I replaced a WRT120N router with a new one thinking that the old one was damaged. During setup, the router wasn't recognized. I used the same connection for a line from the internet to my LAN connectin and the line works fine. Connecting through the router is no good.
View 1 RepliesI just got E1000 cisco wireless router. Started setup, everything worked fine and replaced admin password with my own. For some reason got error message. tried to redo setup and got message router not recognized. used laptop and found out that wireless works fine. After few days noticed that there is a (mynetworkname) guest connection you can connect without any password. i don't need that stupid thing and my question is how to disable guest network? I cannot reach Main Menu from cd and have no idea where to look for it when i connect to router by web.
View 9 Replies View RelatedI'm using an Static IP adress and i'm using wrt120n router, but to connect the internet i have plugged the internet cable in the 1,2,3,4 (doesn't matter which one) slot. So now i'm just using the wirelss part of the router without "routering" if i can say so. When i put the internet cable in the Internet slot of the router, the laptop just cant connect to internet - it shows Unidentified network without Internet Access. I don't know what type of changes i have to make in the WEB interface of the router. I think i have to set the type of the connection - now is DHCP and may be to put my IP adress, DNS, Subnet mask in the router settings, but don't know how exactly. I've tried to set up the router with the CD-interface but same thing happened - Unidentified network when the cable is plugged in the Internet (yellow) port. How to set up the router to be a router, not just a wireless switch?
View 9 Replies View RelatedI can't access the web based setup via 192.168.1.1. I've had this problem since I swapped to Static Ip from PPPoE. I changed internet provider and now when it type 192.168.1.1 in the browser it says Internet explorer can't show the web page. I've tried Crome and FireFox but with the same result. I followed the instructions in [URL] but to no result.
View 1 Replies View RelatedI have been using Mozilla Firefox for about 5 or 6 years now, and I have always been able to access any router setup through Firefox. Now though, I strangely can't. I try to log in from Firefox and I get stuck at the log in dialog box even if I use the correct password. If I cancel, the router assumes that I do not know the password and I get the standard Linksys access denied page. I then start using IE[current version], and I can log in absolutely fine. I can still use Firefox to browse the internet. I can ping the router. I can use Firefox to access the router setup from a different machine.
[code]....
I setup a WRT120N router in my home. I am having a issue getting good coverage over my single floor ranch style home. Would changing the Standard Channel (currently set 6) make a difference?
View 9 Replies View RelatedI have a Linksys E1000 router which was working fine. My hard drive crashed; I replaced the hard drive and now my router is not recognized. I have reset it and tried to reinstall it with the CD. Nothing works.
View 1 Replies View RelatedI have an EA2700 (fimware "classic" 1.0.14.129982) that used to work perfectly fine with a Comcast cable modem. I just recently switched to Charter with an Arris TM902 modem and that's where the problems started. The cable modem will not recognize my router. I have to plug in a computer into the cable model when it starts up. Then I need to clone the MAC address and restart the router (after disconnecting the computer). Why isn't the cable modem recognizing the router when I restart it? I guess this could work if it would be a one time thing but I had to power-cycle the modem and it stopped recognizing the router even with the cloned MAC address. So I had to do the whole spiel again.
Is there any way to make this work easier? Should I update my router's firmware to the "smart" one?
I have an E4200 wireless router and have bought myself an external hd for media sharing (STOR.E STEEL S 1TB disk (PA4252E-1HJ0). Unfortunately this disk comes with a Virtual CD partition on it, which can not be deleted or removed (url....)!! Despite this being massively annoying by itself it also renders my disk useless, as my router does not recognise the disk (to to the additional partition). Is there any possibility to extend the firmware or to provide a fix that allows me to use the partitions on the disk, despite this additional "virtual" device?
View 6 Replies View RelatedYesterday i upgraded my e4200 to firmware version 1.0.02 (Build 13) after waiting since february.Unfortunately it still doesn't recognize my WD 500 GB Essentials.
View 9 Replies View RelatedI have a E3000 and just upgraded my Mac with the OS X Mountain Lion. I can't access my external HD anymore, although when I go to the router set up, on the storage tab, the router appears to recognize the HD.
View 9 Replies View RelatedI just updated Cisco software and my external hard drive is no longer recognized by Cisco. It is a Seagate drive that is listed on the Cisco tested - passed - approved list. It worked prior to this update. I have disconnected the drive. Reconnected it. Rebooted. Turned machine and router on and off and its still not recognized.
Model name: Linksys E4200
Model number: E4200
Firmware version: 1.0.03 build 14
Operating system: Windows 7 SP 1
Software version: 1.4.11266.0
Connection type (WAN): DHCP
I am trying to setup a hard drive through my network to be recognized on all my devices.Here is what I have:
router: Belkin n300 max share F7D7301
modem: RCA cable modem
Internet provider: Teksavvy (through a Rogers line)
Hard drive: WD Elements 2TB HD (formatted NTFS)
Antivirus: AVG Free
ps3
laptop (running xp)
galaxy s3
The ps3 is wired into the router, the laptop and s3 are wireless. I have connected my hard drive to one of the USB drives on the router. I can see the HD and view any of its content (movies and music) on the laptop, but nothing else. My ps3 and s3 are connected to the internet, however I can't find the drive.
Linksys WRT120N to 811.11n? I set to 811.11N Only with 40Mhz, saved and reboot the device but the signal continuous in 811.11g.
View 3 Replies View Relatedpassword is not recognized bythe Linksys router
View 2 Replies View RelatedI bought a new Linksys WRT120N modem which is working great, but the wireless for some reason isn't working properly. My computer is able to sense the exsistence of the connection tho. I've tried using other computers to connect to it, and still the same problem, can sense but cannot connect.
