I changed the router's IP to 192.168.2.1 due to the same situation as this [URL] linksys and now I can't access my settings I have tried the both pips and nothing and I can't seem to get my linksys wrt54gs v7.2 to let two computers be on the internet at the same time both can be on the network but on one on the internet
View 6 RepliesAfter a successful firmware update to my router I can’t configure wireless settings because the .htm page stays blank if I back the page it comes back to setup page but any config page shows blank with no error message. I’m on a win8 64 iexplorer 10, also tried on a win7 32 IE 8,9,10.
View 1 Replies View RelatedI have a Linksys WRT54GS wireless router. I was trying to get into the set up (using the IP listed in here [URL]) and it asked for a username and password. I have what I thought was the password but no idea what the username was. I tried Administrator and what I had written down as the password but nada. This was originally set up 9 years ago and 3 pc's ago.On the bottom of the router is listed Ownership ID, Device ID, and a serial numb.
View 2 Replies View RelatedI've been having internet connection problems for the last few days and i usually do just unplugging the router and modem and turning it them back on but that hasnt been doing the job this time, its still connecting but it just says no internet access but it will connect when i connect my laptop to the modem. My router is linksys wrt54gs version 6.
View 6 Replies View RelatedI have used the router successfully since purchasing it in April, 2008. The router is connected via cable to the main computer and there are two other computers in the home that are/were used with it. However I noticed that whenever I looked into the available networks in the 'sub' computers it was described as 'unsecured'. I therefore went into the Router [via 192.168.1.1] and amended some settings... forget what they were set at however I changed it to WEP and now shows up as 'secured'.
I now find that I cannot access the internet from the 'sub' [other two wireless] computers and get message 'network did not assign a network address to the computer' if checking 'repair does not restore connectivity... contact network manager. Use the system with Windows XP Professional on Dell Optiplex GX270.
I had an Linksys WRT54GS and this wireless is connected to a switch in an internal enviroment but i want connect guest users without them see my internal network and can't access to any internal server....how can i configure this?
View 1 Replies View RelatedI need to set up a password for my wireless network, but every time I try to access the setup page, the router stops responding. I've gotten as far as it asking for username and password, where I enter admin as the password....and then nothing. The connection times out. I really need to protect my network.
View 1 Replies View RelatedI've looked through the forums and FAQs and haven't seen anything that resolves my issue. I recently moved from the US to Japan. I had my WRT54GS set up in the States and the network worked fine. When i got here, i set it up, hard reset the router and set up a new network.
I can access the internet when connected through the router via ethernet cable, but I cannot connect any of my wireless devices. Easy Link Advisor says "internet connection is not working" but it is. I have two computers connected via cable and they both work so it is not an issue of my ISP allowing multiple IP addresses.
My wireless devices (XBox, PS3, laptop) can see the network but cannot connect through to the internet. I also just noticed that the "wireless mode" according to the EasyLink Advisor says "disable", however the wireless settings on my 192. server webpage is set to "mixed" and seems to be correct in all settings to be on.
I have a wrt54gs v7 and a wap54g v3.1. Both have latest firmware on them. I set the access point to act as a repeater and entered the mac address from the router (It said to use the lan mac address. is that right?). I have them set on same subnet with static ip addresses. They have same wireless ssid and password with one using channel 10 and the other using channel 2. I can receive an ip address from the router and connect to internet. I cannot get an ip address from the access point. I tried a static ip on the computer and it will connect, but I don't have internet. Am I missing something in the setup? Can this access point act as a repeater for this router?
View 3 Replies View RelatedI just purchased an E2500 wireless router. I put the Cisco Connect setup disc in and it could not find my router. With excellent Tech Support, I got it to work. I still do not have any Cisco Connect software on my PC to set passwords or preferences. If I try to run the disc again, it gives me a system critical error and shuts down my computer. How can I get software to access my router settings?
