Just got hold of my first 887va for my home, never configured a vdsl interface before and was just wondering if my setup looked good to someone whos done it a few times.
View 6 RepliesI'm trying to get an internet connection through my cisco 877va but I can't get access. I can see DSL up, however, the dialer0 interface can't get access to internet. Here is my configuration:
[code].....
I'm facing an issue since 2 month now , no one is able to tell me what's going on. The line goes down suddently for 2 or 3 minutes and this happens everyday at the same range (~2 or 3 hours) of time . I don't have any scheduled task to cause this. ISP in his side has also made some tshoot but found nothing and is convinced that the problem is coming from our side :
Here is some log :
Cisco IOS Software, C880 Software (C880DATA-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
rtr-Id#show debugging
Generic IP:
IP packet errors debugging is on
IP NAT ERROR debugging is on
PPP:
[Code]...
I'm trying to upgrade the VDSL firmware on a 887VA. I've uploaded the file vdsl.bin-A2pv6C035d_d23j to the router. I understand this file has to be renamed with a .bin extension in order to be recognized after a reboot, but the attempts I have made have not worked. What must this file be renamed to in order to load the new firmware into the VDSL controller?
Here is the current firmware information. I've tried several of the obvious file names.
Firmware Source File Name (version)-------- ------ -------------------VDSL embedded VDSL_LINUX_DEV_01212008 (1)
Modem FW Version: 110331_1212-4.02L.03.A2pv6C032b.d23fModem PHY Version: A2pv6C032b.d23f
Trying to get my 887va setup for VDSL but can't get to anything on the net -
Controller VDSL 0vpdn enablevpdn-group 1
interface ethernet0
no ip address
[Code].....
what enhancements, fixes, etc are included in the Cisco 887VA VDSL firmware version A2pv6C035l.d23j, relased 29-MAR-2013.I can't seem to find any release notes with this firmware.We are using version A2pv6C035d.d23j firmware on around 150 887VA's on BT ADSL lines, and was looking for any improvements this version may offer.
View 1 Replies View RelatedI have installed a CISCO v887 router in Amsterdam officeI established a VPN tunnel between AMS office and Edinburg office.
1. The VPN is up and running
2. I am unable to browse anything from LAN computers in Amsterdam office.
3. From LAN computers I can traceroute to yahoo.com but from browser I cant browse yahoo.com and web page hanged out in this situation (website found waiting for reply). But nothing comes over and LAN users are unable to use internet.
[code]...
I have cisco router 887VA.Question is when i connect that WAN port ( eth0) with any switch or laptop/pc i do not see the port in up state. What can be the reason.I have done "no shutdown " on interface level and there is no configuration on interface except the IP address , but it show " up down "state even the port is connected to some device. ( Is the port is faulty or some other reason).As per my concept it should show up state when we connect to some device ( Like router / switch / laptop).
View 6 Replies View RelatedI wish to assign a MAC ACL to a layer 2 interface on an 887VA router but cannot seem to see how to do this.
View 2 Replies View RelatedI'm trying to configure an 887VA for a pppoe ADSL2+ connection with no luck.I know the ISP requires pppoe (LLC), and the pvc is 8/35.
The CD light is on, and the line is up, but the 887 just won't connect
I have been trying to connect a new Cisco 887VA Router to the Internet using ADSL via PPPoE and have been unsuccessful. The DSL line is active and functioning correctly since the current "old" router is connected and working without any problems (the "old" DLink router is connected to an Alcatel DSL Modem). AT&T provides the ADSL service to the office. When the Cisco Router is connected it tries to negotiate a connection via PPPoE on the WAN interface but utlimately fails. The IP for the WAN interface is dynamic.
Below is the current configuration of the router.
!
! Last configuration change at 00:43:54 UTC Sun Jun 26 2011
!
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
[code]....
difference of CISCO887VA-K9 and CISCO887VA-SEC-K9.I thought it because of the Advanced Security and Advanced IP Licenses, but it isn't, I've got the -SEC- Version now just with the Advanced Security license. So I asking myself why I bought the more expensive CISCO887VA-SEC-K9 if I have to buy the additional Advanced IP Services licenses extra..
View 14 Replies View RelatedI have configured the "ISP" part of the VDSL as i am a tech for the ISP that has access to this, but i am not able to get my 887V to synch is there something i am doing wrong within the Cisco, i have included a debug and couple more things. [Code] ....
