Cisco Firewall :: Allow SIP On Multiple Ports Not Only 5060 (ASA 5505)
May 14, 2012
We've read everything about inspecting SIP packets and allowing them to pass through on port 5060, the default SIP port. However, our setup requires the ASA 5505 to allow SIP on ports 5060, 5160 and 5260.
Is this possible with the ASA 5505? If it's not, it would be a blocking issue for us to move forward with ASA appliances. We are currently investigating in a lab environment and really having difficulties configuring it to facilitate full SIP functionality.
View 1 Replies
ADVERTISEMENT
Mar 11, 2012
We have a Cisco secure VPN site to site tunnel between the 2 locations.Which ports are need to open on tunnel so that users can successfully use OCS over the site to site VPN tunnel.All the users are havning the main brach AD account.Using Wireshark captured the packets, found only port TCP 5060, after allowing this port over tunnel I can see the authentication window.The user authentication fails. Already port 3389, 80, 443 are allowed.The main requirement is to only have the Chat, Group Chat and file transfer. Not require AV traffic.OCS is using TCP. no TLS is configured.
View 1 Replies
View Related
Jun 22, 2011
I'm stuck at asa 5505 nat, port forwarding configuration Here is what i need:
host1: 192.168.1.1 service tcp/100 >>>>> public ip 1.1.1.1 service tcp/100
host2: 192.168.1.2 service tcp/200 >>>>> public ip 1.1.1.1 service tcp/200
host3: 192.168.1.3 service tcp/300 >>>>> public ip 1.1.1.1 service tcp/300
So people from remote just need to use 1.1.1.1 public ip to access all the ports on three different inside server.I can do this on my old ASA 5505 with 8.0(4). Looks like there're lots of change from 8.0 to 8.4.
View 7 Replies
View Related
Jun 9, 2013
We have an ASA 5505. 5505 comes with two default vlans 1&2 with each of them marked as inside & outside respectively.My query is , if i do not want to use vlans on 5505 and only want to use the Ethernet ports as pure physical layer 3 ports, is it possible?i.e. i want to assign a layer 3 ip address on eth0/0 and eth0/1 and make them as the inside & outside interfaces rather than vlans. is it possible to do away with vlans in 5505 & will it work otherwise?
View 3 Replies
View Related
Nov 13, 2012
We have a costumer who has an asterix PBX behind an ASA i configured, the PBX i did not configure, we have several customers with the same setup. Today we have noticed that there PBX got hacked and was making calls to very expensive phone extensions. The guy who configured the PBX is saying that its the ASA who got hacked. In my opinion it is not the ASA that got hacked but i think there is something going on on the internal network.
They from th PBX says when he scans the IP of the customer who got hacked he sees port 5060 sip is open. but in the ASA ther is no port forwarding on that port, how is this possible?I also scanned it myself and it says port 5060 is open, which is weird because there is no port forwarding on port 5060.
View 11 Replies
View Related
May 21, 2013
We are migrating from a nother brand to an ASA Cluster running 8.4.5
We have a web-server on an inside interface listening on a non standard port - 20111. We have created a static NAT translating the public ip to the private, so If I do http://public-ip:20111 it works. (we are using a seperate public IP for this service only).
Now I need to create a NAT rule that will forward requests on BOTH port 80 and 443 to the same private ip and the same port number (20111)
The Private address is 10.99.250.20 and the "public" (I've replaced it in this example) is 172.16.16.16 I have managed to create a NAT that will translate 443 to 20111:
object network 10.99.250.20 nat (Private-DMZ,Outside) static 172.16.16.16 service tcp 20111 https
But if I try to add another rule like: nat (Private-DMZ,Outside) static 172.16.16.16 service tcp 20111 http It will simply replace the first one.
Is it possible to redirect both 80 and 443 from outside to the same port number and same IP on the inside?
View 1 Replies
View Related
Apr 15, 2013
We have a client that is running a PC on a internet over satellite. To avoid any unessecery traffic over the satellite link (data traffic is quite expensive), we've suggested to use a 5505, as we had one handy already.
So basically what we wanted was to block everything outgoing and everything ingoing, except for example port 22 (ssh).
But I'm struggling a bit, since this is my first cisco router to be configured.
My interfaces are as follows.
Outside - DHCP
Inside (port 1) - 192.168.1.1
I'm only running ipv4.
in ASDM I made a static NAT rule for port 22, being forwarded to 192.168.1.5 (the computer)
in Access rules I made under outside (incomming rules) source=any destination=outside service=ssh action=permit
But when I try to add further rules to block everything else, it takes the SSH on port 22 with it. How should I do this the easiest way?
the hardware setup is pretty straight forward.
sat-terminal(with IP 192.168.0.1 running DHCP) -> 5505 (outside IP=DHCP - inside IP=192.168.1.1) -> computer (IP=192.168.1.5)
View 24 Replies
View Related
May 31, 2011
I've an ASA 5505 as my gateway for my internet at home. I've one public IP, so I use Port Address translatetion for my internal clients.
