Microsoft Windows [Version 6.1.7600]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersAlex>ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : Alex-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
[code]....
My laptop is not connecting to the internet, I know that it is not a router problem as my mine PC and Notebook are connecting with no issues.I have removed all router devices as had an new once once it was last working.I tried this morning to set it up again without success. I have compared to setting with my pc and have found the difference is with the IPV6 connectivity.
View 6 Replies View RelatedI am using window 7 on my laptop. I am using broadband internet (not wireless etc) via my external lan card but IPv4: IPv6: No Internet access shows.
View 4 Replies View RelatedI have Dell XPS L502X, Windows 7 Home Premium.My internet was working last night but when I turned it on this morning it would not connect.It is connected to my bt homehub with full strength but no internet access. It says IPV4 No Internet Access. I tried using a wire to connect it but that did not work either.Other devices are connecting. So can't be a problem with the internet itself. [code]
View 5 Replies View RelatedLenovo G550 with windows 7 shows that the Internet is connected but the IPv4 and IPv6 connectivity says no network access. I updated and reinstalled drivers, typed in some cmd command and restarted computer with no success. I also called tech support and they had me go into safe mode, the Internet didn't work there so he said it was a driver problem but wouldn't fix it.
View 6 Replies View Relatedmy ipv4 show limited and my ipv6 also show limited when connect internet through wireless..yesteday can wep but show limited connectivity...
Windows IP Configuration
code...
well a couple days of go it was working fine until i updated windows 7 now it says im connected to the internet but when i go on it dosnt load anything, and when i go check it says that "IPv6 connectivity: No Internet access" how ever the IPv4 is connected to the internet, should i restore settings to osmetimes earlier this week
View 2 Replies View Relatedwireless network connection connected but limited or no connectivity
View 1 Replies View RelatedMy mother's computer periodically loses internet connectivity. This happens regardless of the browser (IE or Firefox). She must restart her computer to get access again. This happens regardless of her internet connection. She uses verizon at her home and accesses through my wireless router when visiting. This also happens if she is on a public access network such as a hospital
View 1 Replies View RelatedI am currently in Thailand and I have been using dozens of different wifi connections around Australia and South-east Asia without a problem for the last year. I moved into a new place yesterday and when I tried to connect, it has the little yellow triangle with an exclamation mark, over the wireless symbol on the taskbar. I tried the troubleshooter but it says turn the modem off an on, I don't think I can do this, I'll try and ask reception but I doubt they will let me.
No-one else at this place I am staying has had the same problem as me. The signal strength is "excellent", the wifi password is correct. I have windows 7 on a Dell Inspiron.
I am at my old place now, where the internet works. I downloaded the internet test thing from one of the stickies, I'll go and do that at my new place and post the results soon.
I have configured ASA 5505 for remote access VPN to allow remote user to connect to the officce LAN from remote locations. VPN working fine, users can access offce LAN and sahred resource etc but once they connected to VPN, they can not browse the internet ? Internet browsing stop working as soon as their VPN client connnect with ASA 5505 t, once they are disconnected from the VPN , again they can browse the internet.
Does ASA 5505 blocks the internet browsing for VPN users ? Is there anything else I need to congfure to make sure VPN users can browse internet? Do I need to configure Split Tunnleing , NATing or routing for the VPN users?
I currently have ipV4 as the setting on my DIR-825. Other posts seem to want ipV6 which is more secure but is not possible with a DIR-825 Rev A1. I have two routers, a primary router (DIR-825 Rev B1) capable of ipV6 and a secondary router (DIR-825 Rev A1). If I implement ipV6 on the Rev B1 router but keep ipV4 on the secondary router, will this improve the security, or will it just mess things up so nothing works?Certain devices (cell phones and most Tablets) don't deal with ipV6 very well at all. The ones I have tested flat don't connect to the wireless network if the router is set at ipV6. Is ipV4 adequate for a Home/Small Business Network when trying to implement Remote Access and VPN?
View 2 Replies View RelatedI have a dell inspiron 15 and I've been having trouble fully connecting to my wireless internet. It says I have signal but gets stuck on identifying the network and I have limited IPv4 and IPv6 connectivity.
Here's the ipconfig if you can identify the issue with it:
Windows IP Configuration
Host Name . . . . . . . . . . . . : M-PC
Primary Dns Suffix . . . . . . . :
[Code].....
I am using the Vostro 3360 with win 7, I did used the hotspot station software accomplish with the WiFi driver before and worked fine. However, the hotspot is not working as the ipv4 is showing 'no internet connect'. And my iPhone cannot connect it too.
