Cisco WAN :: 887va NAT All Traffic To LAN Ports
Jan 9, 2013
I need to configure a Cisco 887va router for a customer with a firewall that doesn't support PPPoA. I basically need to ensure all traffic that is recieved from the internet (ADSL connection) is NAT'd to a LAN interface so the firewall can do the specific NATing. I have the following route map and NAT rule in mind, but what I am confused about is that if the atm0 interface needs to be configured as the outside interface and vlan2 as the inside interface. How will the following work?
View 0 Replies
ADVERTISEMENT
Apr 23, 2013
I have a problem and I dont know much on Cisco Products
The router is Cisco 887 VA
When it starts the Leds Ok AND Fe lan are blinkng then are always on .After 10 seconds lan led is off a and pc shows cable is unplugged
I tried all ports and same thing happened .I tried with different ethernet cord but the problem persists
I installed Cisco Configuration Professional and it hangs on Retrieving Port
View 2 Replies
View Related
May 13, 2013
I have set up my network to pass ethernet (layer 2) traffic accross an adsl connection to another 887va router. this link is set up as a L2TP. I have a PC at one end of the tunnel and a web ranger that operates at layer 2 level. I can see the layer 2 traffic entering the router from the PC however it does not seem to go over the L2 tunnel to the other router.
I also need to know what debug codes I can enter to see if the data is being filtered and if so why?the debug L2TP gives the following output:
L2TP Tunnel and Session Information Total tunnels 1 sessions 1
LocTunID RemTunID Remote Name State Remote Address Sessn L2TP Class/
Count VPDN Group
[code]....
View 1 Replies
View Related
Jun 6, 2013
We are running a Cisco 887VA router for our internet access but of course the port connected to the internal network only supports 100Mbit/s. There are a few 100Mbit/s ports on the router; I was wondering whether it was possible to use more than one port to provide aggregation to get higher speed such as two ports providing 200Mbit/s? We are running Gigabit internal.
View 4 Replies
View Related
May 6, 2013
i have set up a layer 2 tunnel on my 887va router and the traffic transmits accross this to my second 887va. unfortunately, I do not seem able to get the layer 2 traffic from my host PC and down the tunnel.
I believe the problem to be the router settings for the fastethernet aqnd forwarding this data out of the dialer port.
Here is my config:
Building configuration...
Current configuration : 3973 bytes
!
! Last configuration change at 13:03:15 UTC Thu May 2 2013
[Code].....
View 6 Replies
View Related
Aug 30, 2012
difference of CISCO887VA-K9 and CISCO887VA-SEC-K9.I thought it because of the Advanced Security and Advanced IP Licenses, but it isn't, I've got the -SEC- Version now just with the Advanced Security license. So I asking myself why I bought the more expensive CISCO887VA-SEC-K9 if I have to buy the additional Advanced IP Services licenses extra..
View 14 Replies
View Related
Apr 18, 2011
I would like to know how can we allow traffic on ports 3389 (rdp) and 8007 which comes from any to 192.168.2.10 but pretend to be a Phones interface 192.168.2.1? [code]
View 9 Replies
View Related
Oct 21, 2011
I am in search of a new routers. I don't have any special task to do. Just the flow of maximum 2mb/sec data and some times video conference. However I need the Voip solution as well. I just got excited on the cisco ASA 5505 product. Can this fulfill my requirements. Can this work as the router 1841. Does this support DMVPN, SSL VPN and dynamic routing. Can I upgrade the IOS for dynamic routing purpose. Do you recommend to purchase this produe act or not instead of router ? What are the limitations of this product. If I purchase this I can use this as an router as well as strong security solution. How many ports are available for traffic flow in ASA 5505. Are all routed mode or some of them switch port.
