Cisco :: Can't Ping From Outside To The (online Host) PC
Aug 26, 2012I tried to ping from the "online host" PC to the outside,it succeeded. However, I can't ping from outside to the "online host" PC.
View 2 Replies
ADVERTISEMENT
Cisco VPN :: Pix 515e - Remote Host Cannot Ping Any LAN Host
Jun 27, 2011I have a host that can successfully connect to a PIX 515E (7.x OS) via VPN Client; however, I have no IP routing to the LAN from the remote host.The VPN IP pool works finem,The LAN default gateway is the inside interface on the PIX; the network is flat L2 behind it.The default route on the PIX points out; no other routes are defined,The VPN remote host can be pinged from LAN hosts, but the VPN remote host cannot ping any LAN host, not even the PIX inside interface.
View 2 Replies View RelatedCisco VPN :: ASA 5510 Ping / Communication Host To Host
May 7, 2012ASA 5510
Ver 8.2(5)
I have been looking all over the place for the answer of how to allow clients on an IPSEC VPN to ping from host to host.
Can Pure IPv6 Host Ping A IPv4 Host?
Feb 10, 2011I'm just wondering if its possible to ping an IPv4 host using the IPv6 host assuming that the NAT64 has already been implemented?
[code]...
Cisco Switching/Routing :: Can Ping From R1 To R3 SVI4 Gateway But Cannot Ping Host
Dec 12, 2011I set this up and I can ping all the gateways but never the hosts. I was hoping I could make these links between 6500's a mix of L2 and L3. Check it out. They are connected in a linear fashion R1--->R2--->R3. I can ping from R1 to R3's SVI4 gateway but I can never ping a host on that SVI4. I was hoping that I could use the port-channels between 6500's as routed links or as trunk links depending on the type of traffic....thought it would ease the migration. I suppose I could always get rid of the port-channels and just make separate L2 and L3 links between the 6500's.
View 3 Replies View RelatedLinksys Wireless Router :: Host Online Games With E2500?
Jul 31, 2011How hard is it to host online games with a E2500 Router?
View 1 Replies View RelatedLinksys Wireless Router :: Setting Up E2500 To Host Games Online
Aug 4, 2011How do I go about setting up my E2500 Router to host games online? I'm talking like Deer Hunter 2005!
View 4 Replies View RelatedLaptop Won't Go Online - Cannot Ping Router
Jan 10, 2013I shut down my laptop over Christmas and when I returned it would no longer connect to the Internet. It will connect to the network but not the Internet. Every other device I have (blu-ray player, work laptop, iPad, etc) goes online without any problem using the same router and network. I am running windows 7 and a linksys router that is a year old. Its a Dell Inspiron 1545. I was connected wirelessly but have a LAN connected now while I work this. Neither will connect to the Internet. I have terrible trouble with routers and am terrible when it comes to hardware.My computer skills for this sort of thing are only average. Windows can't communicate with the device or resource (primary DNS server)Security or firewall settings might be blocking the connection.I've looked for ideas in various places online and have tried many things: [code] Next step is to throw it all out the window! I have a small home business and people are waiting for contracts that I can't currently deliver.
View 19 Replies View RelatedHigh Latency / Ping In Online Games
Jan 4, 2012So I am at a bit of a loss here. For the past week or so, I have been getting random spikes of high latency in online games like World of Warcraft/Star Wars: The Old Republic/League of Legends/etc and I have no idea what could be causing it. My ping used to run around 30-80 and lately is has been spiking from 100 to over 700 randomly. I have tried everything I could think of like not using my router, power cycling my modem several times, making sure my drivers are updated, no programs in the background causing it, no firewalls/anti-virus programs causing it, and several other little things like that. I have also called my ISP and they said everything seems to be working fine. And here's another weird thing, according to speedtest.net, my service is running as it should be: [URL]. The server my service is connecting to is in the next town over which is ~15 minutes away so that couldn't be it either.
Here is my system specs:
OS Version: Microsoft Windows 7 Ultimate, 64 bit
Processor: Intel(R) Core(TM) i7 CPU 920 @ 2.67GHz, Intel64 Family 6 Model 26 Stepping 4
[Code].....
