Cisco Switching/Routing :: 887VA / WLAN - Set Up ADSL Connection
Mar 24, 2013to configure this router my main objective is ADSL connection, and wireless network setup.
[code]...
ADVERTISEMENT
Cisco WAN :: 887VA Adsl Connection Up But Only Certain Websites Reachable?
Feb 14, 2013The aDSL circuit is up and connected and I can reach the internet, however not all sites on the internet are reachable. This is occurring on two seperate 887VA’s and the circuit has been tested with a netgear router and no issues occur. The router has been tried on 5 different ADSL connections and the same problem occurs although more websites can be reached on a home broadband connection (ADSL2+ Annex A) as opposed to the problem being more severe on an ADSL2+ Annex M circuit. The problem seems to affect websites that are full of adverts more than sites that have single domain landing pages.
The sites that I cannot reach are pingable. This happens on multiple machines behind the router. The same config is used on an cisco 877-M router with no issues.
! Last configuration change at 14:52:30 UTC Wed Feb 13 2013
version 15.2
no service pad
[Code].....
Cisco WAN :: 887VA - How To Change Adsl Mode
Jun 13, 2012In 12.x I used to go under atm0 and used ' dsl operating-mode' How can I do it under 887VA running 15.2?
View 1 Replies View RelatedCisco WAN :: 887VA PPPoA BT ADSL Setup?
Feb 29, 2012Im new to Cisco equipment and weve just upgraded to a all singing 8000 series (887VA) to be precise.
i'm having difficultys in setting the router to connect to our BT ADSL2 business broadband, we have a static IP but on normal cheaper routers you just input a Chap username and password. and the router sorts the rest.
i've followed the tech support from cisco website inputted the configure commands to create the ATM0 and a Dialer0 but still having no joy.when you log into the gui it only shows you a enable PPPoE tick box. no signs of PPPoA?
Cisco Switching/Routing :: SR520 ADSL Connection With PPoE?
Dec 12, 2010I have a SR520W-ADSL-K9, I´m trying to setup it trough CCA, but I have some troubles. At the internet connection I mark PPoE option, enter the vci=0, vpi=35, the username, the password (like the ISP TELMEX suggest), and mark the IP Negotiated option, but I have not find the ISP service give me an IP Address and establish the connection.
View 6 Replies View RelatedCisco WAN :: Unable To Connect 887VA Router To ISP Via ADSL
Jul 7, 2011I have been trying to connect a new Cisco 887VA Router to the Internet using ADSL via PPPoE and have been unsuccessful. The DSL line is active and functioning correctly since the current "old" router is connected and working without any problems (the "old" DLink router is connected to an Alcatel DSL Modem). AT&T provides the ADSL service to the office. When the Cisco Router is connected it tries to negotiate a connection via PPPoE on the WAN interface but utlimately fails. The IP for the WAN interface is dynamic.
Below is the current configuration of the router.
!
! Last configuration change at 00:43:54 UTC Sun Jun 26 2011
!
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
[code]....
Cisco WAN :: 887VA ADSL Over Pots Router And PPPoE With Dynamic IP?
Feb 11, 2012I've got problem trying to connect the CISCO-887VDSL/ADSL OVER POTS ROUTER to internet. Only got the LAN part working.I'm trying to setup PPPoE with dynamic IP Followed CISCO's documentations but the commands used were not recognized by the router.
here's my config.
!
! Last configuration change at 08:31:51 UTC Sat Feb 11 2012
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[code]....
Cisco WAN :: 887VA ADSL - Service Policy Brings Down Link?
Aug 7, 2012Have installed an 887VA on the end of a ADSL connection. The provider has specified EF 150 on the link. The router is configured using a Virtual Template.
If the Virtual Template has a service policy applied, we don't have connectivity to their main site - although the CD and PPP lights are lit. As soon as the service policy is removed, we have connectivity.
We've had three sites with the same problem. Two of the sites don't have QoS specified on the link but had the same problem if the service policy was applied.
