I've just want to confirm if I can protect a router (telnet and ssh) putting 2 ACL's (one IPv4 and other IPv6) on the same line vty. Something like:
line vty 0 4
access-class hostsIPv4 in
ipv6 access-class hostsIPv6 in
Do I have to use named ACLs?
has quite frankly gotten me absolutely annoyed . I've tried just about everything, from using the netsh commands to changing the dns to 8.8.8.8 or that other one or the other. Nothing is working, I unplugged the router, problem persists, I disabled IPV6 problem persists, I restore, problem persists. The only clue I have is my router, and mysteriously, there are TWO of my computer on it. It might be nothing but most certainly has caught my attention. Also, it gives me this info about my media being disconnected
View 14 Replies View RelatedI am using window 7 on my laptop. I am using broadband internet (not wireless etc) via my external lan card but IPv4: IPv6: No Internet access shows.
View 4 Replies View RelatedI have a dell inspiron 15 and I've been having trouble fully connecting to my wireless internet. It says I have signal but gets stuck on identifying the network and I have limited IPv4 and IPv6 connectivity.
Here's the ipconfig if you can identify the issue with it:
Windows IP Configuration
Host Name . . . . . . . . . . . . : M-PC
Primary Dns Suffix . . . . . . . :
[Code].....
our company backbone is hp 5406, and desktop switches are hp 2510 currently we are working with ipv4.if we want to start use IPV6 for test environment, what’s things we need to enable in our backbone/regular switches.i mean for example if we want to set static IPV6 address for 2 servers and send ping between them, or even make new vlan with IVP6 subnet, and use it like regular vlan but with static ip's(until we got ipv6 dhcp).i have hp 5406 manual for IPV6 but i can't understand what i really need to do for start using IPV6.
View 5 Replies View RelatedASA 5520 running 8.2
Is it possible to do static (inside,outside) with the outside address being IPv6 and the inside IPv4?
If yes, is it possible to do this in parallel with an existing static mapping that goes IPv4 to IPv4?
Would like to learn from you what tools I could use in a Network that provides IPv6 visibility and also completely blocks IPv6 from being tunneled through ipv4 only networks.
I have tested this from Linux running some internal penetration test apps,but specifically running Teredo tunneling in Local LAN that is able to completely bypass security paremeters such as websence filtering servers and be able to accessing internet IPv6 sites, even its equivalent IPv6 address based on its IPv4 PAT address could be pinged from outside.. is like the PIX firewall never existed - wide opened door .
Blocking in outbound and inbound direction udp ports 3545 and 3544 seem to done the trick in dropping IPv6 at the PIX/ASA from being tunneled out or in.. Is this so ? Realy ? not to fast!! None of our local systems - users PCs or servers have IPv6 stack enabled as a policy, however, in reality this poses a serious thread.
For example, Teredo tunneling running in a host inside LAN say by a user who is a hacker can use different UDP ports from the standard listening udp 3545/3544 ports, host will still be able to tunnel IPv6 through IPv4 again, in this case I want to have tool or a strategy that can detect this internally beside being blocked at the firewall, I am looking at AIP for our ASAs would this help? What other tools could I utilized to have some sort of IPv6 awareness in our LAN without having to rung IPv6 that can provide some visibility of this invisible traffic in IPv4 LANs.
Recently I wanted to setup IPv6 for my home network. I signed up for tunnelbroker.net service and was provided with IPs. Then I configured the IP address in my DIR-615. But It's not working..
Screenshot of IPv6 config (router) : Screenshot of my Win 8 network Config : I also tested at [URL] but failed...
I currently have ipV4 as the setting on my DIR-825. Other posts seem to want ipV6 which is more secure but is not possible with a DIR-825 Rev A1. I have two routers, a primary router (DIR-825 Rev B1) capable of ipV6 and a secondary router (DIR-825 Rev A1). If I implement ipV6 on the Rev B1 router but keep ipV4 on the secondary router, will this improve the security, or will it just mess things up so nothing works?Certain devices (cell phones and most Tablets) don't deal with ipV6 very well at all. The ones I have tested flat don't connect to the wireless network if the router is set at ipV6. Is ipV4 adequate for a Home/Small Business Network when trying to implement Remote Access and VPN?
View 2 Replies View RelatedI have a Dlink DIR-825 B1 with firmware 2.05NA. I recently reset it to factory defaults to make sure I didn't misconfigure something.
I have been struggling to get a IPv6 in IPv4 tunnel working with tunnelbroker.net. I think the issue is a problem with the router itself and i'm not sure how to get it fixed.
All of my machines were getting IPv6 addresses (both windows, mac, linux) but none of them seemed to work. All I was able to do was ping the gateway itself using the local lan address. In each case they were missing a default IPv6 route. If I added a default route then it would work.
