Cisco Firewall :: ASA 5505 / Multiple Interfaces In Outside VLAN?
Feb 12, 2013
This is for an ASA 5505 with the base license...I have a situation where I will not have one interface in my outside VLAN, but instead I want to have interfaces 1-7 in my outside VLAN and interface0/0 in my inside VLAN.
Is this supported with the Base license, and if so how would I do this? Do I still just need to assign one IP address to the outside VLAN?
Or will I need to upgrade to the Security Plus license and put each interface in a separate outside VLAN, so in essence I would have 7 outside VLANs each with the same security level (0)?
My situation is that I have several partner networks that i want to "aggregate" thru my one ASA 5505. So each outside interface represents a separate partner (outside) network, each of which I want to get to from my inside network. Hence the many outside to one inside.
View 5 Replies
ADVERTISEMENT
Sep 23, 2011
I have an ASA 5505 running 8.2(1), that is configured with three interfaces as follows:
Inside (security 100) 10.0.0.0 /24
Inside 2 (security 100) 192.168.0.0 /24
Outside (security 0) internet
Inside is connected to my internal network, inside 2 is connected to the network of a sister organization, outside is outside.
I'd like to be able to route between from inside to inside 2, and have NAT translate me to inside2's address.
I have inter-interface traffic configured, and when I use a NAT exemption, I can route fine. But the resources on network 2 must see my request as coming from the inside2 interface IP.
View 2 Replies
View Related
May 17, 2013
How can i enable Netflow for each Vlan Or interface indvidually in Cisco ASA? currently i have setup Netflow and only 2 interfaces are shwoing traffic for Netflow which are not even as my physical or Vlan interfaces . (see screen shot )
EscapeASA# sh interface ip brief
Interface IP-Address OK? Method Status Protocol
Internal-Data0/0 unassigned YES unset up up
[Code].....
View 9 Replies
View Related
Jan 15, 2013
Having upgraded to 8.3 from 8.2 I and read much about the differences , it seems that 8.3 deals with NAT in a much more managed method.However I am confused on how one would NAT a network object to multiple interfaces? i.e I know you can specficy a NAT adddress within the network object howeveer this only allows you to specific a single IP address.What if I want to talk accross multiple interfaces how would I specify this?
View 5 Replies
View Related
Jun 16, 2011
We have an ASA 5510 firewall. There are 4 ports on it configured as 2 outside, one inside, and one DMZ. We have two cable modems attached to the outside ports. Our plan is to have the "inside" port directed to one outside port/cable modem, and the DMZ port directed to the other outside port/cable modem.
We have been able to get the "inside-to-outside" setup to work but not the "DMZ-to-outside" setup (at least at the same time).First off, is this possible? If so, what are we likely missing - some way to have a second default route for the DMZ?(My manager is the "Cisco person" here, not me, so I may not have enough info.
View 1 Replies
View Related
Oct 10, 2011
I've been trying to figure this one out for quite a while. I currently have 2 inside interfaces (data, phone) and I am moving to 3 inside interfaces (servers, workstations, phones). I have not been able to get any traffic between the interfaces. With the current setup it was not a major problem. With the new setup it will be a major problem.
Below is a sanitized version of the config.
ASA Version 8.2(1)
!
hostname BOB
[Code].....
View 11 Replies
View Related
Nov 13, 2011
Unable to create VLAN interfaces in ASA 5510
View 1 Replies
View Related
Mar 20, 2012
Got new ASA5550, code 8.2.2 in flash, can't configure "nameif" or "ip address" on the interfaces: [code] These are all the options that I get! Another weird thing I noticed is "<system>" string in "show ver" top line: [code]
View 2 Replies
View Related
Jun 13, 2012
I am fairly new to configuring ASA's. I have an ASA 5505 with one outside interface and three inside interfaces (inside1, inside2, and management). I need inside1 and inside2 to be able to talk to eachother but cannot work out how to make this happen. They are both configured to the same security level and the 'Enable traffic between interfaces with same security level' box is ticked. I have also tried adding appropriate NAT and Access rules. The packet tracer suggests the rules are correct for allowing traffic flow between interfaces but obviosly this may not be the case.
View 14 Replies
View Related
Aug 18, 2011
It is my understanding that ACLs can only be bound to logical interfaces using the access-group command. However, is it possible to somehow apply ACLs simply based on the ASA's local Ethernet interface? For instance, consider the following:
Device A with IP 192.168.1.1/24 is connected to Ethernet0/0 on the ASA. Device B with IP 192.168.1.2/24 is connected to Ethernet0/1 on the ASA.
Since both devices are in the same subnet and presumably the same VLAN, is it possible to manipulate the traffic to and from physical Ethernet interfaces using ACLs in this manner?