Hardware - CISCO887VA-SEC-K9
Software - 15.1(4)M4
=== config snippets
class-map match-all Voicematch access-group 10
policy-map Dscpclass Voice priority 150class class-default
interface ATM0
bandwidth 1143
bandwidth receive 12334
[code]....
Cisco Switching/Routing :: Using ASA-5510 To Route VLAN WLAN Connection
May 28, 2012I am a complete newbie to Cisco equipment. So far I've been able to figure out how to do most of what I needed by using the ASDM but I have run into something that is a little more complicated that just opening a port. We currently have a connection to our remote site. This site has a T1 internet connection. Our connection is a site to site VPN with an ASA-5510 on this end and a ASA-5505 on the other.
We are upgrading this connection to a 75mbit hybrid microwave/fiber link. The provider is going to hand it off to us as an untagged VLAN. We made the decision to route all of the remote site's internet access through this location as to avoid having to split off part of the bandwidth of this link to dedicate to internet access.........
Cisco WAN :: Poor Performance / Packet Loss With 887VA Router On ADSL Line
Dec 6, 2012We have a remote site connected to ADSL line with a Cisco 887VA router attached. This has been working fine for the last couple of months. However, recently, the site have started to complain of performance issues (network slow, applications disconnecting, etc)Looking on the router, we can see evidence of packet loss/timeouts from a simple ping to the internet e.g. [code]
However, we have logged the fault with our service provider and they return all line tests as clear but what is particularly strange is that they also report “and the SNR Margins are well within threshold levels (Upstream 11.5 and Downstream 15.0)” which, unless I’m misunderstanding something, seems to be completely different from what the router itself is reporting.Is there a reason why the service provider’s stats for Noise Margin would appear to be so different from what the router is reporting?
Cisco Switching/Routing :: Possible To Use Inbuilt 4 Port Switch On 887VA
Jul 16, 2012Is it possible to use the inbuilt 4 port switch on a Cisco 887VA ADSL router for inter Vlan routing? My plan is to configure port FA0 - 2 as Vlan 1 (default) 192.168.0.254/24 and port FA3 as Vlan 2 192.168.4.254/30. My SIP server will sit on Vlan 2 192.168.4.253/30 however remote Wan users coming through other Cisco 888 routers connected to the 887 will need to access Vlan 2 from Vlan 1, is this possible?
View 12 Replies View RelatedCisco Switching/Routing :: 887VA Using Dual Ethernet Ports For Aggregation
Jun 6, 2013We are running a Cisco 887VA router for our internet access but of course the port connected to the internal network only supports 100Mbit/s. There are a few 100Mbit/s ports on the router; I was wondering whether it was possible to use more than one port to provide aggregation to get higher speed such as two ports providing 200Mbit/s? We are running Gigabit internal.
View 4 Replies View RelatedCisco WAN :: Difference Between 887VA-K9 And 887VA-SEC-K9
Aug 30, 2012difference of CISCO887VA-K9 and CISCO887VA-SEC-K9.I thought it because of the Advanced Security and Advanced IP Licenses, but it isn't, I've got the -SEC- Version now just with the Advanced Security license. So I asking myself why I bought the more expensive CISCO887VA-SEC-K9 if I have to buy the additional Advanced IP Services licenses extra..
View 14 Replies View RelatedCisco WAN :: To Configure 887VA For A PPPoe ADSL2 Connection
Mar 27, 2012I'm trying to configure an 887VA for a pppoe ADSL2+ connection with no luck.I know the ISP requires pppoe (LLC), and the pvc is 8/35.
The CD light is on, and the line is up, but the 887 just won't connect
Cisco WAN :: How To Get 887va Working On Eircom ADSL2 Connection
Jul 16, 2012I am new to the Cisco routers but am trying to get a Cisco 887va working on a Eircom ADSL2 connection.
