I am getting RTO while pinging my L3 switch 3750 that happened after restarting switch,i have restarted it because I am not able to browse internet through URL,i am able to do it trough ip address, so I restarted it not I am getting RTO.
View 1 Replies
I have an Issue.In my networks, 1 single user is facing Network Slowness issue. i needs to check to which port user is coneected in switch to CHeck whether that port has any errors.But problem is, i am providing support from remote location.And my concern LAN segment is Very big,I have only user Ip address details,when i ping the Ip address from Core switch it is pinging. but when i give show ip arp & give Ip address then its not learning and listing out the Mac address to trace down to the specific port.
View 3 Replies View RelatedWe have a Cisco 3640 router running c3640-is-mz.123-3g.bin Switching ports are devided into several VLans. Each VLan has its own IP subnet. We can't ping IP address X in subnet A from subnet B unless we log into the router and ping it from there first. (and then the IP address will show up in "show ip arp" command. Then we can ping X in subnet A from subnet B, and browse web on device X from subnet B, etc. )
View 6 Replies View Relatedlast day i went to one client for the installation of C(WS-C4507R+E)
current ios :cat4500e-ipbase-mz.122-53.SG2.bin
there is only one sup engine installed and redundant slot is empty.
I installed one ethernet module in the slot 6 and it get detected working fine. I also want to install one fiber module but that module is only supported by 12.2 54 sg or later ios version.so i need an ios upgrade.
For the ios upgrade I decide to do it through svi interface For that i igive an ip address to vlan 1 (192.168.1.2) and plug cable in gigabit 6/1 and added that port into valn 1.
my laptop's ip is 192.168.1.1 @ this point i faced a rare problem the PING IS NOT WORKING.(switch is directly connected to my laptop).
Then i create another VLAN (2) and add that port into vlan 2 still ping is not getting.last thing i tried is that making that gigabit port into a routed port and result is same.
I'm having an issue routing between vlans. I have vlan 1, and 2. I want to ping something on vlan 2, from vlan 1. I cannot ping from a computer on vlan 1 to a computer on vlan 2. I can ping each computer from the ASA 5505. I get an error on the ASA when I try to ping from the computers. The error is Failed to locate egress interface for UDP from voice:192.168.0.199/137 to 192.168.1.200/137. I can't understand why it even mentions IP 192.168. 1.200/ 137... I reset the unit configuring it from scratch and still no go. I have no given a static route to the out yet.. I need to get inter-vlan routing working first. [code]
View 13 Replies View Relatedi configured the VLAN810, with DHCP services, while i try to ping the host which is connected to gi 1/0/2 from my gi 1/0/1 , i can't ping the same vlan host , while i try to debug ip icmp its showing ,
C3750XB11#sh running-config
Building configuration...
Current configuration : 12053 bytes
!
version 12.2
no service pad
service timestamps debug datetime msec
[code]....
In my preparation for my coming CCNA certification I am experimenting with different network configurations. In my test network I am currently working with a "Router on a stick" setup. A Cisco 2611 router connecting a Cisco 2950 switch. VLANs configured on the switch and subinterfaces + dot1q encapsulation configured on the router. Switch only supports dot1q.Router's Eth0/1 is connected to the Switch Fa0/24 port which is also set to trunk mode. I am using a normal Cat5e twisted pair cable to connect the 2 devices.
VLANs are working since I can connect a workstation to an access port for example fa0/2 (vlan2) and get Internet access.I can also ping any of the subinterfaces of the router from the workstation.With the current setup I am not able to ping the switch from the router, or the other way around, so in other words I can't remote manage the switch from a telnet or SSH session with this setup. What I am missing?Just to be clear I am pinging the switch directly from the router (Router2611#ping 172.16.100.2), so please ignore all static routes and OSPF. [code]
Everything in my network works as a charm. Every host in my vlans can access and ping the internet with no problems. But, my main router does not ping the internet (Pinging either ip "173.194.71.104" or domain "www.google.com" do not work). I don't know how is that possible since my hosts can ping the internet. Below is my main router confiurations
!
hostname Internet_Router
!
boot-start-marker
[Code].....
