Is there a way to find in a remote branch the adsl line number in a cisco router 886VA.
When giving show controllers vdsl 0
we can see the upload/download speed but there is no information about the line number. We need this information in order to troubleshoot adsl line problems with our ISP's in remote branch offices.
i have a problem with my adsl line connected on a HWIC-ADSL on router 2901 it was working good until yesterday the atm interface is down but the interface dialer is up .i connected this line into home adsl modem and the line is working good?
View 2 Replies View RelatedWe have a fairly major problem with some of our Cisco 877 units (5 in all). All are running 15.2(2)T2 in order to make use of zone-based firewalls and virtual reassembly, and all are exhibiting the same problem. When our ADSL line drops this si shown in syslog
2010-11-09 01:03:06 Local7.Info 192.168.7.1 4733: Nov 9 01:03:05.707: %FW-6-DROP_PKT: Dropping tcp session 192.168.7.2:25 109.224.142.52:41799 on zone-pair OutsideToInside class cm-MainServerServices due to RST inside current window with ip ident 02010-11-09 01:04:06 Local7.Info 192.168.7.1 4734: Nov 9 01:04:05.946: %FW-6-DROP_PKT: Dropping tcp session 192.168.7.2:25 109.224.142.52:41809 on zone-pair OutsideToInside class cm-MainServerServices due to RST inside current window with ip ident
[code]...
The "no retrain. sleep 20 seconds" messages continue forever more until somebody power-cycles the router - which is a bit inconvenient as two are 300 miles away. Surprisingly, our event manager applet isn't triggering the reload either, which defeats the object.
I have a pbx avaya phone system with lines and extension number.I needed a phone with line and extension.So i run the ethernet cable to the office made all connection and connected ethernet wire directly to the pbx avaya, and i got the phone working with the extension.But my question is to get the line working and the extension i have to punch down the cable from the pbx, the ethernet wire and the pair of wire coming in with the line?
View 7 Replies View RelatedADSL line do not activate. Telco Confirmed Like is Okay . They have tested no issue observed. Router replaced but did not work. Supspecting Firmware not compatible with telco . Not sure how to confirm on this.
sh ver
Cisco IOS Software, C180X Software (C180X-ADVIPSERVICESK9-M), Version 12.4(4)XC7, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Tue 31-Jul-07 20:24 by alnguyen
ROM: System Bootstrap, Version 12.3(8r)YH8, RELEASE SOFTWARE (fc2)
XXXXXXXXXXXXXXXXXXXXXXX uptime is 30 minutes
System returned to ROM by reload at 18:48:26 UTC Wed Oct 10 2012
System image file is "flash:c180x-advipservicesk9-mz.124-4.XC7.bin"(code)
Site A, site B, site C, site D is connected using leased line each other. We are using Cisco 1800, 2800 and 2900. Each site also have Internet connection using ADSL connected to firewall, we are using pix 501 and ASA 5510.My question is, can i use the existing ADSL line to be use as a backup line if the leased line is down on any of the site??
And i want it to trigger itself, once the leased line is down, the firewall UP the backup line? something like that..
I have D-link 2640U ADSL2+ modem. Now I have 12Mbps / 1Mbps internet connection. I am planning to move to 24Mbps /1Mbps intenet connection and I want to know if this modem is enough. What is the best modem so I get the full 24Mbps[CODE]
View 7 Replies View RelatedI do have a question, is WIC-1SHDSL-V3 able to support ADSL line?
We have WIC-1SHDSL-V3 module used for SDSL line, due to few site need to bring up with ADSL line with 1841 model, but HWIC-1ADSL module already EOS. The replacement model EHWIC-VA-DSL-A is not compatible to 1841. My architect suggest Symmetric Module like WIC-1SHDSL-V3 could be able to tweak the config to support Asymmetric purpose. I did google but do not found such related topic. Can any expert on this area to advice me?
