N --wireless/eth--> my laptop
With that configuration I get a 1Mbps band with But in this configuration Telefonica router (this my internet provider) -- wireless/eth--> my lapto I get 7Mbps.Using always the same port of my telefonica router.Why the WRT120N is not providing the whole bandwidth? Is there any option in the router that divide the whole bandwith (7Mbps, almost 8Mbps) among the four ports of the wrt120n (giving 1Mbps per port)
Before, I can access admin panel of router via 192.168.1.1 on any computer, be it wired or wireless.This time, I can't anymore.This time, I can only access admin panel on 1 computer only. The computer in which it's directly connected to the router, wired. All other computers, connected to a switch, which the switch is also connected to router, can no longer access admin panel.I can still open 192.168.1.1 with a username/password prompt but I can't log in. It's like it's always wrong password. Same with accessing from laptop (wireless).Before, I can access admin panel from any computer (wired), even from laptop (wireless). There are times that I have to restart router in order to fix my internet connection. Only this time, I have to access it from the computer that's directly connected to router (wired).How do I revert it back so that all computers will be able to connect to admin panel of router?I have just finished upgrading firmware from 1.0.05 to 1.0.06 but I still have the same problem.
I just bought a WRT120N and at different times it will randomly restart and disconnect all the computer on my network I have 4 wired devices and 4 Wireless devices.
I am working on Videoconferencing solution between two location. locations are now being connected through IPSEC site to site VPN. Since we are having a common internet link for VPN as well other corporate use we have to prioritize the internet bandwidth for Videconferencing. is there any way i can prioritise videoconferencing traffic by ports? following are the configs done on the cisco 2801 router with Version 12.4(15)T10.
!interface FastEthernet0/1description ILL_12Mbpsbandwidth 20480ip address 94.*.*.180 255.255.255.248duplex autospeed autopriority-group 1! ip forward-protocol ndip route 0.0.0.0 0.0.0.0 94.*.*.* !!no ip http serverno ip http secure-serverip pim ssm default access-list 199 permit ip host 94.*.42.* host 78.*.*.130 ( VPN peer IPs both ends)priority-list 1 protocol ip high list 199
I have a Cisco WRT120N Router and a Cisco Valet AM10 wireless adapter. Almost every time the computer reboots, I loose my network and I have to redo the AM10 setup. The AM10 is the only device that loses the connection, my lap top and printer do not lose the connection.
Problem 2: Everytime I upplug and replug the AM10 a window pops up saying I need to check the drive for errors but none are found.
Problem 3: I downloaded the AM10 install program, Downloadable.Setup.AM10.1.2.10148.2. It does not work. If I try to run it Iget an error message that the setup canot be completed and to call in for support.
Problem 4: When I can get it working is shows that it is Wireless Connection 5. Why 5 and not 1? Where are the other 4?
I have a home PC Windows 7 desktop and a Linksys WRT120N wireless router for another computer currently. I need to add a VPN and a desktop work computer (XP) to the above.
I bought a new Linksys WRT120N modem which is working great, but the wireless for some reason isn't working properly. My computer is able to sense the exsistence of the connection tho. I've tried using other computers to connect to it, and still the same problem, can sense but cannot connect.
I currently have a network using ipaddress 10.1.x.x and 10.2.x.x and 10.3.x.x with a subnet of 255.0.0.0 I purchased 2 of the wrt120n wireless routers for testing and find I can not use the subnet of 255.0.0.0.
I have a WRT120N and have been trying to set up priorities using the QoS under the tab Applications and Gaming. Everytime I "Save Settings" it does not save. It refreshes the page and deletes everything I just set up.
I did Live Chat and they told me it was my router. I returned it and got another one... Same problem
I'm using an Static IP adress and i'm using wrt120n router, but to connect the internet i have plugged the internet cable in the 1,2,3,4 (doesn't matter which one) slot. So now i'm just using the wirelss part of the router without "routering" if i can say so. When i put the internet cable in the Internet slot of the router, the laptop just cant connect to internet - it shows Unidentified network without Internet Access. I don't know what type of changes i have to make in the WEB interface of the router. I think i have to set the type of the connection - now is DHCP and may be to put my IP adress, DNS, Subnet mask in the router settings, but don't know how exactly. I've tried to set up the router with the CD-interface but same thing happened - Unidentified network when the cable is plugged in the Internet (yellow) port. How to set up the router to be a router, not just a wireless switch?
