Cisco Switching/Routing :: Internet Router (2901) Is Not Pinging The Internet
Jan 20, 2013
Everything in my network works as a charm. Every host in my vlans can access and ping the internet with no problems. But, my main router does not ping the internet (Pinging either ip "173.194.71.104" or domain "www.google.com" do not work). I don't know how is that possible since my hosts can ping the internet. Below is my main router confiurations
!
hostname Internet_Router
!
boot-start-marker
[Code].....
View 16 Replies
ADVERTISEMENT
Oct 12, 2012
In my preparation for my coming CCNA certification I am experimenting with different network configurations. In my test network I am currently working with a "Router on a stick" setup. A Cisco 2611 router connecting a Cisco 2950 switch. VLANs configured on the switch and subinterfaces + dot1q encapsulation configured on the router. Switch only supports dot1q.Router's Eth0/1 is connected to the Switch Fa0/24 port which is also set to trunk mode. I am using a normal Cat5e twisted pair cable to connect the 2 devices.
VLANs are working since I can connect a workstation to an access port for example fa0/2 (vlan2) and get Internet access.I can also ping any of the subinterfaces of the router from the workstation.With the current setup I am not able to ping the switch from the router, or the other way around, so in other words I can't remote manage the switch from a telnet or SSH session with this setup. What I am missing?Just to be clear I am pinging the switch directly from the router (Router2611#ping 172.16.100.2), so please ignore all static routes and OSPF. [code]
View 3 Replies
View Related
Mar 12, 2012
One of my laptops is having a connection problem. I have 3 other laptops that can connect perfectly with my router, and normally there's only 1 laptop that is connected to my router. The laptop with the slow connection (takes 5 HOURS to load a website, sometimes will not even load), i re-installed the OS, and installed all the drivers needed, and it still wont work. it shows strong connection to me, and im sure the password for the router is right. below is the ipconfig/all information. Having this problem for 2+ weeks now!!! I think this problem started when i restored my router to factory setting, my router is Netgear WGR614v6.
View 14 Replies
View Related
Feb 18, 2013
I need to break into a 2901 router to recover the passwords. Cisco's methodology for password recovery on 2900 seriews routerssays to remove the compact flash card and reboot into RMON. There is no external compact flash card on a 2901. Is there acompact flash card inside the box? Or can you use the older method of rebooting and then hitting ctl+break to boot into RMON?
View 5 Replies
View Related
May 2, 2012
i'm interested if it's possible to set the NTP server via DHCP on an 2901 Router with 15.2(2) image.
i configured the interface gigabit 0/0 as dhcp client. The DHCP Server sends to me DNS, Default GW and NTP. All is working fine, but the NTP will not be configured. i tried to add an DHCP option request, but there is no NTP (42) value. [code]
is there any way to add the value NTP (42) for the DHCP request or isnt it possible?
View 4 Replies
View Related
Dec 5, 2011
i want to use the cisco 2901 router with two adsl cards(EHWIC-VA-DSL-B) and would like to know if that possible without any restrictions with the ip base license.
View 2 Replies
View Related
May 1, 2012
I am have 3 machines int he house connected to the internet but one does not have internet access. It shows connected to the wireless network and from the command prompt there is an ip assigned to the laptop. But i cannot ping the gateway or any ip I get General Failure.
View 1 Replies
View Related
May 29, 2013
I am getting RTO while pinging my L3 switch 3750 that happened after restarting switch,i have restarted it because I am not able to browse internet through URL,i am able to do it trough ip address, so I restarted it not I am getting RTO.
View 1 Replies
View Related
Apr 30, 2012
I have an Issue.In my networks, 1 single user is facing Network Slowness issue. i needs to check to which port user is coneected in switch to CHeck whether that port has any errors.But problem is, i am providing support from remote location.And my concern LAN segment is Very big,I have only user Ip address details,when i ping the Ip address from Core switch it is pinging. but when i give show ip arp & give Ip address then its not learning and listing out the Mac address to trace down to the specific port.
