Cisco WAN :: 887V VDSL Router / Pinging From The VLAN1?
Apr 7, 2011
I have a problem with my Cisco 887V VDSL-router. The router gets a ip-address with dhcp from my provider. That works fine. I also can ping from the router:
routerVdslTestNew#ping google.ch source vlan 1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 74.125.79.99, timeout is 2 seconds:
Packet sent with a source address of 10.10.10.1
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 48/48/52 ms
My problem: If I want to ping google from a computer in the VLAN1 the ping doesn't work.
C:UsersXXXXXX>ping 74.125.79.99
Ping wird ausgeführt für 74.125.79.99 mit 32 Bytes Daten:
Timeout.
View 3 Replies
ADVERTISEMENT
Apr 19, 2012
I've recently bought a new Cisco 877V-K9, but i've a problem with connecting. When powering up the modem only the "OK"-led is green, but the rest of the leds are off.
My computer is connected with FE0.
View 3 Replies
View Related
Oct 4, 2012
I have cisco 887V (CISCO887V-SEC-K9) router. I am not sure it will work as Access Point or not. It does not have any external antennas installed. I checked on website and found that all Cisco 887V routers have option of Access Point and also found that the software ap801-k9w7-tar.124-10b.JY.tar,can be used for access point.
View 1 Replies
View Related
Nov 25, 2011
I have a dir 655 coupled with a 320b modem for adsl. Now I must switch to VDSL. Can I use the router with a VDSL Modem? Which modem could be used ? I do not see dlink products ..
View 14 Replies
View Related
Sep 3, 2012
I have installed a CISCO v887 router in Amsterdam officeI established a VPN tunnel between AMS office and Edinburg office.
1. The VPN is up and running
2. I am unable to browse anything from LAN computers in Amsterdam office.
3. From LAN computers I can traceroute to yahoo.com but from browser I cant browse yahoo.com and web page hanged out in this situation (website found waiting for reply). But nothing comes over and LAN users are unable to use internet.
[code]...
View 11 Replies
View Related
Oct 20, 2012
I recently upgraded my DSL service, which required installing a new VDSL modem/wireless router (Actiontec c1000a.) Before the upgrade, I was using an older standalone DSL modem with a Netgear router to provide wireless access to my gaming consoles, laptop, etc. Everything works as before with my new wireless router EXCEPT my son's laptop. All my consoles, iPods, and desktop CAN connect to the wireless network, and the laptop will connect over a WIRED ethernet connection. I cannot get it to connect to the wifi.
[code]....
View 6 Replies
View Related
Nov 10, 2012
I desperately try to set up the X3000 as a router behind a vDSL modem. When I choose connection through Ethernet and then PPPoE, it never keep the credentials after reboot in spite of having saved the data before.
View 6 Replies
View Related
Jan 24, 2013
I have a Dell Aspire 5332 laptop and i haven't used it since November 2012 (where it was working fine).It had Windows updates when i switched it off. I switched it on today and i have no internet connection. When hovering over the icon it says unidentified network - no internet access. My service provider is British Telecom and i am on the Fibre Optic package. I am using the BT Home Hub 2.0.Fibre Type B and also a Echolife HG 612 model FTCC VDSL NTE Router. I have Norton installed on the machine but there is only 1 day left on the subscription. I have tried a wired connection from the router but still have the same message. 2 other computers are wired to the router and all of our Ipads and Macbook connect wirelessly with no problems.
View 19 Replies
View Related
Sep 20, 2011
Lately I've noticed that my internet connection has been less than stellar. I will be playing an online game or surfing the web, and every so often I'll freeze up or things just won't run smoothly. My network consists of the following...All of my computers and devices connect to a Cisco 16 port gigabit switchThe switch then connects to a Peplink 20 Dual WAN routerThe router connects to a cable modem as well as a DSL modemThe other day I was trying to diagnose the problem, as well as update the firmware of the router. While I was on the main "status" page, I noticed an error saying that I couldn't connect to the router. It quickly cleared and everything was working fine. This of course made me think that my issues have to do with my connection to the router, and not with the internet service itself. I then tried ping -t to two other computers on the network, as well as the router. After 5 minutes of pinging, the connections to the two computers had zero fails, while the router connection failed about 5% of the time. I ran the same check from the other computers on the network, with similar results.So, I know that the issue lies with the router (I think), but that's where my brainstorm ends.
