Cisco Firewall :: ASA 5505 Expanding A DMZ With VLAN
Jan 30, 2012
On our ASA 5505 We have a DMZ configured to use 2 ports, which are used by the mail and Web servers. So far everything works perfectly and this router has been very stable. Now I need to add more ports in order to accomodate prototype Web servers in the DMZ, but no more ports available on the Cisco. Looking through the ASDM though I noticed the DMZ seems to be configured as "VLAN 5", sure enough with VLAN ID 5. So I tried creating a VLAN with ID 5 in my ProCurve switch, isolated from other VLANs. My theory being that plugging on of the the router's DMZ interfaced onto this VLAN would allow me to add my test servers. Well, this seems to work, but for only a very short time. I can get the landing page from my test server to display, and then everything slows down to a crawl and communication seems to be blocked. Out of curiosity, I tried to put my prod server and email server on the VLAN, together and separately, but the same thing happens. At first, I can ping the machines, then after a few request, everything stops responding.
View 1 Replies
ADVERTISEMENT
May 3, 2011
I have been working with ASA 5510,20,40,80 but not with 5505 this vlan and its interfaces are quite confusing.Just want to know how it works and its connectivity to Cisco Switch.Do i have to put the interface of the switch in the same vlan as i am creating the interface vlan in firewall ?Now the switch port connecting to this Eth1 interface should also be in the same vlan ? i.e vlan3 ?? or it will be in trunk ? The default configuration shows the eth0 with no access vlan and interface eth1 with access vlan 2... does it mean the eth0 is in vlan1 ? (Nativ Vlan ) ???
View 4 Replies
View Related
Aug 15, 2011
I have a Cisco ASA 5505 that I have configured. The outside interface is vlan 2 and the inside interface is vlan 1. Port 0 of the ASA is configured to be in vlan 2 and is connected to the ISP provided subnet. Port 1 is connected to my private LAN subnet. I have an additional router connected to Port 2 for guest connectivity. Port 2 is configured to be a member of VLAN 2 so that it can access the ISP provided subnet. From the device connected to port 2 I can ping the vlan 2 interface address of the ASA and from the ASA I can ping the Default gateway of the ISP provided subnet. For some reason the router on port 2 cannot ping the default gateway of the ISP provided subnet. If the vlan were working the same as a vlan in a switch, I would expect to be able to do this. why it is not working or what I can do to get it working?
View 4 Replies
View Related
Mar 14, 2013
I have IOS 8.0(4) and the base 50 User License...will this config work? I have two networks; my home network, and my lab. I want to split my Internet connection between them, but keep the networks separate for the most part. Will my license allow this config since I can't do DMZ?
interface Ethernet0/0
switchport access vlan 3
!
interface Ethernet0/1
switchport access vlan 1
!
interface Ethernet0/2
switchport access vlan 2
[code]....
View 1 Replies
View Related
Jul 17, 2012
I am working on ASA 5505 with Base License that uses 3 VLAN's.
-My VLAN 1 is for used for my home network.
-VLAN 2 is connected to the public Internet and my IP gets assigned by ISP dynamically.
-VLAN 3 is DMZ where I will have few VM's that would need access to and from the Internet.
I am looking to work with following:
1) 172.16.0.2 that sits on DMZ will need to access public Internet over port 80
2) Permit access from the Internet over port 3389 to 172.16.0.2
3) Permit any host on private VLAN (192.168.0.0 network) to access 172.16.0.2 over the port 3389
4) Permit second VM on the DMZ VLAN let say 172.16.0.3 to access public Internet on all ports. Access in to this host is not permitted.
5) For some reason DHCP hosts are NOT getting DNS (8.8.8.8) entry when IP hets assigned or renew. I have a statements below but it is not working.
Also, if ACL rules for VoIP are written correctly. The goal is to permit these ports (SIP related) to access VoIP router. [code]
View 1 Replies
View Related
May 26, 2013
Site A:
ASA5520
VLAN data subnet 172.16.10.x/24
VLAN Voice subnet 10.0.0.x/24
Site B:
ASA5505 Base license
VLAN data subnet 192.168.10.x/24
VLAN Voice (restr) subnet 10.0.1.0/24
The callmanager is located on site A and needs to sent out DHCP-offers to site B through the VPN so the IP-phones can register to the callmanager. I got the VPN up and running for the data-subnet but i can't get traffic through the voice-subnet/VLAN.