View 3 Replies
View Related
Nov 1, 2011
We have a Cisco 3640 router running c3640-is-mz.123-3g.bin Switching ports are devided into several VLans. Each VLan has its own IP subnet. We can't ping IP address X in subnet A from subnet B unless we log into the router and ping it from there first. (and then the IP address will show up in "show ip arp" command. Then we can ping X in subnet A from subnet B, and browse web on device X from subnet B, etc. )
View 6 Replies
View Related
Aug 4, 2012
last day i went to one client for the installation of C(WS-C4507R+E)
current ios :cat4500e-ipbase-mz.122-53.SG2.bin
there is only one sup engine installed and redundant slot is empty.
I installed one ethernet module in the slot 6 and it get detected working fine. I also want to install one fiber module but that module is only supported by 12.2 54 sg or later ios version.so i need an ios upgrade.
For the ios upgrade I decide to do it through svi interface For that i igive an ip address to vlan 1 (192.168.1.2) and plug cable in gigabit 6/1 and added that port into valn 1.
my laptop's ip is 192.168.1.1 @ this point i faced a rare problem the PING IS NOT WORKING.(switch is directly connected to my laptop).
Then i create another VLAN (2) and add that port into vlan 2 still ping is not getting.last thing i tried is that making that gigabit port into a routed port and result is same.
View 4 Replies
View Related
Feb 2, 2012
I'm having an issue routing between vlans. I have vlan 1, and 2. I want to ping something on vlan 2, from vlan 1. I cannot ping from a computer on vlan 1 to a computer on vlan 2. I can ping each computer from the ASA 5505. I get an error on the ASA when I try to ping from the computers. The error is Failed to locate egress interface for UDP from voice:192.168.0.199/137 to 192.168.1.200/137. I can't understand why it even mentions IP 192.168. 1.200/ 137... I reset the unit configuring it from scratch and still no go. I have no given a static route to the out yet.. I need to get inter-vlan routing working first. [code]
View 13 Replies
View Related
Feb 4, 2013
i configured the VLAN810, with DHCP services, while i try to ping the host which is connected to gi 1/0/2 from my gi 1/0/1 , i can't ping the same vlan host , while i try to debug ip icmp its showing ,
C3750XB11#sh running-config
Building configuration...
Current configuration : 12053 bytes
!
version 12.2
no service pad
service timestamps debug datetime msec
[code]....
View 5 Replies
View Related
Jan 1, 2012
Physical devices are a Cisco 2901 (CISCO2901/K9) with GE0/0 configured as 192.168.1.1
Connected through a D-Link DGS-1210-24 configured as 192.168.1.202
Running on a domain with an HP domain server as 192.168.1.2
The 2901 was an EHWIC (VA-DSL-A oPoTS) on EHWIC 0/0/0
GE 0/0 on the 2901 is physically connected to the DGS-1210 which is physically connected to the server.
VDSL 0/0/0 is physically connected to the DSL jack.
So far the configuration reports all is connected, and I can ping the gateway of our ISP (using CLI or Cisco CP); however the server reports no internet connection and no workstations can access the 'net.
Once connected; I'd also like to allow ports through for use on the network (25, 80, 110, 443, 987, 1723) - but not sure on how to do that just yet!
Our IP is 202.27.19x.19x
Our Gateway is 202.27.217.5
[Code] ......