I was using the config of an old Cisco router as a guide, basically this has encapsulation aal5snap under the ATM interface, I am unable to set this in the 887va, I did read that this needs to be set under the VDSL controller however it will not take the commands. Also how can I set the the dsl operating-mode to auto.
Here is my config
Building configuration...
Current configuration : 1958 bytes!! Last configuration change at 13:20:03 UTC Tue Jul 17 2012version 15.1no service [code]...
Cisco Switching/Routing :: Load Balance Between 3 877 ADSL Routers
Apr 25, 2012I have 3 877 ADSL routers for internet connectivity. I recently installed a FW behind them and would like to use the Ciscos as load balance in order to get better utilization from my 3 internet links.
1) the 3 routers are on DHCP from the ISP on the WAN side.
2) the 3 ciscos are on the same class C subnet on the LAN side: 10.201.1.252, 10.201.1.253 and 10.201.1.254
Cisco Switching/Routing :: 881 SDSL With ADSL Backup Configuration?
Feb 26, 2012i'm looking for a cisco 881 configuration with SDSL line as nominal and ADSL as backup.
View 9 Replies View RelatedCisco Switching/Routing :: Configuring ADSL In Router 2621XM
Jan 10, 2013We have 2 router cisco 2621XM and want to configure a VPN between them, but first we want to configure ADSL in both with the card installed.
View 2 Replies View RelatedCisco Switching/Routing :: Configuring PPPOE ADSL On 887VG
Mar 24, 2013I need to configure configuring pppoe ADSL on cisco 887VG
View 5 Replies View RelatedCisco Switching/Routing :: ADSL On Fast Ethernet In 1801?
Apr 24, 2012I have cisco 1801W . Earlier I am using ADSL dynamic IP address on RJ 11 through the ADSL Port but now the ISP change the connection to RJ45.
I am trying to configure it but unable to do this. ADSL line is okay because When I am connecting through the ISP router it is working fine. I have connected the ADSL RJ45 cable in the router fast ethernet 0.But I wanted to use Cisco 1801 Router so that I can use the ADSL as primary and ISDN as the backup.
Below is my configuration, eiteher this is possible to configure ADSL through RJ45 in 1801 and what configuration require for this.
Router#show ip int brief
Interface IP-Address OK? Method Status Protocol
FastEthernet0 unassigned YES DHCP up up
BRI0 unassigned YES unset administratively down down
BRI0:1 unassigned YES unset administratively down down
BRI0:2 unassigned YES unset administratively down down
[code].....
Cisco Switching/Routing :: Use 2901 Router With Two ADSL Cards
Dec 5, 2011i want to use the cisco 2901 router with two adsl cards(EHWIC-VA-DSL-B) and would like to know if that possible without any restrictions with the ip base license.
View 2 Replies View RelatedCisco Switching/Routing :: 1941 - Configuration Of WLAN AP
Apr 5, 2013I have a Cisco router 1941 connected to a switch. I'm configuring the w LAN- AP and i need to have the wireless devices have an ip in the same range of the wired devices.Since i cant use the same ip range on the gig0/1 and the V LAN 1 for the wireless, i wanted to know how to config the giga0/1 connected to the switch to act as a layer 2 port and i keep the ip on the v LAN 1.
View 9 Replies View RelatedCisco Switching/Routing :: Configuring NAT On 1920 Router With Dual WAN (ADSL)
Jun 7, 2013Basically I have a simple LAN of 30 users and 2 servers that sit on a private address range (192.168.1.1 - 254). I have a Cisco 1921 router with 2 Gigabit Ethnet interfaces and have installed a 2 port Ethernet module to expand interfaces,I have Two Internet providers that provide me an Optic connection to a converter and then a CAT 5 cable. On both of these connections have private public assigned IP addresses.I have a email server and webserver on the LAN (192.168.2 and 192.168.1.3) and with to port forward various ports to these servers - 25, 80, 443 3389, and 2222.