View 1 Replies View RelatedI've created a hostname & account with [url].... for my vpn setup.It was working fine until 2 days back. owa was accesible and configured MS Exchange on iPhones.
Suddenly it stopped working.The updation of IP from ISP is happening @ chnageip.com site, but when we ping the hostname, it is not resolving to new ip and is not pinging.Our users outside the coporate's internal network is unable to access.
Any issues with the WAP200 and web connectivity? The internet stays up, but after awhile, any browser I use cannot hit the web. Email, chat, and any other internet reliant apps are fine.Just web.
View 1 Replies View RelatedI have a question about a netmask.How many netmask are there for IPV4?
View 5 Replies View RelatedSetting up my wifi network with an old BEFSR41 Router and WAP11 wireless access point. Have laptop with XP Pro that connects just fine without encryption but as soon as I try to use WEP I get the "Limited or no connectivity" error. When prompted, I type in the same passphrase as the one I used for the WEP 128bit encryption while setting up the WAP11 for my network.
View 4 Replies View Relatedrececntly we have installed 2504 WLC in of branch office, I can able to log via console but it is not coming over LAN not even showing in CDP, all config seems to be fine in wired side & WLC side & physical connection also fine...LED also green.I am seeing log message in WLC, is this related to License issue
View 2 Replies View RelatedI have a brand new Dell Ispiron 14z Ultrabook. I keep having problems with Wi-Fi connectivity. I can use the Ethernet connection fine, but when I try to connect to Wi-Fi I keep getting no access or limited connectivity. I have other devices and laptops that work fine on the same Wi-Fi networks
View 3 Replies View RelatedI've searched the forums and found similar problems that relate to mine but after trying done of their solutions with no success I decided to make a new thread. This problem started 2 days ago with the same network I've been using for about 2 months.I'm running vista sp 1. I use google chrome and when I try to open a page it says unable to connect to proxy server. I changed the lan setting s (unchecked the box for using a proxy server for my lan) and now the page says the dns lookup failed.
View 1 Replies View RelatedWe have netgear router and 3 laptops which were all working on the internet fine but one laptop has had a full recovery done on it and now won't connect it just says there is limited connectivity, what it could be as the net is still working through Ethernet and the other laptops through wireless. Its windows vista.
View 5 Replies View RelatedI currently have a 20MB down and 2MB internet. I have a Cisco Linksys E4200 with Firmware Version 1.0.05. We have a two bedroom apartment, one of the bedrooms is our office which is by the front door. We have the wireless router and our modem in the office. We have an apple TV in our living room that is connected to the wireless internet. Every time we get random times where the video output is very pixely and seems we are streaming shows/movies on a 56k modem.
View 1 Replies View RelatedI'm currently living in a shared house right now, and for our internet, the landlord has us on Virgin Media's basic package, which in theory should be netting us around 10mb (according to the lady that I spoke to on the phone from there anyway). It comes into the house via a cable, then goes into a modem, and then that modem is connected to a wireless router which pumps it out into the house for everyone (at least it tries to anyway - read on!). That's what I can make out from what I can see at least.
Now, when I connect my laptop to said router via a cable, the internet works fine, and doing speed tests, I get relatively consistent results around the 10mb mark that they should be. However, when I try to use the wireless with my laptop, even sat right next to the router, most of the time, the internet doesn't seem to work at all. Webpages just load indefinitely, or I get an error message saying that the connection was reset whilst the page was loading.
On rare ocassions where the wireless does work, and I run a speed test, then I'm lucky to see results close to 1mb, and in my wireless properties, the speed usually says something like 18mbps.
ISP : ShawPC >> SMC Modem/Router >> Netgear Router >> PS3 and Denon Stereo Receiver ( Both hardwired to Netgear Router), 2 Laptops and 2 Phones connected wireless- The reason I do not use the SMC as a router is because I was getting terrible wireless signal- When everything is working properly I am getting great speedsroblem : I keep losing internet connectivity. On the wireless devices I still have have great signal strength but no connectivity. I need to run netgear genie oripconfig/release/renew to get it back. It always comes back but this is annoying.It also does this on the PS3 and Denon which are hardwired to the router..as with the other ones if I reset the router or do a connection test on the PS3 it will fix it. Finds IP but no internet connectivity.My PC has also started to lose connectivity and I need to do a ip release/renew and it comes back fine.The fact that this is happeneing on my PC would lead me to believe that it may be an issue with the Modem/router. Are there some settings I need to change on it since I am only using it for modem purposes? I have disabled the wireless on it but I don't think that would be the issue anyways
View 14 Replies View RelatedJust recently my internet got slow, and when it got slow nothing worked. I can connect to the internet and get on skype and some websites but when i try downloading something it says No internet Connectivity Detected.
