Cisco Switching/Routing :: Configuring NAT On 1920 Router With Dual WAN (ADSL)
Jun 7, 2013
Basically I have a simple LAN of 30 users and 2 servers that sit on a private address range (192.168.1.1 - 254). I have a Cisco 1921 router with 2 Gigabit Ethnet interfaces and have installed a 2 port Ethernet module to expand interfaces,I have Two Internet providers that provide me an Optic connection to a converter and then a CAT 5 cable. On both of these connections have private public assigned IP addresses.I have a email server and webserver on the LAN (192.168.2 and 192.168.1.3) and with to port forward various ports to these servers - 25, 80, 443 3389, and 2222.
In my external DNS I have two MX records for the mail server (mail.globalhomegroup.com) that point to 2 A records - one record for the publicly assigned IP address of one ISP and another IP address for the other ISP. Ideally what i would like is for mail to be delivered to the first ISP Ip address - the one with the lower MX weighting and then if that line goes down, through the IP address of the second MX record - the backup ISP we are using.
So I guess I am port forwarding to the inetrnal server IP addresses via one of the two external interfaces.At the same time I need to allow internal users to access HTTP, HTTPS etc.So I have managed somehow to configure the external interfaces of the routers to connect to the ISPs and have managed to assign IP info to intenral LAN interface. I can telnet to the router from the Internet via Dialer0 or Dialer1. Other than that I am totally stuck - I have tried to configure and debug NAT etc but cant see wood for the trees now. Basically the port forwarding is not working and i am not sure if the config I have done is in anyway correct.
View 10 Replies
ADVERTISEMENT
Jan 10, 2013
We have 2 router cisco 2621XM and want to configure a VPN between them, but first we want to configure ADSL in both with the card installed.
View 2 Replies
View Related
Mar 24, 2013
I need to configure configuring pppoe ADSL on cisco 887VG
View 5 Replies
View Related
Jan 31, 2012
In a site we currently have 1 BT provided ADSL link which is currently terminated using their device which I believe is some kind of 2wire device, which is extremely slow due to distance from the Exchange (4Mbps)...We have a growing number of users here and want to install a second ADSL line from BT to give them increased performance.
We have a Cisco 2800 sat not doing much so I was wondering if I could use this to load balance the link? I know BT do not support MPPP so therefore the maximum any user can get will be the speed of a single link (4Mbps)...But basically how can this be done..
Can I leave the two BT routers in place and place the Cisco 2800 behind them, or do I need to purchase two ADSL modules for the 2800 and terminate the connection there?Also once done, what do I need to do regarding actually setting up the load balancing? I have seen this:
[URL]
But am unsure as to how relevant it is? I am not sure I understand what the ACL's are being used for? I just want all users on the LAN to load balance out...
Also I am unsure of this statement:You potentially need to add policy-based routing for specific traffic to ensure that it always uses one ISP connection. Examples of traffic that require this behavior include IPSec VPN clients, VoIP handsets, and any other traffic that use only one of the ISP-connection options to prefer the same IP address, higher speed, or lower latency on the connection.I do not understand why a established session such as a VPN client, would ever traverse the second ISP connection anyway?
View 2 Replies
View Related
Feb 19, 2012
I would like to make a design with 4 Nexus 5596UP. 2 of them equipped with Layer 3 Expansion Module so they can serve as core layer and the other 2 Nexus used as Layer 2 for aggregation server layer.The 2 Nexus in the core layer will run HSRP and will peer with ISP via BGP for Internet connection The 2 Nexus in the aggregation layer will be configured as layer 2 device and have FEX and switches connected to them.What I am ensure of is how the vpc and port-channel configuration should look like between the 4 nexus. What I was thinking is to run vpc between the 2 Nexus in the aggregation layer and between the 2 Nexus in the core layer. Than I was thinking of connecting each Nexus in the aggragtion layer to both Nexus in the core layer using port-channel and vice-versa.
View 3 Replies
View Related
Dec 5, 2011
i want to use the cisco 2901 router with two adsl cards(EHWIC-VA-DSL-B) and would like to know if that possible without any restrictions with the ip base license.