Do I need the Universal image to perform stftp on a 3750 or 3750-X?
View 8 Replies View RelatedI'm looking at adding a Cisco 3750-X switch running c3750e-universalk9-mz.122-55.SE1 (IP base license) into a stack of 3750-G switches running c3750-ipbasek9-mz.122-55.SE1.bin Given that the version and feature sets are the same I don't forsee any compatibility issues. Would there be any reason why a universal image wouldn't stack correctly with other switches running the single .bin file?
View 9 Replies View RelatedWe have a stack of switches that is at the max number of members allowed in the stack. Problem is we are running out of port density and need to add more ports. So instead of adding a whole new stack I would rather replace 2 of the 24-port swicthes with 48-port switches.
If the two 24-port swicthes we are removing are stack members and neither of them are the stack master, I should be able to replace the 24-port switches with the 48-port switches without bringing the master offline? If the new 48-port switches are running the same IOS version as the current 24-port swicthes, they should add themselves to the stack?Would I have to tell the new 48-port swicthes what switch numbers they are replacing in order for them to be added to the stack since we are at the max number of members?Also since the 48-port swicthes are replacing 24-port switches will the master give the 48-port switches the configuration for only the 24-ports?
some of our switches have the switchport mode trunk command configured between the 3750 switches but other 3750 switches connected to our 6509 core switch do not have the switchport mode trunk command to permit Vlans from going across the swtiches instead it has an ip address and says no switchport what is the difference between does two. Is trunking used only for Layer 2 and L3 is used to route interface vlans?
View 2 Replies View RelatedI have a network with a Catalyst 3750 as the main switch and then some Catalyst 2960 switches that are plugged in to that. I have a server running windows server 2008 with a couple of virtual machines running in Hyper-V. I created 4 VLANS listed below and gave the 3750 the following IP Address.I would like the 3750 to only be configurable from VLAN 40 but currently every VLAN can connect to it, I noticed in the standard web page settings there was a setting for "Management VLAN" but it was set to 1 and would not let me change it, I kinda assumed that was for the management port in the back.-Now the tricky part, I was trying to set up routing between the VLANs and so far I have only been able to get a sort of "all or nothing" routing to work. I can turn IP routing on and add two or more VLANs to the routing and it works fine. But what I was hoping to do is create a couple of "junction vlans" that would only route to one or two other vlans. For instance, I wanted to create a VLAN 100 that routed to VLAN 20 and 30 but nothing else. I also want to route VLAN 1 just to VLAN 30, and so on. I am able to do each one of the cases but only one, it seems like the switch only supports one "routing table" am I missing something or is this just a limitation of the switch?
View 2 Replies View RelatedIs a 3750 sw capable of handling full routing tables and what can you recommend in a small mutihomed BGP router or switch capable of handling full routing tables?
View 2 Replies View RelatedI have a network with several catalyst 2960 switches and one catalyst 3750. I have created two VLAN and set up the proper routing and everything is working fine there. I have a client/server application that used multicast in the initial start up for the client to determine available servers, the issue is one of my clients is on a different VLAN then the server. I am able to route the multicast using MVR as long as both the server and the client are plugged into the 3750 by creating a static route, making the server a source port and the client a receive port. Unfortunately I need the client and the server plugged in to different 2960s. My question is how do I establish multicast routing between the two and perferably do it dynamically (always route multicast traffic from one VLAN to another).
View 2 Replies View RelatedI have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net.
My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20
I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2)my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to go out to the internet. I think it has to do with the routes. [code]
I have the task of replicating the router config on a 3825 router on a 3750 switch. Reason is we are taking out the router and replacing it with the switch to make use of the router for other functions.
Below is main part of the router config:
!
ip source-route
ip cef
!
!
multilink bundle-name authenticated
!
license udi pid CISCO3825 sn FCZxxxxxxx
!
vlan internal allocation policy ascending
[code].....
