Cisco WAN :: Dumping Down A 886va To A Pure VDSL Modem
Mar 17, 2013
I want to dumb down a Cisco 886va to act as a pure vdsl bridge modem with a local ip to be able to do some admin work on the router. To some extent my config works, but i think the default vlan 1 kills my internet. When i connect the 88va the vlan bridge 7 and 8 goes up, the router behind connects via pppoe on vlan 7 but no traffic is going through. vlan 8 gets a dhcp lease for iptv and if i don´t switch the receiver on and off the traffic flows and the tv works. I am also able to connect to the local ip to access the web interface. [code]
View 1 Replies
ADVERTISEMENT
Aug 8, 2011
I will install in the next days a 886VA router (VDSL over ISDN using PPoE). Since I have no possibility to verify the VDSL config, this is what i prepared. Is this config OK (only VDSL part) ?
controller vdsl 0
operating mode auto
interface Ethernet0
[ code]...
For VDSL over ISDN the interface Ethernet0 must be used instead of ATM . Is this config correct ?
View 5 Replies
View Related
Jul 3, 2011
I'm using a Cisco 886VA connected to an ADSL2+ line. Typing "sh control vdsl 0 | inc Err" shows me the CRC errors on the line, but the CRC error counter displayed with "sh int atm 0" is empty. Also with 876 typing "sh dsl int atm 0" I can see growing error rate but "sh int atm 0" is empty.
I want to write an applet to reset the interface/controller if threshold is too high but the event interface detector won't see any errors.
View 2 Replies
View Related
Nov 25, 2011
I have a dir 655 coupled with a 320b modem for adsl. Now I must switch to VDSL. Can I use the router with a VDSL Modem? Which modem could be used ? I do not see dlink products ..
View 14 Replies
View Related
Oct 20, 2012
I recently upgraded my DSL service, which required installing a new VDSL modem/wireless router (Actiontec c1000a.) Before the upgrade, I was using an older standalone DSL modem with a Netgear router to provide wireless access to my gaming consoles, laptop, etc. Everything works as before with my new wireless router EXCEPT my son's laptop. All my consoles, iPods, and desktop CAN connect to the wireless network, and the laptop will connect over a WIRED ethernet connection. I cannot get it to connect to the wifi.
[code]....
View 6 Replies
View Related
Nov 10, 2012
I desperately try to set up the X3000 as a router behind a vDSL modem. When I choose connection through Ethernet and then PPPoE, it never keep the credentials after reboot in spite of having saved the data before.
View 6 Replies
View Related
Apr 25, 2013
I just bought a 5505 to learn from and am trying to attach my VDSL modem as a transparent bridge.It goes....
Laptop >>> (VLAN1) Cisco 5505 (VLAN2) >>> VDSL modem >>> internet
X.X.X.10 >>> (X.X.X.254) ------ (Y.Y.Y.254) >>> Y.Y.Y.10 >>> A.B.C.D.
I'm using the ASDM, if I configure VLAN2 with the IP address of the VDSL interface I can ping the modem from the console session via Putty. If I take that off and configure up the PPPOE client I can't ping the VDSL modem, I'd expect that. If I then add in an IP address to the PPPOE client config like I assigned to VLAN2 it doesn't ping either.If I can't ping the VDSL modem I don't expect it would work but it seems I can only either give it a static address which pings but has no pppoe or give it a PPPOE config which means I can't ping the VDSL. why I can't ping the VDSL modem when the interface is set as PPPOE with an IP address?Presumably if I'm on the ASA console doing pings from there to the modem then I'm ruling out problems with the routing from the laptop (trying to isolate where the issue is)
View 3 Replies
View Related
Apr 4, 2012
I have a DIR 655 which I am trying to use as a pure access point for a network based on a Comcast SMC Modem/Router On the DIR 655 I have the DHCP turned off and on the Internet Connection I have given the DIR 655 a static address of 10.1.10.2 with Gateway and Primary DNs 10.1.10.1 (The SMC is 10.1.10.1) I have the DIR 655 connect to the SMC Lan to Lan. DIR 655 is G only to deal with and IPAD issue....