View 3 Replies View RelatedI currently have an ASA5510 with 2 interfaces (outside and Inside) running remote VPN for clients and L2L VPN for a couple of sites. I have traffic entering the inside interface, matching interesting traffic, being wrapped up in IKE / IPSEC and sent out via the outside interface. All straightforward so far.Now I have a new VPN which is required to go over another interface and not the outside. The traffic comes in to the inside interface as normal and should be matched via ACL, encrypted and sent out th e new interface however the traffic is simply sent out of the outside interface and doesn't get any IKE headers. If I reconfigure the interface to be be the outside it does at least match the ACL, wrap it up nicely in IKE and try to get to get to the remote peer.My questions are why does this behaviour occur and why isnt the traffic marked interesting and sent out the new interface.I don't have any issues creating a new VPN if I want it to go external, I just add the required information to the outside_map but i need the traffic to be encrypted and sent over another interface. I not a huge fan of the GUI for this but I've tried both CLI and GUI with the same results.
View 2 Replies View RelatedWith most of my Layer2/Layer3 switches, I'm accustom to giving them a SVI on my management VLAN, and calling it a day. I can't find in the Cisco Nexus guides how to do something similar; everything points to the mgmt0 physical interface, which seems like I need to uplink it to an access port on another switch. Can somebody point me in the right direction for how to do give the Nexus an IP that I can ssh/snmp into it across a trunk for management? I must just be missing the keyword.. NX-OS is still quite a different beast.I see in the manual it says: "SSH has the following prerequisites: You have configured IP on a Layer 3 interface, out-of-band on the mgmt 0 interface or inband on an Ethernet interface." Cisco Nexus 5000 Series Switch CLI Software Configuration Guide page 284, How do I configure an IP on a Layer 3 interface on a Nexus?
View 16 Replies View RelatedActually I am new to this ASR , in my environment my 6513 is connected ASR , I want to know how can we access and configure VLAN on Gigabit interface which is connected to 6513.
View 9 Replies View RelatedOn the ATM0 interface on a 877 do you have to configure the bandwidth or will the router automatically negotiate this ? Also is the bandwidth command in relation to the upstream or downstream bandwidth?. We currently specify bandwidth 448 which matches the upstream.
View 3 Replies View RelatedI will install in the next days a 886VA router (VDSL over ISDN using PPoE). Since I have no possibility to verify the VDSL config, this is what i prepared. Is this config OK (only VDSL part) ?
controller vdsl 0
operating mode auto
interface Ethernet0
[ code]...
For VDSL over ISDN the interface Ethernet0 must be used instead of ATM . Is this config correct ?
I have a dir 655 coupled with a 320b modem for adsl. Now I must switch to VDSL. Can I use the router with a VDSL Modem? Which modem could be used ? I do not see dlink products ..
View 14 Replies View RelatedAfter reading a bit about interVLAN routing got a doubt regarding how trunking takes place at router and at switch.In case of switch we configure a port interface as trunk port and say all vlan's are allowed here but in case of router we configure sub interface as trunk saying particular vlan belongs to particular subinterface .Can't we configure only a single port interface on router just like Switch and say all vlan's are allowed here on this interface ,why to go for sub interfaces?
View 2 Replies View RelatedI had insatalled the ACS 5.2 on Vmware . As per my requirement i need to configure a user to restricted privilege so that he should be able to execute only the below commands on the switch .
-Show ver
-Show interfaces
-Show ip Interface Brief
-Configure terminal
-Interface <interface name >
-Shutdown
-No shutdown
The users should not be authorized to execute any other commands than above listed one .After the configuration i was not able to restrict the config mode commands . Once the user is authoized for Configure terminal access he will have full access on the device. How to configure the command set only to allow interface access and he should be able to apply Shutdown and No shutdown command .
Is it possible to configure more than one layer 3 interface for netflow on a 3845? I can't seem to do it. Is there something I am missing?
View 2 Replies View Relatedhow do we configure sub interface for nexus 7k?do we have to issue ma-address command under physical interface and than configure subinterface? if yes than what do we have to type the mac address for "mac-address" command?I can doing and than configure subinterface but the interface/subinterface didn't come up. do we have to bounce it couple times to bringe it up?
