Linksys Wireless Router :: EA4500 Manual Way To Configure Network Gear
Aug 4, 2012
I have had several Linksys and Cisco routers in the past, and I'm a network engineer. My E3000 died after only 18 months so I had to run down and buy a new router, thus the EA4500.
I use the manual way to configure all my network gear. Nothing on my network changed, except the router replacement.If I leave the router default address at the 192 range, DHCP will issue a IP address. However, I do not use that range and after cdhanging the range, setting my start IP address, etc, I save everything and even tried rebooting the router to no avail. The router will not issue a DHCP addrss if you change the default range.
I can manually configure my clients with a static IP and all is good, no issues at all. I just can't get DHCP to work. My E3000 was configured exactly the same way and worked just fine, well up until two days ago.I have tried upgrading to the latest router firmware, so I'm not on 2.0.37 and I did set the router back to Factory Defaults, rebooted, then configured it, and still no DCHP.
View 7 Replies
ADVERTISEMENT
Jul 9, 2012
Do you know when will be possible to manual configure ipv6 settings? I have all parameters from my ISP but the settings on the router are only automatic and 6rd. Is it possible to enable this in future firmwares?
View 1 Replies
View Related
Nov 19, 2012
EA4500 router setting currently I am on an single fix IPs network, Internet access filtering by a Fortigate gateway, some IPs has Internet access, most of the IPs without, and we like to keep it that way.may I know what is the proper way to configure the newly added EA4500 router to working with "Guest Access" and my existing fix IPs network?
View 9 Replies
View Related
Jan 28, 2011
I purchased a computer with a pre-installed wireless card which was stated to be b/g/n compatible. When I go to setup a connection to the wireless network (through a Netgear WGR614 v8 router), it has no problem detecting it with a full five bars. However, when it prompts me to enter the password I do, but immediately afterwords another password box appears prompting me to reenter the password again. After repeatedly doing so, it will eventually say the password is incorrect. I know the it is correct because I've since purchased a Netgear USB adapter for temporary purposes and it connects using the password. I've even accessed the router to ensure the password I was using was correct and it is.
View 2 Replies
View Related
Aug 3, 2012
In the settings menu, there is no l2tp in which it was possible to configure a local address of the router. It should be: 10.155.41.41There is an option only for VPN server setup(10.255.255.254), but where it takes a local address that my provder has gave me? - it is not clear. At the same time in the status of the router receives a DNS correctly and the second address embarass me little bet DNS should be:
1) 80.252.130.253
2) 80 252.130.254
first dns is correct, and second one looks like: 80.252.45.86Maybe he does not take a local setting of ip adress via DHCP?
View 9 Replies
View Related
Nov 2, 2012
I just installed my EA4500 router and it was amazingly simple. My only question is it shows two wireless connections available: The secured one I set up and the another network with the same name that says "guest" and is NOT secured. Is there a way to either disable the unsecured guest network or to secure the guest network?
View 2 Replies
View Related
Apr 9, 2012
I recently purchased a Linksys EA4500 Dual-Band N900 Router with Gigabit and USB. Everything set up great with no problems and after a day or 2 I managed to get all home devices connected (2 laptops, 2 printers, an iphone, 1 tv, 1 blu-ray, an old desktop, and a tablet). Everything was connected right and working and I installed the Linksys app on my iPhone which let me see what devices were connected and all that. Well, last night, an unknown device showed up as a connected device. It's labeled as: android_(insert string of characters) and has a MAC address. I've tried and tried to identify what this device is and I can't. Everything else on our network is still showing up independently of that device. I'm worried that someone using our connection and possibly putting our device security at risk. What can I do to A) try to identify what the device is and B) if it is an intruder, block it's access.
View 9 Replies
View Related
Jan 7, 2013
just bought the EA4500 new, setup the router with computer plug-in RJ45, after I change my network network to "LinksysOne", I can connect to the network wireless. But when I connect it with hard wire/RJ45, it shows "cisco27205", but I cannot see "cisco27205" with wifi, neither with RJ45 connection cannot see "LinksysOne". Why this happen? is this normal?
