Can't Connect To Network Without Manual Ipv4 Settings
Jun 13, 2012
A few months back, my computer stopped connecting to networks. Through some process or another, I ended up "fixing" it by manually inserting the ipv4 settings. Apparently that only allows it to connect to my router though, as public wi fi won't work for it. If I leave the ipv4 settings set to automatically obtain information, the computer won't connect to the network. It will stay on the "identifying network" part indefinitely. In addition, I can't connect through the modem directly either, manual settings or not.
Here is the ipconfig while ipv4 is in auto-obtain
Windows IP Configuration
Host Name . . . . . . . . . . . . : Home
Primary Dns Suffix . . . . . . . :
[Code].....
View 14 Replies
ADVERTISEMENT
Mar 14, 2013
Region : Argentina
Model : TL-MR3220
Hardware Version : V2
Firmware Version :
Region : Others
I have MR3220 version 2 and HUAWEI E398 stick.It connects to 3G/4G network, but with wrong APN.It seems to me that manualy changed APN can not be applied. [code]
View 4 Replies
View Related
Jul 9, 2012
Do you know when will be possible to manual configure ipv6 settings? I have all parameters from my ISP but the settings on the router are only automatic and 6rd. Is it possible to enable this in future firmwares?
View 1 Replies
View Related
Jul 10, 2011
So I have been trouble shooting this for just over a day and still nothing, but anyways. My computer says that I am connected to the wireless router and that I have great signal strength but I have no internet access from either my IPv4 or IPv6. I have been using the cmd commands such as netsh reset, and the like. I have restarted both modem and router a few times as well as my computer. Also just did a recent avg scan and firewalls are all off. This is all coming from my mac laptop which is connected just fine which leaves me even more confused.
View 12 Replies
View Related
Jun 11, 2012
I have a new Dell Inspiron 14Z (purchased in February), it has been running great until recently, the internet connection (wireless) completely stopped working.When I try to connect through Internet Explorer, it says Internet Explorer cannot display the webpage. I Diagnose Connection Problems, and this is what I get:"Windows could not automatically detect this network's proxy settings." On Chrome, I got a long list of things to do (check DNS settings, LAN Network, etc. have tried every and all checked/unchecked box they advise.) This error shows up:Error 105 (net:: ERR_NAME_NOT_RESOLVED): The server could not be found. However, I accidentally uninstalled Chrome trying to fix this problem, so Internet Explorer is all I have.It's been about 2-3 weeks with no internet. Have tried connecting to 5+ different networks (Home- AT&T U-verse, University of Texas Network, restaurants, etc)tried restarting my computer, setting my LAN settings back to normal, and it still won't work. Other computers work on all of the networks I've tried, it's just mine that wont. [code]
View 13 Replies
View Related
Mar 16, 2012
We set up three new terminals this week at the office; they're all running Win 7 Pro 32-bit. I set them all up simultaneously (literally sat at a desk and entered the same keystrokes at each of them), so I don't see any obvious reason that one is behaving differently from the other two. The essential problem is that the terminal doesn't see the Internet.
Here are all the particulars that I think might be interesting, listed in no particular order:
- The terminal ran fine for several hours. Email access, Internet access, from 9 a.m. to 2 p.m. At that point, the user called me to show me a dialog box. I used System Restore to go back in time to 9 a.m. in case the user had somehow managed to do anything (though she's not an admin).
- IPv6 is disabled.
- The workplace uses Static IPs. The IP address is entered correctly in the IPv4 properties (x.x.x.213), but at cmd / ipconfig, I get this result: "Autoconfiguration IPv4 address: 169.254.95.187"
- In Network and Sharing Center, the network (which is only known as Unidentified Network) is set to type Public. When I reset it to type Work and reboot, it resets to type Public.
