Cisco WAN :: 3845 Router - Disabled In Backup Interface
Sep 2, 2010
I have a problem in configuring two pair of backup interface on my customer's router (3845). It's ok when I configure just one of them. If I configure both pairs of interfaces into backup interface, one of them will be in disabled mode, as shown below :
WANR01#sh ip int bri
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0 172.16.199.106 YES NVRAM up up
GigabitEthernet0/1 172.16.3.5 YES NVRAM up up
Serial0/0/0 unassigned YES NVRAM administratively down down
Serial0/0/1 unassigned YES NVRAM administratively down down
FastEthernet0/1/0 125.213.133.186 YES NVRAM standby mode down
FastEthernet0/2/0 172.112.22.6 YES NVRAM standby mode/disabled down
FastEthernet0/2/1 123.231.177.238 YES NVRAM up up
Loopback0 172.16.199.12 YES NVRAM up up
View 5 Replies
ADVERTISEMENT
Aug 29, 2011
I have configured a qos policy and I am trying to apply the policy to a vlan interface which is physically connected to a switch module port of a 3845 Router.When I try to apply, the message configuration failed appears.
View 4 Replies
View Related
Apr 26, 2011
I'm about to install a new E1 onto my 3845 as backup line for my data network. We usually use VWIC2 cards since our infrastructure covers EU and US sites. But this time, I ran out of stock and so did my supplier. I have a VWIC-1MFT-G703 card here but not sure if it would work. What is the difference compared to the regular VWIC-1MFT-E1 ?
FYI, I run 12.4 T train release on my 3845s.
View 3 Replies
View Related
Feb 12, 2013
I have 4 public IPs on Router 3845 interface FastEthernet 0/0/1. IP as below.
50.200.2.2
50.200.2.3 secondary
50.200.2.4 secondary
50.200.2.5 secondary
I wan to allow ports 80 to 90 on 50.200.2.3 for my webserver (192.168.10.50)
View 5 Replies
View Related
Feb 2, 2007
We have a RV042. remote management is set to DISABLE - but even after restarting the router i can access the interface remotely over the internet.even when i enable it and change the port to say 5555 i can connect to the web interface using either port 5555 but ALSO on port 80.what's wrong here?the only way to stop that was to create a rule that blocks port 80 on the WAN interface. (btw. could this rule affect LAN users when browsing the web?)
View 7 Replies
View Related
Apr 11, 2012
When mls qos is disabled, how much of an interface buffer is available to the single output queue?is a single switch port able to consume as much as required of the common memory pool.
View 7 Replies
View Related
Sep 26, 2012
I have an Ethernet Loopback Plug (4 Pairs) made and trying to test the Gigabit Interface on a 3845 Router with a fail result. The interface will show up/up only if I set the interface to 100M/Full Duplex when I plug-in the Ethernet Loopback Plug (4 Pairs). I don't see this Gigabit Interface @ 3845 router has any option to set it to internal or external loopback.
View 2 Replies
View Related
Feb 24, 2011
I have disabled Unicast RPF on a Cisco ASA 5510 for one specific interface. However, how do I verify that RPF indeed has been disabled on that particular interface? It doesn't show up in the config, neither does it up when I issue the command "sh int interface'.
To disable the RPF feature, I issued the following command: no ip verify reverse-path interface interface_name
View 1 Replies
View Related
Oct 1, 2011
ok i got a toshiba a15-s129 and yet its not enabled the wifi .. the light is amber and i got the module drivers and the function keys .. i hit the function + f8 yet nothing and i also have the software for atheros and yet it says wireless network interface disabled? any clue on how to enable this wireless or how to disable the hotkeys so it will not find any settings for it ...?
View 1 Replies
View Related
Sep 13, 2012
I have Cisco 3845 with two Gigabit interfaces configured as port-channel with subinterface and with QoS.However shape does not work, why? [code]
View 1 Replies
View Related
Mar 20, 2013
Is it possible to configure more than one layer 3 interface for netflow on a 3845? I can't seem to do it. Is there something I am missing?
