I have a Cisco ASA 5505 with the base License. I want to split my network and add a new Internet Access, the first network in Orange works fine. My question is how can i access the file server from the second network (192.168.X.0 /24) ? The 3 switches are Cisco SF300-24P.
View 7 RepliesIve been readin all over the internet (including this site) trying to figure out if the asa can handle intervlan routing. Im not sure what I am missing on my config to get this to work. Ive read that it can work and Ive read that it cant work. How to get this to work on my asa 5505.
Here is my setup
Cable Modem ---> ASA (eth0/0)
(eth0/2) -->unmanaged switch for LAN connectivity
(eth0/3) --> Access point for wireless LAN connectivty
My config is attached
What I would like to do is be able to communicate between vlan3(LAN) and vlan4(Wireless LAN)
Whats strange is I can RDP between the two vlans but I cant ping or anything else.
We have two Cisco 5505 firewalls connecting to two ISP's . The two internal LAN's on the firewalls are 192.168.184.0/24 & 192.168.186.0/24. We also have a Cisco C3560x layer3 switch with vlan interfaces 184.3 & 186.3. We have two DGS-3100 Dlink layer 2 switches connecting our users to the Layer 3. Ip routing is enabled for intervlan communication & I can reach the Switch interfaces & firewall gateways from machines on both on the vlans.We have pbr enabled on the 3560 & users only on the .186 network can get to the internet. The switch is running the ipservices license & the sdm template is "desktop routing" .
Users on the .184 cannot access the internet but we can ping the layer3 interface & the firewall gateway. [code]
I have a question regarding CSS loadbalancer. Let's say there are 2 vlans in CSS:
1. Vlan 10: 10.1.1.0/24 as external interface, interface where most of the clients are coming from.
2. Vlan 20: 10.1.2.0/24 for real server vlan.
Virtual IP 10.1.1.10 is created in CSS on behalf of two real servers (10.1.2.11 & .12) in Vlan 20. Client from Vlan 10 can http access to 10.1.1.10 successfully.
In Vlan 20 there's also few clients which need to access servers via virtual IP. Vlan 20 Client PC (10.1.2.101) can ping 10.1.1.10, but can't access 10.1.1.10 http service.
Is there any way for CSS to forward service request coming from Server vlan to be send back to the same segment?
Just messing around with packet tracer for a little practice. I tried to setup a router on a stick config with 3 switches trunked and PCs on different vlans. Anybody know of any issues that may arise with STP and inter-vlan routing? I set everything up correctly with trunking, addressing, encapsulations, vlans, but did not touch STP. Unable to ping from any PC to any where.
View 19 Replies View RelatedI know very little about switches. This is the first time I've ever touched them. However, I'm the only one in the company who has the slightest knowledge on how to make them work.
4 vlans
vlan 1 - 192.168.32.1 - Existing network with Internet access
vlan 33 - 192.168.33.1
vlan 34 - 192.168.34.1
vlan 35 - 192.168.35.1
From the laptop on vlan 33 I can ping the management interfaces (192.168.x.1) for each of the vlans. However, I cannot ping anything on those networks.
Below is what I have with the config. Right now not much attached to these switches until they are setup.
Code:
config-file-header
poe-switch
[Code].....
Say I have a managed switch that supports VLANs. I have two computers and one server connected to the switch (I'll call them PC-1, PC-2, and SRV-1).Without routing, I want both PC-1 and PC-2 to talk to SRV-1 and vice versa, however I don't want PC-1 or PC-2 to talk to each other.I achieve this by making each port a trunk port. I make PC-1 a member of VLAN 2, PC-2 a member of VLAN 3, and SRV-1 a member of VLAN 4. The port that SRV-1 is on I make a tagged member of PC-1 and PC-2 (VLAN 2 and 3 respectively) and make the ports the PCs are on a member of the SRV-1 VLAN (VLAN 4).Everything tests OK (that is, the clients can't talk to each other, however the clients can individually talk to the server)
View 6 Replies View RelatedWhat is inter vlan routing protocol? What are its three modes?
View 6 Replies View Relatedi am doing a set-up having the ASA as my Layer 3 device providing inter-vlan communication. ASA with 8.3 firmware. how i can achieve this goal. i am trying to follow some answered topic related to this but its pre 8.3. VLANs created on the same physical have same security level.