Getting Ping Spikes While Playing Online Games
Jun 17, 2012try to play online games but i can't because i get so many ping spikes. I started investigating and i've noticed that i'm getting ping when pinging my router. I'm using wlan and i can't use ethernet. Also the bandwidth is really low on the connection, 512 kbps Also, there are more than 1 computers connected, even if they dont use the connection constantly
View 11 Replies View RelatedCisco WAN :: 871 Can't Ping From Host
Jun 30, 2012I'm going through the CCNA training and I'm setting up my DHCP server on my 871 router. I have my cable modem into the WAN port on my router and have 1 host plugged directly into Fastethernet 1. I can ping any IP I want from the IOS prompt but I only have local access from the host. [code]
View 4 Replies View RelatedHigh Ping And Packet Loss During Online Games?
Jan 24, 2013about 4 weeks ago we started experiencing Packet Loss and High Pings while playing games. This affects our 2 PC's and our PlayStation 3 (Since we use them for gaming). We have contacted our ISP several times regarding the issue but each representative we have talked to has had different ideas of what the problem is. They replaced the modem twice which did nothing, so I then purchased 2 new Router's (DIR 601 N150 & DIR 835 N750+). Neither of them solved the issue. my ISP also says it isn't the Internet Cable that is causing the issue. My Download Speeds and Upload Speeds are right where they should be but the ping and the packet loss is the problem. I also contacted DLINK (Router Manufacturer) to see if they had and all we did was upgrade the firmware version and change the Wireless channels which also did nothing. I have plugged this PC into the modem with an Ethernet Cord and played games and all the issues were gone which leads me to believe that Modem and the ISP aren't the issue.
Things I've Tried:
-Resetting the Modem
-Testing each Wireless Channel on my Router
-Enabling and Disabling 802.11n and 802.11g on the router
-Changing the QoS settings
-Installing Software such as Gamebooster and Advanced System Care
-Disabling all Antivirus programs and Firewalls on the PC's
-Using a friends Modem instead of the Cogeco one
[code]...
OS: Windows 7 Home Premium 64-Bit
System Manufacturer: Acer
System Model" Aspire M5802
Processor: Intel Core 2 Quad CPU
RAM: 8GB
Graphics Card: AMD Radeon HD 7800 Series (7850 to be exact)
Cisco :: Can't Ping From ASA To Host In GNS3
Apr 24, 2012I test all devices using ping command, from ASA to router was fine (on both interface) but not to Host , and host to router was fine, but only on directly interface(F1/0), and to ASA was not success. am i miss something in my configuration?
View 5 Replies View RelatedCisco :: Can't Ping From Inside To Outside Host?
Jul 6, 2011configure my Cisco ASA5510 (asa version 8.3.1) so that one of the host (e.g.192.168.8.20) behind management interface can ping to the other host (e.g. 192.168.2.246) behind OUTSIDEinterface. I tried modifying the ACLs, NATs and ICMP statement, but still failed[CODE]
View 19 Replies View RelatedPing From Host To Guest With NAT?
Jun 27, 2012I have installed an Oracle DB (11.2) on a guest VM (Centos 5) and my host is Windows 7 Ultimate.I need to able to connect to the DB from windows.Ping status is as follows:
guest -> host - IP : Yes
guest -> host - hostname : Yes
guest -> guest - hostname : Yes
guest -> guest - IP : Yes
[code]....
Any Kind Of Equipment That Will Give Lower Ping For Online Gaming
Sep 30, 2012I have a 1.25 mbps download and .2 upload speed. I have a netgear n600 router and have wireless and cannot change to wired. I have around a 120 ping all most always. My current speed is the best in my area too. Is there any kind of equipment that will give me a lower ping for online gaming? Is there any router settings for this?
View 1 Replies View RelatedCisco WAN :: Cannot Get ASR 1002 To Ping On Interface To Host
May 12, 2013I have a cisco ASR 1002 I have plugged a host into an addressed port and the port comes up however the host cannot ping the router and the router cannot ping the host. Neither can router ping its self. I do the same on a cisco 2800 router and it works fine. What's goin on. Is it the fact that this is a ASR router ?
View 5 Replies View RelatedCisco :: 1140 APs - No Ping To Host From Local LAN
Apr 3, 2013I'm using 3 AP's 1140 with local authentication using local radius (flex connect mode).the radius server im using is MS 2008 R2.authentication is working great on all devices pc's&mobile.authentication method is PEAP wpa2 aes enterprise.after 3 or 4 hours devices loose connectivity to the web.the device seems to be still connected to the ap but there is no ping to host from local lan or any arp learnd on local router.only manual disconnect on device and reconnecting brings connectivity up again.in one case only reseting the AP's worked.