View 1 Replies View RelatedHave a PS3 that will connect to my wrt120n if I unplug the modem and router then plug back in after 2 minutes. if I shut off my PS3 or after approx 1 hour, PS3 drops my connection. I'm trying to access my router page online but after entering the default into my browser, the pop up box will not accept any combo of entries to allow me access. I have an SSID name and my router is password protected. It does not connect me when I use any combo of user name or password or the default "admin".
View 2 Replies View Relatedjust set up my EA6500 in bridge mode, i have the Ethernet cable plugged into the EA6500's yellow WAN port, is that correct, Cisco Article ID: 24583 is not that clear, Cannot also seem to access the EA6500's settings to setup security?
View 2 Replies View RelatedI entered some QoS settings and now when I load the QoS page I get this Javascript error message in Firefox.Error: missing ) after argument list Source File: [URL]. Line: 100, Column: 47 Source Code: QosList[0] = new QosEntry('0','3','0','Kathy's Mac','3', infor);
Basically, the Javascript chokes on any computer name that you enter that has an apostrophe in it. As a result, I don't have access to add or edit any settings on that page. Seems like a major rookie mistake, especially for a major network device manufacture.
I installed an IP camera, and had to change my E1000 router settings to a static IP address. Now I can't access the router settings. 192.168.1.1 is still the default gateway, but it won't open in any browser.
I'm reluctant to do a reset because it took me quite a while to figure out how to get the IP camera and port forwarding working (it does!), and I'd hate to do it all again and come to the same place. I'm not very good at this stuff, and it's a small miracle that I did it once.
I have a Linksys WRT54GS router that I have installed dd-wrt on.My household is overloaded with wireless devices, and living in a home of 6, speeds for everyone seem to slow down drastically later at night when everyone is simultaneously connected and streaming media -- whether it be Netflix, YouTube, etc.. My typical speed wired to the router with no other connections is around 25 mb/s down and 1-2 mb/s up.Obviously, it's going to slow to a crawl when we have an iPad, 3 iPod touches, an iPhone, a Wii (playing Netflix) and 4 PCs all connected simultaneously.What I need to do is give my personal computer priority and throttle all other devices. So that I myself will have decent speeds while hampering all of the other household connections. I rely on those speeds for my job and that should have priority over my brother watching music videos on YouTube.
View 1 Replies View RelatedEverything was working fine. Changed Nothing on the router. Goes out and now wont broadcast a wireless signal, cant manually reset the router, or get into the settings with 192.168.1.1
Currently I am wired through it with my desktop and its working, but not much else.
I have a wrt54g Linksys router, and recently whenever I type 192.168.1.1 into the internet in order to access the settings/homepage, I get " internet cannot display this webpage"
View 2 Replies View RelatedI lost my installation CD and now I moved to a new place. I have linksys wireless-G router model-wrt54gs. how can i setup a new wireless now?
View 5 Replies View RelatedI have a Wireless-G broadband router WRT54GS and have figured out how to enable logging.This gives me the IP addresses, but I would like to be able to easily see the FQDN so I can see what my kids are looking at on the web.Is there a way to get that information via the built in logging feature?If not is there a way to take the log file and run this through sometype of program that will generate the FQDN's?
View 2 Replies View RelatedSometimes the PC does not acquire the dns etc from the router and I have to manually enter in each PC to restore internet. - only W7.
View 2 Replies View Relatedhow do i uninstall my linksys WRT54GS router? i just bought a netgear and i want to uninstall my wrt54gs router
View 9 Replies View RelatedI have a 2wire modem connected to the Internet port of my WRT54GS which is connected to a D link DSS 16+ Fast Ethernet switch. Without the switch, I can connect wired and wirelessly to my WRT54GS. However, when I put connect my any port of my D link switch to ports 1 - 5 of WRT54GS, I loose internet all together either wired/wireless to the router or wired to the D-link switch.I wonder why the IP Address will change as I understand that the switch is just a pass through switch.