Our church has 1 phone line, we run BTBusiness Broadband at one of the building where we have a couple of charities based. We have the phone line connected to an extension at the other end (where the Church is) >80m away. Any way of running a second concurrent router on the extension so I can set up an office with a VOIP number, pC's printers etc there too? We use Devolo ethernet over mains and wireless for the main building, but the church itself is on a completely seperate mains power supply so I can't use that. I could run 100m Cat 5 and locate a switch on that, but any way of achieving something similar over the phone cable which is already in place.
View 2 Replies View RelatedCan I install 2 ADSL routers on one telephone line with SKY. If I can does this mean that if sky give me 20mb connection, I can get two lots of 20mb using the two routers.
View 2 Replies View RelatedI have a broadband router (Linksys E1000) which I've flashed with a DD-WRT firmware. After doing so I realized that this router doesn't have an interface for ADSL port(RJ-11). How can I use the Linksys E1000 for my home network?
I've heard that I can use ADSL modem(not a router) & plug the RJ-11 to it & take from it the Ethernet & plug it back to the E1000(in the WAN port) would that mean that I can get just a modem and not a hybrid?
Note: Also, I have to mention that my ISP is using PPPoA & DD-WRT is not supporting it, but i googled & they said that the ADSL modem cab be the rescue. Can I pick any ADSL modem for this specific scenario or am I looking at a specific model?
Secondly, can I use my old router to do the job instead of buying a new ADSL modem ? & is it a good approach ? or should i buy a new ADSL modem ?
Update i turned my DD-WRT router(E1000) to act as access point, since this is the only way that i can use it with the DD-WRT feature. & i think this is better than have nothing :) I can now have the DD-WRT functions ;)
I have ADSL router Linksys X3000, but I have an issue with it. I have configured it properly (based on internet provider's manual), repeatedly checked it, but router still says that ADSL line is down. I have also another router from Zyxel and it works perfect with same wire and configuration, so I guess the line is fine.
PPP generic driver version 2.4.2 79 PPP Deflate Compression module registered 88 PPP BSD Compression module registered 84 PPPoL2TP kernel driver, V1.0 75 ccp_autowan_sm_thread=> Starts in Unconfigured mode, detecting state! 125 ->
[Code]....
Site A, site B, site C, site D is connected using leased line each other. We are using Cisco 1800, 2800 and 2900. Each site also have Internet connection using ADSL connected to firewall, we are using pix 501 and ASA 5510.My question is, can i use the existing ADSL line to be use as a backup line if the leased line is down on any of the site??And i want it to trigger itself, once the leased line is down, the firewall UP the backup line? something like that..
View 1 Replies View RelatedThe SRP547W supports creating both Wifi Voice and Data vlans.Can I configure a Wifi IP Phone to connect to the SRP547W Voice Wifi Vlan and have the SRP associate it with Line 1 (in lieu of a standard phone connected to the Line 1 FXO port - without additional hardware)?
View 1 Replies View RelatedIs the ADSL line interface on Cisco 877W not initialising a known issue? This interface on my router has been in this state for more than one month, with the rest of the router seemingly operational. The interface was connected directly to my ADSL broadband and worked well for two years. But then, about a month ago, the interface went down. I saw the exact moment this happened recorded as a syslog message. The only information was that the interface status had changed to down.
Initially I thought this was a matter of reload the router and all will be well. Did not happen. Then I thought my broadband connection was to blame. However, this option was quickly ruled out. So I went on to exhaust all troubleshooting options, including reflashing the router with the saved image and totally changing the configuration. Still no change. I have had to go back to my old BT home hub for internet access. In terms of speed this actually works a lot better than the Cisco router. But I would still rather have the router connected to my broadband line. What can I do to bring the ADSL interface back to life?
On my old router I could access the line stats on the home page giving me Attenuation and SNR margin, this allowed me to keep an eye on line quality, there seems to be no equivalent info on the X2000. Is this on a hidden page like the advanced wireless page.
View 1 Replies View RelatedRegion : Argentina
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP :
Region : UnitedKingdom
Model : TL-WR702N
Hardware Version : V1
Firmware Version : ?