View 8 Replies View RelatedI currently have a network using ipaddress 10.1.x.x and 10.2.x.x and 10.3.x.x with a subnet of 255.0.0.0 I purchased 2 of the wrt120n wireless routers for testing and find I can not use the subnet of 255.0.0.0.
View 9 Replies View RelatedI have a WRT120N and have been trying to set up priorities using the QoS under the tab Applications and Gaming. Everytime I "Save Settings" it does not save. It refreshes the page and deletes everything I just set up.
I did Live Chat and they told me it was my router. I returned it and got another one... Same problem
My roommate and I recently got a WRT120N to replace an older Linksys router that was exhibiting the same problems with less frequency. Indeed, the entire reason we got the new router was to fix these problems. Alas, they have become worse.Anyways, what's happening is that the router constantly resets itself. It does this every 20 minutes to an hour and doesn't seem to be related to how much traffic it's dealing with.It's not just the internet going down, it's the entire network, and not even just the wireless part. My computer has a wired connection to the router and, and I get told "A network cable has been unplugged" every time it happens. Then, if I look down at the router, I see no flashing lights, just the steady glow of the power light. It always fixes itself after 10-15 seconds, but it's very annoying. Certainly, playing games online or having a conversation on Skype is made more difficult.As previously mentioned, we replaced our older router because it was exhibiting the same behavior, but the new one does it with greater frequency. At the very least, the router does reset itself instead of needing us to cycle the power. The setup was slightly different with the old router: I was using a wireless connection with a WMP54Gv4 which I've had to disable since it bluescreens the moment it so much as sniffs a signal from the WRT120N?
View 9 Replies View RelatedIs there anyway to disable WPS on the WRT120N router?
All I can do is switch the "view" from WPS to manual configuration in the management console...this doesn't actually disable anything.Maybe I don't understand WPS security, but what's the point of using a 20 character WPA2 password if WPS has an 8 digit PIN that I can't change or disable?
I just bought a WRT120N to set up with my new Gateway Windows 7 64-bit using Cablevision cable internet. When I go through the steps from the CD to install, the wizard does not find the connection. When the internet is plugged directly into the computer, it works fine. If I have the router plugged in first and then run the install CD, it picks up the router as an existing router but I can't get it to install
View 4 Replies View RelatedI have a WRT120N router installed in my office.All PC and Laptops are connected to it via WiFi.there are about 3 PC and 4 Laptops.The WiFi keeps going Off now and then..and comes back on in a minitue or so.
View 9 Replies View Relatedwhy are some of the lines solid & others dotted on the map page?
View 4 Replies View RelatedI removed my ps3 from my network map and now i can't connect it back. How to do it?
View 1 Replies View RelatedI plan on replacing my linksys BEFW11S4 wireless router with a new linksys WRT120N wireless router. Should I completely remove and unplug the old router before inserting the startup CD and beginning the installation process for the new router?
View 3 Replies View RelatedI have several computers and printers connected to a WRT120N router which is connected to 10mpbs DSL. The computers are all running WIN7 and are hardwired to the router. On the one PC, it keeps losing network connection. I've tried upgrading the router's firmware, reset, etc. to no avail.
I think it may be related to the same IP address being assigned to multiple machines connected to the router. Is there a way to set specific IP addresses to each item connected to the router to see?
I don't have any problem with the wireless computers connected to the router but the wired one keep geeting disconnected. I'm loosing the internet many times a day on thiis one. Like I said the wireless is ok. My old router on my computer ( wired) was working well before I installed the wrt120n.
View 3 Replies View RelatedI've recently bought a WRT120N router, when I install the router using the CD an error occured error 322 New router or gateway not detected. I tried to download new version of firmware but it didnt work.
View 9 Replies View RelatedI am considering to purchase a Linksys Wireless router, but I just don't know which one to select.There are so many different types that seem to have very similar (if not equal) specs.If I just limit myself to the WRT120N, the WRT160N and the E1000, they all have 4 ethernet ports (10/100), and they all support 802.11 b/g/n for the wireless part.Obviously they all promise a blazing performance, and wireless coverage throughout the whole house, without (many) blind spots.But if their specs are the same, why are they different types?
View 2 Replies View RelatedSeveral days ago there was a huge storm, and I think a thunder burned the WAN port of my linksys wrt120n router. Everything else is working good, I can detect the local network but I don't have internet. My internet connection is also working good. My question is, do I have a possibility to use some of LAN port like a WAN? I'm only using 2 of 4 LAN ports. It would be very useful because it's a pity to buy another router just for a not working WAN port.
View 3 Replies View RelatedI am trying to manually setup a WRT120N router. I am using my laptop (hard wired) for the initial setup. Okay, everything is working fine until I unplug the ethernet cable and try to go wireless. Will not connect to my network. I am also having this problem with all my other devices.
I had everything running fine on a WRT54G, I just wanted to try out the WRT102N. I did change the SSID name form what I was using on the WRT54G.
I'm having an issue where essentially my only course of action is to unplug the router and plug it back in. I can connect my laptop (Dell Inspiron N4010) and my phone (HTC Inspire) once. But then if I put my computer to sleep, or I take my phone out of the wireless range and come back, I cannot connect again. I've gone through and played with the settings (changing the upnp, the beacon intervals, the channel, etc) but to no avail. Invariably, I always have to come back to unplugging and plugging back in.
Also have a Kobo E-Reader and a wireless Canon printer. The whole point of a wireless printer was so that it would stay connected and I can print from my laptop. This router is making this useless.
My mother in law bought my daughter a impression android tablet for Christmas it connects fine at public hotspots but I can not get it to connect to our wrt120n router at home. I have tried everything I know to add it. It asks for the password then says getting IP address then disconnects.
View 2 Replies View Related