Ping Could Not Find Host / DNS And Key-port / Server Not Found
Apr 30, 2011
recently I had some malware on my Windows XP Professional (version 2002), so I followed a guide at Bleeping Computer [URL] to get rid of it. Problem is, for some reason, after I finished, I could no longer access the internet!When I try, FIrefox gives me their "could not connect" message: "Server not found. Firefox can't find the server at [site]." Check the address for typing errors such as ww.example.com instead of [URL]"When I try to log into MSN, the troubleshoot says I have a problem with my DNS and Key Ports.I'm not good with computers so I Google'd and found some ping-ing instructions. When I tried to ping [site], I get: "Ping request could not find host [site]. check the name and try again." This happens regardless of the site I use.Lastly, I tried "ping 127.0.0.1" from a troubleshooting site. It gives me: "Pinging 127.0.0.1 with 32 bytes of data:
Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
Basically after upgrade from ASA 8.4 to 9.0 (2) I have problems when certain types of NAT.Example:SA 8.4: nat (LAN, outside) 85 10.252.253.123 source static 192.168.3.2 192.168.3.2 192.168.3.104 static destination service http http In this form the host 192.168.3.2 uses the mapped ip (192.168.3.104) to access by http while other ports can be accessed using the original IP (10.252.253.123).
ASA 9.0: nat (LAN, outside) 85 10.252.253.123 source static 192.168.3.2 192.168.3.2 192.168.3.104 static destination service http http In this form the host 192.168.3.2 uses the mapped ip (192.168.3.104) to access by http but unlike before now I cannot access to the original IP (10.252.253.123) using another port or ping from host 192.168.3.2.
I have a host that can successfully connect to a PIX 515E (7.x OS) via VPN Client; however, I have no IP routing to the LAN from the remote host.The VPN IP pool works finem,The LAN default gateway is the inside interface on the PIX; the network is flat L2 behind it.The default route on the PIX points out; no other routes are defined,The VPN remote host can be pinged from LAN hosts, but the VPN remote host cannot ping any LAN host, not even the PIX inside interface.
I set this up and I can ping all the gateways but never the hosts. I was hoping I could make these links between 6500's a mix of L2 and L3. Check it out. They are connected in a linear fashion R1--->R2--->R3. I can ping from R1 to R3's SVI4 gateway but I can never ping a host on that SVI4. I was hoping that I could use the port-channels between 6500's as routed links or as trunk links depending on the type of traffic....thought it would ease the migration. I suppose I could always get rid of the port-channels and just make separate L2 and L3 links between the 6500's.
I found a bug in Embedded Event Manager, on Catalyst 4500-E platform with supervisor V-10GE, on various IOS releases (in particular 12.2-50-SG IP BASE w/o crypto, 12.2-54-SG1 IP BASE w/o crypto, but also other releases included latest 15.0-2-SG1 ENTERPRISE SERVICES SSH).The problem is that when you set up a EEM applet that monitors syslog pattern matching, and you also configure remote host logging *with* the option "sequence-num-session", when the match occurs, the switch reboots with message:
Sw (sometimes prints a number instead) VECTOR D00
and in some cases performs a second reboot with message:
VECTOR 0 DOUBLE FAULT
The reload reason message is:
System returned to ROM by abort at PC 0x0
The problem does *not* occur if remote logging has not the option "sequence-num-session". I verified this behavior on various configurations (included our production 130K long *and* factory defaults after erase startup-config).The configuration statements that cause reload are, for expample:
I have installed an Oracle DB (11.2) on a guest VM (Centos 5) and my host is Windows 7 Ultimate.I need to able to connect to the DB from windows.Ping status is as follows:
I'm going through the CCNA training and I'm setting up my DHCP server on my 871 router. I have my cable modem into the WAN port on my router and have 1 host plugged directly into Fastethernet 1. I can ping any IP I want from the IOS prompt but I only have local access from the host. [code]
I am having a major issue trying to connect my Windows 7 HP Netbook to my Xbox 360 over either Twonky/Serviio or Windows Media Centre. The Xbox just isn't picking up my computer, my homegroup recognises the Xbox and it is 'Allowed' to share media, but when I test my PC connection within the Xbox dashboard, it fails to connect to PC. My network is wireless.The strange thing is I have TwonkyServer Mobile running on my Android phone and that was found by my Xbox immediately with no need to change settings or search for devices. It streams media just fine from my phone. This leaves me thinking that it is an issue with my PC as opposed to my router, I have double checked my router settings (Sagem 2304), UPnP is showing as enabled, I've reset and unchecked/rechecked the UPnP but still not working.
My TwonkyMobileServer is also unable to find my PC server although I have been able to find my MobileServer in Windows Media Player and stream media from my phone.Windows Firewall has been disabled, I've also Uninstalled my antivirus software, Avast and AVG, although AVG doesn't seem to want to disappear that easily and is still lurking in my System Tray telling me i've 'Lost protection'...Norton Internet Security is also lurking around which is odd, I can not recall installing it! It doesn't seem to be a fully installed version and doesn't seem to want to be uninstalled. Could these AV software and supposed Internet Security software be holding me back?This leaves me thinking that my PC is holding back my Network. Is there any thing I haven't thought of? Would it be the Anti-virus leftovers ruining my streaming dreams??
