I am trying to configure the NetFlow Top Talkers function on an ASR1002 with ADVENTERPRISEK9-M, Version 15.2(4)S. With this new Hardware and Software I am surprised to see that the command:
ip flow-top-talkers
top 50
sort-by packets
cannot be found on the CLI - it's just not there.
I need to know if I can pull Netflow style data (Top Talkers, Top Sessions, etc) from ASA 5505s? We are looking at buying some but I need to be able to export this kind of data to my managment station which is also a collector. I have read on this forum that 8.2 and above should support Netflow but I have read conflicting information.
View 2 Replies View RelatedI am going to configure the NATing on ASR1002 and expecing to have near about 1Million nat translation. Will ASR1002 support 1million nat translations ? how many NAT translations are supportable on the ASR1002 ?I am going to configure NAT on ASR1002-5G/K9 U& have FLASR1-FWNAT-RED.
View 1 Replies View Relatedhow I configure netflow on a cisco 877 router.
I have an interface e0/4 that is 172.1.1.1 on router one (network one) which links to another router (onnetwork two) which has an interface of e0/4 172.1.1.2 which allows two networks to communicate. Network one is 192.168.0.0 /24 and network two is 10.255.255.0 /24.
How do i configure netflow to monitor the traffic going through these interfaces?
how to configure netflow on cisco 12410 router in order to get valid FLOWS on a Harvester i installed, i found a documente where mention how to configure but i receive an unknow template from routers, i think that i need to configre something else but dont know what, this is the router configuration i set:
[code]....
Is it possible to configure more than one layer 3 interface for netflow on a 3845? I can't seem to do it. Is there something I am missing?
View 2 Replies View RelatedIt is possible to configure the IOS NetFlow 122-58.SE2 in a Catalyst 3560?
View 5 Replies View RelatedI tried to configure netflow without success.
Setup is the following.
Cisco Catalyst 6509 with Sup720-10GE IOS 12.2(33)SHX7. There are around 30 L3 vlans configured on the switch. I'm only interested for the traffic on one L3 vlan which is the connection to wan cloud.
I wanna see only the traffic that goes to and come from the wan. On other Catalyst where I have routed interfaces i successfully configured netflow. I read a lot in the forums and documentations but i didn't find the right one.
I'm trying to configure a egress netflow in a 6500 (VSS) with VS-S720-10G supervisor. I foud some old posts and understood that netflow wasn't supported on 6500 but i found a new document and it seems that netflow is supported in Supervisor Engine 2T:[URL] Does the netflow still not supported in VS-S720-10G? It's weird because the command is supported:
#sh run int vlan 4
Building configuration...
Current configuration : 353 bytes
!
interface Vlan4
ip address X.X.X.X 255.255.0.0
[cod]....
I wish see the top talkers 10 at the my router 2800 IOS 12.4 (13a)
but when I run the command "show ip flow top-talkers" appear following:
% Top talkers not configured
I've set
Router(config)#ip flow-top-talkers
Router(config-flow-top-talkers)#top 10
I'm using the netflow version 9
maybe my router not support this issue ?? or it's missing some configuration.
We ahave ASA 5510 and 5520 @ our office. We are not using any netflow tools in order to get the talk talklers.As this firewalls are shared firewall (used by different Projects), we are not able to get , which project is using more traffic and which is less.
View 3 Replies View RelatedAny major difrrence between Netflow v/s Netflow-Lite?
I am trying to understand if Cisco 4948E can do the same job as Cisco 4500E or not and difference between Netflow v/s Netflow-Lite will work for me to select correct product.
Right now I have a ASR1002 running a very old IOS version.Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 12.2(33)XNE, RELEASE SOFTWARE (fc1) asr1000rp1-ipbasek9.02.05.00.122-33.XNE.bin – 25-NOV-2009?
I am looking to upgrade to a newer version.I was wondering if there are any tricks when upgradeing this IOS. Is it as easy as loading the IOS onto the ASR and then changing the bootpath or is there an upgrade path I must follow? Also would there any need for a licence between 2.x and 3.x.
The loopback of the ASR1002 is 2.2.2.2. When I use a browser to access it, I got the authentication dialog box asking for username/password. I input the information and submit. But authentication box comes back again and ask for the username/password.
The username/password is test okay. But somehow, the web GUI just does not use it.
Is the GLC-LH-SM SFP compatible with the ASR1002 and how does it differ from the SFP-GE-L adapter?
View 4 Replies View RelatedWe have an ASR1002 with asr1000rp1-adventerprisek9.03.05.01.S.152-1.S1.bin software.I couldn't find any documentation on how to attach an L2 interface, in my case a subinterface with a single dot1q vlan, to a BDI interface.I'm able to create a bridge-domain interface but it's down down.The command bridge-domain on the subinterface url...
View 2 Replies View RelatedI'm aware ACL's are handled in hardware on the ASR platform but wondered if there was any way to inspect how many hits we get on each line of an ACL on the ASR, I can't seem to find a command to do this.
Using LOG is not possible due to the large number of hits.
One of our customer just purchased ASR1002 router, they have three internet links from different ISPs and they dont have any remote site, they have three different public IP pool as their respective ISPs. So, is it possible to load balance the internet traffic using all three link on Cisco ASR router ( IOS - Advance Enterprise Services)
View 3 Replies View RelatedWe have a cisco7206 router which is going to be replaced with an ASR1002 router. The 7206 has some interfaces in a BVI-group - the config of which i am trying to translate over into IOS XE (which runs on the ASR1002). How to translate this config from IOS to IOS XE.