View 1 Replies View RelatedI have a Cisco 5512 x Firewall connected with Cisco Layer 3 switch 3750.I have two different WAN connections, one for Data and one for voice. Cisco Layer 3 switch is configured with 2 different VLAN's one for data & other is Voice Vlan. Switch is providing DHCP to computers and IP phones. Voice Pool 192.168.10.0/24 Vlan10 and Data pool 192.168.20.0/24 Vlan20.I need to route my data & voice traffic separately. Cisco ASA is connected with two different ISP's. So, how can I do this configuration so that Voice and Data traffic will route separately.
View 7 Replies View RelatedI want to configure a MAC address on my asa 5520 interface.I ask you if exist a private MAC address range?
View 5 Replies View RelatedI was trying to config qos on 3550 interface
Match protocol is not supported for this interface
So does this mean that qos is not supported on 3550?
I have a Cisco 1142N configured in autonomous mode.I'm running on:Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 15.2(2)JA, RELEASE SO FTWARE (fc1)
I can loggon to the web interface but it won't show me th expected status information.
I would like to configure the 881G to use both the cellular interface and Fe4 WAN port for internet connectivity.Interface Fe4 is connected to an ADSL router.
I have configure each interface with a default route and weighting:
ip route 0.0.0.0 0.0.0.0 Dialer0 200
ip route 0.0.0.0 0.0.0.0 FastEthernet 4 100
I need to configure Fe4 to get an address as a DHCP client:
interface FastEthernet4
ip address dhcp
no shut
duplex auto
speed auto
How do I remove Fe4 from VLAN1? There is some existing config around VLAN 1:
interface Vlan1
ip address 10.73.0.1 255.255.255.0
ip helper-address 192.168.140.13
ip tcp adjust-mss 1400
no autostate
ip sla 100
icmp-echo 10.64.4.15 source-interface Vlan1
tag 3G Keepalive
frequency 10
Then I guess I need to adjust my Internet-IN ACL to allow broadcasts and UDP 67 and 68?
I want to dumb down a Cisco 886va to act as a pure vdsl bridge modem with a local ip to be able to do some admin work on the router. To some extent my config works, but i think the default vlan 1 kills my internet. When i connect the 88va the vlan bridge 7 and 8 goes up, the router behind connects via pppoe on vlan 7 but no traffic is going through. vlan 8 gets a dhcp lease for iptv and if i don´t switch the receiver on and off the traffic flows and the tv works. I am also able to connect to the local ip to access the web interface. [code]
View 1 Replies View RelatedI have a problem with my Cisco 887V VDSL-router. The router gets a ip-address with dhcp from my provider. That works fine. I also can ping from the router:
routerVdslTestNew#ping google.ch source vlan 1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 74.125.79.99, timeout is 2 seconds:
Packet sent with a source address of 10.10.10.1
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 48/48/52 ms
My problem: If I want to ping google from a computer in the VLAN1 the ping doesn't work.
C:UsersXXXXXX>ping 74.125.79.99
Ping wird ausgeführt für 74.125.79.99 mit 32 Bytes Daten:
Timeout.
I am trying to design a network for our block of 20 apartments. The WAN supplies Ultima at up to 40 mb/s and the takeup on LAN is anticipated to be modest. However I have been told that two residents operate non commercial web sites currently on stand alone adsl with ddns. The netgear router supplied by the ISP obviously has port forwarding but how do I differentiate for traffic on port 80?
View 1 Replies View RelatedI am trying to configure EIGRP on my ASA DMZ Interface - topology as follows: [code] The ASA is currently configured for EIGRP with the inside 3560x switch and passing routing updates properly.However, the ASA will not send/receive routing updates to/from the DMZ 3560x switch - the two devices do establish eigrp neighbor relationship. [code]
View 4 Replies View RelatedI have two 3750 switch.switch A(main) and switch B is connected by OFC but i have another wireless link for backup.Now if OFC goes down then i manually connect wireless link with switch B for this reasons i am faceing a lot of problem. I want without any changing of cable if my primary link goes down then my backup link automaticaly goes up and vice versa .
Switch-A port gi1/0/9 and Switch-B port gi1/0/9 is connect by OFC Switch-A port gi1/0/8 and Switch-B port gi1/0/8 is connect by Wireless link (backup) i attach my network diagram kindly find the attachment file.