Cisco Firewall :: Enabling Traffic On E0/2 And E0/3 Ethernet Ports - ASA 5510
Aug 10, 2011
enabling traffic between interfaces on the ASA 5510. Of course I have an outside interface E0/0 and an inside interface (E0/1) for normal operation. The idea was to enable one of the remaining interfaces on the 5510 to attach an internal network resource to for management in case we lost our switch. I am using E0/0 as the outside interface and the inside interface is E0/1. I am wanting to attached a management device on the same inside network IP address range for simplicity. I have E0/2 configured for the same security level (100) as the other inside interface and I also have enabled same-security-traffic permit inter-interface as well but I still cannot access the device on that port. Is there something else I am missing? I guess the best way to explain this is that I want ports E0/2 and E0/3 to act like a "switch" so to say...... The ASA 5505 lets you do this pretty easy but having trouble on the 5510.
I've been digging into some performance issues on a LAN that has a couple of 2960s. The monitoring software I'm using has indicated a high amount of discarded outbound packets (up to 5%). The suggested resolutions were to enable flow control.
My question is does enabling flow control on all ports interrupt network traffic at all? this is a production network so I had already planned on doing it during off hours but also wanted to know if I should be prepared for any significant drop in traffic.
We've got a proyect that requires a few thin clients to connect to a remote PCoIP server.
Looking to the documentation, the only port required to be open through Firewalls is TCP/UDP 4172, however, we've seen (making interface captures) that it somehow also uses ESP (IP protocol 50).
We've got a static NAT translation translating those thin clients to a public IP address, we've created ACLs to allow inbound (shouldn't be necessary as our user is connecting to a remote server) and outbound traffic for TCP/UDP 4172 and ESP and I cannot make it work.
I've also enabled IPSec pass-through Inspection to no avail.
how should we configure our ASA to enable this kind of traffic?
I have a ASA 5510 firewall with CSC module and Security Plus license for CSC module.Will you tell me how to configure my firewall to send emails to particular mail ID when someone login into the firewall or any virus attacks from outside.
I'm having a problem with an ASA 5510 and software from Manage Engine (Firewall Analyzer). They are saying that sys log 113019 is not getting data over to the server where the firewall analyzer is installed. I'm checking the config and I see it enabled. Why this particular sys log info isn't making it to the reporting software when other data is.
We have an ASA 5505. 5505 comes with two default vlans 1&2 with each of them marked as inside & outside respectively.My query is , if i do not want to use vlans on 5505 and only want to use the Ethernet ports as pure physical layer 3 ports, is it possible?i.e. i want to assign a layer 3 ip address on eth0/0 and eth0/1 and make them as the inside & outside interfaces rather than vlans. is it possible to do away with vlans in 5505 & will it work otherwise?
I currently have an ASA 5510 unit. I have a dmz setup which house some web servers and an inside interface. The web servers contain multiple public ip addresses which I have natted and access is fine.What is the most simple way to enable ping for my dmz from the outside. Meaning if someone outside the network pings one of the servers by its public ip address I would like it to respond to ping.
We have setup new ip camera system and as per our vendor to access the camera from outside we need to open,TCP ports and in firewall and forward to our camera server.
Let say our public ip address is 207.114.111.22 and our local ip address for the camera is 11.11.1.30. We have cisco asa 5510.
I would like to know how can we allow traffic on ports 3389 (rdp) and 8007 which comes from any to 192.168.2.10 but pretend to be a Phones interface 192.168.2.1? [code]
I am in search of a new routers. I don't have any special task to do. Just the flow of maximum 2mb/sec data and some times video conference. However I need the Voip solution as well. I just got excited on the cisco ASA 5505 product. Can this fulfill my requirements. Can this work as the router 1841. Does this support DMVPN, SSL VPN and dynamic routing. Can I upgrade the IOS for dynamic routing purpose. Do you recommend to purchase this produe act or not instead of router ? What are the limitations of this product. If I purchase this I can use this as an router as well as strong security solution. How many ports are available for traffic flow in ASA 5505. Are all routed mode or some of them switch port.