View 6 Replies View RelatedCisco Firewall :: ASA5505 - Can't Ping Inside Host
Sep 29, 2012I just try to ping a internal Host but it want to go.
Laptop<===>ASA5505
Connected is the Laptop at Ethernet 0/2 Inside
My running-config is a clear config, only VLAN 1 has a IP and Ethernet 0/2 is up.
But If I try to ping to the Laptop I get the followed:
asa5505# ping 192.168.1.100
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.100, timeout is 2 seconds:
?????
Success rate is 0 percent (0/5)
asa5505#
From the Laptop to the ASA5505 I can Ping successfully.
Cisco Firewall :: ASA5505 Cannot Ping Inside Host
Aug 2, 2011I have Cisco ASA 5505 installed and use as default gateway. I go to Internet through the ASA5505 Here is my Problem.I can not ping from ASA prompt(ASA#) to my Laptop connected to the ASA, but i can ping the ASA inside interface from laptop i can not use ASDM and the VPN Tunnel is not working between the sie
ASA# ping 10.10.10.12
???????????
100% lost
Laptop c
C:/ping 10.10.10.1
!!!!!!!!!!!!!!!!
Here is the Topology
INTERNET .<=========================>ASA<===============================> LAPTOP
I disabled window firewall on the Laptop , but no goof result.
Cisco Application :: 11503 Ping For One Virtual Host
Apr 27, 2013I have a single cisco 11503 load balancer.There is a single Banner student information system which is load balanced on it with Virtual ip 10.3.20.101 which is working fine without any issues .I am now trying to add an Oracle ERP application with virtual IP 10.3.20.230 and physical ips 10.3.19.22 and 10.3.19.23 all on port 8003.When I just make the group ERP-Apps-Grp active , the vitual ip address 10.3.20.230 is pingable , but when I make the the content Erp_IAT active it stops pinging. [code]
View 6 Replies View RelatedCisco Firewall :: ASA 5520 - PING From Outside Into Inside Host
May 13, 2013I have ASA 5520. I cannot ping the host(192.168.1.20) which is inside firewall from outside hosts. Inside host (192.168.1.20) is translated into (198.24.210.226) using static NAT.From outside host, I used "PING 198.24.210.226". Is it because I used dynamic PAT for inside hosts?
interface GigabitEthernet0/0nameif outsidesecurity-level 0ip address 198.24.210.230 255.255.255.248!interface GigabitEthernet0/1nameif insidesecurity-level 100ip address 192.168.1.1 255.255.255.0
[Code].....
Can't Ping / Connect Ipv6 Host On Windows 7 Vs XP
Apr 27, 2011When I try to ping ipv6.xsnews.nl on either of my Windows 7 computers, it returns "Ping request could not find host". But when I do it on XP, it succeeds. I have tried putting the W7 PC in the DMZ, disabling the software firewall but it doesn't work.
What I think it involves is having ipv6 installed on each. I tried to duplicate the setup of both the XP and a W7 computer, installing the gogo6 tunnel. But apparently it's not setup on this computer because the ping result is the same as on the third computer which hasn't had ipv6 installed. s not setup on this computer because the ping result is the same as on the third computer which hasn
Cisco Firewall :: NAT ASA 9.0(2) / Cannot Access Original IP Using Another Port Or Ping From Host
Apr 10, 2013Basically after upgrade from ASA 8.4 to 9.0 (2) I have problems when certain types of NAT.Example:SA 8.4: nat (LAN, outside) 85 10.252.253.123 source static 192.168.3.2 192.168.3.2 192.168.3.104 static destination service http http In this form the host 192.168.3.2 uses the mapped ip (192.168.3.104) to access by http while other ports can be accessed using the original IP (10.252.253.123).
ASA 9.0: nat (LAN, outside) 85 10.252.253.123 source static 192.168.3.2 192.168.3.2 192.168.3.104 static destination service http http In this form the host 192.168.3.2 uses the mapped ip (192.168.3.104) to access by http but unlike before now I cannot access to the original IP (10.252.253.123) using another port or ping from host 192.168.3.2.
