Cisco WAN :: VDSL Line Goes Down IOS 15.1 887VA
Jun 17, 2012
I'm facing an issue since 2 month now , no one is able to tell me what's going on. The line goes down suddently for 2 or 3 minutes and this happens everyday at the same range (~2 or 3 hours) of time . I don't have any scheduled task to cause this. ISP in his side has also made some tshoot but found nothing and is convinced that the problem is coming from our side :
Here is some log :
Cisco IOS Software, C880 Software (C880DATA-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
rtr-Id#show debugging
Generic IP:
IP packet errors debugging is on
IP NAT ERROR debugging is on
PPP:
[Code]...
View 3 Replies
ADVERTISEMENT
Nov 25, 2011
I'm trying to get an internet connection through my cisco 877va but I can't get access. I can see DSL up, however, the dialer0 interface can't get access to internet. Here is my configuration:
[code].....
View 2 Replies
View Related
Aug 24, 2012
Just got hold of my first 887va for my home, never configured a vdsl interface before and was just wondering if my setup looked good to someone whos done it a few times.
View 6 Replies
View Related
Sep 19, 2011
I'm trying to upgrade the VDSL firmware on a 887VA. I've uploaded the file vdsl.bin-A2pv6C035d_d23j to the router. I understand this file has to be renamed with a .bin extension in order to be recognized after a reboot, but the attempts I have made have not worked. What must this file be renamed to in order to load the new firmware into the VDSL controller?
Here is the current firmware information. I've tried several of the obvious file names.
Firmware Source File Name (version)-------- ------ -------------------VDSL embedded VDSL_LINUX_DEV_01212008 (1)
Modem FW Version: 110331_1212-4.02L.03.A2pv6C032b.d23fModem PHY Version: A2pv6C032b.d23f
View 1 Replies
View Related
Mar 13, 2013
Trying to get my 887va setup for VDSL but can't get to anything on the net -
Controller VDSL 0vpdn enablevpdn-group 1
interface ethernet0
no ip address
[Code].....
View 6 Replies
View Related
Apr 28, 2013
what enhancements, fixes, etc are included in the Cisco 887VA VDSL firmware version A2pv6C035l.d23j, relased 29-MAR-2013.I can't seem to find any release notes with this firmware.We are using version A2pv6C035d.d23j firmware on around 150 887VA's on BT ADSL lines, and was looking for any improvements this version may offer.
View 1 Replies
View Related
Dec 6, 2012
We have a remote site connected to ADSL line with a Cisco 887VA router attached. This has been working fine for the last couple of months. However, recently, the site have started to complain of performance issues (network slow, applications disconnecting, etc)Looking on the router, we can see evidence of packet loss/timeouts from a simple ping to the internet e.g. [code]
However, we have logged the fault with our service provider and they return all line tests as clear but what is particularly strange is that they also report “and the SNR Margins are well within threshold levels (Upstream 11.5 and Downstream 15.0)” which, unless I’m misunderstanding something, seems to be completely different from what the router itself is reporting.Is there a reason why the service provider’s stats for Noise Margin would appear to be so different from what the router is reporting?
View 2 Replies
View Related
Aug 30, 2012
difference of CISCO887VA-K9 and CISCO887VA-SEC-K9.I thought it because of the Advanced Security and Advanced IP Licenses, but it isn't, I've got the -SEC- Version now just with the Advanced Security license. So I asking myself why I bought the more expensive CISCO887VA-SEC-K9 if I have to buy the additional Advanced IP Services licenses extra..
View 14 Replies
View Related
Oct 10, 2012
Cisco 2500 series access servers show line usage with the "show line" command:
View 2 Replies
View Related
Feb 15, 2011
I have configured the "ISP" part of the VDSL as i am a tech for the ISP that has access to this, but i am not able to get my 887V to synch is there something i am doing wrong within the Cisco, i have included a debug and couple more things. [Code] ....
View 3 Replies
View Related
Aug 8, 2011
I will install in the next days a 886VA router (VDSL over ISDN using PPoE). Since I have no possibility to verify the VDSL config, this is what i prepared. Is this config OK (only VDSL part) ?
controller vdsl 0
operating mode auto
interface Ethernet0
[ code]...
For VDSL over ISDN the interface Ethernet0 must be used instead of ATM . Is this config correct ?
View 5 Replies
View Related
Nov 25, 2011
I have a dir 655 coupled with a 320b modem for adsl. Now I must switch to VDSL. Can I use the router with a VDSL Modem? Which modem could be used ? I do not see dlink products ..
View 14 Replies
View Related
Sep 3, 2012
I have installed a CISCO v887 router in Amsterdam officeI established a VPN tunnel between AMS office and Edinburg office.