View 11 Replies
View Related
Jun 2, 2012
Why I cant correctly use ip sla command. I only have on my 2901 such commands: ip sla ?
key-chain Use MD5 Authentication for IP SLAs Control Messages
responder Enable IP SLAs Responder
server IPPM server configuration
There is my "sh ver"
ROM: System Bootstrap, Version 15.0(1r)M15, RELEASE SOFTWARE (fc1)
And...What should i do. if i want to create a failover with to WANs
View 2 Replies
View Related
Jan 10, 2013
I need another set of eyes on my config. I am trying to set up my router for a basic connection for the time being. I set my gig 0/0 port to dhcp I see traffic being sent and recieved but I can not ping 8.8.8.8. I am connected to a basic comcast modem from 0/0 I have also tried setting gig 0/0 to 100 full. I do have IP routing enabled. I believe I have my acl's configured correctly. I am wondering at this point if I need a static block of IP's from comcast.
hostname vpn-router-2901
username ****** password *****
enable secret *****
[Code].....
View 14 Replies
View Related
Mar 10, 2012
I am attempting to configure a Cisco 2901 router using IOS 15 to properly perform NAT/PAT translation between LAN and the internet connection.
My Configuration:
interface GigabitEthernet0/0
ip address dhcp
ip nat outside
ip virtual-reassembly
no ip route-cache
duplex auto
speed auto
no cdp enable
no mop enabled(code)
View 28 Replies
View Related
Jan 15, 2012
I have a subnet for guest network access, both wired and wireless. We have a Netgear ProSafe that is trunked to a Cisco 2901 performing 'Router-on-a-Stick'. For most internal traffic, it all stays behind the ASA. But for guest traffic, I have a route-map that sets the next-hop address as the outside interface of the ASA. The question is, how can I still permit those users to access our internal DNS servers? Do I need any particular NAT translations, exemptions, DNS doctoring, hairpinning, etc.? I have an ACL on the inside interface that permits traffic from the guest networks to our internal DNS servers, and then the next ACL line denies any other traffic from the guest networks to any of our internal networks.
View 7 Replies
View Related
Feb 3, 2013
I am trying to implement an etherchannel on a cisco 2901 (IOS 15.1). i have already created the port-channel but i cannot assign the gig interface to the channel group.
View 1 Replies
View Related
Jun 6, 2013
I recently installed a cisco 2901 router. The router is connected to hosts using a SG 200-50 50-Port Gigabit Smart Switch
Problem is the router internal interface keeps shutting down without notice and randomly. At that time I cannot ping the interrface from a LAN PC even though I can ping other hosts on the LAN. The ISP link is okay since I can put a static IP on my computer and access the net.
View 8 Replies
View Related
Jun 10, 2013
Does the 2901 have etherchannel capabilities? If so, how to configure it? I mean, I can type "show etherchannel 1" in it, so I would assume if I can show it, I better be able to configure it, right?What about the 2911?
View 1 Replies
View Related
Jun 29, 2012
I have a Cisco 2901 with the 4port gigabit ethernet switch module that I'm trying to get configured to have a seperate subnet for each port. So far I have it set up so each subnet is a vlan, then on each port I use the switchport access vlan command to tell it which subnet I want that port to be on. However, there is one port that I need to have 2 subnets on. The way I found to do that was to use switchport trunking on that port, but it doesn't seem to be working properly. how they would configure this? Right now I have vlan 101 as x.x.x.17/28 and vlan 103 as x.x.x.53/30. I think where I'm getting hung up is the proper association between the physical port and the vlan subnets.
View 5 Replies
View Related
Jul 26, 2012
I have always done my port monitoring (SPAN) on Cisco layer 3 switches with no issues. This time I am trying to do this on a Cisco 2901 router:
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M2, RELEASE SOFTWARE (fc1)
System image file is "flash0:c2900-universalk9-mz.SPA.151-4.M2.bin
I need to have the source port gig0/0 and destination port gig0/1. There is something about the gig port enumeration (slot/port#) that makes the command rejected. It is self explanatory:
#sh ip int brie
Interface IP-Address OK? Method Status Protocol
Embedded-Service-Engine0/0 unassigned YES NVRAM administratively down down
GigabitEthernet0/0 xxx.xxx.xxx.xxx YES NVRAM up up
GigabitEthernet0/1 unassigned YES NVRAM up up
Serial0/0/0:0 unassigned YES unset up up
[code]....