Can the ASA's do the job or do I need to route traffic before the ASA's on both sides and sent it through the tunnel, configured both subnets as interesting traffic? Ofcourse the last situation I need to upgrade the license for the 5505 to gain more VLAN's.
View 4 Replies
View Related
Jul 8, 2012
Ive been readin all over the internet (including this site) trying to figure out if the asa can handle intervlan routing. Im not sure what I am missing on my config to get this to work. Ive read that it can work and Ive read that it cant work. How to get this to work on my asa 5505.
Here is my setup
Cable Modem ---> ASA (eth0/0)
(eth0/2) -->unmanaged switch for LAN connectivity
(eth0/3) --> Access point for wireless LAN connectivty
My config is attached
What I would like to do is be able to communicate between vlan3(LAN) and vlan4(Wireless LAN)
Whats strange is I can RDP between the two vlans but I cant ping or anything else.
View 20 Replies
View Related
Sep 2, 2012
ASA 5505, I got a security plus license which allows multiple VLANs.I want to be able to configure the ASA to allow only RDP session (One way) to another Switch where all the VLANs are. I've attached a pic of what I want but I'm struggling.
I looked at documentation saying you should have inside and outside interface but I'm not sure on this scenario.I've configured inside interface on ASA e0/1 and interface VLANs but not sure what to do between ASA and Switch?
View 2 Replies
View Related
Feb 12, 2013
This is for an ASA 5505 with the base license...I have a situation where I will not have one interface in my outside VLAN, but instead I want to have interfaces 1-7 in my outside VLAN and interface0/0 in my inside VLAN.
Is this supported with the Base license, and if so how would I do this? Do I still just need to assign one IP address to the outside VLAN?
Or will I need to upgrade to the Security Plus license and put each interface in a separate outside VLAN, so in essence I would have 7 outside VLANs each with the same security level (0)?
My situation is that I have several partner networks that i want to "aggregate" thru my one ASA 5505. So each outside interface represents a separate partner (outside) network, each of which I want to get to from my inside network. Hence the many outside to one inside.
View 5 Replies
View Related
May 17, 2013
How can i enable Netflow for each Vlan Or interface indvidually in Cisco ASA? currently i have setup Netflow and only 2 interfaces are shwoing traffic for Netflow which are not even as my physical or Vlan interfaces . (see screen shot )
EscapeASA# sh interface ip brief
Interface IP-Address OK? Method Status Protocol
Internal-Data0/0 unassigned YES unset up up
[Code].....
View 9 Replies
View Related
Oct 26, 2012
I have ASA 5505 with base license. I created 3rd vlan on it.it was created. but i am unable to assign IP to it. i assign ip address it takes it. But when i do sh int ip brief it does not show any ip.
Code...
View 7 Replies
View Related
Aug 7, 2012
We need to have one connection with less internet bandwidth assigned to it than all other other connections. Basically it is a separate conection from all others, incoming just from one switch port and separate VLAN.I know this can be done on the switch by limiting the bandwidth allocated to a port,
however, is it possible to have the speed limited down, just before it goes to the internet, ie, on the ASA, rather than doing it on the switch?The firewall is an ASA 5505.
View 2 Replies
View Related
May 4, 2011
I'm new to Cisco equipment much more familiar w/ Sonicwall w/ that said......I have a 5505 w/ Security Plus licensing
I have set up multiple VLANs as follows
VLAN 1 inside - still setup as 192.168.1.1 (will not be using this for our lan)
VLAN2 - outside
VLAN100 - LAN 10.1.1.1/24
[Code]....
If I do add all the VLANs above I understand I will probably have to make a trunk port since I only have 5 usable interfaces
View 12 Replies
View Related
Aug 7, 2011
ASA 5505 and DMZ and Base License,"For example, you have one VLAN assigned to the outside for Internet access, one VLAN assigned to an inside business network, and a third VLAN assigned to your home network. The home network does not need to access the business network, so you can use the no forward interface command on the home VLAN; the business network can access the home network, but the home network cannot access the business network." Page 6-17.
This is exactly what I need. Mail server in DMZ, full access from internet to DMZ, and from inside network to DMZ, no access from DZM to inside network. If I good understand, this is possible with base license.
I successfully configure, internet Access for DZM and inside network, Mail server can be accessed from internet, as well as RDP on inside network. But I have problem to configure communication from inside network to DMZ. [code]
View 13 Replies
View Related
Jun 8, 2011
I've got an ASA 5505 running 6.3 I've connected the management interface to our management vlan (which contains switch IPs, ilo's etc)Is there a way to allow access to this vlan from another?