View 1 Replies
View Related
Jul 1, 2012
our company backbone is hp 5406, and desktop switches are hp 2510 currently we are working with ipv4.if we want to start use IPV6 for test environment, what’s things we need to enable in our backbone/regular switches.i mean for example if we want to set static IPV6 address for 2 servers and send ping between them, or even make new vlan with IVP6 subnet, and use it like regular vlan but with static ip's(until we got ipv6 dhcp).i have hp 5406 manual for IPV6 but i can't understand what i really need to do for start using IPV6.
View 5 Replies
View Related
Feb 8, 2013
Western digital wd livewire powerline av network kit manual?
View 1 Replies
View Related
Jun 6, 2012
My laptop have 2 NIC attach it, the cable NIC and Wireless NIC, the cable one connect to my lab network environment and the Wireless connect to office network environment (connect to internet) which both have differen segments [code] when my Wireless was turn off my pc can ping to all segment on my lab network environment, but if the wireless was turn on, i cant ping to others segment but only my laptop segment and i still could surfing to the internet without any problem.then i tried to add a new route from my laptop using "route add x.x.x.x mask x.x.x.x (gateway)" in command line and after that i can ping back to all segment in my lab network environment eventhough my wireless was onwhy i have to create a manual route into my laptop so that i can have connection between my laptop and my lab environment in the condition my wireless turn on ??
View 8 Replies
View Related
Aug 14, 2011
I'm working on a computer that has no connectivity on wired or wireless connections. the wired eth card is a broadcom netlink card and the wireless adapter is an atheros ar5007eg. I found the drivers for the wireless on acer.com and removed the driver that was on here at first and put the one from acer. i cant find a network in range but device manager says its working fine. Then I found out the wired connection isnt working either and im getting the same messages from windows troubleshooter. It says both are "experiencing driver or hardware related issues and "make sure your internet protocol bindings are correct - ensure that ipv4 and ipv6 are selected in the config for the network adapter". it links me to the connection properties and ipv4 and ipv6 are checked off for both. futhermore, in the connection status window it says i have no ipv4 or ipv6 connectivity.
View 6 Replies
View Related
Jun 16, 2013
I am using the Vostro 3360 with win 7, I did used the hotspot station software accomplish with the WiFi driver before and worked fine. However, the hotspot is not working as the ipv4 is showing 'no internet connect'. And my iPhone cannot connect it too.
View 1 Replies
View Related
Aug 4, 2012
I have had several Linksys and Cisco routers in the past, and I'm a network engineer. My E3000 died after only 18 months so I had to run down and buy a new router, thus the EA4500.
I use the manual way to configure all my network gear. Nothing on my network changed, except the router replacement.If I leave the router default address at the 192 range, DHCP will issue a IP address. However, I do not use that range and after cdhanging the range, setting my start IP address, etc, I save everything and even tried rebooting the router to no avail. The router will not issue a DHCP addrss if you change the default range.
I can manually configure my clients with a static IP and all is good, no issues at all. I just can't get DHCP to work. My E3000 was configured exactly the same way and worked just fine, well up until two days ago.I have tried upgrading to the latest router firmware, so I'm not on 2.0.37 and I did set the router back to Factory Defaults, rebooted, then configured it, and still no DCHP.
View 7 Replies
View Related
Nov 25, 2008
Problem I've been having with my laptop. Following the directions of a Dell technician while trying to resolve a separate problem, I deleted the partitions on my hard drive and manually reinstalled both Vista and all the drivers that were on the Dell CD that came with my laptop. When I tried connecting to the internet, Vista said I did not have any wireless networking hardware, but before the reinstallation it worked just fine. I am able to connect to the internet using a wired connection, but my wireless adapter still isn't working. I use Windows Vista 32-bit SP1
View 8 Replies
View Related
Jan 25, 2011
I use my desktop for streaming media throughout the house. I found it was causing lag for gaming most likely because it was taking up all the bandwidth for the router. We had a 2nd router laying around as well as a 2nd wireless adapter so we set up a 2nd network that was not connected to the internet for strictly media streaming.I attempted to change the network settings so the internet connection appeared as a public network so that streaming of media was hopefully diverted to the non internet wireless adapter.I want a faster way of transferring large video files from my laptop to my desktop. I recently bought a crossover cable to do this through direct connection.Both use the same user name and password as well as run the same win 7 pro however the desktop is the 64 bit version. I set up both ipv4 with the same addresses.When it has worked I am only getting a connection speed of just over 10mb and once I connect the crossover cable between the computers it knocks out my internet connection on the wireless card.