View 4 Replies
View Related
Oct 3, 2012
Lost Internet connectivity at home. connected via dsl line to my isp.when i issued ipconfig /all command i noticed that default gateway IP addr was a global ip addr. (77.36.x.x) instead of the usual private address 192.168.1.1. DHCP server had IP address 58.206.x.x when i issued ping 192.168.1.1 command, i got this output: "reply from 77.36.x.x: destination host unreachable" i couldn't access my router's configuration menu by typing 192.168.1.1 in web browser's address field.it's very interesting, because i had network issues before but could access my router's config menu and ping it. but now, i cannot reach my local router but receive reply from ISP's router.
View 10 Replies
View Related
Oct 12, 2012
In my preparation for my coming CCNA certification I am experimenting with different network configurations. In my test network I am currently working with a "Router on a stick" setup. A Cisco 2611 router connecting a Cisco 2950 switch. VLANs configured on the switch and subinterfaces + dot1q encapsulation configured on the router. Switch only supports dot1q.Router's Eth0/1 is connected to the Switch Fa0/24 port which is also set to trunk mode. I am using a normal Cat5e twisted pair cable to connect the 2 devices.
VLANs are working since I can connect a workstation to an access port for example fa0/2 (vlan2) and get Internet access.I can also ping any of the subinterfaces of the router from the workstation.With the current setup I am not able to ping the switch from the router, or the other way around, so in other words I can't remote manage the switch from a telnet or SSH session with this setup. What I am missing?Just to be clear I am pinging the switch directly from the router (Router2611#ping 172.16.100.2), so please ignore all static routes and OSPF. [code]
View 3 Replies
View Related
Mar 12, 2012
One of my laptops is having a connection problem. I have 3 other laptops that can connect perfectly with my router, and normally there's only 1 laptop that is connected to my router. The laptop with the slow connection (takes 5 HOURS to load a website, sometimes will not even load), i re-installed the OS, and installed all the drivers needed, and it still wont work. it shows strong connection to me, and im sure the password for the router is right. below is the ipconfig/all information. Having this problem for 2+ weeks now!!! I think this problem started when i restored my router to factory setting, my router is Netgear WGR614v6.
View 14 Replies
View Related
Feb 15, 2011
I have configured the "ISP" part of the VDSL as i am a tech for the ISP that has access to this, but i am not able to get my 887V to synch is there something i am doing wrong within the Cisco, i have included a debug and couple more things. [Code] ....
View 3 Replies
View Related
Feb 3, 2013
I'm trying to get a catalyst going for remote management using cisco network assistant.I've basically, enabled telnet;
enable conf t line vty 0 15 password {password}
login
exit
gave it an IP;
int vlan1 ip address {IP} {Subnet}
no shutdown
exit
[code]...
and write mem to save it all. I can ping, telnet and access cisco network assistant from inside the network perfectly. But the problem I'm having is accessing it from outside, can't even ping the device. I can ssh to other servers behind the network just fine. There is no firewall in place at the moment, the provider's drop is plugged in gige port 1?
View 3 Replies
View Related
Nov 25, 2011
I'm trying to get an internet connection through my cisco 877va but I can't get access. I can see DSL up, however, the dialer0 interface can't get access to internet. Here is my configuration:
[code].....
