what enhancements, fixes, etc are included in the Cisco 887VA VDSL firmware version A2pv6C035l.d23j, relased 29-MAR-2013.I can't seem to find any release notes with this firmware.We are using version A2pv6C035d.d23j firmware on around 150 887VA's on BT ADSL lines, and was looking for any improvements this version may offer.
View 1 RepliesI'm trying to upgrade the VDSL firmware on a 887VA. I've uploaded the file vdsl.bin-A2pv6C035d_d23j to the router. I understand this file has to be renamed with a .bin extension in order to be recognized after a reboot, but the attempts I have made have not worked. What must this file be renamed to in order to load the new firmware into the VDSL controller?
Here is the current firmware information. I've tried several of the obvious file names.
Firmware Source File Name (version)-------- ------ -------------------VDSL embedded VDSL_LINUX_DEV_01212008 (1)
Modem FW Version: 110331_1212-4.02L.03.A2pv6C032b.d23fModem PHY Version: A2pv6C032b.d23f
I'm trying to get an internet connection through my cisco 877va but I can't get access. I can see DSL up, however, the dialer0 interface can't get access to internet. Here is my configuration:
[code].....
I'm facing an issue since 2 month now , no one is able to tell me what's going on. The line goes down suddently for 2 or 3 minutes and this happens everyday at the same range (~2 or 3 hours) of time . I don't have any scheduled task to cause this. ISP in his side has also made some tshoot but found nothing and is convinced that the problem is coming from our side :
Here is some log :
Cisco IOS Software, C880 Software (C880DATA-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
rtr-Id#show debugging
Generic IP:
IP packet errors debugging is on
IP NAT ERROR debugging is on
PPP:
[Code]...
Just got hold of my first 887va for my home, never configured a vdsl interface before and was just wondering if my setup looked good to someone whos done it a few times.
View 6 Replies View RelatedTrying to get my 887va setup for VDSL but can't get to anything on the net -
Controller VDSL 0vpdn enablevpdn-group 1
interface ethernet0
no ip address
[Code].....
difference of CISCO887VA-K9 and CISCO887VA-SEC-K9.I thought it because of the Advanced Security and Advanced IP Licenses, but it isn't, I've got the -SEC- Version now just with the Advanced Security license. So I asking myself why I bought the more expensive CISCO887VA-SEC-K9 if I have to buy the additional Advanced IP Services licenses extra..
View 14 Replies View RelatedWriting this hoping to see how DLink intends to respond to this very large hole. As someone who works in security this is 2 week old news to me but is probably new to everyone else "Hopefully not dlink devs".
So the DIR 825 along with millions of other routers are vulnerable to an outside upnp exploit basically means somebody from outside can root your router and for example open up whatever ports they want. Upnp has its own issues but it useful for those who don't want to open up a port every time some app might need a specific port but was never meant to be accessible from outside your network, Until now.
This is not some bizarre proof of concept or something that is even hard to pull off and what it would give is access to your entire private network and everything that might entail. You can test if your router is vulnerable at this link. It's owned by Steve Gibson. Many of you probably know of him, Somewhat of a celebrity in the security world. There is a upnp exposure test you can do right off the main page. It also explains whats happening and even shows you the code being used, Quite fascinating actually.
what is the latest firmware version for d-link dir-825? It tell me that i currently got the 2.60VT, is it the last one? If no, where can i download and how the latest version?
View 14 Replies View RelatedMy firmware version 2.00NA (shipping version) is still working well.
When I selected 'Check online for any latest firmware' using the existing firmware, I got a message that that v2.07 (dated 2012-2-21) is available. Until now the router's check has always reported that I have the latest version.
I need to find out from other persons whether or not v2.07 is a real upgrade or is it full of bugs. I tried it once a long time ago and Shareport didn't work at all. Immediately I re-installed v2.00 and I've been pleased with the original shipping version.
What's the scoop on v2.07?
