Cisco Switching/Routing :: PBR And Fast-switching On 3750
Dec 10, 2012Which is the best routing method for PBR? is it fast switching? If it is, how can I enable It in my 3750?
View 1 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Traffic Within 3750 Slow / But Fast Outside Of It
Jul 15, 2012I have 2 new 3750g devices in a small environment. switch1 acts as our collapsed core and has ip routing enabled, and is connected to a ASA 5510. There are 3 HP l2 switches connected to switch1 as well. switch2 is simply a server switch. switch1 and switch2 have a 2port etherchannel between them, and a vlan trunk carrying 4 vlan's. traffic between any 2 hosts on switch2 (same vlan) are slow. (average 300Mbits/sec) If I move one of those hosts to switch1, speeds increase by 3 times. (average 900 Mbits/sec). Additionally, traffic between any 2 hosts on switch1 are quick. testing is done with iperf as well as timing 1gig file transfers.
I don't see any errors or drops anywhere, and there are no other symptoms other than slow transfer beteween hosts on switch2. I just got 2 more of these 3750's to put in a 2nd site that we have, put a quick configuration on them, and have the same result. Other than switch1 having ip routing enabled, the configs are pretty much identical.
Cisco Switching/Routing :: (lacp Rate Fast) In Catalyst 3750?
Dec 24, 2012I am running the latest version of 12.2(55)SE6 on the catalyst and I am looking for this command "lacp rate fast" but it is not there:
lab-c3750#conf t
Enter configuration commands, one per line. End with CNTL/Z.
lab-c3750(config)#interface g1/0/5
lab-c3750(config-if)#lacp ?
port-priority LACP priority on this interface
lab-c3750(config-if)#lacp
According to this link, it is supposed to work: [URL]Am I missing something?
Cisco Switching/Routing :: Getting Second Fast Ethernet On 2620xm?
Aug 11, 2008I am having a heck of a time finding information on this. I have a 2620xm router that only has one Ethernet port on it. Is there an expansion I can get that allows me another Ethernet port. I have thus far assumed that all of the WIC cards won't allow me to attach to an Ethernet LAN.
View 7 Replies View RelatedCisco Switching/Routing :: LACP Fast Updates On 3750s?
Sep 5, 2012I've got LACP-enabled port-channels between a Cisco 3750 stack and a few different switches (some Cisco 3750s and some Juniper EX2200s). The Ciscos are all sending slow LACP updates, the Junipers are sending fast LACP updates (but the Cisco they connect with is responding with slow LACP updates).
I have a couple of questions:
1) what are the pros and cons of slow vs fast updates? my research has led me to the conclusion that fast updates are better for network resiliency as long as you have plenty of bandwidth overhead (which I do at the moment). is there anything to add to this conclusion?
2) is there any way to configure the Cisco 3750s for fast updates?
Cisco Switching/Routing :: ADSL On Fast Ethernet In 1801?
Apr 24, 2012I have cisco 1801W . Earlier I am using ADSL dynamic IP address on RJ 11 through the ADSL Port but now the ISP change the connection to RJ45.
I am trying to configure it but unable to do this. ADSL line is okay because When I am connecting through the ISP router it is working fine. I have connected the ADSL RJ45 cable in the router fast ethernet 0.But I wanted to use Cisco 1801 Router so that I can use the ADSL as primary and ISDN as the backup.
Below is my configuration, eiteher this is possible to configure ADSL through RJ45 in 1801 and what configuration require for this.
Router#show ip int brief
Interface IP-Address OK? Method Status Protocol
FastEthernet0 unassigned YES DHCP up up
BRI0 unassigned YES unset administratively down down
BRI0:1 unassigned YES unset administratively down down
BRI0:2 unassigned YES unset administratively down down
[code].....
Cisco Switching/Routing :: Errors On WS-C2950T-24 Switch Fast-Ethernet Port?
May 19, 2013SW1#show interfaces fastEthernet 0/14 counters errors
Port Align-Err FCS-Err Xmit-Err Rcv-Err UnderSize
Fa0/14 6682 140364 0 306468 0
Port Single-Col Multi-Col Late-Col Excess-Col Carri-Sen Runts Giants
Fa0/14 0 0 0 0 180103 0 2798
[code]....
Cisco Switching/Routing :: 3850 System LED Blinking Fast - Not Getting Past POST?
May 14, 2013I pulled a brand new Cisco 3850 Switch out of the box yesterday. Following the Quick Start Guide, I put in the power module, powered it on, and waited for it to complete POST. Then, I plugged in an Ethernet cable between a laptop and the switch on a port in the front, and went to the web interface at https://10.0.0.1. I got to the Express Setup, and attempted to change the IP address of the switch to an IP on my LAN, along with other options. When clicking submit, it didn't appear to take. Upon refreshing in the Express Setup, the IP config was blank, so I once again configured it. This time clicking submit brought up a message that it was changing the IP address. I waited for it to finish, and when it looked done, I powered the switch off and took it to a different room to hook it up to the LAN for further configuration.
When plugging in the power at that point, the switch starts through the normal light process (System LED blinks green slowly), and then eventually the System LED blinks green very fast and never stops. It doesn't get to the point of having the system loaded and ready to log into. There's no amber lights, just the System LED flashing green fast. On the back, the Power module and all bay lights are green, and the Console light is green, but the Management port light is off.
I've tried using the reset button on the back of the switch two different times to reset it to default configuration, thinking I hosed it somehow, but it never goes past the fast blinking System LED.
