Cisco WAN :: 887VA PPPoA BT ADSL Setup?
Feb 29, 2012
Im new to Cisco equipment and weve just upgraded to a all singing 8000 series (887VA) to be precise.
i'm having difficultys in setting the router to connect to our BT ADSL2 business broadband, we have a static IP but on normal cheaper routers you just input a Chap username and password. and the router sorts the rest.
i've followed the tech support from cisco website inputted the configure commands to create the ATM0 and a Dialer0 but still having no joy.when you log into the gui it only shows you a enable PPPoE tick box. no signs of PPPoA?
View 13 Replies
ADVERTISEMENT
Jun 13, 2012
In 12.x I used to go under atm0 and used ' dsl operating-mode' How can I do it under 887VA running 15.2?
View 1 Replies
View Related
Feb 14, 2013
The aDSL circuit is up and connected and I can reach the internet, however not all sites on the internet are reachable. This is occurring on two seperate 887VA’s and the circuit has been tested with a netgear router and no issues occur. The router has been tried on 5 different ADSL connections and the same problem occurs although more websites can be reached on a home broadband connection (ADSL2+ Annex A) as opposed to the problem being more severe on an ADSL2+ Annex M circuit. The problem seems to affect websites that are full of adverts more than sites that have single domain landing pages.
The sites that I cannot reach are pingable. This happens on multiple machines behind the router. The same config is used on an cisco 877-M router with no issues.
! Last configuration change at 14:52:30 UTC Wed Feb 13 2013
version 15.2
no service pad
[Code].....
View 8 Replies
View Related
Jul 7, 2011
I have been trying to connect a new Cisco 887VA Router to the Internet using ADSL via PPPoE and have been unsuccessful. The DSL line is active and functioning correctly since the current "old" router is connected and working without any problems (the "old" DLink router is connected to an Alcatel DSL Modem). AT&T provides the ADSL service to the office. When the Cisco Router is connected it tries to negotiate a connection via PPPoE on the WAN interface but utlimately fails. The IP for the WAN interface is dynamic.
Below is the current configuration of the router.
!
! Last configuration change at 00:43:54 UTC Sun Jun 26 2011
!
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
[code]....
View 9 Replies
View Related
Mar 24, 2013
to configure this router my main objective is ADSL connection, and wireless network setup.
[code]...
View 8 Replies
View Related
Feb 11, 2012
I've got problem trying to connect the CISCO-887VDSL/ADSL OVER POTS ROUTER to internet. Only got the LAN part working.I'm trying to setup PPPoE with dynamic IP Followed CISCO's documentations but the commands used were not recognized by the router.
here's my config.
!
! Last configuration change at 08:31:51 UTC Sat Feb 11 2012
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[code]....
View 1 Replies
View Related
Aug 7, 2012
Have installed an 887VA on the end of a ADSL connection. The provider has specified EF 150 on the link. The router is configured using a Virtual Template.
If the Virtual Template has a service policy applied, we don't have connectivity to their main site - although the CD and PPP lights are lit. As soon as the service policy is removed, we have connectivity.
We've had three sites with the same problem. Two of the sites don't have QoS specified on the link but had the same problem if the service policy was applied.
Hardware - CISCO887VA-SEC-K9
Software - 15.1(4)M4
=== config snippets
class-map match-all Voicematch access-group 10
policy-map Dscpclass Voice priority 150class class-default
interface ATM0
bandwidth 1143
bandwidth receive 12334
[code]....
View 3 Replies
View Related
Dec 6, 2012
We have a remote site connected to ADSL line with a Cisco 887VA router attached. This has been working fine for the last couple of months. However, recently, the site have started to complain of performance issues (network slow, applications disconnecting, etc)Looking on the router, we can see evidence of packet loss/timeouts from a simple ping to the internet e.g. [code]
However, we have logged the fault with our service provider and they return all line tests as clear but what is particularly strange is that they also report “and the SNR Margins are well within threshold levels (Upstream 11.5 and Downstream 15.0)” which, unless I’m misunderstanding something, seems to be completely different from what the router itself is reporting.Is there a reason why the service provider’s stats for Noise Margin would appear to be so different from what the router is reporting?
View 2 Replies
View Related
Aug 30, 2012
difference of CISCO887VA-K9 and CISCO887VA-SEC-K9.I thought it because of the Advanced Security and Advanced IP Licenses, but it isn't, I've got the -SEC- Version now just with the Advanced Security license. So I asking myself why I bought the more expensive CISCO887VA-SEC-K9 if I have to buy the additional Advanced IP Services licenses extra..
View 14 Replies
View Related
May 16, 2013
I have a bit of an issue setting up an Cisco 837/SOHO ADSL Router.