Now i wanna setup a FTP server, on a internal client. I will use Filezilla FTP server. I'm running the FTP server in passive mode, since the FTP server would be behind my ASA firewall/nat device.
I need 50 ports for the passive mode to be running.
I will use port range 50000-50050. I can easy make a firewall rule (access-list) that permit that port range.
But how do I PAT(NAT) a port-range on the ASA device? I can only figure out how to NAT one port at the time.
View 2 Replies
View Related
May 9, 2013
I have an ASA 5505 with ASA version 7.2(2) and ASDM version 5.2(2) and I am attempting to open ports 88 and 5445 and forward them to the IP address of my DVR. This is all new for me. I see several posts for other software version to do this same thing but my version appears to be older?
View 1 Replies
View Related
Nov 7, 2011
I need to forward some ports for remote desktop and remote outlook which I host on an internal server. I have looked all over the web and got close, but no hints on how to do it in the asa 8.2. there is an 8.3 guide, but it is just different enough to not work. I am new to this device and cli.
View 3 Replies
View Related
Jan 2, 2013
I am trying to configure a new 5505 but I am having difficulties opening ports that allow traffic in from the outside. My setup is Comcast Business Modem (w/ single static IP) -> ASA (10.0.0.1) -> (dumb) Switch -> NAS (10.0.0.10). I am attemping to open port 5001 to the NAS. I am very new to IOS so I have mostly been working in ASDM. Not sure if I am overcomplicating this for myself or what but I am stuck.
My running config is -
ASA Version 8.2(5)
!
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
[Code].....
View 4 Replies
View Related
May 24, 2011
I have an ASA 5505 that I log into and currently only need a password to log onto the device. How do I set it up so a username is required as well?Another user needs to access the device. How would I set that up so they have to user their own credentials? I tried username apssword priv command and it does not work.
View 1 Replies
View Related
Dec 26, 2011
We have a working config with 1 external IP, we need to a second webserver (https) and it should be routed via a second public IP address. I already tried some suggestions from the community but haven't been able to find the solutions.
xxx.xxx.xxx.194 is going to the internal IP of 192.168.60.1 for OWA (https)
xxx.xxx.xxx.195 should go to a new webserver on 192.168.60.3
both server should be connected using SSL This is the current configuration :
ASA Version 8.3(1) !hostname fwdomain-name domain.localnames!interface Vlan1nameif insidesecurity-level 100ip address 192.168.60.250 255.255.255.0 !interface Vlan2nameif outsidesecurity-level 0ip address xxx.xxx.xxx.xxx 255.255.255.0 !interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!ftp mode passiveclock timezone CEST 1clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00dns server-group DefaultDNSdomain-name domain.localobject network obj_any subnet 0.0.0.0 0.0.0.0object network NETWORK_OBJ_192.168.70.0_26 subnet 192.168.70.0 255.255.255.192
[code].....
View 3 Replies
View Related
Sep 10, 2011
Attached is my updated ASA 5505 (8.4[2]) config. With this config, basically the "laptop" group works fine, but the leo and orion groups don't ever receive packets inbound. No DNS, nothing.
The laptop is windows, the other two are servers with two NICs. The interface cards are Intel Pro/1000s. I've been through everything including Vlan protocol conflicts and actually enabled the servers for 802.1(Q).
View 19 Replies
View Related
May 5, 2013
I'm working on setting up a PBX server in our office, and I'm having trouble getting a port opened for SIP on my ASA 5505.I created static NAT rule for SIP traffic from internal server to the outside IP address.I created access rules on outside interface to forward port 5060 to internal PBX server (192.168.1.8)I also disabled sip packet inspection on the ASA.I'm still receiving a message from the PBX that the firewall is configured incorrectly.
[code]....
View 5 Replies
View Related
Aug 7, 2011
When I do an NMAP scan against my ASA 5505 on it's internal interface's IP address, it appears to be listening on all TCP ports. If I do it from across a VPN tunnel, the ports show as open according to NMAP, if I do the scan from the local subnet they show up as unknown. I'm running 8.0.4 code on this ASA.
View 1 Replies
View Related
Mar 11, 2011
I have an ASA 5505 running 8.4(1), and I'm configuring it with ASDM 6.4(1). The outside interface is configured with a single static address. I have a few services port forwarded sucessfully to three different servers on the inside network.
I need to make a media proxy on a SIP server available to the outside. It requires a large range of forwarded UDP ports for the media channels.
