Can Pure IPv6 Host Ping A IPv4 Host?
Feb 10, 2011I'm just wondering if its possible to ping an IPv4 host using the IPv6 host assuming that the NAT64 has already been implemented?
[code]...
ADVERTISEMENT
Can't Ping / Connect Ipv6 Host On Windows 7 Vs XP
Apr 27, 2011When I try to ping ipv6.xsnews.nl on either of my Windows 7 computers, it returns "Ping request could not find host". But when I do it on XP, it succeeds. I have tried putting the W7 PC in the DMZ, disabling the software firewall but it doesn't work.
What I think it involves is having ipv6 installed on each. I tried to duplicate the setup of both the XP and a W7 computer, installing the gogo6 tunnel. But apparently it's not setup on this computer because the ping result is the same as on the third computer which hasn't had ipv6 installed. s not setup on this computer because the ping result is the same as on the third computer which hasn
Cisco VPN :: Pix 515e - Remote Host Cannot Ping Any LAN Host
Jun 27, 2011I have a host that can successfully connect to a PIX 515E (7.x OS) via VPN Client; however, I have no IP routing to the LAN from the remote host.The VPN IP pool works finem,The LAN default gateway is the inside interface on the PIX; the network is flat L2 behind it.The default route on the PIX points out; no other routes are defined,The VPN remote host can be pinged from LAN hosts, but the VPN remote host cannot ping any LAN host, not even the PIX inside interface.
View 2 Replies View RelatedCisco VPN :: ASA 5510 Ping / Communication Host To Host
May 7, 2012ASA 5510
Ver 8.2(5)
I have been looking all over the place for the answer of how to allow clients on an IPSEC VPN to ping from host to host.
Cisco Switching/Routing :: Can Ping From R1 To R3 SVI4 Gateway But Cannot Ping Host
Dec 12, 2011I set this up and I can ping all the gateways but never the hosts. I was hoping I could make these links between 6500's a mix of L2 and L3. Check it out. They are connected in a linear fashion R1--->R2--->R3. I can ping from R1 to R3's SVI4 gateway but I can never ping a host on that SVI4. I was hoping that I could use the port-channels between 6500's as routed links or as trunk links depending on the type of traffic....thought it would ease the migration. I suppose I could always get rid of the port-channels and just make separate L2 and L3 links between the 6500's.
View 3 Replies View RelatedPing From Host To Guest With NAT?
Jun 27, 2012I have installed an Oracle DB (11.2) on a guest VM (Centos 5) and my host is Windows 7 Ultimate.I need to able to connect to the DB from windows.Ping status is as follows:
guest -> host - IP : Yes
guest -> host - hostname : Yes
guest -> guest - hostname : Yes
guest -> guest - IP : Yes
[code]....
Cisco WAN :: 871 Can't Ping From Host
Jun 30, 2012I'm going through the CCNA training and I'm setting up my DHCP server on my 871 router. I have my cable modem into the WAN port on my router and have 1 host plugged directly into Fastethernet 1. I can ping any IP I want from the IOS prompt but I only have local access from the host. [code]
View 4 Replies View RelatedCisco :: Can't Ping From Outside To The (online Host) PC
Aug 26, 2012I tried to ping from the "online host" PC to the outside,it succeeded. However, I can't ping from outside to the "online host" PC.
View 2 Replies View RelatedCisco :: Can't Ping From ASA To Host In GNS3
Apr 24, 2012I test all devices using ping command, from ASA to router was fine (on both interface) but not to Host , and host to router was fine, but only on directly interface(F1/0), and to ASA was not success. am i miss something in my configuration?
View 5 Replies View RelatedCisco :: Can't Ping From Inside To Outside Host?