Basically what it is is that my Broadband router isnt doing its job very well, and the last piece of the puzzle in the server area is to upgrade the router, and I have with this. Now. I hve followed the setups as per cisco's guidlines very well and doen alot of research on the CLI commands, I have access to the router and have setup the system.
My broadband in the office is Orange/EE and its PPPoA. I hvae all the settings, and such and have followed a set of commands that apply to BT broadband but, It simply hasnt worked in my case. Any CLI commands to setup this router so i'll replace my business livebox.
View 7 Replies
View Related
Nov 9, 2011
I have reset the router of Cisco 870. I need to connect the router for ADSL connection but don't know how to do it.
[code]...
View 2 Replies
View Related
Feb 21, 2013
I have a RV082 VPN Router. But my internet connection is ADSL brodband. How can i connect and setup a VPN connection to other RV082.
View 1 Replies
View Related
Jul 24, 2011
we are trying to configure PPPOA over Ethernet on Cisco 1812 Router, we have 2 ethernet ports and no ATM ports, hence PPPOA must be applied at a global setting.
View 3 Replies
View Related
Feb 20, 2011
My ISP is *starting* to roll out native-v6, quiet-like, and I'm trying to get it running in the ADSL-connected home-lab. However, for some reason, PPP link setup fails for v6; v4 is fine, as always. The argument which seems to be sent from IPV6CP as the link-ID seems like it might be overlong from some examples I've seen elsewhere. I have seen 48-bit-ish examples, and this one is clearly longer. I've not seen any config extracts that suggest I may have control over this, though. At least not directly.I'd love to know where to look further, or if this is a known bug, but GOOG searches aren't giving me anything seeming relevant. It's *possible* that the ISP needs to tweak something on the LNS side, but says he has another customer with a working setup (not necessarily on the c8xx ISR series hardware, though). I had the same problems on c880data-universalk9-mz.124-22.YB8.bin image as well, and moved to the 15.1(3)T in hopes of better functionality.
Relevant config extracts:
boot system flash c880data-universalk9-mz.151-3.T.bin
! ...
ipv6 unicast-routing ipv6 cef
!...
! interface ATM0 no ip address no atm ilmi-keepalive pvc 0/32 encapsulation aal5mux ppp dialer dialer pool-member 1 ! ! ...
! interface Dialer1 description PPPoA Dialer to ipHouse ip address negotiated ip mtu 1492 ip flow ingress encapsulation ppp dialer pool 1 dialer-group 1 ipv6 address 2001:4980:1000:1E00::2/64 ipv6 address autoconfig ipv6 enable ppp authentication chap pap callin ppp pap sent-username user@isp [snip]! ip forward-protocol nd
[code].....
View 6 Replies
View Related
Dec 13, 2011
with my broadband internet I received a range of 5 IP addresses from BT. I would like to assign one of them to the modem, in order to reach the modem from the outside using that IP.,Is this theoretically possible at all?,Is the WAG320N supporting static IP addresses with PPPoA at all?,When I select PPPoA as the encapsulation on the Setup/Basic setup tab, I cannot enter an IP address on that tab. I tried using the Setup/Ethernet tab, but selecting ""Use as a WAN port", "Static IP", inserting the IP and clicking on "save" result in a cut of the internet connection.
View 3 Replies
View Related
Apr 27, 2011
I plug my modem into the router, and apparently to configure it I need to put my settings into the router, but PPPoA is not in the dropdown, only PPPoE and PPTP. What do I do?
View 1 Replies
View Related
Jan 26, 2007
I lost my CD that I used to do to setup the internet for the router.
View 4 Replies
View Related
Apr 7, 2011
We have a router operating in front of one computer which is separate from the rest of the network. Most of the time it operates fine but we find sometimes it loses connectivity, both internet connectivity from the machine and access to the machine remotely. This is not acceptable as the machine is operating rather critical processes and ideally it should be available 100% of the time.
I cannot determine if the fault lies with Windows, the router or the network.
ADSL Connection Type PPPoE/PPPoA
Firmware v1.06
Port forwarding None
DNS Auto
Firewall None
DMZ 192.168.1.2
View 1 Replies
View Related
Jan 23, 2012
I bought an E2000 router with modem Dlink DSL-320B in PPPoA mode. I have already spent much time for to configure the router with-out any positive feedback . I've selected Automatic configuration with dhcp , static ip 192.168.1.2 and dhcp and modem with 192.168.0.1 and dhcp . If i view the status windows (internet connection) in router i see the right address for gateway and internet Ip , but is not allow to navigate by other PC linked with internal switch of E2000. Do you Know some particluar set-up for PPPoA mode ?
