I just finished implementing a VOIP install and I am trying to setup some softphones and in order to allow the softphones to work I need to open some specific ports for outbound. I am not a Cisco guy, I am a Windows Administrator that also has to maintain my Cisco infrastructure.
View 3 RepliesI got a situation here for Nat-ed IPs i configured. I expected to open some ports on the interface to allow certain traffics to pass through, yet there are some of them are failed. Down is my current config.
object-group service DM_INLINE_SERVICE_1
service-object icmp
service-object tcp destination eq https
[Code]....
The only ports opened are 443, www, 3389 while ports domain, 5061,3478,3389. how to open domain, 5061, 3478, and 3389 ports on my ASA .
We have setup new ip camera system and as per our vendor to access the camera from outside we need to open,TCP ports and in firewall and forward to our camera server.
Let say our public ip address is 207.114.111.22 and our local ip address for the camera is 11.11.1.30. We have cisco asa 5510.
I'm setting up a second exchange 2010 server at a DR location and have been experiencing some problems. The two sites are connected via a pair of ASA5510's using the point to point VPN. I want to rules out any possible VPN issues that may be blocking ports and wanted to see if there is an easy way to do this and simply allow all traffic without any restrictions between the two ASAs. I've attached the scrubbed configs here...Ewing is the primary site and DBSi is the DR site.
View 2 Replies View RelatedI have an ASA 5505 with ASA version 7.2(2) and ASDM version 5.2(2) and I am attempting to open ports 88 and 5445 and forward them to the IP address of my DVR. This is all new for me. I see several posts for other software version to do this same thing but my version appears to be older?
View 1 Replies View Relatedwhat are default ports are open on asa 5520 from outside interface (Zero level Security ) to inside interface (Security level 100)
View 3 Replies View RelatedI have an ASA 5501 running latest code. Per the article at [URL], I need to open the below ports. I have 5 Xboxes (when people come over) and they all have a static IP. My network is 192.168.0.x and is a /24 network.Xbox LIVE requires the following ports to be open: Port 88 (UDP)Port 3074 (UDP and TCP)Port 53 (UDP and TCP)Port 80 (TCP)port 1863 (UDP and TCP) (Kinnect) I defined the various network ports as a service and then created 5 hosts called xbox1, 2, etc with a static IP. I dont have access from the command line (forgot telnet and ssh passwords) , so from the gui, what do I do next?
View 7 Replies View RelatedI'm working on setting up a PBX server in our office, and I'm having trouble getting a port opened for SIP on my ASA 5505.I created static NAT rule for SIP traffic from internal server to the outside IP address.I created access rules on outside interface to forward port 5060 to internal PBX server (192.168.1.8)I also disabled sip packet inspection on the ASA.I'm still receiving a message from the PBX that the firewall is configured incorrectly.
[code]....
I need to open the following ports on a pix:
-tcp 3230 to 3235
-udp 3230 to 3253
How do I open the ports?
I need top open ports 80, 443 and 1882 to a specific external client (IP address).
View 8 Replies View RelatedHow to list ports open on Cisco ASA 5505 appliance? I have tried to see using Cisco ASDM launcher, but no luck.
View 1 Replies View Related-I need to configure the following on my PIX:
TCP port 2195 - outbound
-TCP port 2196 - inbound
How would I configure this via ASDM?
I would just like to to open UDP port 123 in the ASA 5510 Firewall so that our Primary Domain Controller could use this port to sync time with an external time source. We have already added an access rule for this port under the firewall configuration in ASDM 6.4 and this port was also allowed in the inbound and outbound rule of the PDC's Firewall but it seems that it was still blocked.
View 23 Replies View RelatedI have the port numbers but do not know how to proceed from there. Router is a WRT160N V2.