Jul 6, 2011configure my Cisco ASA5510 (asa version 8.3.1) so that one of the host (e.g.192.168.8.20) behind management interface can ping to the other host (e.g. 192.168.2.246) behind OUTSIDEinterface. I tried modifying the ACLs, NATs and ICMP statement, but still failed[CODE]
View 19 Replies View RelatedCisco WAN :: Cannot Get ASR 1002 To Ping On Interface To Host
May 12, 2013I have a cisco ASR 1002 I have plugged a host into an addressed port and the port comes up however the host cannot ping the router and the router cannot ping the host. Neither can router ping its self. I do the same on a cisco 2800 router and it works fine. What's goin on. Is it the fact that this is a ASR router ?
View 5 Replies View RelatedCisco :: 1140 APs - No Ping To Host From Local LAN
Apr 3, 2013I'm using 3 AP's 1140 with local authentication using local radius (flex connect mode).the radius server im using is MS 2008 R2.authentication is working great on all devices pc's&mobile.authentication method is PEAP wpa2 aes enterprise.after 3 or 4 hours devices loose connectivity to the web.the device seems to be still connected to the ap but there is no ping to host from local lan or any arp learnd on local router.only manual disconnect on device and reconnecting brings connectivity up again.in one case only reseting the AP's worked.
View 6 Replies View RelatedPing Could Not Find Host / DNS And Key-port / Server Not Found
Apr 30, 2011recently I had some malware on my Windows XP Professional (version 2002), so I followed a guide at Bleeping Computer [URL] to get rid of it. Problem is, for some reason, after I finished, I could no longer access the internet!When I try, FIrefox gives me their "could not connect" message: "Server not found. Firefox can't find the server at [site]." Check the address for typing errors such as ww.example.com instead of [URL]"When I try to log into MSN, the troubleshoot says I have a problem with my DNS and Key Ports.I'm not good with computers so I Google'd and found some ping-ing instructions. When I tried to ping [site], I get: "Ping request could not find host [site]. check the name and try again." This happens regardless of the site I use.Lastly, I tried "ping 127.0.0.1" from a troubleshooting site. It gives me: "Pinging 127.0.0.1 with 32 bytes of data:
Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
[code]..
Cisco Firewall :: ASA5505 - Can't Ping Inside Host
Sep 29, 2012I just try to ping a internal Host but it want to go.
Laptop<===>ASA5505
Connected is the Laptop at Ethernet 0/2 Inside
My running-config is a clear config, only VLAN 1 has a IP and Ethernet 0/2 is up.
But If I try to ping to the Laptop I get the followed:
asa5505# ping 192.168.1.100
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.100, timeout is 2 seconds:
?????
Success rate is 0 percent (0/5)
asa5505#
From the Laptop to the ASA5505 I can Ping successfully.
Cisco Firewall :: ASA5505 Cannot Ping Inside Host
Aug 2, 2011I have Cisco ASA 5505 installed and use as default gateway. I go to Internet through the ASA5505 Here is my Problem.I can not ping from ASA prompt(ASA#) to my Laptop connected to the ASA, but i can ping the ASA inside interface from laptop i can not use ASDM and the VPN Tunnel is not working between the sie
ASA# ping 10.10.10.12
???????????
100% lost
Laptop c
C:/ping 10.10.10.1
!!!!!!!!!!!!!!!!
Here is the Topology
INTERNET .<=========================>ASA<===============================> LAPTOP
I disabled window firewall on the Laptop , but no goof result.
Cisco Application :: 11503 Ping For One Virtual Host
Apr 27, 2013I have a single cisco 11503 load balancer.There is a single Banner student information system which is load balanced on it with Virtual ip 10.3.20.101 which is working fine without any issues .I am now trying to add an Oracle ERP application with virtual IP 10.3.20.230 and physical ips 10.3.19.22 and 10.3.19.23 all on port 8003.When I just make the group ERP-Apps-Grp active , the vitual ip address 10.3.20.230 is pingable , but when I make the the content Erp_IAT active it stops pinging. [code]
View 6 Replies View RelatedCisco Firewall :: ASA 5520 - PING From Outside Into Inside Host
May 13, 2013I have ASA 5520. I cannot ping the host(192.168.1.20) which is inside firewall from outside hosts. Inside host (192.168.1.20) is translated into (198.24.210.226) using static NAT.From outside host, I used "PING 198.24.210.226". Is it because I used dynamic PAT for inside hosts?
interface GigabitEthernet0/0nameif outsidesecurity-level 0ip address 198.24.210.230 255.255.255.248!interface GigabitEthernet0/1nameif insidesecurity-level 100ip address 192.168.1.1 255.255.255.0
[Code].....