I started looking at the packets using a network sniffer and the Router Advertisements all had a Router lifetime value of "0" which is RFC4816 speak for "don't use this router as the default router". So Windows/Linux is exactly right by not setting a default route.
The strange thing was that when I reboot the router I would briefly get a router advertisement with a lifetime of 1800s, the corrert prefix and dns server but then another router advertisement would come along 5 seconds later with a router advertisement of 0.
I have TCP' Other observations
... using 6to4 I would get working IPv6 address. The difference again seemed to be the Router Lifetime. But I want to use a permanent tunnel. I have found 6to4 unreliable.
... the router never responds to router solicitations. It only sends a router advertisement when it wants to.
... the router never responds to DHCPv6 when that is configured.
i got trouble for this ipv4 & ipv6 fragment trafic prob/attack.how do i prevent it from comming in to my network? is it way to prevent it in cisco router part?
View 2 Replies View RelatedI'm working on a computer that has no connectivity on wired or wireless connections. the wired eth card is a broadcom netlink card and the wireless adapter is an atheros ar5007eg. I found the drivers for the wireless on acer.com and removed the driver that was on here at first and put the one from acer. i cant find a network in range but device manager says its working fine. Then I found out the wired connection isnt working either and im getting the same messages from windows troubleshooter. It says both are "experiencing driver or hardware related issues and "make sure your internet protocol bindings are correct - ensure that ipv4 and ipv6 are selected in the config for the network adapter". it links me to the connection properties and ipv4 and ipv6 are checked off for both. futhermore, in the connection status window it says i have no ipv4 or ipv6 connectivity.
View 6 Replies View RelatedNo changes made but router will lose all information for IPv connectivity. I have paid twice to support to fix this issue and it still occurs every few months. I tried rebooting router, and doing an IP Release/ Renew and router does not get IP address.
View 4 Replies View RelatedI have a virtual machine running in my desktop which connected on the gigabit lan port on EA4500 with firmware 2.0.37.What I want to be able to do forward a port that came from an external ipv4 address to the ipv6 address and a different port to my virtual machine (to remote desktop port 3389).The reason I want to convert the traffic to ipv6 is because virtual machine is running vpn and is not reacheable through ipv4 (unless bunch of routes are setup and things get complicated etc). I verified my phsical server and virtual server get both ipv6 ip addresses through ipv6 tunnel from comcast. Without tunneling I could not get ipv6 setup using automatic mode with comcast, it simply did not work for some reason.
View 1 Replies View RelatedI'm just wondering if its possible to ping an IPv4 host using the IPv6 host assuming that the NAT64 has already been implemented?
[code]...
well a couple days of go it was working fine until i updated windows 7 now it says im connected to the internet but when i go on it dosnt load anything, and when i go check it says that "IPv6 connectivity: No Internet access" how ever the IPv4 is connected to the internet, should i restore settings to osmetimes earlier this week
View 2 Replies View RelatedMy laptop is not connecting to the internet, I know that it is not a router problem as my mine PC and Notebook are connecting with no issues.I have removed all router devices as had an new once once it was last working.I tried this morning to set it up again without success. I have compared to setting with my pc and have found the difference is with the IPV6 connectivity.
View 6 Replies View RelatedI configured a 1841 router that connects to a DSL modem. This DSL connection is our Internet connection for vendor and IT testing. I have connectivity to the Internet using nat and have configured the router to act as a DHCP server. It seems to be working fine. I just want to configure some best practices for securing the device from the outside access. Is there some standard best practices I should be configuring?
View 2 Replies View RelatedCisco 2500 series access servers show line usage with the "show line" command:
View 2 Replies View RelatedThe reason is i want to know the difference between the leased line and the DSL line. The whole thing behind the confusion is, We plan to have a high speed internet connection in our office. We will don't have a branch office or some thing like that. I preffered to have high speed internet in our office. I found in some website that Lease line will have high speed connectivity(Upto 10Gbps). Can i use the lease line or DSL is enough for our office. Our office contains of 82 user who will use internet.
View 2 Replies View RelatedI have a question about a netmask.How many netmask are there for IPV4?
View 5 Replies View RelatedI bought the SG300-10 Switch a few days ago and updated it to firmware 1.3.0.59, but i think there's a bug in this firmware. If I go to "IP Configuration" IPv4 Routes" in L3 Mode nothing is displayed. In the log file i see that:
21474773112013-Mar-16 09:51:34Error%HTTP_HTTPS-E-DIAGNOSTICS: ERROR - in <RL_vtLeadTableGet> tag, can not find the table rlInetRoutingDistanceTable in the MIB. 21474775182013-Mar-14 22:39:22Error%HTTP_HTTPS-E-DIAGNOSTICS: ERROR - in <RL_vtLeadTableGet> tag, can not find the table rlInetRoutingDistanceTable in the MIB., aggregated (1)
Reset of the Switch doesn't work.