My predicament is fairly simple:
Internet --- ASA --- ROUTER
|
DMZ
In addition to NAT, VPN, and various other tricks, my ASA is also routing traffic from my internal LAN and the Internet to servers in the DMZ configured on the ASA. Due to a combination of Internet and DMZ traffic, my relatively slow ASA is struggling to route and thus becoming a bottleneck. My router is comparatively modest in terms of functionality when compared to the ASA but it is fast. My ideal solution would be to somehow harness the ASA's filtering capabilities for my DMZ but use the router to get traffic to and from my internal LAN into the DMZ without using the ASA to route it.
Additionally, it is worth noting that my DMZ is fairly restrictive so using protected or isolated ports would not quite work for me.
View 1 Replies
View Related
Nov 9, 2011
I trying to allow traffic between 2 inside interfaces with the same security level. VLAN1 and VLAN15. The are on different physical ports on the ASA. I tried to configure this through the GUI Web interface and checked ' enable traffic between two or more interfaces with the same security levels'. With this ASA version, I do not need NAT to allow this, correct?
ASA Version 8.2(1)
!
hostname ciscoasa
[Code].....
View 1 Replies
View Related
Mar 6, 2011
My customer is running an ASA5505 with 8.3 code.
The have a somewhat flaky proxy between their inside LAN and the firewall. I'd like to have a configuration as follows:
LAN > Proxy > VLAN 1 (eth0/2) on ASA
and
LAN > VLAN 1 (eth0/3) on ASA
So that in the event of Proxy failure (let's just say it loses power) the eth0/3 interface will kick in.
This appears to be easily configured according to the documentation:
"The following example creates two redundant interfaces:
hostname(config)# interface redundant 1
hostname(config-if)# member-interface gigabitethernet 0/0
hostname(config-if)# member-interface gigabitethernet 0/1
hostname(config-if)# interface redundant 2
hostname(config-if)# member-interface gigabitethernet 0/2
hostname(config-if)# member-interface gigabitethernet 0/3"
But these commands don't seem to be available on a 5505.
View 7 Replies
View Related
May 13, 2013
I am trying to build a new network from scratch, I have the WLC 5508 w/ Aironet 3600e APs connected to my Netgear Smart Switches and a Linksys RV082 router that I'm using as my DHCP server with several VLANs for several stuff on my Switches.
I have 2 questions:
1. Can I have 5 Interfaces configured on 5 different VLANs, each SSID on each a different Port:
Port 1: Controller management only=> 192.168.x.x /24
Port 2: SSID 1: WiFi Internal=> 172.16.x.x/12 (Radius Auth with no sharing)
Port 3: SSID 2: WiFi Internal w/ sharing=> 192.168.x.x/24 (Radius Auth with sharing)
Port 4 :SSID 3: WiFi Guest=> 10.0.x.x/8 (Web Auth)
Port 5: SSID 4: WiFi IT=> 192.168.x.x/24 ( Radius or certificate Auth with access to the controller management interface)
2. How can I use the Controller as the DHCP server for all the WiFi traffic, and how should that be configured to work with my other DHCP server?
View 3 Replies
View Related
Jan 13, 2013
Whether it is possible to have same vlan on multiple interface on ASA 5510 and higher models ?
View 2 Replies
View Related
Feb 15, 2013
We have two Cisco 5505 firewalls connecting to two ISP's . The two internal LAN's on the firewalls are 192.168.184.0/24 & 192.168.186.0/24. We also have a Cisco C3560x layer3 switch with vlan interfaces 184.3 & 186.3. We have two DGS-3100 Dlink layer 2 switches connecting our users to the Layer 3. Ip routing is enabled for intervlan communication & I can reach the Switch interfaces & firewall gateways from machines on both on the vlans.We have pbr enabled on the 3560 & users only on the .186 network can get to the internet. The switch is running the ipservices license & the sdm template is "desktop routing" .
Users on the .184 cannot access the internet but we can ping the layer3 interface & the firewall gateway. [code]
View 20 Replies
View Related
May 3, 2011
I have been working with ASA 5510,20,40,80 but not with 5505 this vlan and its interfaces are quite confusing.Just want to know how it works and its connectivity to Cisco Switch.Do i have to put the interface of the switch in the same vlan as i am creating the interface vlan in firewall ?Now the switch port connecting to this Eth1 interface should also be in the same vlan ? i.e vlan3 ?? or it will be in trunk ? The default configuration shows the eth0 with no access vlan and interface eth1 with access vlan 2... does it mean the eth0 is in vlan1 ? (Nativ Vlan ) ???
View 4 Replies
View Related
May 24, 2011
I have an ASA 5505 that I log into and currently only need a password to log onto the device. How do I set it up so a username is required as well?Another user needs to access the device. How would I set that up so they have to user their own credentials? I tried username apssword priv command and it does not work.
