Cisco WAN :: Configure More Than One Layer 3 Interface For Netflow On 3845?
Mar 20, 2013Is it possible to configure more than one layer 3 interface for netflow on a 3845? I can't seem to do it. Is there something I am missing?
View 2 Replies
ADVERTISEMENT
Cisco :: How To Configure IP On Layer 3 Interface On Nexus
Apr 11, 2011With most of my Layer2/Layer3 switches, I'm accustom to giving them a SVI on my management VLAN, and calling it a day. I can't find in the Cisco Nexus guides how to do something similar; everything points to the mgmt0 physical interface, which seems like I need to uplink it to an access port on another switch. Can somebody point me in the right direction for how to do give the Nexus an IP that I can ssh/snmp into it across a trunk for management? I must just be missing the keyword.. NX-OS is still quite a different beast.I see in the manual it says: "SSH has the following prerequisites: You have configured IP on a Layer 3 interface, out-of-band on the mgmt 0 interface or inband on an Ethernet interface." Cisco Nexus 5000 Series Switch CLI Software Configuration Guide page 284, How do I configure an IP on a Layer 3 interface on a Nexus?
View 16 Replies View RelatedCisco WAN :: How To Configure Vlan Tag On Routed Layer 3 Interface In 3945 Device
Jun 10, 2012how to configure vlan tag on routed layer 3 interface in cisco 3945 device?
View 2 Replies View RelatedCisco Switching/Routing :: Configuring Netflow For Layer 2 Switched Traffic On Cat6509
Jul 10, 2012I want to configure layer 2 switched netflow on my cat 6509 running vss,
I have configured the 2 commands below
ip flow ingress layer2-switched vlan 1,2,3
ip flow export layer2-switched vlan 1,2,3
However, if I look in the config the export bit isnt there after?
It is running a PFC
VS-F6K-PFC3C
Should layer 2 switched netflow work in this chassis ? it says on the Cisco site that it works on the below
"The command is supported on Supervisor Engine 720 in PFC3B and PFC3BXL mode only and on Supervisor Engine 2 with a PFC2"
Cisco WAN :: Configure Netflow On 877 Router?
Dec 13, 2010how I configure netflow on a cisco 877 router.
I have an interface e0/4 that is 172.1.1.1 on router one (network one) which links to another router (onnetwork two) which has an interface of e0/4 172.1.1.2 which allows two networks to communicate. Network one is 192.168.0.0 /24 and network two is 10.255.255.0 /24.
How do i configure netflow to monitor the traffic going through these interfaces?
Cisco WAN :: 2821 / Netflow Not Working On Multilink Interface
Feb 18, 2013I have a Cisco 2821 with two serial interfaces bundled using PPP multilink. I want to monitor traffic flow (net flow) on the multilink interface. I have tried configuring ip route-cache flow/ ip flow ingress / egress but no luck.The other thing is when I do sh ip cache flow I guess I should see the multilink interface in both Source and destination columns which is not happening (not showing in destination column).The other router with same config but with ATM sub-interface working properly (same IOS). Are there any hits on this ? Also, is it possible to use SPAN feature ? The monitoring server is at some other site (coming via WAN).
View 1 Replies View RelatedCisco WAN :: Configure NetFlow Top Talkers On ASR1002?
Sep 5, 2012I am trying to configure the NetFlow Top Talkers function on an ASR1002 with ADVENTERPRISEK9-M, Version 15.2(4)S. With this new Hardware and Software I am surprised to see that the command:
ip flow-top-talkers
top 50
sort-by packets
cannot be found on the CLI - it's just not there.
Cisco :: Configure Netflow And Templates On 12410 IOS 12.0?
May 6, 2013how to configure netflow on cisco 12410 router in order to get valid FLOWS on a Harvester i installed, i found a documente where mention how to configure but i receive an unknow template from routers, i think that i need to configre something else but dont know what, this is the router configuration i set:
[code]....
Cisco Switching/Routing :: Configure The IOS NetFlow 122-58.SE2 In A Catalyst 3560?
Jun 4, 2012It is possible to configure the IOS NetFlow 122-58.SE2 in a Catalyst 3560?
View 5 Replies View RelatedCisco :: Configure Netflow Catalyst 6500 With SUP720-10GE
Jun 5, 2012I tried to configure netflow without success.
Setup is the following.
Cisco Catalyst 6509 with Sup720-10GE IOS 12.2(33)SHX7. There are around 30 L3 vlans configured on the switch. I'm only interested for the traffic on one L3 vlan which is the connection to wan cloud.