I test all devices using ping command, from ASA to router was fine (on both interface) but not to Host , and host to router was fine, but only on directly interface(F1/0), and to ASA was not success. am i miss something in my configuration?
configure my Cisco ASA5510 (asa version 8.3.1) so that one of the host (e.g.192.168.8.20) behind management interface can ping to the other host (e.g. 192.168.2.246) behind OUTSIDEinterface. I tried modifying the ACLs, NATs and ICMP statement, but still failed[CODE]
When I try to ping ipv6.xsnews.nl on either of my Windows 7 computers, it returns "Ping request could not find host". But when I do it on XP, it succeeds. I have tried putting the W7 PC in the DMZ, disabling the software firewall but it doesn't work.
What I think it involves is having ipv6 installed on each. I tried to duplicate the setup of both the XP and a W7 computer, installing the gogo6 tunnel. But apparently it's not setup on this computer because the ping result is the same as on the third computer which hasn't had ipv6 installed. s not setup on this computer because the ping result is the same as on the third computer which hasn
I have a cisco ASR 1002 I have plugged a host into an addressed port and the port comes up however the host cannot ping the router and the router cannot ping the host. Neither can router ping its self. I do the same on a cisco 2800 router and it works fine. What's goin on. Is it the fact that this is a ASR router ?
I'm using 3 AP's 1140 with local authentication using local radius (flex connect mode).the radius server im using is MS 2008 R2.authentication is working great on all devices pc's&mobile.authentication method is PEAP wpa2 aes enterprise.after 3 or 4 hours devices loose connectivity to the web.the device seems to be still connected to the ap but there is no ping to host from local lan or any arp learnd on local router.only manual disconnect on device and reconnecting brings connectivity up again.in one case only reseting the AP's worked.
I have Cisco ASA 5505 installed and use as default gateway. I go to Internet through the ASA5505 Here is my Problem.I can not ping from ASA prompt(ASA#) to my Laptop connected to the ASA, but i can ping the ASA inside interface from laptop i can not use ASDM and the VPN Tunnel is not working between the sie
ASA# ping 10.10.10.12 ??????????? 100% lost Laptop c C:/ping 10.10.10.1 !!!!!!!!!!!!!!!!
Here is the Topology
INTERNET .<=========================>ASA<===============================> LAPTOP
I disabled window firewall on the Laptop , but no goof result.
I have a single cisco 11503 load balancer.There is a single Banner student information system which is load balanced on it with Virtual ip 10.3.20.101 which is working fine without any issues .I am now trying to add an Oracle ERP application with virtual IP 10.3.20.230 and physical ips 10.3.19.22 and 10.3.19.23 all on port 8003.When I just make the group ERP-Apps-Grp active , the vitual ip address 10.3.20.230 is pingable , but when I make the the content Erp_IAT active it stops pinging. [code]
I have ASA 5520. I cannot ping the host(192.168.1.20) which is inside firewall from outside hosts. Inside host (192.168.1.20) is translated into (198.24.210.226) using static NAT.From outside host, I used "PING 198.24.210.226". Is it because I used dynamic PAT for inside hosts?
ping 10.0.0.1 -t give me destination host unreachable in the same time when i wright ping 192.168.1.1 -t it give me the correct reply but the net doesnt work
I've tried everything that has been posted so far except for opening up the router itself which I will refuse to do.- Getting = Host Unreachable 192.168.1.20 (I am using 192.168.1.1 as the gateway)- No ping whatsoever even when turning on the router over and over.
From the router I can ping the 2nd router, all its host and all of the 1941w interfaces.
From the 1941w AP i cannot reach the 2nd router or any of its host, but I can reach the interface that is connected to the 2nd router but only one side of it.
Attached are both my router and ap configs. At the moment I am just trying to reach the 2nd router and its host so I can update the AP IOS image but cannot reach the tftp server.
I am in a test environment using an ASA 55005 and a Cisoc 2611xm router. ASA is running version 8.4 and router is running is ios12.4. My VPN tunnel comes up but I am unable to ping between remote hosts. I used the ASDM and SDM for the configuration. Attached is a copy of both configs.
I just bought pc anywhere software, after instalation in my host pc and laptop(remote) it work very well when I used it in the same network in my Rv camping ground where I have a mobil router with a Verizon broad band card.Later when I come back home where I have a cable internet with a router, I tried to access the host pc but after several minutes trying it said cant find host pc.
I am using the window server 2008 and configure tcp/ip properties correct ping locally reply successful when ping localy but when ping yahoo.com then reply destination host unreachable whereas gateway and dns ip is also correct configure so tell me solution about this problem because i am useing the internet.
When I tried to upgrading PIX525 6.3 to 7.0 , Not able to Ping the host from the PIX 525 Inside interface which is on the same subnet, Also from the host to Inside Interface , Tried with Directly connected laptop with Cross cable and using Straight cable via switch, But the results end with fail.
I've been wrestling with a Windows XP reinstall that wiped out my network adapter. Fortunately I found D-Link AirPlus Utility and have restored it. However, now it says that windows was unable to find a certificate to log me on to the network, although I have entered the correct key.
I installed window server 2003 in a old Pentium III server as a standalone test server. Now I want to use it as a print server and connected it to the domain. I can ping workstations and other servers from that test svr. But i cannot ping that test server from the work stations.