The wireless devices get an internet connection BUT... I can only contact the DIR 655 wirelessly the SMC does not show the DIR 655 as connected I can not ping the DIR-655 from the SMC. I can " see" the static addresses I have given to two network cameras but they don't not respond to Port Forwarding I have assigned at the SMC (that is more for info as I realize that might be a SMC issue) . How to make the DLIK visable to the wired network.
View 14 Replies
View Related
Feb 20, 2012
Does this board supports DirectIO to PCIe devices? I have one, and there is an option in the BIOS for IOMMU (disabled or 64mb) which dosent seem relevant? But ESXi dosent see support for pass through.
View 1 Replies
View Related
Mar 2, 2013
i used a Cisco 886VA with Annex-B service in Germany. Now the provider has changed the DSLAM port to Annex-J but the router does not get any connection anymore.
As per Cisco homepage [URL] the router should support Annex-J in table 7:
Cisco 886VA: Optimized for Annex B; also compatible with Annex J
How to bring up the router with Annex-J service?? Is there something special i have to configure? Do i have to buy Cisco 886VA-J???
Software i have tested:
==========================================
c880data-universalk9-mz.151-4.M4.bin
c880data-universalk9-mz.153-1.T.bin
[Code].....
View 1 Replies
View Related
Jul 24, 2012
I have got a laptop and Desktop both of them have windows 7 ultimate OS and both of them have Kaspersky Pure V9.1 0.124 ( b ).
At home from the laptop I can access a shared folder on the desktop with no problem
I tried to enable the access to the shared folder over the internet while the laptop away from home, by implementing a VPN. I have successfully managed to configure a VPN IPSec between home router DrayTek 2820Vn that acting as VPN server, and the laptop that has TheGreenBow VPN client.
Through VPN tunnel laptop can ping the ip address for the router and the ip address for home printer and the ip address for home desktop , all of those are located at the other end of the VPN tunnel.
And I can access the web interface for the router as well by typing its private ip address. On the laptop and through the VPN tunnel I tried to map the shard folder on the desktop (\desktopipaddressSharedFolderName) , but it didn't work!!!.
when I existed Kaspersky on the desktop , I was able ping the desktop and to map the shared folder which is hosted on the desktop
How can I configure Kaspersky to let the the shared folder to be mapped via VPN ?
View 3 Replies
View Related
Jun 25, 2011
I've bought a new Cisco 886VA and want to set the noise-margin value. With my old 876 I had to set "service internal" and then I was able to configure the value unter ATM inter config.
But with the new 886VA I can't find a way to configure it.
View 5 Replies
View Related
Feb 3, 2011
it's across 3 floors and the current setup is a single wireless router DIR655 (1st floor), but the WiFi suffers greatly on the floor below/above.
I have sourced 3x D link switches and 2x more DIR655's and would like to have all machines/consoles/phones etc in the household on the same network. Is it possible to keep one DIR655 as the main wireless connection and have the other as pure AP's as well as keeping the same SSID?
View 1 Replies
View Related
Oct 28, 2012
I'm trying to configure multicast between 2 VLANs on a Cisco 886VA running IOS 15.2 (3) T1 (advanced security). While I can set the global "ip multicast-routing" I cannot "ip pim sparse-mode" on my interfaces - ip pim is actually unknown and also doesn't appear in the interface's ip subcommand list when using "?".
The feature navigator says pim is supported on my platform and IOS version.
My config looks like this:
interface FastEthernet3
switchport access vlan 103
no ip address
[Code].....
View 2 Replies
View Related
Mar 28, 2012
Is there a way to find in a remote branch the adsl line number in a cisco router 886VA.
When giving show controllers vdsl 0
we can see the upload/download speed but there is no information about the line number. We need this information in order to troubleshoot adsl line problems with our ISP's in remote branch offices.
View 3 Replies
View Related
Apr 8, 2013
Setup:
Cisco 886VA-K9
Cisco IOS Software, C880 Software (C880DATA-UNIVERSALK9-M), Version 15.2(4)M3, RELEASE SOFTWARE (fc2)
This router has two VLAN's on one Ehternet interface
VLAN1: data
VLAN2: voice
The WAN connection is a regular DSL line with PPP.