View 3 Replies View RelatedWe are having an issue with BGP flapping peer. We have a ASR1002 as Route Reflector and it work fine with all peers except with 2 peers.
View 3 Replies View Relatedim trying to create a VPN between a Cisco ASA5510 and an ASR1002 when my Loopback interface is The Source IP . [code]
View 1 Replies View Relatedwhat command is required to configure ip accounting on an interface?
I would have thought to what is required is on the interface, turn on Ip accounting i.e.
int gi0/0/0
ip accounting
However, there is no ip accounting command within the interface. We are running version Version 15.1(1)S2.
During the boot ios we found the error messages below. How can i clear this messages?
Missing or illegal ip address for variable DEFAULT_GATEWAY Using midplane macaddr
Missing or illegal ip address for variable IP_ADDRESS
Missing or illegal ip address for variable IP_SUBNET_MASK
I've inherited a project building an internet connectivity solution for a large corporate. It has its own AS and its own PI space. They are putting in 100Mbit connections from 5 different Tier1's , taking full internet routing from each. Cisco ASR1002's have already been specified and purchased for the job. I'm not familiar with the ASR platform at all - is it up to the job with full routing tables? multiple instances of full tables ? (not likely to put all 5 into one box!)
View 2 Replies View Relatedwe are using an ASR 1002 for dynamic NAT (with route maps). I do have a Problem with the usage of the NAT pool it self.The total NAT Translations for the pool are:
#sh ip nat stat
[Id: 1] route-map natted-host-01 pool nat-pool-01 refcount 136
pool nat-pool-01: netmask 255.255.254.0
start XX.XX.202.0 end XX.XX.203.255
type generic, total addresses 512, allocated 88 (17%), missee 0
If i now look into the NAT translation Table i do get less entries:
#sh ip nat translations filter map-id dynamic 1 total Total number of translations: 43
Only a deeper look into the QFP gives here the right values:
# sh platform hardware qfp active feature nat data The ouput count matches the values I get if i isue a sh ip nat stat
My question is how is it handled internally.
We do have a problem too, with raising usage of the pool over the time.Once allocated Pool entries are not released after a period of time. And no NAT translation occur for that used IP NAT pool Addresses.
The timer on the device are set:
ip nat translation timeout 300
ip nat translation tcp-timeout 900
ip nat translation pptp-timeout 900
ip nat translation udp-timeout 120
ip nat translation routemap-entry-timeout 900
ip nat translation max-entries 750000
I am trying to bring up a couple of ASR's. They are fitted with SPA modules (SPA-8X1GE-V2). These have SFP modules GLC-T fitted into them. For the life of me I cannot get these ports to come up. If I have a look at the inv the SFP's show as GE-T's (physically they are GLC-T's)
Is there a compatability problem with these GLC-T's on ASR 100x?
we are testing an ASR1002-X which acts as LNS for L2TP tunnels.
- All tunnels are UP (sh vpdn all return list of tunnels)
- VirtualAccess interfaces are UP
- C routes are added in routing table
but ping remote IPs don't work !!! [code]
I have recently purchased ASR1002-RP1-ESP5 with 2 x 4K Broadband licenses to be used as LNS. Cisco have sent me PAK files for the licenses however when I try to enter the licenses into the device I get an error message saying that Licensing is not supported on this platform.
Any experience with this platform and installation of the broadband licenses?
When I spoke to Cisco TAC they told me that for this particular model the licensing is on "trust" basis where you buy license and do not install it on the actual router - similar to what 7200 used to do.
We recently purchased a Cisco ASR1002 router with four on-board Gigabit SFP-style Ethernet ports. However, when I do a "show ip interface brief", I see that there's an extra Gigabit Ethernet port. See the last interface in the following output:
ASR_1002_router#sh ip int b
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0/0 unassigned YES manual down down
[Code].....
On the router itself, in addition to the four Ethernet SFP ports, there are four additional RJ-45 ports. They're labeled "BITS", "MGMT", "CON", and "AUX". I know what the Con and Aux ports are, but what are the Bits and Mgmt ports? And is one of them the Gigabit Ethernet interface that I see listed at the bottom of the output? And if it is, is there anything special about it, or is it just another routed Ethernet port? Can I do something special with it, like out-of-line managment?
We have ASR1002 routers configured to run individual SubPackages, at this point everything is operating without problems.We just received a Cisco Security Advisory informing us SSHv2 is vulnerable in our version of router code.We have to upgrade to the recommended stable release, so we downloaded, installed and expanded the IOS to expose the SubPackages on the ASR routers bootflash.
Since we are running SubPackages, do we need to upgrade all SubPackages (I.E. complete IOS upgrade) of can we just upgrade the vulnerable SubPackage? How do you determine which SubPackage contains the SSHv2 application?
We are testing an ASR1002-X which acts as LNS for L2TP tunnels.
- All tunnels are UP (sh vpdn all return list of tunnels)
- VirtualAccess interfaces are UP
- C routes are added in routing table
but ping remote IPs don't work !
LNS1# sh ver
Cisco IOS Software, IOS-XE Software (X86_64_LINUX_IOSD-UNIVERSAL-M), Version 15.3(2)S1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[Code].....
We are trying to implement the ZBF on our router to assist us in limiting the intial impact of DDOS attacks.We have configured the below and it appears that it's not working, as when un der attack the statistics don't increae.
[code]...
How to configure SSH on a ASR 1002 and apply it to the Management Interface?
View 3 Replies View Related
