I have an ASA 5505 with ASA version 7.2(2) and ASDM version 5.2(2) and I am attempting to open ports 88 and 5445 and forward them to the IP address of my DVR. This is all new for me. I see several posts for other software version to do this same thing but my version appears to be older?
View 1 RepliesI'm working on setting up a PBX server in our office, and I'm having trouble getting a port opened for SIP on my ASA 5505.I created static NAT rule for SIP traffic from internal server to the outside IP address.I created access rules on outside interface to forward port 5060 to internal PBX server (192.168.1.8)I also disabled sip packet inspection on the ASA.I'm still receiving a message from the PBX that the firewall is configured incorrectly.
[code]....
How to list ports open on Cisco ASA 5505 appliance? I have tried to see using Cisco ASDM launcher, but no luck.
View 1 Replies View RelatedI need to open ports 25, 993, 995, 443 and 465 to setup MS-Exchange. I don't have an inhouse IT guy and this seems pretty straight-forward in theory but I can't figure it out I need to open ports 25, 993, 995, 443 and 465 to setup MS-Exchange.
View 5 Replies View RelatedWe have an ASA 5505. 5505 comes with two default vlans 1&2 with each of them marked as inside & outside respectively.My query is , if i do not want to use vlans on 5505 and only want to use the Ethernet ports as pure physical layer 3 ports, is it possible?i.e. i want to assign a layer 3 ip address on eth0/0 and eth0/1 and make them as the inside & outside interfaces rather than vlans. is it possible to do away with vlans in 5505 & will it work otherwise?
View 3 Replies View RelatedWe have setup new ip camera system and as per our vendor to access the camera from outside we need to open,TCP ports and in firewall and forward to our camera server.
Let say our public ip address is 207.114.111.22 and our local ip address for the camera is 11.11.1.30. We have cisco asa 5510.
I just finished implementing a VOIP install and I am trying to setup some softphones and in order to allow the softphones to work I need to open some specific ports for outbound. I am not a Cisco guy, I am a Windows Administrator that also has to maintain my Cisco infrastructure.
View 3 Replies View Relatedwhat are default ports are open on asa 5520 from outside interface (Zero level Security ) to inside interface (Security level 100)
View 3 Replies View RelatedI have an ASA 5501 running latest code. Per the article at [URL], I need to open the below ports. I have 5 Xboxes (when people come over) and they all have a static IP. My network is 192.168.0.x and is a /24 network.Xbox LIVE requires the following ports to be open: Port 88 (UDP)Port 3074 (UDP and TCP)Port 53 (UDP and TCP)Port 80 (TCP)port 1863 (UDP and TCP) (Kinnect) I defined the various network ports as a service and then created 5 hosts called xbox1, 2, etc with a static IP. I dont have access from the command line (forgot telnet and ssh passwords) , so from the gui, what do I do next?
View 7 Replies View RelatedI need to open the following ports on a pix:
-tcp 3230 to 3235
-udp 3230 to 3253
How do I open the ports?
I need top open ports 80, 443 and 1882 to a specific external client (IP address).
View 8 Replies View RelatedI got a situation here for Nat-ed IPs i configured. I expected to open some ports on the interface to allow certain traffics to pass through, yet there are some of them are failed. Down is my current config.
object-group service DM_INLINE_SERVICE_1
service-object icmp
service-object tcp destination eq https
[Code]....
The only ports opened are 443, www, 3389 while ports domain, 5061,3478,3389. how to open domain, 5061, 3478, and 3389 ports on my ASA .
-I need to configure the following on my PIX:
TCP port 2195 - outbound
-TCP port 2196 - inbound
How would I configure this via ASDM?
I have the port numbers but do not know how to proceed from there. Router is a WRT160N V2.
View 9 Replies View RelatedI am trying to open port 52199 on my ASA 5505 I have gone to firewall, access rules and then add tcpip.Not sure if that is the correct place but cannot get it to work?
View 1 Replies View Relatedwhen I want to let email to come through the ASA5505 from outside to DMZ and Inside network, are the below command lines correct and good enough?
access-list outside_DMZ extended permit tcp outside-network-ip dmz-network-ip eq imap4
access-list outside_DMZ extended permit tcp outside-network-ip dmz-network-ip eq pop3
access-list outside_DMZ extended permit tcp outside-network-ip dmz-network-ip eq smtp
access-list outside_inside extended permit tcp outside-network-ip inside-network-ip eq imap4
access-list outside_inside extended permit tcp outside-network-ip inside-network-ip eq pop3
[code]....
Are there any other TCP ports want to be allowed and other command lines need to be added?