View 1 Replies
View Related
Dec 26, 2011
We have a working config with 1 external IP, we need to a second webserver (https) and it should be routed via a second public IP address. I already tried some suggestions from the community but haven't been able to find the solutions.
xxx.xxx.xxx.194 is going to the internal IP of 192.168.60.1 for OWA (https)
xxx.xxx.xxx.195 should go to a new webserver on 192.168.60.3
both server should be connected using SSL This is the current configuration :
ASA Version 8.3(1) !hostname fwdomain-name domain.localnames!interface Vlan1nameif insidesecurity-level 100ip address 192.168.60.250 255.255.255.0 !interface Vlan2nameif outsidesecurity-level 0ip address xxx.xxx.xxx.xxx 255.255.255.0 !interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!ftp mode passiveclock timezone CEST 1clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00dns server-group DefaultDNSdomain-name domain.localobject network obj_any subnet 0.0.0.0 0.0.0.0object network NETWORK_OBJ_192.168.70.0_26 subnet 192.168.70.0 255.255.255.192
[code].....
View 3 Replies
View Related
Sep 10, 2011
Attached is my updated ASA 5505 (8.4[2]) config. With this config, basically the "laptop" group works fine, but the leo and orion groups don't ever receive packets inbound. No DNS, nothing.
The laptop is windows, the other two are servers with two NICs. The interface cards are Intel Pro/1000s. I've been through everything including Vlan protocol conflicts and actually enabled the servers for 802.1(Q).
View 19 Replies
View Related
May 22, 2011
I have 3 networks coming on DMZ (VPN) interface. Only one network is able to ping the DMZ interface. See below networks coming i on the DMZ.
10.132.24.0/2410.132.25.0/2410.132.26.0/24 Only the 10.132.26.0/24 netork works as it is in the same range as the DMZ interface.
allowing the other two networks to communicate. I've attched the diagram and configs for your perusal.
View 1 Replies
View Related
Dec 23, 2011
I want to configure multiple DHCP pool on ASA. that I create like
int e0/2
no shut
interface Ethernet0/2.10vlan 10nameif inside10security-level 100ip address 192.168.10.1 255.255.255.0
interface Ethernet0/2.20vlan 20 nameif inside20 security-level 100ip address 192.168.20.1 255.255.255.0
dhcpd address 192.168.10.10-192.168.10.254 inside10dhcpd dns x.x.x.x y.y.y.y interface inside10dhcpd enable inside10
dhcpd address 192.168.20.10-192.168.20.254 inside20dhcpd dns h.h.h.h z.z.z.z interface inside20dhcpd enable inside20
I have following query...
1. int e0/2 work as trunk port, is it? any special confiduration require other than dot1Q?
2. How can I configure inside interface? is it like,
access-group inside_access_in_1 in interface inside10
access-group inside_access_in_1 in interface inside10
3. How can I configure static NAT ?
4. How can i configured inside route?
5. How can I configured default NATing?
6. On which interface I access ASA? currently using inside interface.
View 5 Replies
View Related
Nov 8, 2011
I have a problem with a ASA 5505. He is crashing multiple times during the day. I've setup a syslog server en I'd noticed that the last two log notification were:
2011-11-08 12:28:19 Local4.Debug 10.0.0.254 %ASA-7-711002: Task ran for 27016 msec, Process = Dispatch Unit, PC = 84745ce, Traceback =
2011-11-08 12:28:19 Local4.Debug 10.0.0.254 %ASA-7-711002: Task ran for 27016 msec, Process = Dispatch Unit, PC = 84745ce, Traceback = 0x084745CE 0x08474942 0x08475511 0x08475DB7 0x08475EDA 0x08508D9B 0x0850908A 0x083AB5B8 0x083A1D55 0x080655C1 0x08895A19 0x08895AD0 0x08952194 0x08978450
It's a 5505 with a 10 user inside host license, wich incidentally is more.
View 2 Replies
View Related
Sep 13, 2012
We currently have 2 different ASA 5505 connect to our ASA5510. We want to VPN connect the 2 5505's to each other while still mantaining connection to our 5520. I have attached pdf of what we have. What we want is to connect traffic between the two 5505's so that devices in either location can talk to each other while still mantainig connection to the 5510.
View 13 Replies
View Related
Jan 7, 2013
I want to know with an ASA 5505 w/ Security Plus License I get up to 20 VLANS/Named Interfaces.I have a customer that is getting a new subnet of external IP addresses from their service provider and a different default gateway to accomodate re-hosting their datacenter at their main office instead of at a Colo. My question, when building out their new DMZ, can I have multiple route 0.0.0.0 commands?
Example.
Current Default Gateway 1.1.1.X
Internal hosts 192.168.1.0 use and are natted to 1.1.1.X
New Default Gateway for DMZ Servers 2.2.2.x
Internal hosts still use 1.1.1.X, but server hosts in 192.168.1.3 should use 2.2.2.X -- there are also a bunch of pre-existing static NAT rules for these servers such as 2.2.2.30 translates to 192.168.1.30.