I tried adding a network object NAT rule like the others I'm already using to forward HTTP and RDP. I entered a range of ports for the real port and the mapped port using the syntax 60000-60999. ASDM accepted it, but the NAT rule list displays "Any" in the service column. When I apply the change, I get the following error:
nat (inside,outside) static interface service tcp 60000-60999 60000-60999
^
ERROR: % Invalid input detected at '^' marker.
How do I forward a large range of UDP ports from the outside interface to a single server on my inside network? I'd like to use ASDM, but I can switch to the CLI if that works better.
View 3 Replies
View Related
May 22, 2011
I have 3 networks coming on DMZ (VPN) interface. Only one network is able to ping the DMZ interface. See below networks coming i on the DMZ.
10.132.24.0/2410.132.25.0/2410.132.26.0/24 Only the 10.132.26.0/24 netork works as it is in the same range as the DMZ interface.
allowing the other two networks to communicate. I've attched the diagram and configs for your perusal.
View 1 Replies
View Related
Dec 23, 2011
I want to configure multiple DHCP pool on ASA. that I create like
int e0/2
no shut
interface Ethernet0/2.10vlan 10nameif inside10security-level 100ip address 192.168.10.1 255.255.255.0
interface Ethernet0/2.20vlan 20 nameif inside20 security-level 100ip address 192.168.20.1 255.255.255.0
dhcpd address 192.168.10.10-192.168.10.254 inside10dhcpd dns x.x.x.x y.y.y.y interface inside10dhcpd enable inside10
dhcpd address 192.168.20.10-192.168.20.254 inside20dhcpd dns h.h.h.h z.z.z.z interface inside20dhcpd enable inside20
I have following query...
1. int e0/2 work as trunk port, is it? any special confiduration require other than dot1Q?
2. How can I configure inside interface? is it like,
access-group inside_access_in_1 in interface inside10
access-group inside_access_in_1 in interface inside10
3. How can I configure static NAT ?
4. How can i configured inside route?
5. How can I configured default NATing?
6. On which interface I access ASA? currently using inside interface.
View 5 Replies
View Related
Nov 8, 2011
I have a problem with a ASA 5505. He is crashing multiple times during the day. I've setup a syslog server en I'd noticed that the last two log notification were:
2011-11-08 12:28:19 Local4.Debug 10.0.0.254 %ASA-7-711002: Task ran for 27016 msec, Process = Dispatch Unit, PC = 84745ce, Traceback =
2011-11-08 12:28:19 Local4.Debug 10.0.0.254 %ASA-7-711002: Task ran for 27016 msec, Process = Dispatch Unit, PC = 84745ce, Traceback = 0x084745CE 0x08474942 0x08475511 0x08475DB7 0x08475EDA 0x08508D9B 0x0850908A 0x083AB5B8 0x083A1D55 0x080655C1 0x08895A19 0x08895AD0 0x08952194 0x08978450
It's a 5505 with a 10 user inside host license, wich incidentally is more.
View 2 Replies
View Related
Sep 13, 2012
We currently have 2 different ASA 5505 connect to our ASA5510. We want to VPN connect the 2 5505's to each other while still mantaining connection to our 5520. I have attached pdf of what we have. What we want is to connect traffic between the two 5505's so that devices in either location can talk to each other while still mantainig connection to the 5510.
View 13 Replies
View Related
Jan 7, 2013
I want to know with an ASA 5505 w/ Security Plus License I get up to 20 VLANS/Named Interfaces.I have a customer that is getting a new subnet of external IP addresses from their service provider and a different default gateway to accomodate re-hosting their datacenter at their main office instead of at a Colo. My question, when building out their new DMZ, can I have multiple route 0.0.0.0 commands?
Example.
Current Default Gateway 1.1.1.X
Internal hosts 192.168.1.0 use and are natted to 1.1.1.X
New Default Gateway for DMZ Servers 2.2.2.x
Internal hosts still use 1.1.1.X, but server hosts in 192.168.1.3 should use 2.2.2.X -- there are also a bunch of pre-existing static NAT rules for these servers such as 2.2.2.30 translates to 192.168.1.30.
I think I would accomplish this by using the following:
route inside 0.0.0.0 0.0.0.0 1.1.1.X
route DMZ 0.0.0.0 0.0.0.0 2.2.2.x
Would this be correct?
View 2 Replies
View Related
Sep 13, 2012
We currently have 2 different ASA 5505 connect to our ASA5510. We want to VPN connect the 2 5505's to each other while still mantaining connection to our 5520. I have attached pdf of what we have. What we want is to connect traffic between the two 5505's so that devices in either location can talk to each other while still mantainig connection to the 5510.
View 1 Replies
View Related
Sep 8, 2011
Is it possible to two or more public IP Addresses bound to a Cisco ASA 5505 running 8.4(2).