View 1 Replies
View Related
Aug 10, 2011
enabling traffic between interfaces on the ASA 5510. Of course I have an outside interface E0/0 and an inside interface (E0/1) for normal operation. The idea was to enable one of the remaining interfaces on the 5510 to attach an internal network resource to for management in case we lost our switch. I am using E0/0 as the outside interface and the inside interface is E0/1. I am wanting to attached a management device on the same inside network IP address range for simplicity. I have E0/2 configured for the same security level (100) as the other inside interface and I also have enabled same-security-traffic permit inter-interface as well but I still cannot access the device on that port. Is there something else I am missing? I guess the best way to explain this is that I want ports E0/2 and E0/3 to act like a "switch" so to say...... The ASA 5505 lets you do this pretty easy but having trouble on the 5510.
View 4 Replies
View Related
Dec 12, 2011
I have a question around pix 501 (6.3) configuration. I am trying to allow traffic from a single Citrix CAG across a variety of ports (80,443,9001-9005,27000,7279,1494,2598) from external (dmz) interface through to multiple addresses (on the same ports) on the internal (secure) network and dont know how to best approach it or if its possible. The only way I have found to allow traffic through is via Static Nat entries which I cant see will work for this requirement as we need some ports to be allowed into multiple addresses.
View 6 Replies
View Related
Jul 29, 2012
So I am trying to get traffic from 192.168.1.33 on UDP ports 10000-20000 and port 5222 (udp) to have DSCP set to EF and Forwarded accordingly.
Building configuration...
Current configuration : 32481 bytes!! Last configuration change at 22:52:11 UTC Mon Jul 30 2012!version 12.2no mls acl tcam share-globalmls netflow interfacemls qosmls cef error action freezevty-async!!spanning-tree mode pvstdiagnostic bootup level completeaccess-list 99 permit 192.168.1.51access-list 99 permit 192.168.1.9access-list 99 permit 192.168.1.8access-list 99 permit 192.168.1.12access-list 111 permit udp any any range 10000 20000access-list 111 permit udp any any range 1 9999access-list 111 permit tcp any anyaccess-list 111 permit udp any any range 20001 49151access-list 111 permit udp any any range 50000 65535access-list 150 permit udp any any eq 5060!redundancymain-cpu auto-sync running-configmode sso!ip access-list extended Modesto_Officeremark Wireless Linkpermit tcp any any establishedpermit icmp any anypermit udp host 65.214.162.12 host 99.24.26.84 eq tftppermit ip host 65.214.162.24 host
[code]....
View 1 Replies
View Related
Sep 5, 2011
Does the ESW 520 24P Support Mirroring 20 Ports Traffic to 1 Destination Port?
View 3 Replies
View Related
Jan 24, 2012
At present we are having a 4900 series switch where we are running one monitor session.Additionaly we are in need of capturing VLAN traffic and set the destination to 2 * GE ports , both are in the same switch.Due to the limitation of two monitor sessions per switch , we thought of putting the destination ports as port channel but it looks like it is not supported.
View 1 Replies
View Related
Jan 20, 2013
I've been digging into some performance issues on a LAN that has a couple of 2960s. The monitoring software I'm using has indicated a high amount of discarded outbound packets (up to 5%). The suggested resolutions were to enable flow control.
My question is does enabling flow control on all ports interrupt network traffic at all? this is a production network so I had already planned on doing it during off hours but also wanted to know if I should be prepared for any significant drop in traffic.
View 14 Replies
View Related
Nov 5, 2012
i would like to monitor traffic between multiple source ports to multiple destination ports on a nexus 7k. i lknow when you set up monitor session is between source and destination (laptop or traffic analyser) but is there a way i can set up between source and multiple destination ports and capture that traffic ?
View 3 Replies
View Related
Apr 24, 2013
I posted my complaint on Amazon.com recently. My E4200 router stopped allowing traffic through ports completely. I was able to unplug the power and allow the router to cool, and the router would work for a while then stop after about 10 minutes. I assume that the unit was overheating, but I do not have the equipment of a test facility.I bought a Belkin AC 1200 router which is a bit of an upgrade from Amazon.com. I do not think that there is anything that Linksys can do for me as my warranty expired. I just thought that when I spent what was to me a lot of money the router should have lasted longer.