Cisco WAN :: 1941w AP Can't Ping 2nd Router / Host But Interface Reachable
Feb 2, 2013From the router I can ping the 2nd router, all its host and all of the 1941w interfaces.
From the 1941w AP i cannot reach the 2nd router or any of its host, but I can reach the interface that is connected to the 2nd router but only one side of it.
Attached are both my router and ap configs. At the moment I am just trying to reach the 2nd router and its host so I can update the AP IOS image but cannot reach the tftp server.
Cisco VPN :: 2611xm - Unable To Ping Remote Host Through Tunnel?
Apr 20, 2012I am in a test environment using an ASA 55005 and a Cisoc 2611xm router. ASA is running version 8.4 and router is running is ios12.4. My VPN tunnel comes up but I am unable to ping between remote hosts. I used the ASDM and SDM for the configuration. Attached is a copy of both configs.
View 8 Replies View RelatedPing Could Not Find Host / DNS And Key-port / Server Not Found
Apr 30, 2011recently I had some malware on my Windows XP Professional (version 2002), so I followed a guide at Bleeping Computer [URL] to get rid of it. Problem is, for some reason, after I finished, I could no longer access the internet!When I try, FIrefox gives me their "could not connect" message: "Server not found. Firefox can't find the server at [site]." Check the address for typing errors such as ww.example.com instead of [URL]"When I try to log into MSN, the troubleshoot says I have a problem with my DNS and Key Ports.I'm not good with computers so I Google'd and found some ping-ing instructions. When I tried to ping [site], I get: "Ping request could not find host [site]. check the name and try again." This happens regardless of the site I use.Lastly, I tried "ping 127.0.0.1" from a troubleshooting site. It gives me: "Pinging 127.0.0.1 with 32 bytes of data:
Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
[code]..
Cisco Firewall :: Unable To Ping Host From Inside Interface From PIX525
Feb 3, 2012When I tried to upgrading PIX525 6.3 to 7.0 , Not able to Ping the host from the PIX 525 Inside interface which is on the same subnet, Also from the host to Inside Interface , Tried with Directly connected laptop with Cross cable and using Straight cable via switch, But the results end with fail.
View 2 Replies View RelatedRouters / Switches :: Ping 10.0.0.1 -t Give Destination Host Unreachable?
Mar 17, 2013ping 10.0.0.1 -t give me destination host unreachable in the same time when i wright ping 192.168.1.1 -t it give me the correct reply but the net doesnt work
View 3 Replies View RelatedPing - Destination Host Unreachable And Time To Live Exceeded
Oct 17, 2011when do we get Desteination host Unreachable and time to live exceeded while trying to ping .
From 10.1.1.1 icmp_seq=2 Destination Host Unreachable
From 10.1.1.1 icmp_seq=4 Destination Host Unreachable
From 10.1.1.1 icmp_seq=7 Destination Host Unreachable
Linksys Wireless Router :: WRT54G Unreachable Host And No Ping
Sep 26, 2011I've tried everything that has been posted so far except for opening up the router itself which I will refuse to do.- Getting = Host Unreachable 192.168.1.20 (I am using 192.168.1.1 as the gateway)- No ping whatsoever even when turning on the router over and over.
View 2 Replies View RelatedServers :: Ping Locally / Reply Successful - Destination Host Unreachable
Mar 4, 2011I am using the window server 2008 and configure tcp/ip properties correct ping locally reply successful when ping localy but when ping yahoo.com then reply destination host unreachable whereas gateway and dns ip is also correct configure so tell me solution about this problem because i am useing the internet.
View 1 Replies View RelatedCisco Switching/Routing :: 3560G Can Ping Devices In Enterprise LAN But Cannot Ping Interface
Mar 31, 2012I have a new 3560G to set up a small network for a remote site. I configured the vlan and an SVI as the gateway. The switch is also the DHCP server for the LAN. I configured Gi0/2 as L3 port, connecting to the nearest neighbor. My network runs EIGRP so i advertised the routes into the EIGRP process. The switch forms EIGRP neighbors and learns all routes in the enterprise network. The problems I'm having now are: 1. The switch learns all routes in my enterprise LAN and can ping devices in the enterprise LAN, but I can’t ping any interface on the switch from the enterprise LAN. 2.
View 5 Replies View Related