Modem FW Version: 120306_1254-4.02L.03.B2pvC035j.d23j
Modem PHY Version: B2pvC035j.d23j
Output of show interface brief:
Interface IP-Address OK? Method Status Protocol
ATM0 unassigned YES NVRAM up up
BRI0 unassigned YES NVRAM administratively down down
BRI0:1 unassigned YES unset administratively down down
[code]....
We all know you can't manage data traffic on the internet since your not in control of both sides of the link. So only queuing would not be a good practice IMHO. I was thinking on just rate-limit or police data-traffic so Voice always has bandwidth available when needed. I've did tried to rate-limit on the ATM0 interface, but no luck. Voice was still very bad.
My question is: where to rate-limit the data traffic? On the VLAN interface, the ATM interface, DIALER interface?
View 7 Replies
View Related
Oct 15, 2012
I am configuring ISDN Interface on 2 Cisco 886VA Version 15.2(3)T . I am unable to set ppp multilink on the BRI0 interface and on the dialer interface. It's like the command doen't exist anymore.How can I fix that so that i can have 128 K bandwidth between ma 2 sites ?.
Router1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router1(config)#int bri0
Router1P(config-if)#ppp multilink
[code]....
View 2 Replies
View Related
Feb 15, 2011
I have configured the "ISP" part of the VDSL as i am a tech for the ISP that has access to this, but i am not able to get my 887V to synch is there something i am doing wrong within the Cisco, i have included a debug and couple more things. [Code] ....
View 3 Replies
View Related
Nov 25, 2011
I'm trying to get an internet connection through my cisco 877va but I can't get access. I can see DSL up, however, the dialer0 interface can't get access to internet. Here is my configuration:
[code].....
View 2 Replies
View Related
Jun 17, 2012
I'm facing an issue since 2 month now , no one is able to tell me what's going on. The line goes down suddently for 2 or 3 minutes and this happens everyday at the same range (~2 or 3 hours) of time . I don't have any scheduled task to cause this. ISP in his side has also made some tshoot but found nothing and is convinced that the problem is coming from our side :
Here is some log :
Cisco IOS Software, C880 Software (C880DATA-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
rtr-Id#show debugging
Generic IP:
IP packet errors debugging is on
IP NAT ERROR debugging is on
PPP:
[Code]...
View 3 Replies
View Related
Jun 9, 2013
We have an ASA 5505. 5505 comes with two default vlans 1&2 with each of them marked as inside & outside respectively.My query is , if i do not want to use vlans on 5505 and only want to use the Ethernet ports as pure physical layer 3 ports, is it possible?i.e. i want to assign a layer 3 ip address on eth0/0 and eth0/1 and make them as the inside & outside interfaces rather than vlans. is it possible to do away with vlans in 5505 & will it work otherwise?
View 3 Replies
View Related
Aug 24, 2012
Just got hold of my first 887va for my home, never configured a vdsl interface before and was just wondering if my setup looked good to someone whos done it a few times.
View 6 Replies
View Related
Sep 3, 2012
I have installed a CISCO v887 router in Amsterdam officeI established a VPN tunnel between AMS office and Edinburg office.
1. The VPN is up and running
2. I am unable to browse anything from LAN computers in Amsterdam office.
3. From LAN computers I can traceroute to yahoo.com but from browser I cant browse yahoo.com and web page hanged out in this situation (website found waiting for reply). But nothing comes over and LAN users are unable to use internet.
[code]...
View 11 Replies
View Related
Apr 7, 2011
I have a problem with my Cisco 887V VDSL-router. The router gets a ip-address with dhcp from my provider. That works fine. I also can ping from the router:
routerVdslTestNew#ping google.ch source vlan 1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 74.125.79.99, timeout is 2 seconds:
Packet sent with a source address of 10.10.10.1
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 48/48/52 ms
My problem: If I want to ping google from a computer in the VLAN1 the ping doesn't work.