View 5 Replies
View Related
May 21, 2011
Currently, I have 2 Apple Airport Extremes, and 1 Wireless Netgear ADSL Router. The 2 AAEs are connected separately to the router, and this allows us to get coverage in most part of the house (it's a large house with concrete and granite walls). I also have a HP Officejet 8500 'wireless printer' that is wired to the router as you can only print to the printer when it's in standby with a physical connection to the router (that's a different story). So my goal is to replace everything as the router is slowly dying and as a result of this, I want to be able to access the Internet wirelessly throughout the house, and be able to print from any where in the house without anything connected via cables. And as a bonus, I would like the Internet to be accessible 100 yards/metres down the garden (workshop is there). Basically, blanket coverage!
View 3 Replies
View Related
Aug 24, 2012
i have a problem with my adsl line connected on a HWIC-ADSL on router 2901 it was working good until yesterday the atm interface is down but the interface dialer is up .i connected this line into home adsl modem and the line is working good?
View 2 Replies
View Related
Jun 6, 2011
i am trying to setup a hq to 2 remote office vpn connections, all have Cisco 877 ADSL routers.so far to test I tried to setup a site to site vpn between hq and remote 1.
I setup 2 routers with the following settings:
Router 1:
!
!
ip ssh port 3536 rotary 1
ip ssh version 2
!
!
crypto isakmp policy 1
[code]....
View 2 Replies
View Related
Mar 3, 2012
Have they changed the poe requirements for this router? This model seems to be a seconed gen 887 with internal wireless, fanless and instead of there being a second 2 pin power socket for the poe option there is just 1 power input with the text under is saying. 'poe option requires 5a power adapter' I have purchased the 800-IL-PM=2 to delivery poe on the first 2 ports from this document [URL]While the daughter board does fit in the stand off pegs are too short and the power adapter is incompatable.
View 9 Replies
View Related
Mar 25, 2013
Is there a GUI that can be used to setup the 887 router. I need to setup a VPN.
View 1 Replies
View Related
Apr 1, 2011
I'm trying to get an internet connection through my cisco 877va but I can't get access. I cant apply show cotroller vdsl 0 command and I can see DSL up, however, the dialer0 interface can't get access to internet. If I apply "show int dialer0 account" coomand, I get the next message: "No traffic sent or received on this interface". [code]
View 14 Replies
View Related
Feb 13, 2013
Firstly does the 887VA have a WAN port? I know it does VDSLIf this model is doesn't have both these options do you know which model does?
View 1 Replies
View Related
Jan 9, 2013
I need to configure a Cisco 887va router for a customer with a firewall that doesn't support PPPoA. I basically need to ensure all traffic that is recieved from the internet (ADSL connection) is NAT'd to a LAN interface so the firewall can do the specific NATing. I have the following route map and NAT rule in mind, but what I am confused about is that if the atm0 interface needs to be configured as the outside interface and vlan2 as the inside interface. How will the following work?
View 0 Replies
View Related
Nov 25, 2011
I'm trying to get an internet connection through my cisco 877va but I can't get access. I can see DSL up, however, the dialer0 interface can't get access to internet. Here is my configuration:
[code].....
View 2 Replies
View Related
Apr 23, 2013
I have a problem and I dont know much on Cisco Products
The router is Cisco 887 VA
When it starts the Leds Ok AND Fe lan are blinkng then are always on .After 10 seconds lan led is off a and pc shows cable is unplugged
I tried all ports and same thing happened .I tried with different ethernet cord but the problem persists
I installed Cisco Configuration Professional and it hangs on Retrieving Port
View 2 Replies
View Related
Feb 1, 2012
Actually I have to make a VPN between an 5520 ASA and a Cisco 887VA-K9 Router. Connected to ASA I have the outside interface, the inside-DMZ interface, the PCs interface and the VoIP interface. In the other site I will need to have a new subnet and a VoIP phone which I need to connect to the VoIP subnet in the other side in order to work with our CCM servers.I need two VPN established between ASA and 887 Router?
View 15 Replies
View Related
May 9, 2013
I have an 887VA-K9 which boots into ROMMON mode every time. It seems to have 3 tries at booting, then fails.
The entire console output from power-on is (blank lines removed):
System Bootstrap, Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 2009 by cisco Systems, Inc.
[Code].....
View 3 Replies
View Related
Apr 14, 2011
what web-based programs do i need to install a 887VA? I tried Cisco CP express version 2.1, not a supported device.
View 2 Replies
View Related
May 13, 2013
I have set up my network to pass ethernet (layer 2) traffic accross an adsl connection to another 887va router. this link is set up as a L2TP. I have a PC at one end of the tunnel and a web ranger that operates at layer 2 level. I can see the layer 2 traffic entering the router from the PC however it does not seem to go over the L2 tunnel to the other router.
I also need to know what debug codes I can enter to see if the data is being filtered and if so why?the debug L2TP gives the following output:
L2TP Tunnel and Session Information Total tunnels 1 sessions 1
LocTunID RemTunID Remote Name State Remote Address Sessn L2TP Class/
Count VPDN Group
[code]....
View 1 Replies
View Related