View 2 Replies View Related[code] I would like to config two IP ranges, one for staff, one for guest wireless access. The dlink wap supports multi vlan SSIDs.Reason I'm doing this is to prevent access on the guest wireless to access the win 2003 server.Will the switch inter vlan route the 192.168.2.1 to 192.168.1.1? How will vlan 2 get DHCP, will dhcp relay need to be set on vlan 2 to 192.168.1.20 ? [code]
View 2 Replies View RelatedIn my home setup I have an PFsense firewall wich is doing all the routing right now, but right now my net speed is maxing out about 500mbit, i my think it's the pfsense hardware, but its an 1500Mhz C7 VIA with 2Gb ram, I just bought two new switchs, HP-1910-24g and a HP 5500-24G they can do some layer 3 routing, will my speed get a bumb up when the switch is doing some of the vlan routing.
View 2 Replies View RelatedCan inter VLAN routing be done on SRW (Cisco 300 series) switches ?
View 5 Replies View Relatedwe have a router with voip phones but no wifi, so i installed a separate wifi router but its ip is 192 range while the LAN is 10.1.1x range, how can i set it up so wirelessley connected PC's have access the file share and internet?
View 5 Replies View RelatedDoes Catalyst 3550 switch support inter vlan routing ?
View 12 Replies View RelatedI have a DC topology based on 2 layers, access and aggregation, based on 2 pairs of N5548Ps, both without L3 Daugher Cards. My intent is to use the aggregation N5K pair as L3 inter VLAN layer, so I configured all the VLAN default GWs there. The 2 layers are interconnected via vPC, in a double-sided vPC topology for some N2Ks and some vSwitches. The point is that, despite connecitivity is working fairly ok, for some applications, like file transfer via either FTP or HTTP, between hosts in different VLANs, the performance is too poor. The file transfer starts ok, but after a while it becomes lower and lower. ICMP is working, but I can see some strange random behaviour, like having some packets taking more that 20 ms (sometimes 40 or more), whilst average is 2 ms.
I read through some articles saying that until you don´t have the L3 license (the one coming with L3 Daughter Cards) you can expect some weird behaviour on L3 level. Is that true?. What can I do apart of purchasing L3 Daughter Cards?. Can I enable L3 Basic license at the moment (I don´t need dynamic routing for now).
Here some excerpts of what I´m saying:
PING results:
10000 packets transmitted, 10000 packets received, 0.00% packet loss
round-trip min/avg/max = 0.809/2.496/57.559 ms
System version: 5.0(3)N2(1)
License and features on the N5Ks:
switch# sho license usage
Feature Ins Lic Status Expiry Date Comments
Count
--------------------------------------------------------------------------------
FCOE_NPV_PKG No - Unused -
FM_SERVER_PKG No - Unused -
ENTERPRISE_PKG No - Unused -
[code]....
I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net.
My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20
I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2)my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to go out to the internet. I think it has to do with the routes. [code]
Can nexus 5010 supports inter v lan routing , as there is no core switch and router available in current network.
View 2 Replies View RelatedIn 3750 switch,I have configured intervlan routing.I have three vlans Vlan 10,vlan 20,Vlan 30 and I have assigned IP address for that Vlan.In vlan 10,I have connected one systen gigabitethernet 0/1 interface.From my system I am able to ping vlan 10 ip address but I can't able to ping other vlan ip address (vlan 20,vlan 30).Is it possible to up the protocol for all that time.
View 2 Replies View RelatedI recently set up a small photography business and am trying to get a Cisco 877 and Cisco SG300-10 switch to talk to each other.
What I want is for the Cisco 877 to handle the internet and the SG300-10 to handle the local network,
I have set up 2 vlans in trunk mode on the switch and want vlan2 to manage local traffic and vlan3 to handle the internet.
I have got the 877 connecting to the internet what I dont have, traffic going to vlan2 on the switch from the 877
Look at the running configs for the switch and the router and tell me how to get the vlan on the router to pass traffic to the switch. In a nutshell I am inserting the internet into the switch but am not sure how to progress. I have the c870-advipservicesk9 image file on the router.
Switch Config
interface gi2
description connection-to-data-vlan
exit
interface gi3
description connection-to-internet-vlan
exit
vlan database (code )
I am working for a large campus network. The network has more than 70 VLANS in a Layer 3 Switch(Catalyst 4503). Customer wants to stop intervlan routing between all vlans except 2 vlans. How will i do that? I have also a Firewall (ASA 5520) & a Router (2811) in up of the switch. Besides this, I have run HSRP in Layer 3 Switches for redundancy.how will i stop intervlan routing between VLANS except 2, with ACL or any other process has?