View 9 Replies
View Related
Jun 10, 2011
I am setting up a Cisco ASA 5505 first time for My organisation, I usually setup Cisco Router, I have 10 Static IP, & Have 6 Server (S-1, S-2, S-3, S-4, S-5, S-6), Traffic Should be pass through the ASA and is distributed to the destination server that is specified in the packet. LAN servers can be separated into discrete networks for security. For example, a private LAN for internal traffic accessed only via remote dial-in VPN sessions and Want to Configure DMZ for Server (S-4, S-5, S-6) that allows public web traffic.
I have Attached My Network Diagram I have some question,
1:- Can we Configure Multiple Static IP On ASA 5505 ?
2:- If Diagram is wrong what change need to be done ?
View 2 Replies
View Related
Sep 23, 2011
I have an ASA 5505 running 8.2(1), that is configured with three interfaces as follows:
Inside (security 100) 10.0.0.0 /24
Inside 2 (security 100) 192.168.0.0 /24
Outside (security 0) internet
Inside is connected to my internal network, inside 2 is connected to the network of a sister organization, outside is outside.
I'd like to be able to route between from inside to inside 2, and have NAT translate me to inside2's address.
I have inter-interface traffic configured, and when I use a NAT exemption, I can route fine. But the resources on network 2 must see my request as coming from the inside2 interface IP.
View 2 Replies
View Related
Feb 12, 2013
This is for an ASA 5505 with the base license...I have a situation where I will not have one interface in my outside VLAN, but instead I want to have interfaces 1-7 in my outside VLAN and interface0/0 in my inside VLAN.
Is this supported with the Base license, and if so how would I do this? Do I still just need to assign one IP address to the outside VLAN?
Or will I need to upgrade to the Security Plus license and put each interface in a separate outside VLAN, so in essence I would have 7 outside VLANs each with the same security level (0)?
My situation is that I have several partner networks that i want to "aggregate" thru my one ASA 5505. So each outside interface represents a separate partner (outside) network, each of which I want to get to from my inside network. Hence the many outside to one inside.
View 5 Replies
View Related
Oct 21, 2011
I am in search of a new routers. I don't have any special task to do. Just the flow of maximum 2mb/sec data and some times video conference. However I need the Voip solution as well. I just got excited on the cisco ASA 5505 product. Can this fulfill my requirements. Can this work as the router 1841. Does this support DMVPN, SSL VPN and dynamic routing. Can I upgrade the IOS for dynamic routing purpose. Do you recommend to purchase this produe act or not instead of router ? What are the limitations of this product. If I purchase this I can use this as an router as well as strong security solution. How many ports are available for traffic flow in ASA 5505. Are all routed mode or some of them switch port.
View 1 Replies
View Related
Jun 20, 2011
I am trying to open up 3 TCP ports in Cisco ASDM Launcher:
16000
16001
8098
And have a Cisco ASA 5505 Router. I need these ports open in order for a software that I have installed on the server to communicate with my local client computers for my business, The software is installed on Windows 2008 Server Standard Edition and was installed with MicrosoftSQL 2005. The software and Microsft SQL 2005 is pretty much installed and just requires this last step in order for the server to be connected to the local computers. In order to resolve this, I have gone to.
View 1 Replies
View Related
Oct 12, 2011
How to list ports open on Cisco ASA 5505 appliance? I have tried to see using Cisco ASDM launcher, but no luck.
View 1 Replies
View Related
Feb 25, 2011
I am used to setting up access-lists on outside interfaces with ip addresses that are static. I have recently been given a site that is using a dyndns.org client for name to ip address resolution on an outside interface that is dhcp assigned. I created an access-list to open up ports 41794 and 41795 to an engineering application but everytime I try to connect from the outside I get a syn timeout. The application works when inside the lan. Basically I want to allow outside connections from anywhere on the outside to go to ports 41794 and 41795. I am running a Cisco ASA 5505 on version 7.2(4) Below is my conifg. what I may have misconfigured?
: Saved:ASA Version 7.2(4)!names!interface Vlan1 nameif inside security-level 100 ip address 172.31.2.1 255.255.255.0!interface Vlan2 nameif outside security-level 0 ip address dhcp setroute!interface Ethernet0/0 switchport access vlan 2!interface
[Code].....
View 5 Replies
View Related
Oct 4, 2012
I want to configure multiple DHCP configuration on ASA 5505. I tried to create sub interface for different IP Pool but it was not configure on ASA 5505. is it possible to create subinterface on ASA 5505?
ASA 5505 IOS version: 8.3(1)
License: Security Plus
View 4 Replies
View Related
Aug 13, 2012
Our current cable ISP is having issues providing us with consistant connectivity. I would like to bring in a second ISP to allow my users to choose where they will connect to. There will be two dns names and i just want to to be able to choose between them.
Is this possible on the ASA5505? supporting two ISPs at one time for VPN on both?
View 3 Replies
View Related