I just installed a Cisco ASA 5505 in my company's network,however the network became so slow and many websites cannot be opened or it takes toolong to open (yahoo, hotmail etc.) resulting to a request time out sometimes.
Here is my configuration:
ASA Version 8.2(1) !hostname xxxxxxenable password xxxxxx encryptedpasswd xxxxx encryptednames!interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 !interface Vlan2 nameif outside security-level 0 ip address
[Code].....
We have a client that is running a PC on a internet over satellite. To avoid any unessecery traffic over the satellite link (data traffic is quite expensive), we've suggested to use a 5505, as we had one handy already.
So basically what we wanted was to block everything outgoing and everything ingoing, except for example port 22 (ssh).
But I'm struggling a bit, since this is my first cisco router to be configured.
My interfaces are as follows.
Outside - DHCP
Inside (port 1) - 192.168.1.1
I'm only running ipv4.
in ASDM I made a static NAT rule for port 22, being forwarded to 192.168.1.5 (the computer)
in Access rules I made under outside (incomming rules) source=any destination=outside service=ssh action=permit
But when I try to add further rules to block everything else, it takes the SSH on port 22 with it. How should I do this the easiest way?
the hardware setup is pretty straight forward.
sat-terminal(with IP 192.168.0.1 running DHCP) -> 5505 (outside IP=DHCP - inside IP=192.168.1.1) -> computer (IP=192.168.1.5)
I've an ASA 5505 as my gateway for my internet at home. I've one public IP, so I use Port Address translatetion for my internal clients.
Now i wanna setup a FTP server, on a internal client. I will use Filezilla FTP server. I'm running the FTP server in passive mode, since the FTP server would be behind my ASA firewall/nat device.
I need 50 ports for the passive mode to be running.
I will use port range 50000-50050. I can easy make a firewall rule (access-list) that permit that port range.
But how do I PAT(NAT) a port-range on the ASA device? I can only figure out how to NAT one port at the time.
I need to forward some ports for remote desktop and remote outlook which I host on an internal server. I have looked all over the web and got close, but no hints on how to do it in the asa 8.2. there is an 8.3 guide, but it is just different enough to not work. I am new to this device and cli.
View 3 Replies View RelatedI am trying to configure a new 5505 but I am having difficulties opening ports that allow traffic in from the outside. My setup is Comcast Business Modem (w/ single static IP) -> ASA (10.0.0.1) -> (dumb) Switch -> NAS (10.0.0.10). I am attemping to open port 5001 to the NAS. I am very new to IOS so I have mostly been working in ASDM. Not sure if I am overcomplicating this for myself or what but I am stuck.
My running config is -
ASA Version 8.2(5)
!
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
[Code].....
When I do an NMAP scan against my ASA 5505 on it's internal interface's IP address, it appears to be listening on all TCP ports. If I do it from across a VPN tunnel, the ports show as open according to NMAP, if I do the scan from the local subnet they show up as unknown. I'm running 8.0.4 code on this ASA.
View 1 Replies View RelatedWe've read everything about inspecting SIP packets and allowing them to pass through on port 5060, the default SIP port. However, our setup requires the ASA 5505 to allow SIP on ports 5060, 5160 and 5260.
Is this possible with the ASA 5505? If it's not, it would be a blocking issue for us to move forward with ASA appliances. We are currently investigating in a lab environment and really having difficulties configuring it to facilitate full SIP functionality.
I have an ASA 5505 running 8.4(1), and I'm configuring it with ASDM 6.4(1). The outside interface is configured with a single static address. I have a few services port forwarded sucessfully to three different servers on the inside network.
I need to make a media proxy on a SIP server available to the outside. It requires a large range of forwarded UDP ports for the media channels.
I tried adding a network object NAT rule like the others I'm already using to forward HTTP and RDP. I entered a range of ports for the real port and the mapped port using the syntax 60000-60999. ASDM accepted it, but the NAT rule list displays "Any" in the service column. When I apply the change, I get the following error:
nat (inside,outside) static interface service tcp 60000-60999 60000-60999
^
ERROR: % Invalid input detected at '^' marker.
How do I forward a large range of UDP ports from the outside interface to a single server on my inside network? I'd like to use ASDM, but I can switch to the CLI if that works better.
I am in search of a new routers. I don't have any special task to do. Just the flow of maximum 2mb/sec data and some times video conference. However I need the Voip solution as well. I just got excited on the cisco ASA 5505 product. Can this fulfill my requirements. Can this work as the router 1841. Does this support DMVPN, SSL VPN and dynamic routing. Can I upgrade the IOS for dynamic routing purpose. Do you recommend to purchase this produe act or not instead of router ? What are the limitations of this product. If I purchase this I can use this as an router as well as strong security solution. How many ports are available for traffic flow in ASA 5505. Are all routed mode or some of them switch port.