I wanna see only the traffic that goes to and come from the wan. On other Catalyst where I have routed interfaces i successfully configured netflow. I read a lot in the forums and documentations but i didn't find the right one.
Why Layer 2 Switches Need Mac Address Even It Does Not Have Any Interface
Dec 27, 2011Why layer 2 switches need its mac address, even it does not have any interface ? (does not have stp and etc)
View 8 Replies View RelatedCisco :: 2951 - Interfaces Send Netflow Data Despite No Flow Config Under Interface
Aug 17, 2011Cisco 2951 w/ HWIC-4ESW
IOS 15.0(1)M5
#sh ip flow int
Vlan533
ip flow ingress
ip flow egress
#
The SVI sends the flow data just fine, however I also continue to receive flow data from most other interfaces.
I have attached a screenshot of one of our netflow collectors indicating that many of the interfaces are sending flow data even though not configured to do so. We have two different netflow collectors, from different vendors and both confirm the same interfaces sending flow data.
Normally I wouldn't care and ignore it, however one of them uses a license limit by interface and is a bit problematic.
Cisco WAN :: 3845 Port-channel Sub-interface QoS
Sep 13, 2012I have Cisco 3845 with two Gigabit interfaces configured as port-channel with subinterface and with QoS.However shape does not work, why? [code]
View 1 Replies View RelatedCisco Firewall :: Web Authentication On Layer 3 Interface With Cat 3750
Sep 12, 2012Cisco 3750 with IP Service Image 12.2.55, Trying to enable Web Authentication on Layer 3 interface:
!
ip auth-proxy name bp_auth_proxy http inactivity-time 60
!
interface GigabitEthernet1/0/5
no switchport
ip address 192.168.1.27 255.255.255.0
ip access-group 101 in
Cisco WAN :: Assign MAC ACL To Layer 2 Interface On 887VA Router?
Mar 24, 2013I wish to assign a MAC ACL to a layer 2 interface on an 887VA router but cannot seem to see how to do this.
View 2 Replies View RelatedCisco WAN :: 3845 Router - Disabled In Backup Interface
Sep 2, 2010I have a problem in configuring two pair of backup interface on my customer's router (3845). It's ok when I configure just one of them. If I configure both pairs of interfaces into backup interface, one of them will be in disabled mode, as shown below :
WANR01#sh ip int bri
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0 172.16.199.106 YES NVRAM up up
GigabitEthernet0/1 172.16.3.5 YES NVRAM up up
Serial0/0/0 unassigned YES NVRAM administratively down down
Serial0/0/1 unassigned YES NVRAM administratively down down
FastEthernet0/1/0 125.213.133.186 YES NVRAM standby mode down
FastEthernet0/2/0 172.112.22.6 YES NVRAM standby mode/disabled down
FastEthernet0/2/1 123.231.177.238 YES NVRAM up up
Loopback0 172.16.199.12 YES NVRAM up up
Cisco WAN :: 3845-MB Dropping Pings To Its Own Serial Interface?
May 16, 2013I'm having an issue that I can't quite understand. I set up a test lab to get familiar with EIGRP routing. I have a Cisco 3845-MB with 2 VWIC2-2MFT-T1/E1 cards.sh ip int brief shows UP UP status on all serial ports. I gave it an IP address but I'm having trouble pinging the serial interface IP. It's dropping pings to its own S 1/1/0 interface when pinging from console. I have known good T1 crossover cables 1&2 - 4&5.
Here is the "ip int brief" from 3845-MB
3845-MB#sh ip int brief
Interface IP-Address OK? Method Status Prot
ocol
GigabitEthernet0/0 unassigned YES NVRAM administratively down down
GigabitEthernet0/1 172.30.2.1 YES NVRAM up up
Serial1/1/0:0 10.3.29.2 YES manual up up
Right now it's pinging itself at about 60 -90% success rate... and I can't figure out why it's dropping any packets at all. I have other issues with in the lab as well... but i think this might be my "core" issue.To make matters even more "weird" I've tried two different VWIC2-2MFT-T1/E1 cards and I drop pings with both of them.
Here is a sh run and a sh diag:
3845-MB#sh run
Building configuration...
Current configuration : 1434 bytes
!
version 12.4
service timestamps debug datetime msec
[code].....