ISP : Manx net
Within a property without an available adsl line I'm simply trying to network a wireless laptop with a wireless printer. Both devices recognise the router, etc, but problem sending file for printing to the printer. (laptop does not detect printer). Is the lack of an internet connection the issue or simply a configuration issue?
We have a remote site connected to ADSL line with a Cisco 887VA router attached. This has been working fine for the last couple of months. However, recently, the site have started to complain of performance issues (network slow, applications disconnecting, etc)Looking on the router, we can see evidence of packet loss/timeouts from a simple ping to the internet e.g. [code]
However, we have logged the fault with our service provider and they return all line tests as clear but what is particularly strange is that they also report “and the SNR Margins are well within threshold levels (Upstream 11.5 and Downstream 15.0)” which, unless I’m misunderstanding something, seems to be completely different from what the router itself is reporting.Is there a reason why the service provider’s stats for Noise Margin would appear to be so different from what the router is reporting?
I've moved a Cisco 887 router from a site where it was used to dial up on an ADSL line to a new site where we have a EFM circuit which terminates at a Cisco 1841 router managed by our ISP. I therefore need to re-configure our 887 router to work as a conduit from our servers back to the Cisco 1841 as its gateway.
I have asked from our ISP and they told me that i need to configure the 887 to use IP address 176.35.140.65 255.255.255.248 and its gateway should be 176.35.140.70. That's great advice in theory but I don't know how to configure this correctly
Our internal network is using subnet 192.168.42.XX which will need to be retained for local devices.
I can connect to my router but not to Internet, it seams that ADSL line "disconnects" my LAN/WLAN this issue is with Inalambrico 6867R router an other router, TP-Link is working great
View 1 Replies View RelatedI have bought a WAG320 & ever since I've had it the ADSL line keeps dropping every few hours. The LAN network is fine & I have 7 computers connected to the router wirelessly. When I press the re-set button on the back of the router everything is fine for a few hours then it starts doing it again?
View 9 Replies View RelatedCan't find my wep id number
View 1 Replies View RelatedHow to know port number of any URL, for example what is port number used by google.
View 19 Replies View Relatedwhat is a network ID number and how do i find it?
View 4 Replies View RelatedI am trying to set up a Linksys WAP4410N on our network. We are trying to run it using unrestricted access, but it is requiring a pin number. The prompt I get when trying to connect to the WAP is that the number should be in the original documentation. I can not find the original documentation and I cannot log into the WAP to find the PIN number.
View 1 Replies View RelatedWe are running WCS 4.2 on linux. I need to find the serial number of the software so I can raise a TAC case. how to find the serial number? I cant see it via the GUI.
View 10 Replies View RelatedHow to do the above thing.
View 3 Replies View RelatedHow to find out mobile number network
View 1 Replies View RelatedHow to find the mobile number from Name and address of the person.
View 8 Replies View Relatedi just need to know how to find my wep number on my computer cant seem to find it
View 3 Replies View RelatedI cant find the maximum number of vrf supported on a 3925E ?
View 1 Replies View RelatedHow can I find the serial number at Cisco PIX-515E ?
View 2 Replies View RelatedI have a number of Cisco 1801 routers connected to BT UK’s ADSL2+ Annex-A Wholesale Broadband Connect [WBC] services. The routers are experiencing connectivity issues. There is a cisco product bulletin that defines v4.0.0.18 as the version of ADSL Firmware required on the Cisco 1801 when connecting to this BT service.I would like to upgrade the ADSL Firmware for these routers but I cannot find v4.0.0.18 for the Cisco 1801 on CCO. All the 4.0.0.18 downloads appear to be for various flavours of 800. The Cisco product bulletin shows the 1801 as having the same chipset as the 857,867,877 and 887. Can I use the Firmware from one these 800 models? The MD5 Hash for the code suggests all of the these 800 model use the same code?
View 12 Replies View Related