View 5 Replies
View Related
Jan 5, 2012
Im using my cousins internet because Im staying at her house for the hollidays and when I try to connect to her internet I get the message - Limited connectivity or no internet connection. I've tried to access the router settings but nothing will work, I've then tried to put the cable directly into my laptop and type the default ip adress into the address bar but still nothing
View 2 Replies
View Related
Feb 15, 2012
After changing these NIC settings I am no longer able to connect to the internet:
checksum offload -> disabled
speed/duplex -> 100 mbps full
I tried setting it back to what it was before to no avail:
checksum offload -> Rx and Tx Enabled
Speed/Duplex -> Auto Negotiation
I'm still able to ping URLs and IPs, but cant get to any websites or even the modem page. I tried rebooting,power cycling...nothing works so far.
View 2 Replies
View Related
Feb 18, 2013
I have a DIR-655 that was working for the longest time, then out of the blue it just decided to stop getting a connection to the internet. I can connect to the router, but for some reason, it will not get any network settings. When I check the status/device info/WAN section, it just shows:
[code]....
View 9 Replies
View Related
Jun 27, 2012
I can browse the internet just fine with no issues but when I try to access Cisco Connect (I have Linskys E1000 and Mac OS X) it says "you can only access your router settings when you are connected to your router." I don't know what the issue is. The only reason I need to access the settings is because I have been recently been having issues connecting to the internet from my Playstation 3.
View 1 Replies
View Related
Apr 15, 2012
I have a question about a netmask.How many netmask are there for IPV4?
View 5 Replies
View Related
Dec 4, 2011
I used to play online games with GameSpy. Suddenly, GameSpy Arcade just won't connect anymore, and i also noticed that almost everything related to GameSpy is blocked in my entire network. The only GameSpy site i can connect is gamespy.com, but GameSpy forums and gamespyarcade.com are blocked. I haven't changed any network settings, and i've tried to connect without firewall and without avast antivirus, but it just won't work. The only way i can get to those sites is through a proxy, i think that means that THEY are blocking me, and not my own network, right?
View 7 Replies
View Related
Aug 12, 2012
Do I need different network settings for when I am connected with my Rogers Rocket Stick vs when I am connected to my home Bell router? When I am at the cottage using the Rocket Stick, I have a good strong connection but, getting to web sites is extremely slow if at all. Win 7 on Acer Aspire One 522, 2 GB RAM
View 8 Replies
View Related
Apr 4, 2011
I had a disaster occur on my "guest" OS within VMware-Player. I had to start over from scratch! I am back in business, except for having the virtual machine recognized by my existing wireless network. The other two computers still communicate.I went through the wireless setup routine for the new VM. A new "ID" was assigned. Obviously, this is different from the one currently in use on the network. I have the settings info on a flash drive. Can I simply insert the FD in the other two computers and have the new ID replace the existing one?
View 14 Replies
View Related
May 21, 2012
I can't change my DNS servers. I went to my Network Settings and changed the settings for my DSL adapter. I manually changed the DNS servers to OpenDNS's servers, but when I looked again, the settings always change back to the localhost, 127.0.0.1. I tried to reset my DSL but still no luck.
View 3 Replies
View Related
Oct 10, 2012
I just restored my computer (Windows XP) to factory settings and it won't connect to the internet. I'm running an ethernet connection. I tried to look up a solution online but nothing has worked. Also, Im sure its not an issue with the modem, because all the other computers in the office are connecting to the internet just fine. It's only this one computer?
View 5 Replies
View Related
Mar 31, 2012
can i connect to internet without settings in modem is dat possible?