View 10 Replies View RelatedI'm looking to restrict Inter-VLAN routing through L3 switch (cisco 6500) and wanted to know best possible way to do it. I used VACL and achieved success to some extent, but my config is making clients take up to 5-6 mins to authenticate IP address from the DNS (bootps).My VACL config was as follows:
Subnet to restrict is 10.100.15.0 (VLAN 15)
STEP 1: Created extended ACL to allow bootpc/bootps through DNS
ip access-list extended EACL_DNS
permit udp any eq bootps any
permit udp any eq bootpc any
STEP 2: Created standard ACLs to allow only relevant subnet, server VLANs & some IPs from other subnets for printers/scanners etc.
ip access-list standard SACL_VLAN_15
permit 10.100.15.0 0.0.0.255 (the subnet I'm restricting)
permit 10.100.50.0 0.0.0.255 (server VLANs)
permit 10.100.25.45 0.0.0.0 (printer in another VLAN which has to have access in VLAN 15)
STEP 3: Created VLAN access list
vlan access-map VACL_15 10
match ip address EACL_DNS
action forward
vlan access-map VACL_15 20
match ip address SACL_15
action forward
STEP 4: Applying VLAN Access list on VLAN 15 vlan filter VACL_15 vlan-list 15 Though the above works, below is noted:
1. I'm still able to PING 10.100.15.2 (the switch virtual interface) from outside the subnet, which I don't intend to do so. Howeve all cients in the subnet have no connectivity from outside the VLAN 15.
2. As mentioned its taking quiet some time to negotiate with the DNS server at system boot time.
you find attached my network architecture with 2 Nexus 7010 on core layer and 2 Nexus 5020 on distribution layer, each one with 1 N2148T fabric extender switch. PC-A1 and PC-A2 are connected to one N2148T, PC-B1 is connected to the other N2148T. Nexus-7000-1 is HSRP Active for all VLANs, Nexus-7000-2 is HSRP standby. PC-A1 and PC-A2 are connected to VLAN A, PC-B1 is connected to VLAN B. PC-A1 and PC-A2 have the same default gateway correspondent to IP HSRP on VLAN A. It happens that PC-A1 is able to ping PC-B1 while PC-A2 is unable to ping PC-B1. If I issue a traceroute from PC-A2 I see Nexus-7000-2’s physical IP address as the first hop even if Nexus-7000-2 is HSRP standby. After the first hop the traceroute is lost. If I shutdown Port-channel 20 on Nexus-5000-2, PC-A2 starts to ping PC-B1.I can’t understand what’s wrong in this architecture.
View 6 Replies View RelatedI want to do the inter vlan routing packet tracer file url...configuration of MLS are as bellow can anyone tell me why vlan on switch0 can not ping vlan on switch1. [code]
View 12 Replies View RelatedI'm looking to setup Inter-VLan routing on a 4800G switch.
I'm looking for all workstations (VLAN1) to be able to talk to the windows network (VLAN2) and to our Novell network (VLAN3)
but I don't want Windows (VLAN2) and Novell (VLAN3) talking to each other. Is this possible accross a single switch? I have 7 switches available to use if needed.
I have a connection on IP 192.168.1.21, Subnet 255.255.255.0 - this is on the default VLAN1 on the switch. I need to route this to IP 10.0.3.101, Subnet 255.255.252.0 - which is set up on VLAN2 on the switch. I have set the switch to Layer 3 via console.
how I setup this route? I am use the Browser based interface.
I have set up a 2811 with seperate VLANs for phones, and another for computers/printers. Fa0/0 is trunked to a 3560 switch, which has all end devices plugged in. I have enabled the IP Routing commands on both devices, and from advice turned off proxy-arp on the VLANs on the router (unsure if this is causing the issue). The setup is as follows
Computer VLAN = 192.168.20.0
Phone VLAN = 192.168.50.0
Both on the same subnet, along with a router loopback address in the same subnet, at 192.168.10.1.I am having an issue understanding why, but if I try to ping a phone from a PC it times out. Or if I try to type the phone's IP into an internet browser to get the phone's GUI on screen, it fails. This should not be happening as IP routing has been enabled on both, and everything is in the same subnet, correct? PC's can ping other PC's and network printing works fine. Phones register and operate fine, but the two VLAN's will not interoute.Furthermore if I try and ping the router's loopback from the switch, it fails. But the trunk is up and operational because DHCP and devices work within their own VLAN. If I try to ping end devices from the switch, it returns 100%. There seems to be an issue with the router looping the different networks together.
I've recently installed an SGE2010 switch, which I have set to 'Layer 3' mode.
I have created 2 VLANs using 192.168.10.x and 192.168.20.x (using .50 for the VLAN IP address in each case) - however, I need to be able to allow certain traffic between the VLANs.Alternatively, to get things started - I'm assuming I need to set up ACLs to allow access between VLANs - how would I configure the switch to allow all traffic from one VLAN to the other?