I understand you can't assign an IPv4 Address to a "port". But here's my issue. I have two network cables attached to a managed switch, the location of the two cables are very important. Two computers attached to the said cables.I would like to communicate with one of the computers on PORT 1 and PORT 2, regardless of what computer is plugged into them. They get there IP's via DHCP, and a static IP wont work - as the computer plugged into PORT 1 or 2 may be different.So. I have two ports on the switch that I always want to communicate with the computer on the other end. But I don't (will not) always know the IP address of the computer(s) connected.
View 12 Replies View RelatedMicrosoft Windows [Version 6.1.7600]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersAlex>ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : Alex-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
[code]....
So I have been trouble shooting this for just over a day and still nothing, but anyways. My computer says that I am connected to the wireless router and that I have great signal strength but I have no internet access from either my IPv4 or IPv6. I have been using the cmd commands such as netsh reset, and the like. I have restarted both modem and router a few times as well as my computer. Also just did a recent avg scan and firewalls are all off. This is all coming from my mac laptop which is connected just fine which leaves me even more confused.
View 12 Replies View RelatedI have a Windows 7 computer. My boss changed the IPv4 address of this computer. Nowalthough all computers can connect to the network, they can no longer see this computer. And this computer cannot connect to the other computers.
View 1 Replies View RelatedI live in a shared house, and I am the only one who has been experiencing issues connecting to the internet. I have to ask a housemate to reset the server, as this is the only thing that works.
When I am unable to connect, and I use command ipconfig, the following appears: Autoconfiguration IPv4 169.254.23.29 On the occasions when I am connected, the following appears in its place: IPv4 IP Address: 192.168.0.2
One tip that I came across was to check the box (Wireless Network properties, Connection tab) for "Connect even if the network is not broadcasting". I had hoped this simple solution would assist, but to no avail.
Lenovo G550 with windows 7 shows that the Internet is connected but the IPv4 and IPv6 connectivity says no network access. I updated and reinstalled drivers, typed in some cmd command and restarted computer with no success. I also called tech support and they had me go into safe mode, the Internet didn't work there so he said it was a driver problem but wouldn't fix it.
View 6 Replies View RelatedWe set up three new terminals this week at the office; they're all running Win 7 Pro 32-bit. I set them all up simultaneously (literally sat at a desk and entered the same keystrokes at each of them), so I don't see any obvious reason that one is behaving differently from the other two. The essential problem is that the terminal doesn't see the Internet.
Here are all the particulars that I think might be interesting, listed in no particular order:
- The terminal ran fine for several hours. Email access, Internet access, from 9 a.m. to 2 p.m. At that point, the user called me to show me a dialog box. I used System Restore to go back in time to 9 a.m. in case the user had somehow managed to do anything (though she's not an admin).
- IPv6 is disabled.
- The workplace uses Static IPs. The IP address is entered correctly in the IPv4 properties (x.x.x.213), but at cmd / ipconfig, I get this result: "Autoconfiguration IPv4 address: 169.254.95.187"
- In Network and Sharing Center, the network (which is only known as Unidentified Network) is set to type Public. When I reset it to type Work and reboot, it resets to type Public.
my ipv4 show limited and my ipv6 also show limited when connect internet through wireless..yesteday can wep but show limited connectivity...
Windows IP Configuration
code...
I have Dell XPS L502X, Windows 7 Home Premium.My internet was working last night but when I turned it on this morning it would not connect.It is connected to my bt homehub with full strength but no internet access. It says IPV4 No Internet Access. I tried using a wire to connect it but that did not work either.Other devices are connecting. So can't be a problem with the internet itself. [code]
View 5 Replies View RelatedLast two weeks, I have had a problem connecting to public hotspots. My own WiFi network is fine, but while I am connected to any public hotspot I get the 'no internet access' message on the wifi symbol.While connected to my own network, ipconfig/all shows that I have an Autoconfiguration IPv4 address in the (correct) 192 range - but when connected to a hotspot, the address is in the 169 range, or occasionally (as in the instance below) in the 10 range. Clearly this is the problem, but I cannot figure out what has caused it. Is it hardware? Software? Malware? Or user error?I have run the Wireless Test and the log results are pasted below.
Windows IP Configuration
Host Name . . . . . . . . . . . . : XPS-CLIENT-TIM
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Broadcast
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
[code]....
A few months back, my computer stopped connecting to networks. Through some process or another, I ended up "fixing" it by manually inserting the ipv4 settings. Apparently that only allows it to connect to my router though, as public wi fi won't work for it. If I leave the ipv4 settings set to automatically obtain information, the computer won't connect to the network. It will stay on the "identifying network" part indefinitely. In addition, I can't connect through the modem directly either, manual settings or not.
Here is the ipconfig while ipv4 is in auto-obtain
Windows IP Configuration
Host Name . . . . . . . . . . . . : Home
Primary Dns Suffix . . . . . . . :
[Code].....