I think I would accomplish this by using the following:
route inside 0.0.0.0 0.0.0.0 1.1.1.X
route DMZ 0.0.0.0 0.0.0.0 2.2.2.x
Would this be correct?
View 2 Replies
View Related
Sep 13, 2012
We currently have 2 different ASA 5505 connect to our ASA5510. We want to VPN connect the 2 5505's to each other while still mantaining connection to our 5520. I have attached pdf of what we have. What we want is to connect traffic between the two 5505's so that devices in either location can talk to each other while still mantainig connection to the 5510.
View 1 Replies
View Related
Sep 8, 2011
Is it possible to two or more public IP Addresses bound to a Cisco ASA 5505 running 8.4(2).
View 9 Replies
View Related
Jun 10, 2011
I am setting up a Cisco ASA 5505 first time for My organisation, I usually setup Cisco Router, I have 10 Static IP, & Have 6 Server (S-1, S-2, S-3, S-4, S-5, S-6), Traffic Should be pass through the ASA and is distributed to the destination server that is specified in the packet. LAN servers can be separated into discrete networks for security. For example, a private LAN for internal traffic accessed only via remote dial-in VPN sessions and Want to Configure DMZ for Server (S-4, S-5, S-6) that allows public web traffic.
I have Attached My Network Diagram I have some question,
1:- Can we Configure Multiple Static IP On ASA 5505 ?
2:- If Diagram is wrong what change need to be done ?
View 2 Replies
View Related
May 14, 2012
We've read everything about inspecting SIP packets and allowing them to pass through on port 5060, the default SIP port. However, our setup requires the ASA 5505 to allow SIP on ports 5060, 5160 and 5260.
Is this possible with the ASA 5505? If it's not, it would be a blocking issue for us to move forward with ASA appliances. We are currently investigating in a lab environment and really having difficulties configuring it to facilitate full SIP functionality.
View 1 Replies
View Related
Oct 4, 2012
I want to configure multiple DHCP configuration on ASA 5505. I tried to create sub interface for different IP Pool but it was not configure on ASA 5505. is it possible to create subinterface on ASA 5505?
ASA 5505 IOS version: 8.3(1)
License: Security Plus
View 4 Replies
View Related
Aug 13, 2012
Our current cable ISP is having issues providing us with consistant connectivity. I would like to bring in a second ISP to allow my users to choose where they will connect to. There will be two dns names and i just want to to be able to choose between them.
Is this possible on the ASA5505? supporting two ISPs at one time for VPN on both?
View 3 Replies
View Related
Jan 30, 2012
On our ASA 5505 We have a DMZ configured to use 2 ports, which are used by the mail and Web servers. So far everything works perfectly and this router has been very stable. Now I need to add more ports in order to accomodate prototype Web servers in the DMZ, but no more ports available on the Cisco. Looking through the ASDM though I noticed the DMZ seems to be configured as "VLAN 5", sure enough with VLAN ID 5. So I tried creating a VLAN with ID 5 in my ProCurve switch, isolated from other VLANs. My theory being that plugging on of the the router's DMZ interfaced onto this VLAN would allow me to add my test servers. Well, this seems to work, but for only a very short time. I can get the landing page from my test server to display, and then everything slows down to a crawl and communication seems to be blocked. Out of curiosity, I tried to put my prod server and email server on the VLAN, together and separately, but the same thing happens. At first, I can ping the machines, then after a few request, everything stops responding.
View 1 Replies
View Related
Aug 15, 2011
I have a Cisco ASA 5505 that I have configured. The outside interface is vlan 2 and the inside interface is vlan 1. Port 0 of the ASA is configured to be in vlan 2 and is connected to the ISP provided subnet. Port 1 is connected to my private LAN subnet. I have an additional router connected to Port 2 for guest connectivity. Port 2 is configured to be a member of VLAN 2 so that it can access the ISP provided subnet. From the device connected to port 2 I can ping the vlan 2 interface address of the ASA and from the ASA I can ping the Default gateway of the ISP provided subnet. For some reason the router on port 2 cannot ping the default gateway of the ISP provided subnet. If the vlan were working the same as a vlan in a switch, I would expect to be able to do this. why it is not working or what I can do to get it working?
View 4 Replies
View Related
Mar 14, 2013
I have IOS 8.0(4) and the base 50 User License...will this config work? I have two networks; my home network, and my lab. I want to split my Internet connection between them, but keep the networks separate for the most part. Will my license allow this config since I can't do DMZ?
interface Ethernet0/0
switchport access vlan 3
!
interface Ethernet0/1
switchport access vlan 1
!
interface Ethernet0/2
switchport access vlan 2
[code]....
View 1 Replies
View Related