View 1 Replies
View Related
Feb 14, 2013
I have been experiencing problems with my Linksys EA4500 router not being able to find my network. I reset the router and it was able to find my network, but said it was out of range despite it not being so.
View 1 Replies
View Related
Jun 23, 2012
I have got a Cisco EA4500 recently installed and it's great. I was very excited about the USB part as I attached a WD hdd to share the media. All good apart for two issues for which I can't seem to find a solution:
1. Transfer speed: Playing a movie over wi fi from the attached HDD works fine. However, if I try to copy the avi file from my mac to the attached hdd or vice versa the transfer speed is around 1 - 2 Mb / sec. How I can improve the speed?
2. Can't write files on the HTF+ partition
My hdd has two partitions: 1 x NTFS and 1 x HTF+.When I try to copy a movie from my mac through the Wi Fi on the HDD it would not let me on the HTF+ partition although I logged it as an Admin. I say I don't have the priviledges. However, on the NTFS partition works fine. Full r/w priviledges seem to work only on NTFS. Is there an issue with mac partitions?
View 2 Replies
View Related
Aug 26, 2012
My two devices access the 2.4 ghz wireless network fine on my EA4500.Both my devices, laptop and iPhone4, have N rated network cards. What do I need to use the 5.0 ghz wireless network on the EA4500?Can the iPhone4 use a 5.0 wireless network? When I try to add the 5.0 ghz Wi-Fi to my iPhone4, it cannot find the named but hidden SSID network??
View 2 Replies
View Related
Dec 10, 2012
I noticed a bug with the EA4500 (could possibly be all EA series) router that linux machines cannot see network share with the smart firmware. Just right after I upgrade to the smart firmware, all my linux machines cannot see any network shares at all. I downgrade to the classic firmware, every thing works like a charm.
View 5 Replies
View Related
Feb 6, 2013
I want to setup a Linksys EA4500 in bridge mode behind my separate firewall to access the domain LAN. I'd also like to supply a wireless guest network for clients. In bridge mode the EA4500 doesn't seem to offer a separate guest network. Is there any solution other than adding another Wireless router just to serve up the Wireless Guest Network?
View 6 Replies
View Related
Feb 3, 2013
I just purchased a Linksys EA 4500.I set up the wifi properly, with laptops, tablets, smartphones and printer. The wifi network worked fine for a couple of days.But now one of the laptop "refuses" to see the Linksys wifi network. The other devices are still connected and running regularly.
The notebook that does not connect anymore is an ACER 5740DG with an Atheros Network adapter and Windows 7 installed. This notebook is otherwise running fine.At the beginning it was connecting ok and we never had any problem at all with the previous router Belkin_N+_7991AC, that I changed just for speed.
Now the Linksys network is simply not visible to such notebook in the "Available Connections List" that I get clicking on the WiFi icon in the bottom right, while a number of other wifi networks (not mine) are clearly visible. Of course I restarted the notebook properly. For one time I got the visibility of the Linksys, I entered the password and then it was not possible to see the network anymore.No error message from Smart WiFi software.
View 5 Replies
View Related
Jun 24, 2012
I've recently purchased a Linksys EA4500 router. I've got home, I've used the installation guide CD thingy, connected 3 of my laptops wirelessly, no issue there.However when I tried to connect my 4th laptop problems came along. The problem I was dealing with was that I couldn't connect to the router. I mean I could see the network name appearing in the list, but when I tried to connect the network would just dissapear from the list, not connect, and wouldn't back on the list unless I've reset the laptop. Anyhow I've ignored that computer because I thought it was two years old and it might have had a wireless network adaptor issue, although it was conneting with no problem to my former router D-Link DIR 365.Anyway, just yesterday I've purchesed a brand new netbook (Evolio U9) and it doesn't see my router, although it sees all the other connection availables (my neighbors' wirless networks), I even connected to one of them just to test if anything was wrong with the netbook.