View 3 Replies
View Related
Oct 23, 2012
We have modem router 4-port with IP range 10.0.0.1 - 30 setting.one port goes to a library where we have a 8-port switch STLAB SWHUB-8p serving 2 pc with auto IP setting (internet works fine)and one port goes to another corner of the library to a switch TP-LINK TL-SF1008D V4.1 .4 pc are connected and a printer all are set with manual IP in an active rang of the router 10.0.0.10 - 14 they have to be on manual IP becuse of the ptinter.they cannot connect to the internet but I get the message connected.If I change them to auto IP - they can connect to the internet, the router gives them an IP.
View 3 Replies
View Related
Nov 13, 2011
i have internet connection which is connect using dynamic ip address but if i add ip address in Local Area Connection i get two networks, one is internet dynamic ip & other one is ip which i setup in Local area connection. so if i select LAN network for lan clients i can access lan. but now i have DLINK DIR 615 router so what should be my settings?
View 3 Replies
View Related
Jun 21, 2011
I am using the WNR200v2 for wireless and with a powerline adapter where should I set my speeds, 54Mbps, 145Mpbs or 300Mbps? Are there any other settings I should changeI have a road runner cable modem with 10Mbps download. I am streaming wireless to a PS3 slim 160gb, WDTV LIVE HD media streamer and a Directv HR24-500 DVR. I am using a powerline adapter kit to stream to a Boxee Box another media streamer. Most of my streaming is from the internet but, I occasionally will download something and then stream it from my HDD to one of my media streamers. My wireless signal only needs to travel about 30 ft. and the same for the powerline adapter
View 4 Replies
View Related
Oct 22, 2012
In my restaurant, we currently have a password protected wifi network for customers and staff. The load is typically light, so it's worked fine. Now, we're putting in a new cloud-based point of sales system, which effectively means that I need a totally uninterrupted, high quality wireless signal running to the POS terminal (in this case, an iPad). If the terminal is sharing that connection with 15 customers Facebooking on their iPhones, I imagine we'll have some signal issues. I'd rather not install a second network dedicated to the POS terminal. Are there any other possible solutions, i.e. a way to give priority to the terminal over other connections? A way to "split" the existing network so only a portion of it is available to customers?
FYI, current network speed is 20/mbs 2/mbs, and the POS terminal requires a minimum of 7/2 mbs.
View 5 Replies
View Related
Jan 9, 2012
I want to setup my Brother HL-2170W printer for wireless operation. The setup requires the wireless network settings for my D-Link WBR1310 router.
View 4 Replies
View Related
Jan 17, 2011
I recently added several devices to my wireless-g network: Xbox 360, an HTC Smart phone, and an old laptop my buddy gave me (in addition to the 2 desktops that were already on the network). Since doing this, I've had occasional buffering problems when streaming music or video, even when I'm only using 1 of the devices. I suspect that the Xbox (or maybe phone) is downloading updates in the background, even when it's turned off, and that is consuming bandwidth. Is there any way I can see a list of devices that are connected to the network and maybe even the amount of data being transmitted to/from each so I can find the culprit. when I play online, it says that my NAT settings are not open and that this makes it take longer to connect to other players. What are the risks involved in loosening the NAT restrictions?
View 1 Replies
View Related
Feb 5, 2011
When I set up my Linsky's Router,I set it up for 2 old computers (I can do 3 on it.) I bought a new laptop & added that. I no longer own the 2 older computers and would like to remove them & add my sisters laptop + the newer laptop she gave my little girl. I would also like to change it so that it is password protected instead of closed so that family & friends who visit may get online as well.
View 3 Replies
View Related
Oct 18, 2012
Type of Wireless Adapter I have: Intel WiFi Link 1000 BGN When I click on (Properties) and then click the (Advanced) tab, there is a list of properties on the left and a list of values to choose from on the right. I'm curious on what each property does and, which property/value would be most "effective" or "appropriate" for a certain location/situation I'm in.
View 1 Replies
View Related