Routers / Switches :: Ping 10.0.0.1 -t Give Destination Host Unreachable?
Mar 17, 2013ping 10.0.0.1 -t give me destination host unreachable in the same time when i wright ping 192.168.1.1 -t it give me the correct reply but the net doesnt work
View 3 Replies View RelatedPing - Destination Host Unreachable And Time To Live Exceeded
Oct 17, 2011when do we get Desteination host Unreachable and time to live exceeded while trying to ping .
From 10.1.1.1 icmp_seq=2 Destination Host Unreachable
From 10.1.1.1 icmp_seq=4 Destination Host Unreachable
From 10.1.1.1 icmp_seq=7 Destination Host Unreachable
Linksys Wireless Router :: WRT54G Unreachable Host And No Ping
Sep 26, 2011I've tried everything that has been posted so far except for opening up the router itself which I will refuse to do.- Getting = Host Unreachable 192.168.1.20 (I am using 192.168.1.1 as the gateway)- No ping whatsoever even when turning on the router over and over.
View 2 Replies View RelatedCisco Firewall :: NAT ASA 9.0(2) / Cannot Access Original IP Using Another Port Or Ping From Host
Apr 10, 2013Basically after upgrade from ASA 8.4 to 9.0 (2) I have problems when certain types of NAT.Example:SA 8.4: nat (LAN, outside) 85 10.252.253.123 source static 192.168.3.2 192.168.3.2 192.168.3.104 static destination service http http In this form the host 192.168.3.2 uses the mapped ip (192.168.3.104) to access by http while other ports can be accessed using the original IP (10.252.253.123).
ASA 9.0: nat (LAN, outside) 85 10.252.253.123 source static 192.168.3.2 192.168.3.2 192.168.3.104 static destination service http http In this form the host 192.168.3.2 uses the mapped ip (192.168.3.104) to access by http but unlike before now I cannot access to the original IP (10.252.253.123) using another port or ping from host 192.168.3.2.
Cisco WAN :: 1941w AP Can't Ping 2nd Router / Host But Interface Reachable
Feb 2, 2013From the router I can ping the 2nd router, all its host and all of the 1941w interfaces.
From the 1941w AP i cannot reach the 2nd router or any of its host, but I can reach the interface that is connected to the 2nd router but only one side of it.
Attached are both my router and ap configs. At the moment I am just trying to reach the 2nd router and its host so I can update the AP IOS image but cannot reach the tftp server.
Cisco VPN :: 2611xm - Unable To Ping Remote Host Through Tunnel?
Apr 20, 2012I am in a test environment using an ASA 55005 and a Cisoc 2611xm router. ASA is running version 8.4 and router is running is ios12.4. My VPN tunnel comes up but I am unable to ping between remote hosts. I used the ASDM and SDM for the configuration. Attached is a copy of both configs.
View 8 Replies View RelatedServers :: Ping Locally / Reply Successful - Destination Host Unreachable
Mar 4, 2011I am using the window server 2008 and configure tcp/ip properties correct ping locally reply successful when ping localy but when ping yahoo.com then reply destination host unreachable whereas gateway and dns ip is also correct configure so tell me solution about this problem because i am useing the internet.
View 1 Replies View RelatedCisco Firewall :: Unable To Ping Host From Inside Interface From PIX525
Feb 3, 2012When I tried to upgrading PIX525 6.3 to 7.0 , Not able to Ping the host from the PIX 525 Inside interface which is on the same subnet, Also from the host to Inside Interface , Tried with Directly connected laptop with Cross cable and using Straight cable via switch, But the results end with fail.