View 2 Replies
View Related
Jan 23, 2012
We currently have a main network running through a static broadband connecting using a Cisco 1700 ADSL router, everything is working fine locally.
We are looking to rent some space in an office nearby so im going to order another business adsl connection with static IP for this site and i currently have a spare 1800 router.My question is can the cisco routers connect up like a VPN connection so both sites work together and will the connection remain online constantly so from the remote office we can access all our servers from the main network?
Also how does the IP addressing work on 2 sites. The main network uses 10.120.21.x and DHCP is assigned from a cisco router. Does the remote network assign from the same DHCP server or would the remote sites cisco router need to be setup to give out DHCP to local machines. If so what would be the best IP setup to use.
View 9 Replies
View Related
Nov 9, 2012
I've moved a Cisco 887 router from a site where it was used to dial up on an ADSL line to a new site where we have a EFM circuit which terminates at a Cisco 1841 router managed by our ISP. I therefore need to re-configure our 887 router to work as a conduit from our servers back to the Cisco 1841 as its gateway.
I have asked from our ISP and they told me that i need to configure the 887 to use IP address 176.35.140.65 255.255.255.248 and its gateway should be 176.35.140.70. That's great advice in theory but I don't know how to configure this correctly
Our internal network is using subnet 192.168.42.XX which will need to be retained for local devices.
View 7 Replies
View Related
Feb 16, 2013
I would like to ask if there are dual WAN router models on ISR G2. The client doesn't want the RV042G. Any model from the 890 series up to the 2900 series ISR G2 routers? The connection from the ISP is via Ethernet. If a serial connection would be used then we can just add an HWIC-2T for this matter.
View 10 Replies
View Related
Dec 9, 2011
Will 2811 Router with 4 switch port module, How to do dual ISP configuration on this router.
View 10 Replies
View Related
Mar 17, 2013
I've 3 interfaces on router:
Gb0/0-ISP01 with DHCP client
Gb0/1-ISP02 Static IP 192.168.2.x/24
Fa0/0 - LAN 192.168.1.1/24
I want to know, how to configure:1. Set the IP of interface Gb0/0 as dhcp client from ISP01 and make it as default route.
2. How to configure the ip nat.....overload?
3. How to use the ip sla to monitor internet connectivity to 8.8.8.8 for ISP01, if it fails, to go to ISP02.
View 3 Replies
View Related
May 10, 2011
I have a CISCO 1841 with a HWIC interface to my ISP. I want to make a ADSL connection and my current running-file is: [code] The problem I have is that the ISP connection is established but then goes down.
View 1 Replies
View Related
Feb 12, 2013
I am configuring DHCP pool for voice vlan on cisco 2921 router.
Here is the setup.
2921 router -> 3750 -> 2960 PoE -> 7942 IP Phone
Router Config
ip dhcp excluded-address 10.146.54.1 10.146.89.50
!
ip dhcp pool VoiceVlan
network 10.146.54.0 255.255.255.0
subnet prefix-length 24
dns-server 10.144.68.32 10.144.68.33
option 150 ip 10.146.68.36
default-router 10.146.54.1
netbios-name-server 10.144.68.32 10.144.68.33
netbios-node-type h-node
[code]....
View 1 Replies
View Related
Mar 28, 2011
We have purchased a Cisco 1921 with twin ADSL after advice from a Cisco sales rep. However I am having trouble working out the load balancing/fail over config for the device.
I would like traffic to balance over both ADSL lines and if one goes down not to interrupt connectivity.
I had a look at ppp multilink but I am unsure our ISP (BT) support this?
!! Last configuration change at 13:18:34 UTC Tue Mar 29 2011!version 15.0service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname xxxxxx
[Code]......
View 10 Replies
View Related
Mar 26, 2009
Does Cisco MSE 3350 comes with two NICs. I want to configure them as a team bound to one IP address and send each to a separate 6509 switchport all in the name of redundancy and failover.
View 2 Replies
View Related
Jan 12, 2013
1. We have Two 3900 Router on the core layer which are terminated with one ISP on one Router and Secondary ISP on Second Router.