View 2 Replies
View Related
Dec 27, 2009
In default mode the ASA 5505 is setup with two Vlan's, one inside and one outside. Vlan1 is the default inside VLan, with IP 192.168.1.1. I would like to change the subnet of Vlan1 tot 192.168.10.1, but when I do, no Ethernet port is assigned to Vlan1 anymore (was 0/1 - 0/7). What I have done is;
#config t
(config)#interface vlan 1
(config)#ip address 192.168.10.1 255.255.255.0
But after that, no Ethernet port is within Vlan1, so I tried the following to assign one (port 0/1);
#config t
(config)#interface 0/1
(config)#switchport access vlan 1
(config)#no shut
But nothing happends when monitoring (#show run) interface 0/1 (no Vlan assigned)
View 6 Replies
View Related
Jun 17, 2012
I'm facing an issue since 2 month now , no one is able to tell me what's going on. The line goes down suddently for 2 or 3 minutes and this happens everyday at the same range (~2 or 3 hours) of time . I don't have any scheduled task to cause this. ISP in his side has also made some tshoot but found nothing and is convinced that the problem is coming from our side :
Here is some log :
Cisco IOS Software, C880 Software (C880DATA-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
rtr-Id#show debugging
Generic IP:
IP packet errors debugging is on
IP NAT ERROR debugging is on
PPP:
[Code]...
View 3 Replies
View Related
Nov 13, 2012
I have the following topology:
2x 877 routers, one interface from each router (port Fa0 which belongs to the router internal switch) is connected to the 2960 switch, the switch himself configured with default settings, flat with one v LAN.
I have configured HSRP in the following manner: router A is 10.0.0.2, router B is 10.0.0.3, virtual IP is 10.0.0.1, take note that the HSRP configuration along with the IP address are configured on vlan1 interface.
Now when i connect a PC to the switch with static IP (10.0.0.4) and trying to ping 10.0.0.1 I'm not getting replies. i see on the PC, using wire shark, the icmp request goes out but on the primary router (and also on the backup) i can't see the icmp request (using debug ip icmp).
this behavior happens only when the HSRP is configured on interface vlan1, when configuring the same configuration on Fa4 (which is WAN interface) everything works fine.
View 4 Replies
View Related
Aug 8, 2011
I will install in the next days a 886VA router (VDSL over ISDN using PPoE). Since I have no possibility to verify the VDSL config, this is what i prepared. Is this config OK (only VDSL part) ?
controller vdsl 0
operating mode auto
interface Ethernet0
[ code]...
For VDSL over ISDN the interface Ethernet0 must be used instead of ATM . Is this config correct ?
View 5 Replies
View Related
Jan 20, 2013
Everything in my network works as a charm. Every host in my vlans can access and ping the internet with no problems. But, my main router does not ping the internet (Pinging either ip "173.194.71.104" or domain "www.google.com" do not work). I don't know how is that possible since my hosts can ping the internet. Below is my main router confiurations
!
hostname Internet_Router
!
boot-start-marker
[Code].....
View 16 Replies
View Related
Aug 24, 2012
Just got hold of my first 887va for my home, never configured a vdsl interface before and was just wondering if my setup looked good to someone whos done it a few times.
View 6 Replies
View Related
Feb 26, 2012
I have an ASA5505 where vlan1 (inside) and all associated ports (e0/1 - e0/7) are down. Workstations on vlan 1 are online and working. Vlan2 (outside) is up and running normally. I tried to shut/no shut on the vlan. I also rebooted the firewall. No change. Why vlan1 is down?? I've attached some config info and some troubleshooting.
View 5 Replies
View Related
Mar 17, 2013
I want to dumb down a Cisco 886va to act as a pure vdsl bridge modem with a local ip to be able to do some admin work on the router. To some extent my config works, but i think the default vlan 1 kills my internet. When i connect the 88va the vlan bridge 7 and 8 goes up, the router behind connects via pppoe on vlan 7 but no traffic is going through. vlan 8 gets a dhcp lease for iptv and if i don´t switch the receiver on and off the traffic flows and the tv works. I am also able to connect to the local ip to access the web interface. [code]
View 1 Replies
View Related
May 20, 2013
I want to know how am i do to change the Vlan1`s IP address because the actual ip will be used in another vlan. Actually i haver 10 vlans in L3 mode (routing) implemented in it.