C:UsersXXXXXX>ping 74.125.79.99
Ping wird ausgeführt für 74.125.79.99 mit 32 Bytes Daten:
Timeout.
View 3 Replies
View Related
Sep 19, 2011
I'm trying to upgrade the VDSL firmware on a 887VA. I've uploaded the file vdsl.bin-A2pv6C035d_d23j to the router. I understand this file has to be renamed with a .bin extension in order to be recognized after a reboot, but the attempts I have made have not worked. What must this file be renamed to in order to load the new firmware into the VDSL controller?
Here is the current firmware information. I've tried several of the obvious file names.
Firmware Source File Name (version)-------- ------ -------------------VDSL embedded VDSL_LINUX_DEV_01212008 (1)
Modem FW Version: 110331_1212-4.02L.03.A2pv6C032b.d23fModem PHY Version: A2pv6C032b.d23f
View 1 Replies
View Related
Mar 13, 2013
Trying to get my 887va setup for VDSL but can't get to anything on the net -
Controller VDSL 0vpdn enablevpdn-group 1
interface ethernet0
no ip address
[Code].....
View 6 Replies
View Related
Mar 26, 2012
I am trying to design a network for our block of 20 apartments. The WAN supplies Ultima at up to 40 mb/s and the takeup on LAN is anticipated to be modest. However I have been told that two residents operate non commercial web sites currently on stand alone adsl with ddns. The netgear router supplied by the ISP obviously has port forwarding but how do I differentiate for traffic on port 80?
View 1 Replies
View Related
Apr 28, 2013
what enhancements, fixes, etc are included in the Cisco 887VA VDSL firmware version A2pv6C035l.d23j, relased 29-MAR-2013.I can't seem to find any release notes with this firmware.We are using version A2pv6C035d.d23j firmware on around 150 887VA's on BT ADSL lines, and was looking for any improvements this version may offer.
View 1 Replies
View Related
May 2, 2011
I have been using a Linksys Wireless-G ADSL WAG200G, Annex-A Gateway Router and it has been fine, now my ISP have told me that they are modernising the network and will need a router capable of managing ADSL2/ VDSL connections, so will my router be able to do that or will I have to buy a new one? It has firmware 1.01.09?Edit: I see in the DSL Modulation menu which is set at present to "Multimode" I also have options to select ADSL2, ADSL2+, ADSL2 AnnexM, ADSL2+ AnnexM and ASDL2 AnnexL but I do not see any mention of "VDSL"
View 2 Replies
View Related
Feb 10, 2011
I'm just wondering if its possible to ping an IPv4 host using the IPv6 host assuming that the NAT64 has already been implemented?
[code]...
View 2 Replies
View Related
Jan 24, 2013
I have a Dell Aspire 5332 laptop and i haven't used it since November 2012 (where it was working fine).It had Windows updates when i switched it off. I switched it on today and i have no internet connection. When hovering over the icon it says unidentified network - no internet access. My service provider is British Telecom and i am on the Fibre Optic package. I am using the BT Home Hub 2.0.Fibre Type B and also a Echolife HG 612 model FTCC VDSL NTE Router. I have Norton installed on the machine but there is only 1 day left on the subscription. I have tried a wired connection from the router but still have the same message. 2 other computers are wired to the router and all of our Ipads and Macbook connect wirelessly with no problems.
View 19 Replies
View Related
Aug 23, 2011
My Motorola SBG901 Modem/Router combo has stopped connecting to the internet. I have done all the troubleshooting with Comcast and with Motorola and it is out of warranty, so I will have to purchase a new one.In the mean time, I wanted to use it only as a wireless router connected to my Scientific Atlanta DPC2100R2 modem. Is there anyway to do this? Is there a way to disable the modem in the SBG901? Simply connecting with the ethernet cords has not worked. I connected the DPC2100 to the SBG901 via ethernet cord. My computer was able to pick up a wireless connection but there is no cable connection.
View 1 Replies
View Related
Jan 16, 2013
I want to connect my tata photon device to my bsnl wifi modem via a usb portavailable on the bsnl modem. This is to provide a wifi network that i can use to surf the net on my phone.
View 4 Replies
View Related