Cisco Switching/Routing :: 3845 Gigabit Interface
Oct 26, 2011We have a number of 3845 routers, some running IOS 12.4(22)T2 and earlier and some running 12.4(24)T4. On the ones with 12.4(22)T2 and earlier, gigabit interface g0/1 shows interface down/line protocol down when there is no cable connected to the interface and the interface is not in shutdown state. On the ones with 12.4(24)T4, gigabit interface g0/1 shows interface up/line protocol down when there is no cable connected to the interface and the interface is not in shutdown state. Interestingly in both cases, the "show controller g0/1" command shows " network link is down (NO CARRIER)" when there is no cable attached. It makes sense to us that the interface status would be down/down when there is no cable attached. It does not makes sense to us that the interace would be up/down. Did Cisco at some point change their philosophy on whether an interface should show down/down or up/down when there is no cable attached, or is this a bug?
View 1 Replies View RelatedCisco WAN :: 3845 - How To Create Multilink Interface And Assign IP
Oct 16, 2011I have a question regarding mlppp and bonding mpls T1 circuits. For the longest time we have been able to get by on one T1 circuit coming into our 3845 router. Well this T1 has now become congested and they are wanting to add bandwidth to this T1. We connect to the phone company via an MPLS T1 currently. So now it appears as though we are going to purchase another MPLS T1 circuit and bond the two T1's together. The way our network is currently set up, we utilize the same AS number on all of our remote routers regardless of location. Keep in mind I don't have any sort of mlppp set up at this moment, so unfortunately I can't post any configs. I'm just questioning the design portion and how to go about doing this.
Here is where my dilemma begins........
For every MPLS circuit we order on the remote end, we specifiy an IP for the remote router itself and one for the provider to assign to their equipment (the bgp neighbor statements). Now granted i'm no BGP extraordinaire, not even a novice really, but I don't understand how I am going to bring two T1 circuits into the same router (basically with 2 pairs of IP's). In order to bond the two T1's together, i'll need to create a multilink interface and assign an IP to that, but yet I still have 2 SETS of ip addresses. And if that isn't enough of a dilemma, I also need to spedify a neighbor statement in order for my AS to bind to the adjacent provider AS, but yet I have two IP addresses for that as well.
Cisco Switching/Routing :: Configure Egress Netflow In 6500 (VSS) With VS-S720-10G Supervisor?
Jun 9, 2013I'm trying to configure a egress netflow in a 6500 (VSS) with VS-S720-10G supervisor. I foud some old posts and understood that netflow wasn't supported on 6500 but i found a new document and it seems that netflow is supported in Supervisor Engine 2T:[URL] Does the netflow still not supported in VS-S720-10G? It's weird because the command is supported:
#sh run int vlan 4
Building configuration...
Current configuration : 353 bytes
!
interface Vlan4
ip address X.X.X.X 255.255.0.0
[cod]....
Cisco Switching/Routing :: Cannot Assign Ip Address To Layer 2 Interface In 878
Apr 19, 2012I have a cisco 878 router and I can’t assign ip address to it’s fast Ethernet interface. When I assign ip address give me this message: “you can not assign ip address to layer 2 interface”.
But I can not understand why give me this alert when I use a layer3 device?!
Cisco WAN :: 3750 - Establish Interface Dialer On Layer 3 Switch?
May 7, 2012Is it possible to establish a interface dialer on a layar 3 switch?Or is it only interface for routers?I have a c3750 switch (WS-C3750G-24T), and when i try to establish a dialer interface i get an error message:
[code]...
Cisco WAN :: QoS Policy Fail On Vlan Interface Of Router 3845
Aug 29, 2011I have configured a qos policy and I am trying to apply the policy to a vlan interface which is physically connected to a switch module port of a 3845 Router.When I try to apply, the message configuration failed appears.
View 4 Replies View RelatedCisco Switching/Routing :: 3845 NAT Translation In VLan Interface
Nov 20, 2011I have a cisco router 3845 with Etherswitch modules and one Vlan configured "172.16.6/24", many switch ports are assigned to this vlan. i would like to translate one IP address 172.16.6.200 to a new one "172.25.42.10" but need to keep the other IPs from "172.16.6/24" without changes. below is the configuration of vlan interface and switch port. [code]
View 8 Replies View RelatedCisco Switching/Routing :: SF 300-48 Layer 3 Switch Tried To Configure To Use
Aug 24, 2011I got one SF 300-48 layer 3 switch I tried to configure to use it in the office network.Unfortunately I'm unable to configure the VLAN settings.I need port one for input(VLAN2),port 7-15 for another vlan(vlan3) also need to connect with the vlan 4.port 15 is another vlan(vlan4) this is for wireless.Other ports are static.It doesn't get any connections with other vlans.I wish to know how to configure vlans in GUI mode.I tried , But I can't get the Vlan setting correctly.Also,I need to know how to communicate both vlans in GUI mode.