View 9 Replies View RelatedWe have an ASA5510 that we need to open port 25 to allow mail traffic to our internal Exchange server.We have 2 interfaces defined... one named Internal on eth0/3 ip 10.1.x.x and one named Internet on eth 0/0 ip 96.56.x.x.We followed the instructions in ASDM for allowing access to a public server but confusion over definitions have stopped us.ASDM asks for the internal interface and the internal server IP... no problem there because the internal interface and server have two different IP addresses. The Internal interface is eth 0/3 (10.1.1.1) and the server is 10.1.1.2.
However, when we get to the External interface (eth 0/1) there is only a single IP address 96.56.x.x but the ASDM asks for an Interface IP and the IP people would use to get to the mail server from the outside. Inasmuch as we have only 1 external IP address (which connects to our upstream Cisco router which in turn connects to the ISP modem) we used the same IP for both but the ASDM returns an error indicating they must be different.
Apparently we do not have a clear understanding of what the ASDM is actually asking for. When the ASDM asks for the external interface we assumed it was asking for the named value we gave the interface (which is Internet). The named value "Internet" has an ip associated with it 96.56.x.x. But when the ASDM asks for the ip people on the outside would use to get to the mail server (we created a named value called "mail server" and gave it the same ip address as the external named value. This duplication of ip address causes the ASDM to return the error stating that external Interface to be used and the external ip to be used cannot be the same.Have we made an error when we assumed that when the ASDM asked for the external interface it meant the ip of the external interface or was it asking for the eth number (as in eth 0/0) for the interface?
We are running a Cisco ASA 5510 in our district. We have been using it for about a year and a half after an upgrade from our PIX. I have been using the CLI to manage it but I wanted to start using the ASDM. I installed the ASDM Launcher last Friday but could not access it. I have enable the http server on the ASA, assigned an IP to the interface, and granted my machine's IP inside access. On Friday I was unable to launch the ASDM. I then downgraded Java. I came in this morning and was able to connect through the launcher. However I could not make any changes as it would give me an error message and often popped up with "lost connection" type messages. I then closed the ASDM but could not reconnect after that. When I try to connect through the launcher I receive the message "Unable to launch ASDM from 172.16.5.1: Connection reset". When I try https://172.16.5.1/admin/ from a browser I simply receive "page cannot be displayed". I'm not sure why I can't connect.
[Code] ........
We have a ASA5510 and I need to open port 22 for a speacific IP in our LAN outbound only.
View 15 Replies View RelatedIs there a way of ascertaining whether my 5510's have 1 memory slot or 4 memory slots without having to open the chassis?
View 6 Replies View RelatedOur cisco asa 5510 getting sometimes boot and sometimes not. sometimes LED on port comes back if boot and sometimes not. what are the parameter should be check to rectify problem.
View 3 Replies View RelatedTrying to get port forwarding going using ASDM 6.4 on a Cisco 5510
I want to forward port 25/Smtp to 192.168.1.10
I have added all the rules as outlined in the link below. [URL]
But when running an open port checker on [URL]
It says the port is closed, I have noticed that under Access Rules under the Hits columns it says 52 ?
i have a cisco asa 5510 and would like to add a NAT rule for a range of ports like 50000-59999
View 1 Replies View RelatedI have inherited an asa 5510 whit 4GE SSM module installed. The asa runs fine, but i can not use the 4GE SSM ports. Using ASDM or console i can get and configure the gigabitethernet1/x ports but i can not get traffic on it. The ping from the console to the ip address of the Gigabitethernet1/0 is successful. On switches or hubs connected to those ports i can not see the port's mac address. The two Internal-data0/0 and Internal-data1/0 are down and i can get they up. How to configure 4GE SSM or ASA internal-data ports.
View 8 Replies View Relatedenabling traffic between interfaces on the ASA 5510. Of course I have an outside interface E0/0 and an inside interface (E0/1) for normal operation. The idea was to enable one of the remaining interfaces on the 5510 to attach an internal network resource to for management in case we lost our switch. I am using E0/0 as the outside interface and the inside interface is E0/1. I am wanting to attached a management device on the same inside network IP address range for simplicity. I have E0/2 configured for the same security level (100) as the other inside interface and I also have enabled same-security-traffic permit inter-interface as well but I still cannot access the device on that port. Is there something else I am missing? I guess the best way to explain this is that I want ports E0/2 and E0/3 to act like a "switch" so to say...... The ASA 5505 lets you do this pretty easy but having trouble on the 5510.