View 5 Replies
View Related
Mar 22, 2012
I've been looking into IGMP snooping and have read that a L2 switch will forward multicast traffic to all ports connected to an interested receiver AND all mrouter ports. In a L2 'V' topology this results in all multicast traffic routed onto a VLAN being forwarded to the 2nd distribution switch. My question is how should a 6500 Sup720 deal with this unwanted multicast traffic? Both a Local SPAN of the RP and a Netdr capture suggest that this traffic is punted to the RP and ultimately dropped. Is this expected behavior or should the traffic be dropped in H/W?
View 2 Replies
View Related
Mar 3, 2012
Have they changed the poe requirements for this router? This model seems to be a seconed gen 887 with internal wireless, fanless and instead of there being a second 2 pin power socket for the poe option there is just 1 power input with the text under is saying. 'poe option requires 5a power adapter' I have purchased the 800-IL-PM=2 to delivery poe on the first 2 ports from this document [URL]While the daughter board does fit in the stand off pegs are too short and the power adapter is incompatable.
View 9 Replies
View Related
Mar 25, 2013
Is there a GUI that can be used to setup the 887 router. I need to setup a VPN.
View 1 Replies
View Related
Apr 1, 2011
I'm trying to get an internet connection through my cisco 877va but I can't get access. I cant apply show cotroller vdsl 0 command and I can see DSL up, however, the dialer0 interface can't get access to internet. If I apply "show int dialer0 account" coomand, I get the next message: "No traffic sent or received on this interface". [code]
View 14 Replies
View Related
Feb 13, 2013
Firstly does the 887VA have a WAN port? I know it does VDSLIf this model is doesn't have both these options do you know which model does?
View 1 Replies
View Related
Nov 25, 2011
I'm trying to get an internet connection through my cisco 877va but I can't get access. I can see DSL up, however, the dialer0 interface can't get access to internet. Here is my configuration:
[code].....
View 2 Replies
View Related
Feb 1, 2012
Actually I have to make a VPN between an 5520 ASA and a Cisco 887VA-K9 Router. Connected to ASA I have the outside interface, the inside-DMZ interface, the PCs interface and the VoIP interface. In the other site I will need to have a new subnet and a VoIP phone which I need to connect to the VoIP subnet in the other side in order to work with our CCM servers.I need two VPN established between ASA and 887 Router?
View 15 Replies
View Related
May 9, 2013
I have an 887VA-K9 which boots into ROMMON mode every time. It seems to have 3 tries at booting, then fails.
The entire console output from power-on is (blank lines removed):
System Bootstrap, Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 2009 by cisco Systems, Inc.
[Code].....
View 3 Replies
View Related
Apr 14, 2011
what web-based programs do i need to install a 887VA? I tried Cisco CP express version 2.1, not a supported device.
View 2 Replies
View Related
Jan 26, 2012
I've got a brand new C887VA-W-E-K9 that is up and running on a BT VDSL connection. That side of it is fine... But the integrated AP module on it keeps reloading.. I can be on the AP console reading the config via 'sh run' and suddenly it'll be loading the OS again... There's no errors logged, no errors on the console or anything... (I also have yet to get the radio working, it starte dbefore I'd finished the config).
It doesn't seem to be anything I'm doing as if I just leave the console, it'll just sit there... reloading every few minutes... (Although sometimes it seems to stay up for longer).
The console just looks like this. WHich is taken from listing the running config and while sitting at the --more-- prompt... Bang...
interface GigabitEthernet0
description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router
no ip address
[Code].....
View 6 Replies
View Related
Jan 3, 2013
I am struggling to get this working after spending many hours looking at it I am now completely stuck. We are upgrading from a 857W to this 887 VA-M I have some experience of IOS and the 800 series. Our 857W works perfectly using almost the same config. Our situation is that the router will sit in front of our firewall and act essentially as a simple router passing everything through to our Firewall. Nat is done at the Firewall.