It doesn't matter what slot or port number I use, it is always rejected. The command is rejected for Both destination and source gig interfaces. I tried a wide variety of slot/port numbers. To my best understanding the complete port names are: GigabitEthernet0/0 and GigabitEthernet0/1, so why does it think there has to be another digit after 0/0 or 0/1? Does it have anything to do with the Embedded-Service-Engine0/0 being administratively down?
View 4 Replies
View Related
Mar 12, 2012
I am having an issue accessing the internet from a PC on the LAN. I have configured the PC with the gateway of the router infront of the ISP to test. I can ping from the router to google or any other internet IP. From the PC I can ping to the GIG0/1 (Inside LAN IP) and the GIG0/0 (Outside WAN IP going to ISP) but I can't ping the Next Hop IP of the ISP or anything past that. If I do a trace route from the PC to the google IP address it hits the GIG0/1 Inside LAN IP Address but fails from there. Here is a cut down snap shot of the router configure
[code]....
View 6 Replies
View Related
Jan 29, 2012
We have a new internet connection from DSL cisco router 800 Series (877).
You has been delivered it to us with Cisco Router 800 series (Ver 877), when we connect it to the PC directly it’ll work fine with the static IP.
We configured the OSPF between the Switch and the Router. and we can reach to the DSL router IP from our LAN any where. but we can't exit from the router to the internet.
DSL router 877 ---------------> Core Switch 6509 ----> PC
Router 877 (DSL):
-----------------
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
[code]....
View 5 Replies
View Related
Jan 21, 2013
I'm currently undergoing CCNa academy so I got a "job" from my boss to configure Cisco 871 router. Unfortunately we just finished first semester at academy so there are some things that I'm still having hard time to understand. I managed to configure router so it connect to internet or to be exact it has internet access through another adsl modem that is in bridge mode. url...The problem is that users are not able to use internet when connected to this router. I'm able to access router through telnet ( ip 192.168.13.10) but that's it.192.168.13.0 255.255.255.128 is network that we use at work. 192.168.13.5 is IP address that is assigned to zyxel adsl modem ( If I'm correct, we could have used any address here since we are connecting this directly to router ? ) Zyxel adsl modem is connected to FA4 port on Cisco router. LAN cable is connected to FA0 port and from there it goes to switch ( it's some asus switch with 50 ports). [code]
If I ping google dns from router e.g. ping 8.8.8.8 it works. If I ping url... it doesn't work. Also I'm able to access router via 192.168.13.10 but if I use router as default gateway then I'm not able to access the internet.
View 8 Replies
View Related
Aug 31, 2012
I have a Cisco 2811 Router with a NM-16ESW card installed. I've connected this to my DSL connecting and I'm trying to build myself a learning lab. From the router I can ping to the internet and back to a test computer I have connected to one of the card's ethernet ports. From the test computer, I can ping the router's WAN interface, but no further. [code]
View 10 Replies
View Related
Jul 21, 2012
I have a new 861 router which I have connected to my home broadband cable modem. Got it all working okay and I have access to the Internet but its not as fast as it is if I connect my laptop to the modem.
My Internet is 60mb (was 100 but I downgraded). When I cannot my laptop directly to the cable modem, I get 60mb download speed on speedtest.net If I connect the router's WAN port back to the modem then I roughly get about 40mb, sometimes even 50.
I do not have any IOS firewall configured on the router, just basic ACLs to stop SSH and TELNET from public networks. If I do enable firewall then my Internet connection halves itself. I have read around that this is the case with ios firewalls on these small routers so I've disabled the firewall but I still don't know why I cannot get full Internet speed.
View 5 Replies
View Related
Jan 6, 2012
I have the following devices for our IT Test LAB
1. Cisco 1841 with 2 Fast Ethernet interfaces fa0/0 & fa0/1
2. Cisco 2960-S
3. Speedstream 6200 DSL Modem ( PPOE Connection with Static IP address)
I want to connect to the internet using the current DSL connection we currently have .