View 4 Replies View RelatedWe have just acquired a cisco profile 42 video conferencing equipment and am required to open ports for SIP and H232, any pointers on hw that can be acquired i have a cisco ASA 5510, Some one told me to open port 16384 but i need pointers on how to do it becuase I already set an access list to any.
the config
Internet -> ASA 5510 -> Switch -> Profile 42 and other devices
I have an issue on an ASA 5510 that I have noticed today, when I am using the log viewer all of the information recorded only shows the high end source and destination ports. For example
Source IP 10.10.4.69
Source Port 59886
Destination IP 8.8.8.8
Destination Port 59866
So what seems to be happening is that I am seeing only half of the connection in the log viewer, I see the side with the high end ports and not the side with the ports the application uses, this example was done with a ping. All my services are working correctly and the client sending the ping gets the response expected, it just seems I have lost the logging display?
I have a Cisco 877 connected to a VSAT modem, and I can't open ports outside, I dont know why?The Cisco 877 Fa0 port is connected to the VSAT modem at VLAN9, and the rerst of ports are connected to the local lan network at Vlan2. I can enter to Internet, but I can't open port outside. ADSL over pots is not used here.I need to open port 81 for ip address 192.168.1.130 and I dont know why this isn't working. Also if I do: sh ip nat translations I see this:
sh ip nat translations
cisco877#sh ip nat translations
Pro Inside global Inside local Outside local Outside global
tcp 172.30.xx.122:81 192.168.1.130:81 --- ---
udp 172.30.xx.122:81 192.168.1.130:81 --- ---
[code].....
How can I allow all ports to be open? I don't really want my 1811 to block any traffic. I tried the command access-list 1 permit any which allows me to surf the internet, but when I check my web server, and port 3389 (Remote desktop) on yougetsignal.com it says those ports are blocked.
View 6 Replies View RelatedI need to open ports 25, 993, 995, 443 and 465 to setup MS-Exchange. I don't have an inhouse IT guy and this seems pretty straight-forward in theory but I can't figure it out I need to open ports 25, 993, 995, 443 and 465 to setup MS-Exchange.
View 5 Replies View Relatedwhat command should I use to see all open TCP and UDP ports on my router?
View 2 Replies View RelatedI was told i need to open certain ports to certain IP's,what ports need to be opened to what IP's for the folowing game as im close to giving up.The games are as follows - Call of Duty 4, Counter Strike 1.6 and Source, Warcraft III, and StarCraft 2
View 2 Replies View RelatedThe problem is I don't know what to do to open my modem's ports because every single of them except of 80 is blocked,im having some latency problems on online games etc, I asked my ISP and they didnt probably understand what the port is they offered me changing my IP to PUBLIC IP for onetime payment, seeing as they probably dont know what the port is im confused now, will the public ip unblock the other ports?
View 19 Replies View RelatedNo ports seem to open up when they are supposed to be open according to the routers GUI.When i use "port checker"-websites, they even say that port 80 is closed until i actively open it in the router, then it shows up as open. This however only applies to port 80, no other ports shows as open OR allow any traffic through.The same thing happens when the router is in DMZ.What I have done so far is google my butt off without any results, I have tried a new router, a new network card, formated, re-installed windows and made sure that my ISP is not blocking the ports that i have tried to open.My purpose of opening a port is to run a mumble server, which I have run on a Hamachi VPN so far, and that has worked fine.
View 10 Replies View RelatedI can't open up any ports.I've tried using applications such as Simple Port Forwarding, PFPortChecker and manually by opening my router gateway (192.168.1.1).I can open a port, but if I check whether the port is open, it says that the port is closed. I tried opening ports through Windows Firewall and even disabling firewall, still won't work.
View 14 Replies View Related