We currently have the following configuration that seems to connect the the ISP fine but I cannot connect to the vlan2 port on the switch the firewall cannot connect to he internet or route anything via the Vlan2 port no pings etc.. I am using Fast Ethernet 0 as the Vlan2 port and the rest are V LAN 1 with a local network address to allow me to connect a laptop.
We have a block of static IP addresses, the base of which is assigned to the V LAN 2 interface and used by Dialer 0 as IP Unnumbered. Config below.
4590 out of 262136 bytes
! Last configuration change at 17:42:06 UTC Thu Jan 3 2013
! NVRAM config last updated at 17:43:00 UTC Thu Jan 3 2013
! NVRAM config last updated at 17:43:00 UTC Thu Jan 3 2013
[ code].....
View 2 Replies
View Related
Jun 17, 2012
I'm facing an issue since 2 month now , no one is able to tell me what's going on. The line goes down suddently for 2 or 3 minutes and this happens everyday at the same range (~2 or 3 hours) of time . I don't have any scheduled task to cause this. ISP in his side has also made some tshoot but found nothing and is convinced that the problem is coming from our side :
Here is some log :
Cisco IOS Software, C880 Software (C880DATA-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
rtr-Id#show debugging
Generic IP:
IP packet errors debugging is on
IP NAT ERROR debugging is on
PPP:
[Code]...
View 3 Replies
View Related
Nov 2, 2012
We have a 887VA and a dns/web/mail/ftp server behind (below address 192.168.99.100).
first problem I forwarded the necessary ports to the server address, but now the domain became invisible and all the above servers stops to respond.
second problem whenconfiguring a fixed ip addres on a PC with GW and DNS server the 887VA address no internet connection possible, but when put instead the route address in the dns the ISP dns address internet comes back.
Put this server on DMZ, so all services will be available from the outside? forth how to connect the route remotely (with putty)
This site is my only hope to succeed one day to manage this "black" box successfully. Below the running conf
! No configuration change since last restart
version 15.1
no service pad
[Code].....
View 9 Replies
View Related
Mar 23, 2011
I have a adsl setup from my ISP (TDC) and I would like to use my 887va as modem instead of the supplied Motorola Modem.I have the technical info on the connection: VPI = 0, VCI = 101 and RFC1483 AAL5snap. I have supplied the 887VA with an IP address on VLAN1. What is the right direction in terms of access-lists, dialer interfaces, routing etc.I have tried serveral guides on Cisco pages but have not managed to even ping google from my 887va.
View 1 Replies
View Related
Nov 25, 2012
I'm having a weird issue with static routing on the Companies Cisco Router. Essentially nothing is being passed through from what I can tell. Im unable to remote in or even email the exchange server its all blocked..
My Current Config
Building configuration...
Current configuration : 5327 bytes!! Last configuration change at 06:05:36 Sydney Tue Nov 27 2012! NVRAM config last updated at 06:05:53 Sydney Tue Nov 27 2012! NVRAM config last updated at 06:05:53 Sydney Tue Nov 27 2012version 15.1no service padservice timestamps debug datetime msecservice timestamps log datetime msecno
[code] ........
View 1 Replies
View Related
Apr 29, 2013
I have cisco router 887VA.Question is when i connect that WAN port ( eth0) with any switch or laptop/pc i do not see the port in up state. What can be the reason.I have done "no shutdown " on interface level and there is no configuration on interface except the IP address , but it show " up down "state even the port is connected to some device. ( Is the port is faulty or some other reason).As per my concept it should show up state when we connect to some device ( Like router / switch / laptop).
View 6 Replies
View Related
Jun 13, 2012
In 12.x I used to go under atm0 and used ' dsl operating-mode' How can I do it under 887VA running 15.2?
View 1 Replies
View Related