The 3750 switch I have runs C3750E-UNIVERSALK9-M, Version 12.2(55)SE3 on a LAN BASE license.
The first thing I have done is to order for a license upgrade to IP BASE which would give the support for OSPF routing.I do not see much of an issue with the Interface configs, however, I am not too sure about replicating the routing config on the switch.
My question is can I run the commands as shown for the OSPF routing on the switch? If not, can I get suggestions on how best to set this up on the switch?
In 3750 switch,I have configured intervlan routing.I have three vlans Vlan 10,vlan 20,Vlan 30 and I have assigned IP address for that Vlan.In vlan 10,I have connected one systen gigabitethernet 0/1 interface.From my system I am able to ping vlan 10 ip address but I can't able to ping other vlan ip address (vlan 20,vlan 30).Is it possible to up the protocol for all that time.
View 2 Replies View RelatedFor intervlan routing, Is 'IP routing' command enabled by default on a 6500 series switches based on the IOS?and on 3750 switches, do we need to enable the "ip routing" command manually for intervlan routing?
View 1 Replies View RelatedI am using a 3750 as a default gateway for multiple Vlans on a few 2960 switches. The trunk lines are configured and working and I have assigned ip addresses to each of the Vlan interfaces on the 3750. My issue is that I can only ping the ip address on the Vlan interface of the 3750 if I have a working computer plugged directly into the Vlan on the 3750. I only have 3 vlans on the 3750 that have hosts directly connected (vlans 2, 10 and 40) the other vlans ( 20 and 70) don't have any clients plugged into them on the 3750 but the hosts reside on 2 different 2960s that connect via trunk ports. How do I keep the vlan interface on the 3750 switch pingable when I don't have hosts directly connected in that vlan on the 3750? (yes, I have enabled ip routing on the 3750)
View 5 Replies View RelatedI have a simple design with 3750. I configured a route-map which define a next hop. I defined this route-map on a policy on a vlan interface.When I test some ping and a debug ip policy and it seems that my policy never match.Is there any mechanism that prevent the switch from using PBR? I think of CEF .
View 5 Replies View RelatedIn our datacenter we have a 3750 stack with IP base image. I have enabled PBR and reloaded the switch. Show sdm prefer says i am using default template. The reason i want to use PBR is that we have 2 firewalls on the same work and want to be able to have granular control over which gateway out of the network they use but still be able to access all internal resouces accross wan and locally.
Created access list to identify traffic:
access-list 10 permit 10.2.3.59 (test workstation on vlan 3)
Created policy:
route-map TestASA permit 10
match ip address 10
set ip next-hop 10.2.0.3
Assigned policy to the user vlan3:
ip policy route-map TestASA
Results:It changed the default gateway to the above gateway but i could not access any resources on any other vlan, could not access resouces accross wan.
I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net. My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20,I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2),my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to,go out to the internet.
View 3 Replies View RelatedI have a simple design with 3750.I configured a route-map which define a next hop.I defined this route-map on a policy on a vlan interface.When I test some ping and a debug ip policy and it seems that my policy never match.Is there any mechanism that prevent the switch from using PBR?
View 10 Replies View RelatedI'm running into what seems a basic ip routing config problem with a Catalyst 3750 (IP Base) switch. I have several VLANS configured on the switch with IP routing enabled, and the switch is connected to the inside interace of a new ASA 5520 as follows:
ASA5520 IP (Default gateway): 192.168.1.1Switchport Gi1/0/1 is configured as a routed port, IP address 192.168.1.3 255.255.255.0Example VLAN is VLAN 100, IP address 192.168.100.1 255.255.252.0 From the switch CLI, I can ping all VLAN addresses, as well as the ASA5520, and the client laptop I'm testing with from VLAN 100.
From the client laptop on VLAN 100, I can ping all switch interface and VLAN addresses (inter-VLAN routing is working), including 192.168.1.3, but I CANNOT ping the default gateway at 192.168.1.1.