In my external DNS I have two MX records for the mail server (mail.globalhomegroup.com) that point to 2 A records - one record for the publicly assigned IP address of one ISP and another IP address for the other ISP. Ideally what i would like is for mail to be delivered to the first ISP Ip address - the one with the lower MX weighting and then if that line goes down, through the IP address of the second MX record - the backup ISP we are using.
So I guess I am port forwarding to the inetrnal server IP addresses via one of the two external interfaces.At the same time I need to allow internal users to access HTTP, HTTPS etc.So I have managed somehow to configure the external interfaces of the routers to connect to the ISPs and have managed to assign IP info to intenral LAN interface. I can telnet to the router from the Internet via Dialer0 or Dialer1. Other than that I am totally stuck - I have tried to configure and debug NAT etc but cant see wood for the trees now. Basically the port forwarding is not working and i am not sure if the config I have done is in anyway correct.
Cisco Switching/Routing :: 1721 With ADSL - Clients Unable To Resolve DNS
Jan 1, 2013I have a Cisco 1721 router with an ADSL wic. I have followed guides on the Cisco website so that I can connect the router to my home adsl connection. The router connects to my broadband provider and sucesfully obtains an IP address along with Dynamically assigned DNS servers. I am able to ping google.co.uk from the router but not from clients attached via DHCP.
I have noticed that if I ping the IP address of google.co.uk from a client it resolves but it will not resolve the name. This would lead me to believe that the problem lies with DNS resolution/forwarding but I do not know how to investigate further.
Cisco Switching/Routing :: 1921 Load Balancing Over 3 ADSL Lines
Aug 22, 2012I have the requirement to provide a Cisco Router with 3 x ADSL lines (768k) to increase the internet speed.PPP multilink is not supported from the ISP.
Is it possbile to distribute the traffic between this three ADSL lines?How can I configure this?
I have the following hardware configuration:
1 x CISCO1921-SEC/K9
2 x EHWIC-VA-DSL-B
The third ADSL line is connected over an ADSL modem at one fixed Router Gigabit interface.
Cisco Switching/Routing :: 877W ADSL Line Interface Not Initializing?
Jan 19, 2012Is the ADSL line interface on Cisco 877W not initialising a known issue? This interface on my router has been in this state for more than one month, with the rest of the router seemingly operational. The interface was connected directly to my ADSL broadband and worked well for two years. But then, about a month ago, the interface went down. I saw the exact moment this happened recorded as a syslog message. The only information was that the interface status had changed to down.
Initially I thought this was a matter of reload the router and all will be well. Did not happen. Then I thought my broadband connection was to blame. However, this option was quickly ruled out. So I went on to exhaust all troubleshooting options, including reflashing the router with the saved image and totally changing the configuration. Still no change. I have had to go back to my old BT home hub for internet access. In terms of speed this actually works a lot better than the Cisco router. But I would still rather have the router connected to my broadband line. What can I do to bring the ADSL interface back to life?
Cisco Switching/Routing :: 1700 ADSL Router - Connecting 2 Sites Together
Jan 23, 2012We currently have a main network running through a static broadband connecting using a Cisco 1700 ADSL router, everything is working fine locally.
We are looking to rent some space in an office nearby so im going to order another business adsl connection with static IP for this site and i currently have a spare 1800 router.My question is can the cisco routers connect up like a VPN connection so both sites work together and will the connection remain online constantly so from the remote office we can access all our servers from the main network?
Also how does the IP addressing work on 2 sites. The main network uses 10.120.21.x and DHCP is assigned from a cisco router. Does the remote network assign from the same DHCP server or would the remote sites cisco router need to be setup to give out DHCP to local machines. If so what would be the best IP setup to use.
Cisco Switching/Routing :: 2800 Series - Dual ADSL Links?
Jan 31, 2012In a site we currently have 1 BT provided ADSL link which is currently terminated using their device which I believe is some kind of 2wire device, which is extremely slow due to distance from the Exchange (4Mbps)...We have a growing number of users here and want to install a second ADSL line from BT to give them increased performance.