View 5 Replies
View Related
May 12, 2013
router 1721 with one wic-1adsl ,i have adsl conection with irb static ip. the router connect with mannaged switch through a trunk port. the switch has 2 vlans one for the static IPs and the other for private lan. i need the private lan to be able to go to internet. vlan2 can go to internet because it has the same subnet with provider but vlan 1 canot go internet, so how i can make all vlans go internet(the router has only 1 fastethernet port)
View 4 Replies
View Related
Sep 19, 2011
I'm trying to upgrade the VDSL firmware on a 887VA. I've uploaded the file vdsl.bin-A2pv6C035d_d23j to the router. I understand this file has to be renamed with a .bin extension in order to be recognized after a reboot, but the attempts I have made have not worked. What must this file be renamed to in order to load the new firmware into the VDSL controller?
Here is the current firmware information. I've tried several of the obvious file names.
Firmware Source File Name (version)-------- ------ -------------------VDSL embedded VDSL_LINUX_DEV_01212008 (1)
Modem FW Version: 110331_1212-4.02L.03.A2pv6C032b.d23fModem PHY Version: A2pv6C032b.d23f
View 1 Replies
View Related
Mar 13, 2013
Trying to get my 887va setup for VDSL but can't get to anything on the net -
Controller VDSL 0vpdn enablevpdn-group 1
interface ethernet0
no ip address
[Code].....
View 6 Replies
View Related
Mar 26, 2012
I am trying to design a network for our block of 20 apartments. The WAN supplies Ultima at up to 40 mb/s and the takeup on LAN is anticipated to be modest. However I have been told that two residents operate non commercial web sites currently on stand alone adsl with ddns. The netgear router supplied by the ISP obviously has port forwarding but how do I differentiate for traffic on port 80?
View 1 Replies
View Related
Jun 4, 2012
Got an odd problem with trunking, all vlans except vlan1 trunk perfectly. Link is from a pair of dualhomed FEX 2248TP's to some 3650G Switches. Nexus running - version 5.1(3)N2(1) 3560's running - 12.2(53)SE2 & 15.0(1)SE2
View 3 Replies
View Related
Jan 16, 2012
I have a problem where only the 2950's switches go transperant. They drop VLAN1 thus no CDP snmp packets. The users keep working fine but our NMS center keeps calling me at 3am when this happens.
These are access switches that connect to stacked 3750's. Some of the uplinks are using media converters that i have been trying to get removed. But i doubt that it could be the cause of the vlan1 going down.
View 3 Replies
View Related
Apr 25, 2013
I just bought a 5505 to learn from and am trying to attach my VDSL modem as a transparent bridge.It goes....
Laptop >>> (VLAN1) Cisco 5505 (VLAN2) >>> VDSL modem >>> internet
X.X.X.10 >>> (X.X.X.254) ------ (Y.Y.Y.254) >>> Y.Y.Y.10 >>> A.B.C.D.
I'm using the ASDM, if I configure VLAN2 with the IP address of the VDSL interface I can ping the modem from the console session via Putty. If I take that off and configure up the PPPOE client I can't ping the VDSL modem, I'd expect that. If I then add in an IP address to the PPPOE client config like I assigned to VLAN2 it doesn't ping either.If I can't ping the VDSL modem I don't expect it would work but it seems I can only either give it a static address which pings but has no pppoe or give it a PPPOE config which means I can't ping the VDSL. why I can't ping the VDSL modem when the interface is set as PPPOE with an IP address?Presumably if I'm on the ASA console doing pings from there to the modem then I'm ruling out problems with the routing from the laptop (trying to isolate where the issue is)
View 3 Replies
View Related
Apr 28, 2013
what enhancements, fixes, etc are included in the Cisco 887VA VDSL firmware version A2pv6C035l.d23j, relased 29-MAR-2013.I can't seem to find any release notes with this firmware.We are using version A2pv6C035d.d23j firmware on around 150 887VA's on BT ADSL lines, and was looking for any improvements this version may offer.
View 1 Replies
View Related
Nov 19, 2011
I have 2 VLANs set up and I know they are set as default to not allow one to communicate to the other. Is there a way to set a rule to allow that? I'd like VLAN1 to be able to access VLAN2, but not the other way around.
View 1 Replies
View Related