I have a question around pix 501 (6.3) configuration. I am trying to allow traffic from a single Citrix CAG across a variety of ports (80,443,9001-9005,27000,7279,1494,2598) from external (dmz) interface through to multiple addresses (on the same ports) on the internal (secure) network and dont know how to best approach it or if its possible. The only way I have found to allow traffic through is via Static Nat entries which I cant see will work for this requirement as we need some ports to be allowed into multiple addresses.
Our cisco asa 5510 getting sometimes boot and sometimes not. sometimes LED on port comes back if boot and sometimes not. what are the parameter should be check to rectify problem.
I just finished implementing a VOIP install and I am trying to setup some softphones and in order to allow the softphones to work I need to open some specific ports for outbound. I am not a Cisco guy, I am a Windows Administrator that also has to maintain my Cisco infrastructure.
I got a situation here for Nat-ed IPs i configured. I expected to open some ports on the interface to allow certain traffics to pass through, yet there are some of them are failed. Down is my current config.
object-group service DM_INLINE_SERVICE_1 service-object icmp service-object tcp destination eq https
[Code]....
The only ports opened are 443, www, 3389 while ports domain, 5061,3478,3389. how to open domain, 5061, 3478, and 3389 ports on my ASA .
I have inherited an asa 5510 whit 4GE SSM module installed. The asa runs fine, but i can not use the 4GE SSM ports. Using ASDM or console i can get and configure the gigabitethernet1/x ports but i can not get traffic on it. The ping from the console to the ip address of the Gigabitethernet1/0 is successful. On switches or hubs connected to those ports i can not see the port's mac address. The two Internal-data0/0 and Internal-data1/0 are down and i can get they up. How to configure 4GE SSM or ASA internal-data ports.
We have just acquired a cisco profile 42 video conferencing equipment and am required to open ports for SIP and H232, any pointers on hw that can be acquired i have a cisco ASA 5510, Some one told me to open port 16384 but i need pointers on how to do it becuase I already set an access list to any.
the config
Internet -> ASA 5510 -> Switch -> Profile 42 and other devices
I have a classical "inside + DMZ + outside" configuration.I also have a mail server in DMZ which have to be allowed to reach any destination on the outside (internet) at least on the SMTP port, of course.If I make an access rule that allows traffic from that server to "any", everything works fine, but doing so the server is allowed to reach any destination, including what is behind the inside interface (internal network).I didn't find any other option to tell the ASA machine to allow any destination, but on the outside interface only.I do believe is possibile to have the ASA to allow any kind of traffic from a host on the DMZ to the outside interface only, but I didn't figure out how.
P.S.: I'm using a 5510 machine running version 8.2
Just wondering if there are any methods or commands, natively, in the asa5510 for determining all traffic in to and from a certain server passing through the asa. This would be without a syslog server or something similar.
Core Internal Network -> Cisco ASA 5510 -> DMZ Switch.If i send a ping reguest from internal network to servers in DMZ Switch over the ASA 5510, i can see a delay in response, some times this delay can be more than 80ms, this is a problem for the web applications in http traffic.How i can find what's happening on my ASA? I disable the inspect traffic over the IPS, disable the policy maps below, reload the two boxes, but doesn't works, the problem still persists. [code]
I'm currently using ASA 5510 with software 8.4.1 and I have an issue with nat configuration. I used the following config line:nat (inside, dmz) source dynamic LAN Pat1 destination Server1 Server1
The traffic is not flowing and when I use Packet Tracer, packets are dropped at the NAT rule with the following error: Drop-reason: (acl-drop) Flow is denied by configured rule.The only ACE I have is permit ip any any.
I have an ASA with an outside ACL that is configured to allow 208.84.248.95 SIP/5060 to 1x.x.x.46. I show no hits. I added an ACL to do a packet capture, it sees the packet coming into the ASA but not going to the Serv Prov interface. I see hits on the vuong ACL but not the production acl_out ACL.. What is up?
NOTE:ACL_out is the ACL we use to allow outside traffic to enter our network. FW1(config)# sh access-list | i 1.x.x.46 access-list acl_out line 1 extended permit ip host 63.x.x.140 host 1x.x.x.46 (hitcnt=0) 0xc09a9387 (*NO HITS) access-list acl_out line 658 extended permit udp host 208.84.248.95 host 1x.x.x.46 eq sip (hitcnt=0) 0x0f327179 (NO HITS) [code]...