We have a Cisco 2800 sat not doing much so I was wondering if I could use this to load balance the link? I know BT do not support MPPP so therefore the maximum any user can get will be the speed of a single link (4Mbps)...But basically how can this be done..
Can I leave the two BT routers in place and place the Cisco 2800 behind them, or do I need to purchase two ADSL modules for the 2800 and terminate the connection there?Also once done, what do I need to do regarding actually setting up the load balancing? I have seen this:
[URL]
But am unsure as to how relevant it is? I am not sure I understand what the ACL's are being used for? I just want all users on the LAN to load balance out...
Also I am unsure of this statement:You potentially need to add policy-based routing for specific traffic to ensure that it always uses one ISP connection. Examples of traffic that require this behavior include IPSec VPN clients, VoIP handsets, and any other traffic that use only one of the ISP-connection options to prefer the same IP address, higher speed, or lower latency on the connection.I do not understand why a established session such as a VPN client, would ever traverse the second ISP connection anyway?
Cisco Switching/Routing :: 887 Router / 1841 - Dial Up On ADSL Line To New Site
Nov 9, 2012I've moved a Cisco 887 router from a site where it was used to dial up on an ADSL line to a new site where we have a EFM circuit which terminates at a Cisco 1841 router managed by our ISP. I therefore need to re-configure our 887 router to work as a conduit from our servers back to the Cisco 1841 as its gateway.
I have asked from our ISP and they told me that i need to configure the 887 to use IP address 176.35.140.65 255.255.255.248 and its gateway should be 176.35.140.70. That's great advice in theory but I don't know how to configure this correctly
Our internal network is using subnet 192.168.42.XX which will need to be retained for local devices.
Cisco Switching/Routing :: 881W - List Connected Wlan Clients?
Mar 4, 2012Cisco 881W WLAN module running in autonomous mode. How do I list connected wireless clients?
View 1 Replies View RelatedCisco Switching/Routing :: Instrument Or Machine Connect To C819G-4G-G-K9 M2M To Have WLAN
Apr 3, 2013I want to buy the CISCO C819G-4G-G-K9 M2M Router. Studying the characteristics as I always do, I discovered (incredible for me!) that so a sophisticated and expensive router has not the WLAN. Nevertheless, to have the Wi-Fi connection is essential for me.
which is the instrument or machine of Cisco that I must use to connect to the CISCO C819G-4G-G-K9 M2M Router and to have the WLAN 2.4/5 GHz? Will this be possible?
Cisco Switching/Routing :: 871 Content Filtering At Specific Time And Multiple Adsl Connections
Jan 23, 2013I have Cisco 871 router with 12.3. OS version.
1. I'm interested if it's possible to block certain contetn only at certain time ? e.g. We would like to block facebook from 7:00 to 10:00 and from 11:00 to 15:00. I was going through cisco manuals but can't find the right answer to this.
2. Cisco 871 has 4 LAN interfaces and one WAN interface. Currently WAN interface is connected to adsl modem in bridge mode and LAN 0 interface is connected to switch.
I'm interested if I could use remaining 3 LAN interfaces for adsl connections same as I'm using WAN interface. Then I would create vlans that would use LAN interface 0. Each of those VLAN's would use different adsl connection.I would assign different IP to each VLAN's so users would be able to change their gateway and use different ADSL connection.
Cisco WAN :: Static Routing Nothing Being Passed Through 887VA-M-k9
Nov 25, 2012I'm having a weird issue with static routing on the Companies Cisco Router. Essentially nothing is being passed through from what I can tell. Im unable to remote in or even email the exchange server its all blocked..
My Current Config
Building configuration...
Current configuration : 5327 bytes!! Last configuration change at 06:05:36 Sydney Tue Nov 27 2012! NVRAM config last updated at 06:05:53 Sydney Tue Nov 27 2012! NVRAM config last updated at 06:05:53 Sydney Tue Nov 27 2012version 15.1no service padservice timestamps debug datetime msecservice timestamps log datetime msecno
[code] ........