View 8 Replies View RelatedCisco Switching/Routing :: How To Configure L3 Etherchannel 3845 ISR
Jun 9, 2013When I try to add an IP address to a port-channel interface on a 3845 ISR I am getting an error that seems to imply that only L2 etherchanneling is possible. Am I missing something?Cisco IOS Software, 3800 Software (C3845-ADVIPSERVICESK9-M), Version 12.4(24)T8,
sfo-c3845-1#sho run int port-channel 1
Building configuration...
Current configuration : 31 bytes
!
interface Port-channel1
end
[code].....
Cisco Switches :: SG300 - Setting Management Interface In Layer 3 Mode
Jun 13, 2012How to set the management interface on a SG300 Switch in Layer 3 mode? I've some vlans configured on the switch with interfaces in each of them:
Vlan 100 (10.0.1.254 /24)
Vlan 200 (10.0.2.254 /24)
Vlan 300 (10.0.3.254 /24)
...
Vlan 900 (10.0.9.254 /24)
Now, the management interface is listening on all interfaces (IPs). But I would like to configure the switch to only listen on 10.0.9.254. What I need to configure or whether it is possible?
Cisco WAN :: 3845 Routers - Receive Multicast Stream Via Tunnel Interface
Feb 16, 2012I have two Cisco 3845 routers which receive a multicast stram via a tunnel interface, i.e Tunnel163 (PIM Dense mode is enabled). These routers are both connected to a LAN segment (FastEthernet0/1/0) where receivers are. [code] Router1 is the assert winner (highest IP address), it sees igmp joins request, but it's pruning the interface. It happens sometimes and it lasts until I manually issue clear ip mroute.Unfortunately I cannot migrate to Sparse Mode.
View 15 Replies View RelatedCisco Switching / Routing :: 3560 - Accessing Management Interface Using Layer 3 Link
Apr 9, 2012I am setting up a link between buildings that uses wireless links. I'm using Layer 3 routed ports on 2 3560 switches to handle the routing between sites. Normally I would just put these in a /30 and then the switches handle the rest. However, the wireless access points have a web interface for managing them that I want to be able to access, but it's only available on the single NIC that also carries traffic. What would be the best way of making this work? Should I make the link a /29 and give the access points an IP in the same range? If this is the case what do I use for the default gateway for the access points?
I have included a diagram to try to explain the issue clearer. The IP addresses in black are what I would do if this were a standard cable (and indeed this will work, but I wont be able to access the admin interface of the wireless AP) and the red ip addresses are the alternative if I use a /29 (but as I said, I'm not sure what to use for the default gateways).
Cisco Firewall :: 3845 - Open Port Range On Secondary IPs On Router Interface
Feb 12, 2013 I have 4 public IPs on Router 3845 interface FastEthernet 0/0/1. IP as below.
50.200.2.2
50.200.2.3 secondary
50.200.2.4 secondary
50.200.2.5 secondary
I wan to allow ports 80 to 90 on 50.200.2.3 for my webserver (192.168.10.50)
Cisco Switching/Routing :: 4948 - Difference Between Netflow / Netflow-Lite
Mar 13, 2012Any major difrrence between Netflow v/s Netflow-Lite?
I am trying to understand if Cisco 4948E can do the same job as Cisco 4500E or not and difference between Netflow v/s Netflow-Lite will work for me to select correct product.
Cisco Switching/Routing :: Possible To Configure QoS On 4500 Sup7 On Layer 3 Routed Port
Apr 26, 2013I want to know if is it possible to configure QoS on a 4500 Sup7 on a Layer 3 routed port like the following example (Similar to CBWFQ on IOS Router)?
View 3 Replies View RelatedCisco Switching/Routing :: Configure Two 3845 Routers To Act As DHCP Server / Relay?
Feb 14, 2012I am trying to configure two 3845 routers to act as dhcp server and dhcp relay. Clients are connected to the router that relays all dhcp requests to the vrf instance which is used to connect it to the router wich is running dhcp server.
Router1
ip vrf dhcp_dns
rd 8:1
int gi0/0
ip vrf forwarding dhcp_dns
ip address 192.168.200.5 255.255.255.248
[code]...
So far I can see dhcp requests coming from the R1 and dhcp server on R2 replies with the dhcp offer but PC is not getting any ip.