Here is the relevant configuration information on the 3750:
!
no aaa new-model
switch 1 provision ws-c3750x-24
system mtu routing 1500
[Code]....
I have a Cisco 3750 with private VLANS configured.. VLAN 2 is the "primary", VLAN 3 is "isolated" and VLAN 4 is "community". This is all working correctly, however I now have the need to another VLAN called "production". I need the production VLAN to be able to reach all the private VLAN hosts (community and Isolated), and vice versa
View 2 Replies View RelatedFor intervlan routing, Is 'IP routing' command enabled by default on a 6500 series switches based on the IOS?hes, do we need to enable the "ip routing" command manually for intervlan routing?
View 2 Replies View RelatedI have 2 ISP connected to Router A and Router B.Both the routers are connected to the core 3750 switch.. I want to send the traffic from the switch that goes to router A to router B..[code]
View 10 Replies View RelatedI have just bought two Cisco 3750 and stacked them. When in global config mode, The IP Routing Command does not exisit.
See Version below
Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 05-May-11 15:40 by prod_rel_team
Image text-base: 0x00003000, data-base: 0x02800000
I am using a cisco 3750 in my network as a gateway, and above it I use a squid machine for caching my internet. My network is like this:
Basically I have two VLANs on my network which are VLAN10 and VLAN100, VLAN10 is the cooperate network of my office. VLAN100 is the management VLAN which i use for the switches. I keep the squid as well the client in VLAN10.
squid (192.168.1.50)---->cisco 3750(192.168.1.123)---->Distribution Switch(cisco 2960)---->client PC (192.168.1.5)
I have done nating on squid and internet is working pretty fine when I use the client gateway as the squid, but when I use the cisco 3750 as my gateway after adding route maps for forwarding the internet traffic coming to the cisco 3750 to squid it disconnects me from internet as well I cannot even reach the switches from the corporate network. These are the only Lines I used for the routing:
!
route-map proxy-redirect permit 10
match ip address 110
[Code]......
I have a quick query which i need ratified before proceeding. I have the following scenario -
Two Cisco 3750v2 switches with stackwiseISP allocated block of /26 (64 addresses)8 customers each with a VLAN and SVIInternet facing VLAN and SVIDefault route to ISP router Lets say the ISP has given me the network range 10.10.10.0/26 (we'll assume this is routable on the internet for the purposes of this example) and a default gateway to the internet of 10.10.10.1 within this range. I have configured a public facing VLAN as follows -
VLAN 300
name PUBLIC
int VLAN 300
IP Address 10.10.10.2 255.255.255.252
I have then created a default route as follows -
ip route 0.0.0.0 0.0.0.0 10.10.10.1
With this configured, the switch can successfully route upstream to the internet with no problems. I have then moved onto the customers and depending on what service they have purchased, I have subnetted the 10.10.10.0/26 range into smaller subnets. See as follows -
Customer A - 10.10.10.4/30
Gateway IP - 10.10.10.5
Useable IPs - 10.10.10.6
Customer B - 10.10.10.8/29
Gateway IP - 10.10.10.9
Useable IPs - 10.10.10.10 - 10.10.10.14
This continues for each customer depending on how many IP's the have purchased. I have then assigned these IP ranges to a customer VLAN and SVI as follows -
Customer A
VLAN 10
name CUST-A-VLAN
int VLAN 10
ip address 10.10.10.5 255.255.255.252
[code].....
It is then up to the customer as to what equipment they use and how they NAT or firewall their internal networks.
I have a typical LAN environment that spans across a large warehouse. I have done a lot of redesigning of the environment to satisfy the need for a disaster recover plan. I now have created a LAN with multiple v lans and must also connect all the access layer switches back to the core switch where the servers are.
I was thinking of something simple such as Port channel of 2 Gbps across the backbone and simple floating static routes . I have then moved my wan access link to a 3750 and implemented routing a CEF at each of the 3 core switches (blue). My question is more of design.
Which is the best routing method for PBR? is it fast switching? If it is, how can I enable It in my 3750?
View 1 Replies View Related