1. The VPN is up and running
2. I am unable to browse anything from LAN computers in Amsterdam office.
3. From LAN computers I can traceroute to yahoo.com but from browser I cant browse yahoo.com and web page hanged out in this situation (website found waiting for reply). But nothing comes over and LAN users are unable to use internet.
[code]...
View 11 Replies
View Related
Mar 17, 2013
I want to dumb down a Cisco 886va to act as a pure vdsl bridge modem with a local ip to be able to do some admin work on the router. To some extent my config works, but i think the default vlan 1 kills my internet. When i connect the 88va the vlan bridge 7 and 8 goes up, the router behind connects via pppoe on vlan 7 but no traffic is going through. vlan 8 gets a dhcp lease for iptv and if i don´t switch the receiver on and off the traffic flows and the tv works. I am also able to connect to the local ip to access the web interface. [code]
View 1 Replies
View Related
Apr 7, 2011
I have a problem with my Cisco 887V VDSL-router. The router gets a ip-address with dhcp from my provider. That works fine. I also can ping from the router:
routerVdslTestNew#ping google.ch source vlan 1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 74.125.79.99, timeout is 2 seconds:
Packet sent with a source address of 10.10.10.1
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 48/48/52 ms
My problem: If I want to ping google from a computer in the VLAN1 the ping doesn't work.
C:UsersXXXXXX>ping 74.125.79.99
Ping wird ausgeführt für 74.125.79.99 mit 32 Bytes Daten:
Timeout.
View 3 Replies
View Related
Mar 26, 2012
I am trying to design a network for our block of 20 apartments. The WAN supplies Ultima at up to 40 mb/s and the takeup on LAN is anticipated to be modest. However I have been told that two residents operate non commercial web sites currently on stand alone adsl with ddns. The netgear router supplied by the ISP obviously has port forwarding but how do I differentiate for traffic on port 80?
View 1 Replies
View Related
Apr 25, 2013
I just bought a 5505 to learn from and am trying to attach my VDSL modem as a transparent bridge.It goes....
Laptop >>> (VLAN1) Cisco 5505 (VLAN2) >>> VDSL modem >>> internet
X.X.X.10 >>> (X.X.X.254) ------ (Y.Y.Y.254) >>> Y.Y.Y.10 >>> A.B.C.D.
I'm using the ASDM, if I configure VLAN2 with the IP address of the VDSL interface I can ping the modem from the console session via Putty. If I take that off and configure up the PPPOE client I can't ping the VDSL modem, I'd expect that. If I then add in an IP address to the PPPOE client config like I assigned to VLAN2 it doesn't ping either.If I can't ping the VDSL modem I don't expect it would work but it seems I can only either give it a static address which pings but has no pppoe or give it a PPPOE config which means I can't ping the VDSL. why I can't ping the VDSL modem when the interface is set as PPPOE with an IP address?Presumably if I'm on the ASA console doing pings from there to the modem then I'm ruling out problems with the routing from the laptop (trying to isolate where the issue is)
View 3 Replies
View Related
Oct 20, 2012
I recently upgraded my DSL service, which required installing a new VDSL modem/wireless router (Actiontec c1000a.) Before the upgrade, I was using an older standalone DSL modem with a Netgear router to provide wireless access to my gaming consoles, laptop, etc. Everything works as before with my new wireless router EXCEPT my son's laptop. All my consoles, iPods, and desktop CAN connect to the wireless network, and the laptop will connect over a WIRED ethernet connection. I cannot get it to connect to the wifi.
[code]....
View 6 Replies
View Related
Nov 10, 2012
I desperately try to set up the X3000 as a router behind a vDSL modem. When I choose connection through Ethernet and then PPPoE, it never keep the credentials after reboot in spite of having saved the data before.
View 6 Replies
View Related
May 2, 2011
I have been using a Linksys Wireless-G ADSL WAG200G, Annex-A Gateway Router and it has been fine, now my ISP have told me that they are modernising the network and will need a router capable of managing ADSL2/ VDSL connections, so will my router be able to do that or will I have to buy a new one? It has firmware 1.01.09?Edit: I see in the DSL Modulation menu which is set at present to "Multimode" I also have options to select ADSL2, ADSL2+, ADSL2 AnnexM, ADSL2+ AnnexM and ASDL2 AnnexL but I do not see any mention of "VDSL"
View 2 Replies
View Related
Jan 24, 2013
I have a Dell Aspire 5332 laptop and i haven't used it since November 2012 (where it was working fine).It had Windows updates when i switched it off. I switched it on today and i have no internet connection. When hovering over the icon it says unidentified network - no internet access. My service provider is British Telecom and i am on the Fibre Optic package. I am using the BT Home Hub 2.0.Fibre Type B and also a Echolife HG 612 model FTCC VDSL NTE Router. I have Norton installed on the machine but there is only 1 day left on the subscription. I have tried a wired connection from the router but still have the same message. 2 other computers are wired to the router and all of our Ipads and Macbook connect wirelessly with no problems.