2. Can we configure my ASA 5520 with Active/Standby termenating two IPS providers one on Active ASA 5520 and Other ISP on Standby ASA 5520, so that when Active ISP fail ASA Secondary can become Active and send the Traffic throough Secandary ISP.
3. The reasion behind giveing Public IP on Firewall is to Terminate VPN on our Firewall i.e. SSL and IPSEC VPN.
Few Clarification If we can achive the above:
1. How will the DMZ Servicec nated with my Primary ISP on my Primary ASA will be routed when the Secondary ASA is acting as Active Firewall.
2. Can Web SSL and Client To Site IPSEC VPN users access service via the Secondary ISP- ASA when my Primary ASA and ISP is down.
View 7 Replies
View Related
Mar 17, 2013
I bought a RV042G router some days ago to manage 2 adsl lines at my home. Everything works correctly except one thing : i can't configure the bandwidth management. When i go to "Bandwidth Management" menu, then "Bandwidth Management Type" then i choose rate control or priority and i a had some rules to priorize http protocol for example, then i click on save button. After a few seconds of internet usage i loss connectivity to the router and internet and 192.168.1.1 became unreachable to ping. I had to unplung the power cord to restart the router, the same problem still occurs until i remove all the rules ! Some times i even had to do a factory reset because my adsl modems are unreachable behind the router (unable to ping the gateway).
View 4 Replies
View Related
Aug 5, 2012
I'm trying to configure intervlan routing between a cisco 2801 router and HP/Amer switches. Using int fa0/1 and subinterfaces I was sure I had it configured correctly, but I cannot ping the default gateways when I place a host in a particular vlan. Below is what I have configured.
HP switch - port 9 connects to fa0/1 on 2801
ip default-gateway 10.1.100.1
trunk 9 Trk1 trunk
trunk 10 Trk2 trunk - to another switch
[code].....
View 4 Replies
View Related
Dec 12, 2010
I have a SR520W-ADSL-K9, I´m trying to setup it trough CCA, but I have some troubles. At the internet connection I mark PPoE option, enter the vci=0, vpi=35, the username, the password (like the ISP TELMEX suggest), and mark the IP Negotiated option, but I have not find the ISP service give me an IP Address and establish the connection.
View 6 Replies
View Related
Apr 25, 2012
I have 3 877 ADSL routers for internet connectivity. I recently installed a FW behind them and would like to use the Ciscos as load balance in order to get better utilization from my 3 internet links.
1) the 3 routers are on DHCP from the ISP on the WAN side.
2) the 3 ciscos are on the same class C subnet on the LAN side: 10.201.1.252, 10.201.1.253 and 10.201.1.254
View 3 Replies
View Related
Mar 24, 2013
to configure this router my main objective is ADSL connection, and wireless network setup.
[code]...
View 8 Replies
View Related
Feb 26, 2012
i'm looking for a cisco 881 configuration with SDSL line as nominal and ADSL as backup.
View 9 Replies
View Related
Apr 24, 2012
I have cisco 1801W . Earlier I am using ADSL dynamic IP address on RJ 11 through the ADSL Port but now the ISP change the connection to RJ45.
I am trying to configure it but unable to do this. ADSL line is okay because When I am connecting through the ISP router it is working fine. I have connected the ADSL RJ45 cable in the router fast ethernet 0.But I wanted to use Cisco 1801 Router so that I can use the ADSL as primary and ISDN as the backup.
Below is my configuration, eiteher this is possible to configure ADSL through RJ45 in 1801 and what configuration require for this.
Router#show ip int brief
Interface IP-Address OK? Method Status Protocol
FastEthernet0 unassigned YES DHCP up up
BRI0 unassigned YES unset administratively down down
BRI0:1 unassigned YES unset administratively down down
BRI0:2 unassigned YES unset administratively down down
[code].....
View 2 Replies
View Related
Jun 10, 2012
I am working on a network which has two ISP connections (Active/Active) terminating on router (ASR1000). From the LAN side (6500 switch) all the traffic need to be route on ISP1 but some of the specific subnets like 10.250.0.0/16 need to be route on ISP2 connection.