LAPTOP --> SWITCH 2960 --> ROUTER 1841 ---> DSL Modem ---> ISP
Troubleshooting 1: Currently from the LAPTOP i am able to ping
1. Switch 2960 Vlan interfaces
2. Router 1841 fa0/0 & fa0/1
BUT can not Ping the DSL Modem LAN interface IP 192.168.2.1 and can not get out to the INTERNET
Troubleshooting 2:currently from the Switch 2960 i can ping
1. All the Vlan interfaces on the Switch 2960
2. Router 1841 fa0/0 & fa0/1 interfaces
3. Laptop A & B
But can NOT ping the DSL modem LAN interface IP 192.168.2.1 and can not get out to the internet
Troubleshooting 3:Currently from the Cisco 1841 router i can ping
1. All the Vlan interfaces on the Switch 2960
2. Router 1841 fa0/0 & fa0/1
3. Laptop A & Laptop B
4. Can Get out to the internet. I am able to ping any internet destinations without any problem
View 10 Replies
View Related
Feb 11, 2013
I want to set up my LAN to have internet access via my 2801 router.The 2801 router is connected to my home ADSL router.Now do I just configure a 0.0.0.0 'gateway of last resort' on the 2801 router pointing to the interface leading to the ADSL router ?Therefore, all traffic from my PCs that is internet bound will head out to the ADSL router and onto the internet.
View 3 Replies
View Related
Nov 21, 2012
the cisco 2921 Router has a default ip hhtp access class command found in it. Just i changed the default IP to the new ip i will use.The Router is accessable from the LAN only but not from the internet configured the Public ip . I think this is due to the standard access list 23 . how will i access the Router from the Internet using the Public IP.
View 6 Replies
View Related
Nov 2, 2011
I want to know is it possible to check Internet speed directly in the cisco router thru any command or activating any service in the cisco router?.As it is seen most of the times internet speed offer by ISP is different as compared to clients.and Clients most oftenly not satisfied with internet speed The problem is that our ISP has given us 100MB leaased line.But when we deployed in production network the speed is same as DSL.We have reported this issue to ISP they then carried out Iperf test by connecting laptop directly with the ISP router.They have tested the speed and it shows about 94-96 Mbps and argu that it is up to the mark and there is problem at your side(i.e our internal network).Now our internal network has cisco 1841 router connected directly to ISP 3825 cisco router.Our router has minimum configuration as required to pass traffic out and in.Our internal 1841 router is connected to switch to which different clients are connected.We have performed some online tests using different speed checking websites and also perform real time tests by uploading and downloading files.The speed is much low as compared to 100Mbps and it is nearly or slightly higher then as DSL connection. how can we check internet speed in the specified scenario?Is there any command or service available in cisco router to check internet speed as we want to check ISP connection speed directly thru 1841 router?what about authenticity of online speed checking websites?Any specialize software/tool you recommend to check Internet speed in specified scenario?
View 11 Replies
View Related
Sep 8, 2012
I am with Virgin media and have a home lab (2611 routers, 3550 switches, 2950s etc) which i usually just use for testing things on and practicing.
Now I tried to connect it to the internet and got some weird things happening.
I got NAT and DHCP client all setup correctly on the router (or so I think!) along with DNS settings but I still can't get Internet access.
My network is all setup right so that through using OSPF the router is the gateway (0.0.0.0 route) for all devices. Doing a traceroute confirms this.
Yet I never get any further than the router? I see IP nat translations ticking up as I send more requests but never get a webpage or a reply from any of the machines in my network.
HOWEVER... The router itself does get some replies from Google.co.uk and bbc.co.uk but doesn't seem to want to give anything else on the "inside" a response?
Here is a dump of config:
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
[Code].....
View 11 Replies
View Related