View 19 Replies
View Related
Mar 27, 2012
The reason is i want to know the difference between the leased line and the DSL line. The whole thing behind the confusion is, We plan to have a high speed internet connection in our office. We will don't have a branch office or some thing like that. I preffered to have high speed internet in our office. I found in some website that Lease line will have high speed connectivity(Upto 10Gbps). Can i use the lease line or DSL is enough for our office. Our office contains of 82 user who will use internet.
View 2 Replies
View Related
Mar 3, 2012
Have they changed the poe requirements for this router? This model seems to be a seconed gen 887 with internal wireless, fanless and instead of there being a second 2 pin power socket for the poe option there is just 1 power input with the text under is saying. 'poe option requires 5a power adapter' I have purchased the 800-IL-PM=2 to delivery poe on the first 2 ports from this document [URL]While the daughter board does fit in the stand off pegs are too short and the power adapter is incompatable.
View 9 Replies
View Related
Mar 25, 2013
Is there a GUI that can be used to setup the 887 router. I need to setup a VPN.
View 1 Replies
View Related
Apr 1, 2011
I'm trying to get an internet connection through my cisco 877va but I can't get access. I cant apply show cotroller vdsl 0 command and I can see DSL up, however, the dialer0 interface can't get access to internet. If I apply "show int dialer0 account" coomand, I get the next message: "No traffic sent or received on this interface". [code]
View 14 Replies
View Related
Feb 13, 2013
Firstly does the 887VA have a WAN port? I know it does VDSLIf this model is doesn't have both these options do you know which model does?
View 1 Replies
View Related
Jan 9, 2013
I need to configure a Cisco 887va router for a customer with a firewall that doesn't support PPPoA. I basically need to ensure all traffic that is recieved from the internet (ADSL connection) is NAT'd to a LAN interface so the firewall can do the specific NATing. I have the following route map and NAT rule in mind, but what I am confused about is that if the atm0 interface needs to be configured as the outside interface and vlan2 as the inside interface. How will the following work?
View 0 Replies
View Related
Apr 23, 2013
I have a problem and I dont know much on Cisco Products
The router is Cisco 887 VA
When it starts the Leds Ok AND Fe lan are blinkng then are always on .After 10 seconds lan led is off a and pc shows cable is unplugged
I tried all ports and same thing happened .I tried with different ethernet cord but the problem persists
I installed Cisco Configuration Professional and it hangs on Retrieving Port
View 2 Replies
View Related
Feb 1, 2012
Actually I have to make a VPN between an 5520 ASA and a Cisco 887VA-K9 Router. Connected to ASA I have the outside interface, the inside-DMZ interface, the PCs interface and the VoIP interface. In the other site I will need to have a new subnet and a VoIP phone which I need to connect to the VoIP subnet in the other side in order to work with our CCM servers.I need two VPN established between ASA and 887 Router?
View 15 Replies
View Related
May 9, 2013
I have an 887VA-K9 which boots into ROMMON mode every time. It seems to have 3 tries at booting, then fails.
The entire console output from power-on is (blank lines removed):
System Bootstrap, Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 2009 by cisco Systems, Inc.
[Code].....
View 3 Replies
View Related
Apr 14, 2011
what web-based programs do i need to install a 887VA? I tried Cisco CP express version 2.1, not a supported device.
View 2 Replies
View Related
May 13, 2013
I have set up my network to pass ethernet (layer 2) traffic accross an adsl connection to another 887va router. this link is set up as a L2TP. I have a PC at one end of the tunnel and a web ranger that operates at layer 2 level. I can see the layer 2 traffic entering the router from the PC however it does not seem to go over the L2 tunnel to the other router.
I also need to know what debug codes I can enter to see if the data is being filtered and if so why?the debug L2TP gives the following output:
L2TP Tunnel and Session Information Total tunnels 1 sessions 1
LocTunID RemTunID Remote Name State Remote Address Sessn L2TP Class/
Count VPDN Group
[code]....
View 1 Replies
View Related
Jan 26, 2012
I've got a brand new C887VA-W-E-K9 that is up and running on a BT VDSL connection. That side of it is fine... But the integrated AP module on it keeps reloading.. I can be on the AP console reading the config via 'sh run' and suddenly it'll be loading the OS again... There's no errors logged, no errors on the console or anything... (I also have yet to get the radio working, it starte dbefore I'd finished the config).
It doesn't seem to be anything I'm doing as if I just leave the console, it'll just sit there... reloading every few minutes... (Although sometimes it seems to stay up for longer).
The console just looks like this. WHich is taken from listing the running config and while sitting at the --more-- prompt... Bang...
interface GigabitEthernet0
description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router
no ip address
[Code].....
View 6 Replies
View Related