Recently he was having connection issues so decided to upgrade firmware and for some reason he did it through the management console (clicked the update to have it download the new file automatically and instantly upgrade instead of doing it manually himself). Told him not to do that anymore. Anyway, it wiped the existing firmware obviously and did not update to the newest. I came over to find it wouldn't connect at all. I was able to get into the reset console (hold reset while powering on, manual set IP on computer to 192.168.0.2 and gateway to 192.168.0.1 an then pointed the browser to 192.168.0.1).This window shows the current firmware as version 1.0.0.1 dated in 2007.I had downloaded the version 3.0 firmware and the most recent version 3.13 and had them on a flash drive, dropped them on the hard drive and attempted to flash first the newest and then the 3. Neither one would take and the router remains down. The page itself never changed after hitting SEND to upload the firmware, the browser displayed a progress bar for "uploading" and hit 100% then just sat saying "waiting for response from 192.168.0.1" until the browser timed out after several minutes.
View 4 Replies View RelatedI just bought RV042G with serial number NKS16120688 to replace old RV042 which is cannot upgrade to new version firmware(from above V.4).After I connect to my TOT isp modem to new rv042g, the router distributes ip (DHCP), get dns from isp normally but it cannot connect the internet at all.It seems this new firmware is not compatible with tot isp in Thailand while old rv042 with old firmware can run smoothly.I have to try many things such as change wan port, change modem and also buy another new RV016, but results still the same.
View 1 Replies View RelatedI have an old RV082 with firmware version 2.0.0.19. I want to replace it with a new RV082 firmware version 4.0.2.08.I exported the fv2 config but can't restore it on the fv4. I get "invalid file type" error. The fv4 box is looking for a .config file and the fv2 box saves as a .exp file.
View 4 Replies View RelatedASDM access to 5500 using Java was just a frustrating experience. If you manage only one device you may not notice the pain. But if you are managing multiple devices with some device 'forbidden' to update ASA firmware,
I spend few days looking at the issue and came to a conclusion and decided to post to guide all newer VPN admins who will go through the same pain and hopefully we can reduce some combined wasted time.
Recommended Beginning Setup for New Admin :
[code]...
I have 2 WAP4400N access points, each has a different version of the firmware installed and one has options that the other one does not.I have one access point running
If I visit the Cisco site for firmware updates, I see that only one version of firmware is available for this access point... 1.2.14.I realize that Linksys is not Cisco's main area of business, but if you are going to provide downloads for access points you could at least make sure that you have the latest version available.
Where the list of changes for the latest firmware version can be found? My new DIR-655 has firmware from May 2010, and I see the latest and greatest on the DLINK website is from September. But it doesn't state what the changes are, so I'm not sure if I should upgrade or not.
View 8 Replies View RelatedI happened to update firmware version of my WAG54G2 to the latest version 1.xx.xx.19. Since then connection to internet has became erratic. If rebooted, the device mostly doesn't connect. Switching to PPPoE from PPPoA and vice versa works but i have to do it every time the device is rebooted. Sometimes even that doesn't work. Basically it acts random. DSL connection shows as connected, but the internet interface is mostly down. I was wondering if i can switch back to to old 1.xx.xx.10 version. It never gave me any trouble ever for around 2 years.
View 4 Replies View RelatedI just recently updated my firmware on my linksys router WRT54G with the new version of linksys firm ware and now my router does not work. I can not access the GUI under the ip address 192.168.1.1. I 've tried to reboot the router using the 30/30 method that is suggested by Linksys, but I still can not access the routers GUI.
View 2 Replies View RelatedI would upgrade the firmware before deciding to replace router with a new one. I noticed there have been several updates to the firmware since I originally installed the router with the current available firmware version of 1.35NA.
View 12 Replies View RelatedI need to reflash a WRT54G version 2, but on the support page I can not find any firmware. Only for version 2.2. is it the compatible also with version 2?
View 2 Replies View RelatedJust purchased a Belkin AC1200 Router Modem and unable to locate the model number what is the current firmware version It is the UK model and I guess it must be very new?
View 4 Replies View RelatedI made the change WAG120G (GREAT) for WAG120N (**bleep**) and I confess that I was somewhat disappointed, the quality of the company fell dramatically. Unlike its predecessor this modem / router is bad in many ways and first of them is support for Macintosh products, the connection drops constantly and have to get on and off the wifi to work. The modem restarts and constantly drops the connection status and its predecessor NEVER did that. iPad, iPhone and Macbook can not even keep me surfing for more than one hour, the connection just stops working. Even the cable connection, my Xbox sometimes worth it to maintain a stable connection in Live. The modem has been updated with the latest firmware version (1.0.0.16). Another thing I noticed is that the modem takes A LOT to connect with the operator. It's bad, it's expensive and does not work! I
View 9 Replies View RelatedLooking into a firmware upgrade. I have a WRT160N. The label on the back, next to Model Number, simply says WRT160N with no version number. I therefore conclude, per info on the Cisco site, that it is a V1 model, not V2 or V3. And yet the Admin web page for the router says firmware version is 3.0.02. I'm pretty confident I have never upgraded firmware on this router, which means this is how it came out of the box long ago. Latest firmware for V1 is 1.02.11; latest firmware for V3 is 3.0.03.