I also have problems when trying to connect with an Iphone 4. Well, it does connect, but the connection to the iphone just goes on and off making it impossible to use. It's really strange that all the 3 Iphones in my home have no issue connecting, not even my Glaxy S3, nor any of the Smart Tvs, nor the printer.Does the router have any number of limited connections available? The router configuration is the ones done from the CD. I've only assign a SSID and a WPA password.Please note that all the computers above are GENIUNE Windows
View 9 Replies
View Related
Sep 19, 2012
My EA4500 router seems to drop mine and my wife's iPhone wifi connection at what appears to be the edge of my router's range. When we come back in range, our iPhone's intermittently give the error "Unable to join network.". And we're stuck in that mode. When I check the Devices menu in the CCC interface, I notice the iPhone device is configured and still online. However the "x" box to delete the device is greyed out because it's online. So how do I get out of this state and have my iPhone connect
View 2 Replies
View Related
Apr 17, 2013
I purchased this Router about 2 weeks ago as a phased upgrade of our Home Network, primarily to enhance media streaming. It has the latest firmware preinstalled from the factory. Prior to the purchase and installation of the EA4500 Router I replaced my old Motorola SurfBoard SB6120 DOCSIS 3.0 Cable Modem with a Motorola SurfBoard SB6141 DOCSIS 3.0 Cable Modem. My old Linksys E2000 Router worked perfectly with the SB6141, with the exception that the E2000 wasn’t IPv6 enabled, but does have 10/100/1000Base-T Ethernet (RJ-45) and Internet ports.
The EA4500 has been installed for about 10 days and seems to have improved local network speeds and I don’t seem to be having any Internet connectivity issues. However, there are some disturbing issues with the EA4500 and the AE3000 I purchased. There are 11 devices connected through the Router; a Dell Desktop (wireless with the AE3000), a Dell Desktop (Ethernet), a Dell Laptop (wireless), 2 Canon Printers (1 Ethernet and 1 Wireless), 2 Western Digital 1TB MyBookLive Network Drives (both Ethernet), a WD TV Live Streaming Media Player (wireless), an Apple TV media player (wireless), an iPad (wireless), and an Android Smartphone (wireless).
Issue 1 – The Linksys Smart Wi-Fi interface appears to be unreliable at times!!! I’ve read about this problem here on the Community involving the EA6500, so I don’t know if this is a Linksys Server issue, as suggested in a few responses, or a bug in the Router firmware, or defective hardware. However, when the interface locks up, it can’t be accessed from a wireless or wired connection. Usually, powering down the Router and then powering it back up and restart will allow it to function again. However, at times before the interface completely locks up it shows either just a white screen or the security screen will show no firewall features enabled. This is a little scary, so I’ll do a complete reset and setup; this is becoming a pain in the rear! Is there any hope for this being fixed, in this Router, not the next generation?
Issue 2 - All of my network devices show up in the Router’s Device List. Except for the Apple devices they also show up, when they are online, in Windows 7 Explorer under Network and when you click on Network they are correctly displayed as Computers, Media Devices, Network Infrastructure, or Storage. However, when you click on “Open Network and Sharing Center” and then click on “See Full Map”; it fails with the response “Windows cannot create the network map. Responses from other devices on the network are delayed or there is an incompatible router on the network”; no device map is shown. When I follow the link for more information, the only thing that stands out is “A device on the network, such as a hub or switch, is not working properly or is not compatible with the Link Layer Topology Discovery (LLTD) protocol, which Windows uses to create the map. To fix this problem, disable the device, turn it off, or remove it from your network”. All of my network devices showed up on the Network Map with the old E2000. This issue is the same on all of my computers, either wired or wireless.
I’m having with the EA4500 and the AE3000; they are both probably going back to Amazon.
View 3 Replies
View Related
Sep 15, 2012
I have successfully set up a guest network on my EA4500. Guest laptop associates with guest SSID just fine. Then via IE, it gets prompted for the guest password, which is entered and accepted just fine. At this point guest laptop is on the network.