We use Cisco Any connect with a Cisco ASA 5520 firewall. Today I changed the inside interface of the firewall's IP because i needed to do some inter vlan routing and needed to move the inside interface from the lan vlan to a routed port on our 3750.
Now people can vpn and authenticate to the MS radius inside but cannot access any network resources nor ping anything inside.
I have no router inplace that can do trunking (5505 basic license )I have 2 VLANS 10 Data 20 voice I have given both VALNs IPs lets say
-VLAN10 192.168.1.1
-VLAN20 192.168.2.1
Enabled IP routing and set the router as the gateway of last resort.Now becuase the L3 switchis doing the routing I have had to set the default gateway as the VLAN IPs. So PCs on VLAN10 get a gateway of 192.168.1.1 and phones on VLAN20 get a gateway of 192.168.2.1
Any real downside to having the 3560 doing the VLAN routing, is this the "correct "way to do things in the event I don't have a trunkable router?
configure my new SG300-28P. When I have started the switch, I have specified a new password and enabled telnet in order to setup the switch in Layer 3 mode.
After a restart, the switch took its IP address from a DHCP server. When I try to set a static IP address (192.168.2.1), I receive the following error message: Duplicated IP interface on the same subnet.
The IP address 192.168.2.1 is not used by any device within the network. For information, the message doesn't appear when the switch is in Layer 2 mode.
why I can't change the IP address of default vlan in Layer 3 mode ? All I can do is set the IP address to static or dynamic.
For test purpose, I have added 2 vlans. But I wasn't able to route traffic between vlan. how to configure the switch to route traffic between vlan?
find below details informations about my VLANs.
- Default (VLAN ID 1)
IP Address : 192.168.2.1
Subnet : 255.255.255.0
[Code].....
I have just bought myself a Cisco 2821 ISR.At present in my home I have a Cisco 2621XM. Fast Ethernet 0/0 is connected to a 3524XL as a trunk to provide my LAN with inter-vlan routing. it works great. Fast Ethernet 0/1 is connected to my ISP's cable modem and uses the command "Ip address dhcp" to get an IP and all other info from my ISP.FA 0/1 is Ip nat outside and the FA 0/0 and all sub interface like 0/0.1 .24 .168 etc all ip nat inside.I get intervlan routing and access to the internet via this router.I have this 2821 to replace the 2621XM as I plan to run CME on it and want gigabit routing on my vlans as at the moment on the 2621 routing between vlans it at half duplex or seems to be.I have configured the 2821 to ip nat outside on gig 0/0 and ip nat inside on gig 0/1 and all of the sub interfaces (same setup as my 2621 but with gig ethernet)I have no access to the internet at all but I can ping www.google.co.uk and other domain names from the terminal session when I am connected to the 2821 via the console or telnet/SSH. the gig 0/0 has an IP assigned from my ISP too but no other nodes on the network can ping outside.Am I missing something here? the version of IOS is V 15.
My access list goes someting like
access-list 1 permit 10.0.0.0 0.255.255.255
access-list 1 permit 192.168.1.0 0.0.0.255
access-list 100 permit ip 10.0.0.0 0.255.255.255 any
access-list 100 permit ip 192.168.1.0 0.0.0.255 any
and so on
I still cannot access the internet.....
I have a SG 300-28 switch with the latest firmware installed running in Layer 3 mode.
I configured this router with 4 VLAN's where VLAN 1 is connected to the network router. All VLAN's call all communitcate with one another. How do I go about configuring VLAN's so that they can only communicate with the router and the internet and not each other?
I have one cisco 3750G-48 switch, one cisco 3560G-PS switch, Cisco UC520, cisco 2851 and cisco wireless access point.i have setup up intervlan routing between the two cisco switches and the uc520 with a total of four VLANS, the problem i'm having is with the 2851 router, I have created a trunk between the 3750 switch and the 2851 router. should I create subinterfaces on the 2851 router for the four vlans by doing gigabieethernet 0/0.1, 0/0.100 and so on or should I create BVI subinterfaces.
reason I ask is I created four vlans on the vtp server switch which is the 3750 and I connected the uc520 to the 3750 switch via a trunk interface and set up vtp client on the uc520, after I setup p the vtp on the uc520 the vlans were automatically created on the uc520 with each vlan having its own BVI interface.
So I am not sure how to configure the 2851 router to interact with the four vlans. also the 2851 router have two hwic 1adsl wics installed which will have two adsl connections coming in.how to set up the 2851.