My roommate and I recently got a WRT120N to replace an older Linksys router that was exhibiting the same problems with less frequency. Indeed, the entire reason we got the new router was to fix these problems. Alas, they have become worse.Anyways, what's happening is that the router constantly resets itself. It does this every 20 minutes to an hour and doesn't seem to be related to how much traffic it's dealing with.It's not just the internet going down, it's the entire network, and not even just the wireless part. My computer has a wired connection to the router and, and I get told "A network cable has been unplugged" every time it happens. Then, if I look down at the router, I see no flashing lights, just the steady glow of the power light. It always fixes itself after 10-15 seconds, but it's very annoying. Certainly, playing games online or having a conversation on Skype is made more difficult.As previously mentioned, we replaced our older router because it was exhibiting the same behavior, but the new one does it with greater frequency. At the very least, the router does reset itself instead of needing us to cycle the power. The setup was slightly different with the old router: I was using a wireless connection with a WMP54Gv4 which I've had to disable since it bluescreens the moment it so much as sniffs a signal from the WRT120N?
Is there anyway to disable WPS on the WRT120N router?
All I can do is switch the "view" from WPS to manual configuration in the management console...this doesn't actually disable anything.Maybe I don't understand WPS security, but what's the point of using a 20 character WPA2 password if WPS has an 8 digit PIN that I can't change or disable?
I just bought a WRT120N to set up with my new Gateway Windows 7 64-bit using Cablevision cable internet. When I go through the steps from the CD to install, the wizard does not find the connection. When the internet is plugged directly into the computer, it works fine. If I have the router plugged in first and then run the install CD, it picks up the router as an existing router but I can't get it to install
I have a WRT120N router installed in my office.All PC and Laptops are connected to it via WiFi.there are about 3 PC and 4 Laptops.The WiFi keeps going Off now and then..and comes back on in a minitue or so.
I plan on replacing my linksys BEFW11S4 wireless router with a new linksys WRT120N wireless router. Should I completely remove and unplug the old router before inserting the startup CD and beginning the installation process for the new router?
I have several computers and printers connected to a WRT120N router which is connected to 10mpbs DSL. The computers are all running WIN7 and are hardwired to the router. On the one PC, it keeps losing network connection. I've tried upgrading the router's firmware, reset, etc. to no avail.
I think it may be related to the same IP address being assigned to multiple machines connected to the router. Is there a way to set specific IP addresses to each item connected to the router to see?
I don't have any problem with the wireless computers connected to the router but the wired one keep geeting disconnected. I'm loosing the internet many times a day on thiis one. Like I said the wireless is ok. My old router on my computer ( wired) was working well before I installed the wrt120n.
I've recently bought a WRT120N router, when I install the router using the CD an error occured error 322 New router or gateway not detected. I tried to download new version of firmware but it didnt work.
I can't access the web based setup via 192.168.1.1. I've had this problem since I swapped to Static Ip from PPPoE. I changed internet provider and now when it type 192.168.1.1 in the browser it says Internet explorer can't show the web page. I've tried Crome and FireFox but with the same result. I followed the instructions in [URL] but to no result.
I replaced a WRT120N router with a new one thinking that the old one was damaged. During setup, the router wasn't recognized. I used the same connection for a line from the internet to my LAN connectin and the line works fine. Connecting through the router is no good.
I am considering to purchase a Linksys Wireless router, but I just don't know which one to select.There are so many different types that seem to have very similar (if not equal) specs.If I just limit myself to the WRT120N, the WRT160N and the E1000, they all have 4 ethernet ports (10/100), and they all support 802.11 b/g/n for the wireless part.Obviously they all promise a blazing performance, and wireless coverage throughout the whole house, without (many) blind spots.But if their specs are the same, why are they different types?
Several days ago there was a huge storm, and I think a thunder burned the WAN port of my linksys wrt120n router. Everything else is working good, I can detect the local network but I don't have internet. My internet connection is also working good. My question is, do I have a possibility to use some of LAN port like a WAN? I'm only using 2 of 4 LAN ports. It would be very useful because it's a pity to buy another router just for a not working WAN port.
I am trying to manually setup a WRT120N router. I am using my laptop (hard wired) for the initial setup. Okay, everything is working fine until I unplug the ethernet cable and try to go wireless. Will not connect to my network. I am also having this problem with all my other devices.
I had everything running fine on a WRT54G, I just wanted to try out the WRT102N. I did change the SSID name form what I was using on the WRT54G.
I'm having an issue where essentially my only course of action is to unplug the router and plug it back in. I can connect my laptop (Dell Inspiron N4010) and my phone (HTC Inspire) once. But then if I put my computer to sleep, or I take my phone out of the wireless range and come back, I cannot connect again. I've gone through and played with the settings (changing the upnp, the beacon intervals, the channel, etc) but to no avail. Invariably, I always have to come back to unplugging and plugging back in.
Also have a Kobo E-Reader and a wireless Canon printer. The whole point of a wireless printer was so that it would stay connected and I can print from my laptop. This router is making this useless.
My mother in law bought my daughter a impression android tablet for Christmas it connects fine at public hotspots but I can not get it to connect to our wrt120n router at home. I have tried everything I know to add it. It asks for the password then says getting IP address then disconnects.
how to get the factory firmware version 1.0.01. I have a problem with the settings. I want to return to the basic version, but can not find anywhere else.