BUT... at some point the guest laptop will need to reauthenticate (I don't know what the timeout is, but maybe one or two days?). Anyway, it's at this point that IE presents the guest network login page. But now after typing in the password, "enter" or clicking on the button does nothing. It looks like the guest web page doesn't get loaded properly or completely, so the reauthentication can't complete, therefore can't get to the internet. So, while in this state, I've also tried Firefox and Chrome, and same thing, no action when trying to submit the guest password. Tried rebooting guest laptop, and still same problem. Only thing I've found so far that works is to reboot the router. So I'm guessing there's a problem with the guest/web server on the router?? It's a real pain to have to reboot the router every day or two, when I've had other Linksys routers run for months without having to touch them.
I was running CCC 2.1.38 when I first noticed the problem. Since then I've downgraded to Classic 2.0.37, but it seems I still have the same problem. Again, I can connect & authenticate just fine initially, but when reprompted after some period of time, it doesn't work.
I've tried contacting Cisco support, but it looks like I'm at 91 days since purchase and thus outside of my 90-day complimentary support, so they happily provided me with the premium support options just to have the honor of talking with them. Guess I shouldn't have spent so much time trying to figure this out myself.
View 9 Replies
View Related
Dec 24, 2012
Where do I find a manual for the LinksysE1000?
View 1 Replies
View Related
Aug 31, 2012
Where can I find a log or list of devices that attempted to access my EA4500 wireless network?I am using the cloud services to monitor my EA4500 usage in an apartment environment.
View 1 Replies
View Related
Feb 2, 2013
I'm trying map the USB hard drive connected to my EA4500 router as a network drive in Windows 7, and it works perfectly until I enable secure folder access on the router.
After enabling secure folder access, and not changing any other settings on the router I first unmount the drive since it was set up without credentials and doesn't work that way any more. When I try to remap the drive I use the same address, but select "Connect using different credentials" When it prompts me for the log in info I try using the router admin account, but it fails to connect. Windows network diagnostics tells me the device refused the connection. I proceeded to set up an account on the router under the folder access settings with the same username, and password I use on my computer, and tried to connect it without checking "Connect using different credentials" (And typing them in manually if that matters) with the same results.
Even with secure folder access enabled I can still reach the drive just fine by typing "ftp://192.168.1.1/" into file explorer. It prompts me for a username and password, I put in the admin credentials, and I'm in. Even the account I created with the same username/password as my computer works this way.
After disabling secure folder access everything works perfectly fine again... I would MUCH rather do this with it though.
Following these directions: [URL] When clicking the browse button the router shows up when secure folder access is disabled, but does not after it is enabled. I've looked through my windows sharing settings, and haven't noticed anything that should cause problems, pretty much everything is enabled. I've also tried turning off my firewall with no success.
View 7 Replies
View Related
Jun 19, 2012
I have a Linksys EA4500 setup on my corporate network for wireless access. I have enabled the guest network and from all I can tell it's on a seperate subnet from my internal network like it should be. 192.168.x.x My internal is on a 10.x.x.x network. I conenct to the guest network using a laptop and I'm prompted for a password to get to the internet, which I like. The one issue I'm seeing is when I'm connected to the guest network I can still do an RDP session to internal resources. How is this possible if the guest network is on a seperate subnet?I take a laptop which has not been joined to my domain, connect to the guest ssid, and then open an RPD session and enter an IP address for an internal server and it connects. Is there a setting to keep this from happening
View 6 Replies
View Related
Apr 14, 2012
I recently bought the E2500 Router and I am using the EA2500 Adapter with it . I have this set-up on 2 Desktop PC's . 1 Pc is working just fine with this set-up . The other keeps giving me an Error message of "Invalid Key Manual" . What does this mean ? The adapter is working because it does find the Router as a usable connection . It just isn't able to connect to it and keeps giving me the same Error message .
View 8 Replies
View Related
Apr 27, 2012
The device has been trying for days to auto-download and all it does is fail constantly. Saying that my connection is slow - gee, I have FiOS, I know it's not slow,maybe it's your Servers Cisco?Well, where can I obtain the direct DL link to that firmware file instead of relying on an unreliable device to get it and apply for me?