View 1 Replies
View Related
Aug 30, 2012
My house is nicely wired for internet with access to the internet from every room via a wired connection. However, now that smartphones are starting to enter our lives and they like wifi, I would like to add wifi to my wired network. The router is in the basement and I would like to add wifi to the living room upstairs. So I don't think I am looking for a router/booster/repeater but some other piece of equipment that can be plugged into a ethernet plug in the wall of the living room and broadcast from there. I have used Connectify but that requires a laptop to be on all the time so I was hoping for something smaller and easier.
View 1 Replies
View Related
May 2, 2013
Is it possible to add another NIC to the Cisco 3315 NAC appliance. It ships with Four ethernet interfaces, but would like to add at least 1 extra interface i.e. PCI card if possible.
View 1 Replies
View Related
Jan 3, 2012
My router (D-LINK DIR-655) is in the living room under my TV in a cabinet with the lid closed (i would like to keep it that way, because the DIR-655 has the brightest led lights ever). My ground floor coverage is decent except in my back yard where i only get 1 bar or lose signal (we are talking about 10-15m distance). I am using mixed G & N mode with auto 20/40 MHz. In the past i had full bars in my back yard using a Linksys WRT54GL (Wireless-G) with DD-WRT firmware.
I have the following devices connected on my router: ISP MODEM / DREAMBOX / HTPC / DNS-325 / TV
1st Floor: I don't have any wireless coverage here, sometimes one bar but keeps dropping. This is where i would like to expand my wireless coverage in the whole floor.
2nd Floor: Here is my attic which i don't basically need any wireless. My main concern is in the 1st floor.
View 9 Replies
View Related
Dec 10, 2011
Have a network set up but it only works on the printer and public folders. Want the network to give me full access to all computers. Desktops and laptop run Win 7. Am familiar with computers. Was an electronics tech, NOT a computer tech, for 15 years and have upgraded / built several computers for family and friends for more than 10 years.
My guess is it would be a lot easier to put what I want to share in a public folder but there is only my wife and me. Guests log onto a "guest" account on the router and do not think they would have access to any folders, public or private, no matter how the network is set up on the main account but not sure.
Don't remember specs exactly but all computers are less than 2 years old. Built desktops with AMD dual core and 6 GB ram. Laptop has Intel Centrino dual core with 4 GB ram. Router is Cisco Linksys E2000. Can get more specific specs if needed. Desktops are wired, laptop is wireless.
View 1 Replies
View Related
Jan 12, 2013
How do I submit an RFE (Request For Enhancement) to the Cisco SBR team to encourage them to implement the missing support for VLAN to VLAN firewall rules that was available in the RVS4000 (See [URL]) and that was supposedly added to a beta release of the RV220W firmware (See [URL])?
View 1 Replies
View Related
Aug 12, 2012
We have 6509 VSS with FWSM Module and we have created two context on it, one is INTERNALL CONTEXT othe is EXTERNALL Context? We have spanned various VLANS in switches and FWSM context level. All VLAN Gateways are configured in context level.
Activity description : We had planned migration of these devices into a new Datacenter, it was a planned activity. During migration of devices from one Dc to a new DC we broke the VSS and kept the primary running and removed the secondary switch and migrated this secondary to new DC and powered this device ON in the new DC and checked all the config was very much fine but this device was OFF network as secondary was brought to new DC just to limit the downtime during the primary switch movement.
During the activity ( Primary switch movement )We powered off the Primary switch and mean time before shifting into new Data center We had brought up secondary switch which was already existing in the DC was put live in the network and it was working fine without any issues.
Later we had moved Primary into new data center and tried to put into VSS with the secondary , during this period the secondary device into went into RECOVERY MODE and primary device was not responding and devices went off network and immediatly we removed the VSL link and brought up primary into production network without secondary online in the network ( Without VSS just stand alone switch ) network started working, but bringing up the primary we found that some of the VLANS in the FWSM was deleted and some VLAN had misconfiguration ( example : say original VLAN ip 10.200.112.1 has become 10.300.13.1 ) also some of the access list as well as SVI was deleted making configuration mismatch.
Wanted to know while syncronization b/n primary and secondary switch in VSS if we pull out VSL link would create this type of issues.