I am planning to use PBR and NAT with route maps. any documents or refrences are provided.
(access switches)---------(core switch)----------(routers)----------------(ISP1)
----------------------(ISP2)
View 1 Replies
View Related
Jan 1, 2013
I have a Cisco 1721 router with an ADSL wic. I have followed guides on the Cisco website so that I can connect the router to my home adsl connection. The router connects to my broadband provider and sucesfully obtains an IP address along with Dynamically assigned DNS servers. I am able to ping google.co.uk from the router but not from clients attached via DHCP.
I have noticed that if I ping the IP address of google.co.uk from a client it resolves but it will not resolve the name. This would lead me to believe that the problem lies with DNS resolution/forwarding but I do not know how to investigate further.
View 3 Replies
View Related
Aug 22, 2012
I have the requirement to provide a Cisco Router with 3 x ADSL lines (768k) to increase the internet speed.PPP multilink is not supported from the ISP.
Is it possbile to distribute the traffic between this three ADSL lines?How can I configure this?
I have the following hardware configuration:
1 x CISCO1921-SEC/K9
2 x EHWIC-VA-DSL-B
The third ADSL line is connected over an ADSL modem at one fixed Router Gigabit interface.
View 0 Replies
View Related
Jan 19, 2012
Is the ADSL line interface on Cisco 877W not initialising a known issue? This interface on my router has been in this state for more than one month, with the rest of the router seemingly operational. The interface was connected directly to my ADSL broadband and worked well for two years. But then, about a month ago, the interface went down. I saw the exact moment this happened recorded as a syslog message. The only information was that the interface status had changed to down.
Initially I thought this was a matter of reload the router and all will be well. Did not happen. Then I thought my broadband connection was to blame. However, this option was quickly ruled out. So I went on to exhaust all troubleshooting options, including reflashing the router with the saved image and totally changing the configuration. Still no change. I have had to go back to my old BT home hub for internet access. In terms of speed this actually works a lot better than the Cisco router. But I would still rather have the router connected to my broadband line. What can I do to bring the ADSL interface back to life?
View 3 Replies
View Related
Jun 1, 2013
Configuring an application using routing mode on cisco ace clients ---asa--3750--cisco ace--- servers behind vip,visa card transaction servers.i am able to setup a vip on ace using routing mode on ACE,as the servers need to see the client ip ,so we are not performing SNAT,this part is working fine,when a request comes from the client ,it goes to the vip and to one of the backend servers ,and the request will be forwaded back to the ace ,as the default gateway on the servers is pointing to the server vlan on ace.but if the transaction from the servers need to go to the visa card transaction servers ,how can we achieve this ,and after fetching the data from visa servers,does the reply will be fwd to the ACE or ASAs directly.
View 1 Replies
View Related
May 25, 2012
I currently have a Cisco 891 running with a FTP running on port 21. I currently have the NAT from external IP to and internal IP 192.168.12.6 for port 21. And the firewall allowing that traffic through and client software is working fine. However I need this FTP to be running on port 990 and anytime I change the NAT and the firewall, the external FTP clients connect but then drop when recieving the directory listing.
View 10 Replies
View Related
Feb 21, 2013
I have IP phones connected to 2960 i want to segregate traffic traffic comming from IP phones which has a COS value of 5 and want to allocate a band width of 200 MBPS for those traffic .
Can any one share sample QOS configuration for achiving this in 2960 ?
View 2 Replies
View Related
Aug 24, 2012
i have a problem with my adsl line connected on a HWIC-ADSL on router 2901 it was working good until yesterday the atm interface is down but the interface dialer is up .i connected this line into home adsl modem and the line is working good?
View 2 Replies
View Related
Jun 10, 2013
We think we have configured the ACE and Tacacs properly as we auth, but are not able to enter into configuration mode.
ACE-4710 A4(2.3)
View 1 Replies
View Related
Aug 4, 2012
I'm configuring VSS with two Sup2T but the Sup2T of the standby not coming active
View 6 Replies
View Related