View 2 Replies
View Related
May 16, 2013
I'm having an issue that I can't quite understand. I set up a test lab to get familiar with EIGRP routing. I have a Cisco 3845-MB with 2 VWIC2-2MFT-T1/E1 cards.sh ip int brief shows UP UP status on all serial ports. I gave it an IP address but I'm having trouble pinging the serial interface IP. It's dropping pings to its own S 1/1/0 interface when pinging from console. I have known good T1 crossover cables 1&2 - 4&5.
Here is the "ip int brief" from 3845-MB
3845-MB#sh ip int brief
Interface IP-Address OK? Method Status Prot
ocol
GigabitEthernet0/0 unassigned YES NVRAM administratively down down
GigabitEthernet0/1 172.30.2.1 YES NVRAM up up
Serial1/1/0:0 10.3.29.2 YES manual up up
Right now it's pinging itself at about 60 -90% success rate... and I can't figure out why it's dropping any packets at all. I have other issues with in the lab as well... but i think this might be my "core" issue.To make matters even more "weird" I've tried two different VWIC2-2MFT-T1/E1 cards and I drop pings with both of them.
Here is a sh run and a sh diag:
3845-MB#sh run
Building configuration...
Current configuration : 1434 bytes
!
version 12.4
service timestamps debug datetime msec
[code].....
View 4 Replies
View Related
Oct 26, 2011
We have a number of 3845 routers, some running IOS 12.4(22)T2 and earlier and some running 12.4(24)T4. On the ones with 12.4(22)T2 and earlier, gigabit interface g0/1 shows interface down/line protocol down when there is no cable connected to the interface and the interface is not in shutdown state. On the ones with 12.4(24)T4, gigabit interface g0/1 shows interface up/line protocol down when there is no cable connected to the interface and the interface is not in shutdown state. Interestingly in both cases, the "show controller g0/1" command shows " network link is down (NO CARRIER)" when there is no cable attached. It makes sense to us that the interface status would be down/down when there is no cable attached. It does not makes sense to us that the interace would be up/down. Did Cisco at some point change their philosophy on whether an interface should show down/down or up/down when there is no cable attached, or is this a bug?
View 1 Replies
View Related
Oct 16, 2011
I have a question regarding mlppp and bonding mpls T1 circuits. For the longest time we have been able to get by on one T1 circuit coming into our 3845 router. Well this T1 has now become congested and they are wanting to add bandwidth to this T1. We connect to the phone company via an MPLS T1 currently. So now it appears as though we are going to purchase another MPLS T1 circuit and bond the two T1's together. The way our network is currently set up, we utilize the same AS number on all of our remote routers regardless of location. Keep in mind I don't have any sort of mlppp set up at this moment, so unfortunately I can't post any configs. I'm just questioning the design portion and how to go about doing this.
Here is where my dilemma begins........
For every MPLS circuit we order on the remote end, we specifiy an IP for the remote router itself and one for the provider to assign to their equipment (the bgp neighbor statements). Now granted i'm no BGP extraordinaire, not even a novice really, but I don't understand how I am going to bring two T1 circuits into the same router (basically with 2 pairs of IP's). In order to bond the two T1's together, i'll need to create a multilink interface and assign an IP to that, but yet I still have 2 SETS of ip addresses. And if that isn't enough of a dilemma, I also need to spedify a neighbor statement in order for my AS to bind to the adjacent provider AS, but yet I have two IP addresses for that as well.
View 2 Replies
View Related
Nov 20, 2011
I have a cisco router 3845 with Etherswitch modules and one Vlan configured "172.16.6/24", many switch ports are assigned to this vlan. i would like to translate one IP address 172.16.6.200 to a new one "172.25.42.10" but need to keep the other IPs from "172.16.6/24" without changes. below is the configuration of vlan interface and switch port. [code]
View 8 Replies
View Related
Dec 9, 2012
I have an ASA 5510 running 8.4 with dual ISPs setup on 2 different interfaces: outside(primary),backup(backup). I also have a site to site VPN to another ASA in another city. The VPN is now setup on the outside interface and works fine. What I wanted to do is to make the VPN run over the backup interface only.