View 1 Replies
View Related
Dec 31, 2012
Region : UnitedStates
Model : TL-WR941ND
Hardware Version : Not Clear
Firmware Version : 3.12.5 Build 100929 Rel. 57776n
ISP :
I have a TP Link router model number: WR941N (under hardware version it says "v2/v3", that's why I put "not clear" under "hardware version" in the form). Whether it was possible to add even more slots for Port Forwarding for this router, the current hard limit is 16, and I would like to have more than that, what would be the procedure to do so?
View 2 Replies
View Related
Jul 29, 2011
I have a new e2500 router and want to use my old WRT54G2 to expand the range of the wireless to reach my detached garage. My house is wired with category 5e cabling, but not the garage, which is why i want to wireless to get expanded. I was hoping the the new e2500 would reach, but it doesn't. How I can do that?
View 6 Replies
View Related
Apr 14, 2013
I've got a 5505 and I'm getting a DHCP address from a cable modem. How can I show the DNS that the ASA is getting? show int vlan 2 is only givving me the IP and net mask.
View 2 Replies
View Related
Jan 17, 2012
I have an ASA 5505. I have configured Remote Access VPN so that users can connect to VPN and access my main VLAN (Inside). I would like to secure it so that when a user VPN's in, they are only allowed access to the HVAC vlan (Vlan 2) as seen in my configuration. Please note there is also a LAN- 2- LAN VPN which has been configured as well.
View 17 Replies
View Related
Aug 9, 2012
I'm trying to set up a Guest VLAN for wireless at a client site, and I feel like I'm missing something small in the configuration, since I can't ping any of the VLAN interfaces from my laptop when the address is statically set to something in the 172.20.100.x range.
I've pasted the configs for the ASA 5505 and the 6 switches below for convenience. Near as I can tell, all should be well. The ports are in trunking mode, the "show cdp neighbors" command returns the proper information, VLAN 100 exists on all the switches, etc.
Code:
ASA Version 7.2(4)
!
hostname ASA
domain-name xxxx.local
enable password Cj3LF.ehxXN3xVkxWcxd encrypted
passwd Cj3LF.ehxXN3xVkWcxd encrypted
[Code] ......
View 17 Replies
View Related
Apr 17, 2013
i have a asa5505 and sf300-48,in the sf300 have ip defult-gateway 192.168.1.93 and have internet in vlan2 but vlan 3 not work. ping from "vlan3" to "vlan2" its ok.
View 5 Replies
View Related
Oct 30, 2011
Having an issue getting my DMZ vlan working. Running my ASA5505 and i have configured e0/2 for DMZ w/ VLAN ID 3. Connected to my 2716 on port2.Inside e0/1 w/ VLAN ID 1. Connected to my 2716 on port1.
I am trying to get my DMZ Vlan to ports3&4 (LAG1) but when i assign the LAG group to PVID 3 i lose connectivity on VLAN1. I want to send both VLANs to that host because the teamed adaptor is used for Hyper-v Network Switch.
View 17 Replies
View Related
Apr 24, 2013
I have a Cisco ASA 5505 with the base License. I want to split my network and add a new Internet Access, the first network in Orange works fine. My question is how can i access the file server from the second network (192.168.X.0 /24) ? The 3 switches are Cisco SF300-24P.
View 7 Replies
View Related
Jan 19, 2013
I want to add new vlan in existing firewall group in 6500. I am confused if it will add new vlan or overwrite.. I am using ASASM module with 6500.
View 3 Replies
View Related
Sep 7, 2011
How I can actively monitor the interfaces and overall status of 2 x ASA 5500s in an Active/Standby configuration?
I can setup monitoring of the interfaces on the Active member but I'm not sure how to manage the Standby member?
View 1 Replies
View Related
Apr 24, 2012
We were having a discussion of ios firewall vs. asa for smaller clients(less than 50). On using ios firewall(zbf or cbac)and an asa 5505/5510. One of the arguments brought up on using ios firewall on the router is that a router will do an ip sla failover. I have configured a number of isr's for this and i know it works good.
View 1 Replies
View Related
Feb 19, 2012
I have a Cisco ASA 5505 in our office. We are currently using Interface 0 for outside and 1 for inside. We only have 1 Vlan in our environment. We have two three switches behind the firewall. Today the uplink to Interface 1, to the firewall, on the switch went bad. I want to setup a second inside interface on the firewall and configure it as failover incase this happens again. I want to attach it to the other switch. Can I do this? If so, what do I need to do? would it only be a passive/standby interface?
View 1 Replies
View Related