View 1 Replies View Related I am trying to open up 3 TCP ports in Cisco ASDM Launcher:
16000
16001
8098
And have a Cisco ASA 5505 Router. I need these ports open in order for a software that I have installed on the server to communicate with my local client computers for my business, The software is installed on Windows 2008 Server Standard Edition and was installed with MicrosoftSQL 2005. The software and Microsft SQL 2005 is pretty much installed and just requires this last step in order for the server to be connected to the local computers. In order to resolve this, I have gone to.
I am used to setting up access-lists on outside interfaces with ip addresses that are static. I have recently been given a site that is using a dyndns.org client for name to ip address resolution on an outside interface that is dhcp assigned. I created an access-list to open up ports 41794 and 41795 to an engineering application but everytime I try to connect from the outside I get a syn timeout. The application works when inside the lan. Basically I want to allow outside connections from anywhere on the outside to go to ports 41794 and 41795. I am running a Cisco ASA 5505 on version 7.2(4) Below is my conifg. what I may have misconfigured?
: Saved:ASA Version 7.2(4)!names!interface Vlan1 nameif inside security-level 100 ip address 172.31.2.1 255.255.255.0!interface Vlan2 nameif outside security-level 0 ip address dhcp setroute!interface Ethernet0/0 switchport access vlan 2!interface
[Code].....
I'm stuck at asa 5505 nat, port forwarding configuration Here is what i need:
host1: 192.168.1.1 service tcp/100 >>>>> public ip 1.1.1.1 service tcp/100
host2: 192.168.1.2 service tcp/200 >>>>> public ip 1.1.1.1 service tcp/200
host3: 192.168.1.3 service tcp/300 >>>>> public ip 1.1.1.1 service tcp/300
So people from remote just need to use 1.1.1.1 public ip to access all the ports on three different inside server.I can do this on my old ASA 5505 with 8.0(4). Looks like there're lots of change from 8.0 to 8.4.
I have a Cisco 877 connected to a VSAT modem, and I can't open ports outside, I dont know why?The Cisco 877 Fa0 port is connected to the VSAT modem at VLAN9, and the rerst of ports are connected to the local lan network at Vlan2. I can enter to Internet, but I can't open port outside. ADSL over pots is not used here.I need to open port 81 for ip address 192.168.1.130 and I dont know why this isn't working. Also if I do: sh ip nat translations I see this:
sh ip nat translations
cisco877#sh ip nat translations
Pro Inside global Inside local Outside local Outside global
tcp 172.30.xx.122:81 192.168.1.130:81 --- ---
udp 172.30.xx.122:81 192.168.1.130:81 --- ---
[code].....
How can I allow all ports to be open? I don't really want my 1811 to block any traffic. I tried the command access-list 1 permit any which allows me to surf the internet, but when I check my web server, and port 3389 (Remote desktop) on yougetsignal.com it says those ports are blocked.
View 6 Replies View RelatedWe have a client that has a Cisco 1801W Firewall that is setup as a site to site VPN terminating to a Cisco ASA 5505. The tunnel is up and established, I can ping from both sides of the tunnel.
The problem is the clients behind the Cisco ASA (192.168.2.x) cannot reach certain ports behind the Router (192.168.1.x). The main thing we're trying to do is browse via UNC path (ex: \192.168.1.120 from a 192.168.2.x machine).
I got 3389 working after I changed the - ip nat inside source static tcp 192.168.1.120 3389 y.y.x.x 3389 route-map DM_RMAP_1 extendable Modified the command to include the public IP instead of interface FastEthernet0
I believe it has something to do with the way NAT and route-maps are setup currently but I'm not familar enough with them to make the changes. I worked with Cisco to ensure the VPN tunnel was fine and it's something security related on the Router.
Here is the configuration (removed a few lines not necessary. y.y.x.x = WAN IP of Router x.x.y.y = WAN IP of ASA).
Building configuration...
Current configuration : 23648 bytes
!
version 12.4
no service pad
[Code].....
I'm setting up a second exchange 2010 server at a DR location and have been experiencing some problems. The two sites are connected via a pair of ASA5510's using the point to point VPN. I want to rules out any possible VPN issues that may be blocking ports and wanted to see if there is an easy way to do this and simply allow all traffic without any restrictions between the two ASAs. I've attached the scrubbed configs here...Ewing is the primary site and DBSi is the DR site.
View 2 Replies View Relatedwhat command should I use to see all open TCP and UDP ports on my router?
View 2 Replies View Related