Should I upgrade to 3.0.03? Is there a way to downgrade to 1.02.11? I'm having some minor issues whch may or may not be the ruter's fault, I figure a firmware upgrade (downgrade?) will at least rule out router firmware issues.
Is there any firmware update for this product? I'm not hable to find it... Product: WRT54GC Version 2.0 (wwith external anthena)
View 9 Replies View RelatedI have a DIR-655 Version B running the stock 2.0 firmware and a Motorola SB6120 cable modem and my ISP is comcast. I have had comcast come out and test my line and everything is fine. I have a desktop directly wired to the internet and several portable devices accessing the router.I cannot connect to the internet. My network is available and none of my devices ever indicate the network isn't available. When I try to load a website it just says "waiting for reply..." and nothing happens. The solution that always works is rebooting both the modem and the router. What is odd is that this problem comes and goes, I will go a week with zero issues, then I go all week with rebooting my stuff 5-8 times a day..What have I tried? I tried the settings that are recommended by Furrynuts to users complaining. I have also tried changing the wireless band settings to different channels as well.
View 6 Replies View RelatedModel : TD-W8961ND
Hardware Version : V2
Firmware Version : 120703
ISP : [/COLOR]
Region : United Kingdom
Model : TD-W8961ND
Hardware Version : V2
Firmware Version : 120703
ISP : Plusnet
I bought this recently on EBay and it works fine. I have just checked the firmware version and it displays as 120703 rel 29722. This version doesn't appear amongst the downloads - the most recent is 120427. Has somebody upgraded to the wrong software? Should I upgrade to 120427?
Region : United-States
Model : TL-WR702N
Hardware Version : V1
Firmware Version :
my Firmware Version is chinese i can't understand it.i go to tp-link.com go to support the last version is older with compare are old.
A router newbie here. Running XP Pro with Comcast Cable. Want to install a BEFSR41 V2.1 as firewall, and add a second PC later.
Q. Which firmware version is the most up to date?
Q. How do I install the firmware?
Q. Will I need to manually enter any Comcast information?
Q. Is there a step by step installation tutorial?
I have what I believe is an original (V1) version of the BEFSR41 gateway/router. The label underneath the device only shows the model number with no version information. Current firmware version on the device is 1.46.02, dated Aug 03 2004.
Can I confirm (1) that I indeed this router is at hardware version 1? If that is the case it appears from your web site that version 1.46.02 is in fact the current and only firmware version for the device and that there are no firmware version upgrades available.
The DHCP software current does not have IP address reservation, which I am interested in adding if possible via firmware upgrade. If not then I have to consider whether I want this feature bad enough to replace the router.
Where do I find the firmware upgrade for version one (1) of my F5D9230-4 Wireless G Plus Mimo router?
Only versions two (2) through five (5) are listed on the F5D9230-4 firmware page: [URL]
It appears that there is no firmware I can download for my WRT54GL Version 1.1. While it may never have been updated from what the router came with from the factory, it would still be useful to have it available. In my case, I would like to revert the router from the DD-WRT firmware to factory specs.
View 3 Replies View RelatedI tried to download the new firmware version (2.0.04) for Linksys x2000 hw version 1 Annex A: error 404 page not found.Same issue with 2 different machines on different internet connections.
View 3 Replies View RelatedI am needing to update the firmware for my router. befw1154 version 4. I went to the download section of the linksys website, and it does show that there is an update there, but I have read in alot of places that the update downloads are in a zip file. WEll it definately wasnt in a zip file, and all it did was download a strange file and there was nothing to install or anything. My router is still on the blitz, and going down every few minutes and I am having to restart just to have it go down again. firmware update for this router?
View 1 Replies View Related