View 2 Replies View RelatedNo connectivity for any application other than Internet Explorer.Can not update any applications. Can not sign in to any apps, such as Paltalk, AIM, etc.Internet Explorer runs fine.
Computer Specs:
-Compaq Evo N800c
-Windows XP SP3
-Pentium 4 - M 2.0ghz 1.99ghz
-512MB RAM
Computer was bought refurbished and I believe XP had been re-installed and I am not sure if all the factory divers were properly re-installed...
Currently have a setup where we have multiple SVI interfaces in a VRF on a Catalyst 6500 Switch. All these SVI belong to the same VRF. In order to achieve connectivity for hosts within the VRF to access hosts outside the VRF (Hosts reachabe via the Global Routing Table (GRT)) I am thinking I need to configure 2 things
1. Creating a summary route for all the subnets within the VRF in the Global Routing table.
<Config on 6K in Global Routing Table>
Note: 10.10.10.10 is the ip address of loopback 10 and this loopback 10 is in VRF Red
ip route 172.16.0.0 255.255.0.0 loopback10 10.10.10.10
2. Create a couple static routes within the VRF for networks that reside in the Global Routing table but which are not local to this 6K.
<Config on 6K within the VRF Routing Table>
Note: 1.1.1.1 is the ip address of loopback 1 and this loopback 1 is in the GRT or not assigned to a VRF
ip route vrf Red 172.32.32.0 255.255.255.0 loopback1 1.1.1.1 global
ip route vrf Red 172.32.40.0 255.255.255.0 loopback1 1.1.1.1 global
ip route vrf Red 172.32.50.0 255.255.255.0 loopback1 1.1.1.1 global
I have read through some posts and it seems to indicate that I cannot point to a loopback interface as it is not a point to point interface. How this solution can be achieved. The reason I was pointing to a loopback was so that I am not tied to a particular physical interface and for the summary route that was created in step 1 really not sure what L3 interface I could point to since I have multiple SVI's that are in the same VRF. Would I also need to create that same summary within the VRF. I don't intend to since I am assuming that once within the VRF the more specific connected interfaces would take affect and forward respectively.
In addition to the above I also need determining the forwarding behavior when there is a ip helper address configured under the SVI's which are in a VRF but the ip address for that helper is not part of the VRF. I would think if a static route is configured under the VRF for that helper address network pointing it to the Global Routing table it should work. The config for that would be
ip route vrf RED 172.32.52.5 255.255.255.255 loopback1 1.1.1.1 global
I understand you can't assign an IPv4 Address to a "port". But here's my issue. I have two network cables attached to a managed switch, the location of the two cables are very important. Two computers attached to the said cables.I would like to communicate with one of the computers on PORT 1 and PORT 2, regardless of what computer is plugged into them. They get there IP's via DHCP, and a static IP wont work - as the computer plugged into PORT 1 or 2 may be different.So. I have two ports on the switch that I always want to communicate with the computer on the other end. But I don't (will not) always know the IP address of the computer(s) connected.
View 12 Replies View Relatedhas quite frankly gotten me absolutely annoyed . I've tried just about everything, from using the netsh commands to changing the dns to 8.8.8.8 or that other one or the other. Nothing is working, I unplugged the router, problem persists, I disabled IPV6 problem persists, I restore, problem persists. The only clue I have is my router, and mysteriously, there are TWO of my computer on it. It might be nothing but most certainly has caught my attention. Also, it gives me this info about my media being disconnected
View 14 Replies View RelatedSo I have been trouble shooting this for just over a day and still nothing, but anyways. My computer says that I am connected to the wireless router and that I have great signal strength but I have no internet access from either my IPv4 or IPv6. I have been using the cmd commands such as netsh reset, and the like. I have restarted both modem and router a few times as well as my computer. Also just did a recent avg scan and firewalls are all off. This is all coming from my mac laptop which is connected just fine which leaves me even more confused.
View 12 Replies View RelatedI have a Windows 7 computer. My boss changed the IPv4 address of this computer. Nowalthough all computers can connect to the network, they can no longer see this computer. And this computer cannot connect to the other computers.
View 1 Replies View RelatedI live in a shared house, and I am the only one who has been experiencing issues connecting to the internet. I have to ask a housemate to reset the server, as this is the only thing that works.
When I am unable to connect, and I use command ipconfig, the following appears: Autoconfiguration IPv4 169.254.23.29 On the occasions when I am connected, the following appears in its place: IPv4 IP Address: 192.168.0.2
One tip that I came across was to check the box (Wireless Network properties, Connection tab) for "Connect even if the network is not broadcasting". I had hoped this simple solution would assist, but to no avail.