View 4 Replies
View Related
Jun 6, 2012
I have a 4200V2 acting as a Router and (2) more E4200V2's acting as Access Points,The E4200V2 acting as the Router is at Firmware 2.0.37, but, the other Access Points are at Firmware 2.0.36.126507 and when I try to have the Firmware Upgrade Utility in Setup update the Firmware it gives me this message:"Current Version: 2.0.36.126507Available Upgrade: Your router software is up to date"Where is the downloadable Firmware 2.0.7 located?How do I upgrade the Firmware Manually to 2.0.7 and should I ?
View 6 Replies
View Related
Mar 26, 2013
E4200v2, firmware 2.1.39.145204
Router says "Invalid IP address" when I try to make a manual IP address reservation of the IP address range.
Example: local network 192.168.1.0/24, where .1 is a router, .2 is a reservation, .20-.50 is a range for DHCP.
Before upgrade I didn't have this problem.
View 6 Replies
View Related
Jul 6, 2012
I have ASA5585 Firewall between my WAN Cloud and LAN Network. I plan to configure Layer 3 Vlan Interfaces inside FW and it would be Layer 3 gateway for some of Subnets. Layer 3 VLAN Interfaces are planned to be dual stack containing both IPv4 and IPv6 Address stack.
I plan to configure 6 to 4 Tunnel with my Hub Site where we have native Ipv6 awareness. One tunnel end point would be ASA and the other endpoint would be Hub site WAN Router/L3 Switch. So IPv6 traffic hitting to vlan interfaces on ASA would be policy checked and routed over tunnel interface to Hub Site.
6to4 Tunnel manual tunnel configuration on ASA. I have configured such tunnel on L3 Switch or Router with following config.
Int tunnel xyz
ipv6 address <ipv6 address>
ipv6 enable
tunnel source <loopback address of my L3 Switch>
tunnel destination <loopback address of my hus site L3 Switch/Router>
tunnel mode ipv6ip
end
I need to implement something similar in ASA. How can I do that?
View 2 Replies
View Related
Oct 17, 2012
Any problems with the guest network on the ea4500 with the cloud firmware? I am losing guest clients after about 24 hours and the re-authentication fails. you enter the guest password and nothing happens until you reboot the router.
View 2 Replies
View Related
Jul 8, 2011
I've downloaded the driver for a tenda usb adapter. What else do I need to do to connect to the WRT54G network? I'm currently connected via an ethernet cable. Running Windows/7.
View 1 Replies
View Related
Jun 27, 2012
I have a Cisco 4200 Wireless Router connected directly to my cable modem. To extend the wireless range I purchased a Cisco 2500 Wireless Router. As the house is "wired," I can connect the Cisco 2500 to the cable modem in a room separate from the Cisco 4200. My question is how do I configure the Cisco 2500 to connect to the network and provide wireless coverage from both routers.
View 6 Replies
View Related
Feb 1, 2013
The situation is Main house running Linksys EA4200, I have a garage apartment rental that is to far away to receive the wireless guest network.I ran a cat5e to the apartment, can I configure the EA4200 to allow the WAP54G access point to use the guest network? I want to prevent my renters from having access to the home network, but just have basic internet access separate/outside my network.
View 6 Replies
View Related
Jan 6, 2013
I got error message everytime i try to configure home network defender and i tried to find the solution but no luck but everytime i click and enter my email and password i get this message, i bough this router recently and the only troubles i have is with this
View 2 Replies
View Related
Jun 6, 2012
I am trying to improve the coverage of my home network.I have Fios, and with the existing Wireless capabilities, there are several dead and low coverage areas in my house. This is due to a combination of where my router is (Limited by input feed) and the confuration of the house.
I have CAT-5 running to most rooms, so adding wired devices is not an issue. I went out and picked up an EA4500 router, and my plan was to convert my Fios Router to a bridge and use the EA4500 as the DHCP server. However, even with this router, my coverage is not improved. My preferred solution will be to get 1 or 2 additional access points that I can plug into my wired network, however, I would want to have a common SSID for the entire network.
View 8 Replies
View Related