View 2 Replies View RelatedDNS Not Working IPV4 IPV6 Not Connected?
Jan 11, 2013has quite frankly gotten me absolutely annoyed . I've tried just about everything, from using the netsh commands to changing the dns to 8.8.8.8 or that other one or the other. Nothing is working, I unplugged the router, problem persists, I disabled IPV6 problem persists, I restore, problem persists. The only clue I have is my router, and mysteriously, there are TWO of my computer on it. It might be nothing but most certainly has caught my attention. Also, it gives me this info about my media being disconnected
View 14 Replies View RelatedBroadband :: IPv4 / IPv6 - No Internet Access
May 17, 2011I am using window 7 on my laptop. I am using broadband internet (not wireless etc) via my external lan card but IPv4: IPv6: No Internet access shows.
View 4 Replies View RelatedNo Internet - Limited IPv4 And IPv6 Connection?
Aug 10, 2011I have a dell inspiron 15 and I've been having trouble fully connecting to my wireless internet. It says I have signal but gets stuck on identifying the network and I have limited IPv4 and IPv6 connectivity.
Here's the ipconfig if you can identify the issue with it:
Windows IP Configuration
Host Name . . . . . . . . . . . . : M-PC
Primary Dns Suffix . . . . . . . :
[Code].....
Cisco Security :: ACL Ipv4 And Ipv6 On Same Line Vty?
May 2, 2012I've just want to confirm if I can protect a router (telnet and ssh) putting 2 ACL's (one IPv4 and other IPv6) on the same line vty. Something like:
line vty 0 4
access-class hostsIPv4 in
ipv6 access-class hostsIPv6 in
Do I have to use named ACLs?
Routers / Switches :: IPV6 Implementation In IPV4 Network
Jul 1, 2012our company backbone is hp 5406, and desktop switches are hp 2510 currently we are working with ipv4.if we want to start use IPV6 for test environment, what’s things we need to enable in our backbone/regular switches.i mean for example if we want to set static IPV6 address for 2 servers and send ping between them, or even make new vlan with IVP6 subnet, and use it like regular vlan but with static ip's(until we got ipv6 dhcp).i have hp 5406 manual for IPV6 but i can't understand what i really need to do for start using IPV6.
View 5 Replies View RelatedD-Link DIR-615 :: Setup IPv6 In IPv4 Tunnel With Tunnerbroker Service
Mar 24, 2013Recently I wanted to setup IPv6 for my home network. I signed up for tunnelbroker.net service and was provided with IPs. Then I configured the IP address in my DIR-615. But It's not working..
Screenshot of IPv6 config (router) : Screenshot of my Win 8 network Config : I also tested at [URL] but failed...
D-Link DIR-825 :: IpV4 Versus IpV6 Implementation For Remote Access And VPN?
May 16, 2013I currently have ipV4 as the setting on my DIR-825. Other posts seem to want ipV6 which is more secure but is not possible with a DIR-825 Rev A1. I have two routers, a primary router (DIR-825 Rev B1) capable of ipV6 and a secondary router (DIR-825 Rev A1). If I implement ipV6 on the Rev B1 router but keep ipV4 on the secondary router, will this improve the security, or will it just mess things up so nothing works?Certain devices (cell phones and most Tablets) don't deal with ipV6 very well at all. The ones I have tested flat don't connect to the wireless network if the router is set at ipV6. Is ipV4 adequate for a Home/Small Business Network when trying to implement Remote Access and VPN?
View 2 Replies View RelatedCisco Firewall :: 5520 - Static Mapping On ASA From IPv6 To IPv4
Dec 7, 2011ASA 5520 running 8.2
Is it possible to do static (inside,outside) with the outside address being IPv6 and the inside IPv4?
If yes, is it possible to do this in parallel with an existing static mapping that goes IPv4 to IPv4?