View 1 Replies View RelatedI'm having a very difficult time getting my WRT54GS to work with my Westell 6100 modem. I've been bouncing around gathering info, and what I've learned is that the goofy way CenturyLink tech support told me to hook up my old wired router (modem line into outgoing (LAN) router port) is because the Westell 6100 is a "smart modem/router". Therefore, when I run the Linksys setup CD, it sees the modem as a router, and won't properly configure. I've also learned that the Westell modem can be "dumbed down" into simply a modem by putting it into "bridge mode", which is where I'm at right now - trying to get it reset to factory defaults and resetting the connection type from PPPoE to Bridge. In the meantime, I also reset the WRT54GS to factory defaults, and now I've got another problem: the router will not allow me to set up encryption. The default setting is "Disabled", and when I click the down arrow and try to make any selection at all (preferred selection is WPA2 Personal), it reverts to Disabled. I've also tried to change the router's IP address to 192.168.2.1 (and alternately to 192.168.1.253), so it won't conflict with the modem's IP, and it freezes up every time I try.
View 1 Replies View Relatedi have been using a WRT54GS LINKSYS ROUTER for 2.5 years problem free until now. All of a sudden i cant connect to the internet through it at all. when i diconnect it and hook my desktop directly to the modem it works but i need the wireless to use my laptop. I have tried everything to get it working again, no dice. when using w7 diag tool it reports back local area connection doesnt have a valid ip config.
View 3 Replies View RelatedI have a WRT54GS v. 7.0 w/ the latest firmware. Im looking for ways to optimize the router for best performance.There are 4-5 iphones/ipads that will connect to it. 3-5 laptopsand one xboxNo wired connections.Im using COX internet on the west coast which provides good internet service. Im not an expert with networks or routers but i follow instructions real well. What can i do to my stock/default router to take 100% advantage of its capabilities?
View 2 Replies View RelatedI would like to upgrade the firmware for my WRT54GS V2.1 router however, I only see versions 1.0, 1.1, 2.0, 3.0, etc.. There is no 2.1 listed, so does this mean I can use the v2.0 firmware?
View 3 Replies View RelatedFactory default settings of my WRT54GS encryption are Disabled. When I try to enable WPA Personal encryption (>Wireless, Wireless Security), it reverts back to Disabled as soon as I make the selection. >Administration, >Wireless, >Encryption Function is Disabled.When I had this router set up at another location with another ISP, this was never an issue. How do I get the encryption function to be enabled?
View 4 Replies View RelatedI successfully cascaded a WRT54gs V6 router to a LinksKey wired router LAN to LAN. My concern is I get a warning on my one computer saying it is an unsecured connection. I have not seen a way to go in and make any kind of security settings. Most of the files on my main computer which is connected via the wired router are labeled as private files.
View 9 Replies View RelatedCurrently I have Verizon DSL and which supplied me with a Westell 7500 modem/wireless router. I am also connecting a Linksys WRT54GS (firmware Version: 7.2.08) to the Westell 7500.
When I connect via cable or wireless to Linksys WRT54GS I am not able to establish VPN connection. I get the error “Error 619: A connection to the remote computer could not be established. So the port used for this connection was closed”.
However, when I connect via cable or wireless to Westell 7500 I am able to connect to VPN.
I tried resetting the Linksys WRT54GS to factory settings and reconfigured but no success to VPN.
At work we have a Windows 2003 setup with VPN Role on it and on my laptop I am using the built in VPN connection within Windows 7.
So the power light on my WRT54GS router is off but my LAN lights 1-4 and the WLAN light stay on when power is attached but no cables are in the ports.
View 4 Replies View RelatedI need to reinstall my WRT54GS but can't find the original disk. Is there someplace I can d/l the install software? I can find the firmware updates but I think I need more than that to install the router.
View 8 Replies View RelatedI just got a new modem and was also hoping to boost the speed of my router without buying a new one. Are there any ways to increase the speed of the modem i already have?
View 2 Replies View RelatedI have a WRT54GS v1 router which is currently loaded with firmware version 2.07.1. I want to upgrade it with the latest firmware. Where I can find the latest firmware download for this model router? Linksys does not have it available on their site.
View 2 Replies View Related