It was tested and verified from the inside network to make sure the server is listening on that port. Below we created an ACL to allow all IP from another test PC to the Server IP 1x.x.x.46. We did a telnet to port 5060 and it showed hits but not on the acl_out ACL.
Below we applied the same ACL to the ServProv interface to see if traffic was going where it was supposed to . By trying to telnet to the 1x.x.x46 IP from 63.x.x.140 IP. Looking below, no traffic appeared on the capture2.
Capture 1 above shows the last 3 incoming messages initiated from 63.x.x.140 to the 1x.x.x.46! Vuong ACL belows shows 3 more hits.....nothing on the acl_out ACL???
FW1# sh access-list vuong access-list vuong; 1 elements; name hash: 0x29df3e90 access-list vuong line 1 extended permit ip host 63.x.x.140 host 1x.x.x.46 (hitcnt=6) 0x2759fa92 [code]...
I have manually configured the Firewall ASA 5510 from existing PIX to match the configuration, however when I connect the firewall to the Network, no traffic is flowing in either direction. I have the Inside network on the 172.29.0.0 subnet and the outside network on 20.2.0.0 subnet. I am attaching the cofiguration file.
One Host on inside network needs to access customized application hosted on Internet. Its a customized application run on port 80, 443, 5000-to-50020
How do I allow this host access for this specific application. I got ASA 5510 and host is in the inside network, we also got an ACL on inside interface to have control.
-Host IP on inside network - 172.16.30.15 -Application to access - 74.219.x.x -Inside ACL name - inside-acl
I have an issue on an ASA 5510 that I have noticed today, when I am using the log viewer all of the information recorded only shows the high end source and destination ports. For example
Source IP 10.10.4.69 Source Port 59886
Destination IP 8.8.8.8 Destination Port 59866
So what seems to be happening is that I am seeing only half of the connection in the log viewer, I see the side with the high end ports and not the side with the ports the application uses, this example was done with a ping. All my services are working correctly and the client sending the ping gets the response expected, it just seems I have lost the logging display?
I use ASA 5510 and I would like to log VPN traffic ( for example, as soon as a remote user try to connect to the asa). I would like this log be send to a specific mail address. I already configure Email Logging for severity ( level 3) and it works well.
Is there any difference with traffic shaping capability on the 5510 as opposed to the 5505? is there anything the 5510 can do that the 5505 cant? with regards to TShaping?
i would like to use ISP2 for all http/https/ftp traffic.how could I force my ASA to set a different gateway for http/https/ftp traffic ?i have tried several solutions such as nat/pat rules, nothing seems to work.
FTP traffic routed from outside to the inside interface works fine. I have another interface with multiple sub-interfaces and vlans configured. FTP traffic routed from the outside to vlan2_servers is not making it through the firewall. I must be missing something. I have attached my config.
I have ASA 5510 8.4 Firewall where more than 20 Site to Site VPN Clients are configured on it. how to see the traffic for one Specific Site to Site VPN.Actually this site to site vpn is always keep dropping for every minute. I'm sure its a problem at the other end.The remaining 19 VPNS are UP and working without any problem. How to see the traffic for specific vlan.More over we dont have any syslog server in our network. Is their any chance we can check the traffic on the firewall?
I have a private network behind a configured Cisco ASA 5510. I need to send data back and forth between a server on the inside network and a device on the outside network on port 44818. No amount of configuration is allowing this to happen. The packet tracer always fails on of the implicity "deny" rules, even though my other rule should explicitly permit it. I also realize I need to set up routing from my outside network to the inside network, but I cannot see from the documentation how to do that on this particular port without simultaneously breaking my outside connection.
The inside IP for the ASA is 192.168.25.1 The outside IP for the ASA 192.168.11.54
Here is my current configuration:
: Saved : Written by enable_15 at 08:49:25.956 UTC Thu Feb 2 2012 ! ASA Version 8.2(5)