So, I modified the the crypto map on the remote side to use the backup interface IP and created a tunnel-group for it. I then created a crypto map for the backup interface and enabled ikev1 on it. The default route is set to use the outside interface so I created a static route that routes traffic bound for the outside interface on the remote side to the backup interface default gateway. I can get the tunnels to establish but no traffic is passing through them. I though then that I need a NAT for the tunnel traffic to I created a NAT as well but still no traffic passed. I tried the packet-tracer and it said the traffic was allowed and from the show crypto ipsec sa command I can see the tunnel setup but no traffic will go across it.
View 5 Replies
View Related
Feb 16, 2012
I have two Cisco 3845 routers which receive a multicast stram via a tunnel interface, i.e Tunnel163 (PIM Dense mode is enabled). These routers are both connected to a LAN segment (FastEthernet0/1/0) where receivers are. [code] Router1 is the assert winner (highest IP address), it sees igmp joins request, but it's pruning the interface. It happens sometimes and it lasts until I manually issue clear ip mroute.Unfortunately I cannot migrate to Sparse Mode.
View 15 Replies
View Related
Jun 20, 2011
Does backup interface is supported on ASR?
interface GigabitEthernet0/2/1
description 3750_Stack_1
backup interface GigabitEthernet0/2/2
ip address 100.50.50.242 255.255.255.248
View 7 Replies
View Related
Nov 21, 2011
I have setup ASA 5505 with 2 ISP, named outside (primary) and backup, the scenario is if outside down, then backup will take over, it works now. But it is not working when the primary connection cannot reach the gateway with the interface still up.
Is it possible when the primary connection cannot reach the gateway then backup automatically take over?
My configuration is:
ASA Version 8.2(1)
!
hostname cisco
[Code].....
View 4 Replies
View Related
Nov 12, 2012
We have a 5510 and I have a second ISP setup for a backup link. We have 4 ports connected to 4 different internal subnets. I want to force one of the ports to use the backup ISP link at all times. I'm having a little problem with where I need to make the changes in my ASA.
Interface "outside" is my main ISP
Interface "building3" is my backup ISP.
I want to force the "Guest" network to use the "building3" link for all traffic. Here's a snippet of my config
global (outside) 10 interface
global (building3) 10 interface
nat (inside) 0 access-list nonat
nat (inside) 10 0.0.0.0 0.0.0.0
nat (Guest) 10 0.0.0.0 0.0.0.0
[URL]
Do I need to change the global pool or create a new one? I have a couple free public IP addresess on the building3 subnet I can use for a pool.
View 2 Replies
View Related
Jan 18, 2011
I have two 3750 switch.switch A(main) and switch B is connected by OFC but i have another wireless link for backup.Now if OFC goes down then i manually connect wireless link with switch B for this reasons i am faceing a lot of problem. I want without any changing of cable if my primary link goes down then my backup link automaticaly goes up and vice versa .
Switch-A port gi1/0/9 and Switch-B port gi1/0/9 is connect by OFC Switch-A port gi1/0/8 and Switch-B port gi1/0/8 is connect by Wireless link (backup) i attach my network diagram kindly find the attachment file.
View 3 Replies
View Related
Sep 8, 2012
Since WLC5508 MGMT interface is configured a AP-Mgr at the same time, can I set a Backup Port to WLC5508 MGMT interface? Refer to WLC configuration Guide:
In the Backup Port text box, enter the number of the backup port assigned to the management interface. If the primary port for the management interface fails, the interface automatically moves to the backup port.
Note Do not define a backup port for an AP-manager interface. Port redundancy is not supported for AP-manager interfaces. If the AP-manager interface fails, all of the access points connected to the controller through that interface are evenly distributed among the other configured AP-manager interfaces
if I need to configure the backup port for MGMT interface, i need to remove the AP-manager on MGMT interface and create a network dynamic interface for AP-Manager ?
View 2 Replies
View Related
Apr 27, 2011
i will going to buy a router 2911 but i want know if support a interface ADSL modulo like backup in case that my primary link WAN Ethernet down and up the adsl link with a module HWIC ADSL pots.
View 1 Replies
View Related
Jan 20, 2013
Here's my problem. I'm going to be using Cisco 1941 routers at a bunch of remote sites. All of these sites have 2 comm paths out. Some of them have 2 IP/VHF radios and some have 1 IP/VHF radio and a copper link using Patton ethernet extenders. From the VHF radios the data hit our MPLS network back to our HQ and the sites with copper go directly back to our HQ. Everything ends up at a Cisco 4948 switch. The problem I'm having is that I want the routers at the remote site to use one ethernet port (G0/0) as the primary and the other (G0/1) as the backup interface. I've tried the backup interface command but the problem is that depending on where an outage occurs the ethernet link to either the radio or Patton stays up so it never switches over. We're using OSPF as our routing protocol and I'm sure there's something that can be done with it but I'm not sure what.
View 4 Replies
View Related
Oct 16, 2011
I have a asa 5520 with an outside and backup interface. I am trying to configure two static nat statements from the inside to the outside and backup interface. Here is what I have configured so far.
object network obj-10.1.1.254
host 10.1.1.254
object network obj-10.1.1.254
nat (inside,outside) static 172.25.10.3
I want to also use nat (inside,backup) static 172.25.10.3
View 3 Replies
View Related
Dec 10, 2012
Is there any physical or technical diferrences between PWR-3845 AC/2 and PWR-3845 AC? We are trying to order replacement parts and wondering if PWR-3845 AC is for one power supply and AC/2 means you get two with one order?
View 1 Replies
View Related
Dec 7, 2012
Is there any physical or technical diferrences between PWR-3845 AC/2 and PWR-3845 AC? We are trying to order replacement parts and if PWR-3845 AC is for one power supply and AC/2 means you get two with one order.
View 1 Replies
View Related
Aug 22, 2011
Recently I have bought a 2821 router from an auction. The router did have some configuration and password on it. I tried to break into it by restating it and pressing control and pause break signal. Old cisco method. Now when I try this method on my 2821. It does say that password recovery is disabled on the router. After this message router proceed with normal boot process. How to break the password ? Even if I loose the configuration.
View 4 Replies
View Related
May 9, 2012
i have a 1841 cisco router and i recently purchased a 1 port HWIC wan interface card. My problem is that I cannot see the interface in my config file. Is there something i am missing?
View 8 Replies
View Related
Apr 9, 2011
Is it possible to set up a WAN interface on a FastEthernet interface of a Cisco 877 Adsl Router ?Due to my ISP, i've to use an external VDSL modem and must connect it to my cisco 877 router (and leave it's adsl interface unused).But i don't know how to set up a wan port, other than the adsl interface itself (dialer0), on my cisco.
View 7 Replies
View Related
Mar 24, 2011
I am installing Cisco blank CF upgrades (double the capacity of the CF that came with the router) in Cisco 3845 routers and I cannot get the IOS to load.
Network security requires tftp be disabled, so I am limited to xmodem. Slow, but it works. I know the IOS download is good, because I can load it on the CF that came with the router.
I can install, format and read the new flash. But the download locks up and bombs about 1/3 of the way through.
Note: CF that came with the router was "C" so I used the format flash: command. The new flash reads the same as the old, except that there is no file IOS loaded.
I've never had an issue upgrading an IOS, but this is my first shot at installing on a new CF.
View 10 Replies
View Related
Apr 26, 2011
1841 & 3845 router. We send 30 GB data on 100 Mbps link. First time we use 3845 router for sending the data and 47 Min are required to complete the data, during this link utilization was 100%. After that we send same data through 1841 router & 46 Min are required for the same. Only difference in data transfer is CPU Utilization of 1841 router goes 30% & 5 % of 3845 router Can we use 1841 router instead of 3845 router ? .
View 2 Replies
View Related
Apr 26, 2011
I have 3845 router where 200 branches are connect. Ho have database server where branch are synch interval period.some of days observation cpu load average 70 % and sometimes it reaches 100 %.yesterday when I give command clear arp then instant cpu load reduce and 20 % yesterday cpu load 12-20 %. Today morning when I give command Cpu proc history then I found cpu load 60 % and at night it was 3 times reaches 100 %. so my question is after clear arp command at least 10 hours cpu utilization 20 % but after that it increase.so for any LAN broadcast it happend ? how i understand cpu high for Broadcasting or anything else.
View 2 Replies
View Related