Cisco Switching/Routing :: 3750 - L2 Trunking Versus L3 Switching
Dec 9, 2011some of our switches have the switchport mode trunk command configured between the 3750 switches but other 3750 switches connected to our 6509 core switch do not have the switchport mode trunk command to permit Vlans from going across the swtiches instead it has an ip address and says no switchport what is the difference between does two. Is trunking used only for Layer 2 and L3 is used to route interface vlans?
View 2 Replies View RelatedCisco Switching/Routing :: 2960 / Make Ether Channel On Switch 1 Which Has 24 Fast Ethernet Ports
Oct 8, 2012I have 4 cisco 2960 switches to which many users are connected. No vlans are the only default vlan 1 is there. Now I want to make ether channel on switch 1 whcih has 24 fast etherenet ports. Can I make port 1- 8 as one ether channel which are connected to users or i can only make ethere channel of ports that are connectd to other switchs. If I can, how the other switchs will comnicate with the switch ports bundalled in the ether channel in switch 1.
View 6 Replies View RelatedCisco Switching/Routing :: 3750 - LAN Switching Design
Nov 17, 2011I have a typical LAN environment that spans across a large warehouse. I have done a lot of redesigning of the environment to satisfy the need for a disaster recover plan. I now have created a LAN with multiple v lans and must also connect all the access layer switches back to the core switch where the servers are.
I was thinking of something simple such as Port channel of 2 Gbps across the backbone and simple floating static routes . I have then moved my wan access link to a 3750 and implemented routing a CEF at each of the 3 core switches (blue). My question is more of design.
Cisco Switching/Routing :: Perform STFTP On 3750 Or 3750-X?
Jun 30, 2012Do I need the Universal image to perform stftp on a 3750 or 3750-X?
View 8 Replies View RelatedCisco Switching/Routing :: Stacking 3750-X With Universal Image With 3750-G Running BIN Image?
Oct 10, 2011I'm looking at adding a Cisco 3750-X switch running c3750e-universalk9-mz.122-55.SE1 (IP base license) into a stack of 3750-G switches running c3750-ipbasek9-mz.122-55.SE1.bin Given that the version and feature sets are the same I don't forsee any compatibility issues. Would there be any reason why a universal image wouldn't stack correctly with other switches running the single .bin file?
View 9 Replies View RelatedCisco Switching/Routing :: Replacing 3750 24 Port With 3750 48 Port?
May 21, 2012We have a stack of switches that is at the max number of members allowed in the stack. Problem is we are running out of port density and need to add more ports. So instead of adding a whole new stack I would rather replace 2 of the 24-port swicthes with 48-port switches.
If the two 24-port swicthes we are removing are stack members and neither of them are the stack master, I should be able to replace the 24-port switches with the 48-port switches without bringing the master offline? If the new 48-port switches are running the same IOS version as the current 24-port swicthes, they should add themselves to the stack?Would I have to tell the new 48-port swicthes what switch numbers they are replacing in order for them to be added to the stack since we are at the max number of members?Also since the 48-port swicthes are replacing 24-port switches will the master give the 48-port switches the configuration for only the 24-ports?
Cisco Switching/Routing :: Multiple VLAN Routing Tables For 3750 Catalyst
Oct 24, 2012I have a network with a Catalyst 3750 as the main switch and then some Catalyst 2960 switches that are plugged in to that. I have a server running windows server 2008 with a couple of virtual machines running in Hyper-V. I created 4 VLANS listed below and gave the 3750 the following IP Address.I would like the 3750 to only be configurable from VLAN 40 but currently every VLAN can connect to it, I noticed in the standard web page settings there was a setting for "Management VLAN" but it was set to 1 and would not let me change it, I kinda assumed that was for the management port in the back.-Now the tricky part, I was trying to set up routing between the VLANs and so far I have only been able to get a sort of "all or nothing" routing to work. I can turn IP routing on and add two or more VLANs to the routing and it works fine. But what I was hoping to do is create a couple of "junction vlans" that would only route to one or two other vlans. For instance, I wanted to create a VLAN 100 that routed to VLAN 20 and 30 but nothing else. I also want to route VLAN 1 just to VLAN 30, and so on. I am able to do each one of the cases but only one, it seems like the switch only supports one "routing table" am I missing something or is this just a limitation of the switch?
View 2 Replies View RelatedCisco Switching/Routing :: Is 3750 SW Capable Of Handling Full Routing Tables
Oct 8, 2012Is a 3750 sw capable of handling full routing tables and what can you recommend in a small mutihomed BGP router or switch capable of handling full routing tables?
View 2 Replies View RelatedCisco Switching/Routing :: Catalyst 3750 Multi-cast VLAN Routing
Oct 28, 2012I have a network with several catalyst 2960 switches and one catalyst 3750. I have created two VLAN and set up the proper routing and everything is working fine there. I have a client/server application that used multicast in the initial start up for the client to determine available servers, the issue is one of my clients is on a different VLAN then the server. I am able to route the multicast using MVR as long as both the server and the client are plugged into the 3750 by creating a static route, making the server a source port and the client a receive port. Unfortunately I need the client and the server plugged in to different 2960s. My question is how do I establish multicast routing between the two and perferably do it dynamically (always route multicast traffic from one VLAN to another).
View 2 Replies View RelatedCisco Switching/Routing :: Inter-VLan Routing On Catalyst 3750 Switch
Dec 17, 2011I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net.
My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20
I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2)my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to go out to the internet. I think it has to do with the routes. [code]
Cisco Switching/Routing :: 3825 / Replacing Routing Function With 3750 Switch?
Jul 27, 2012I have the task of replicating the router config on a 3825 router on a 3750 switch. Reason is we are taking out the router and replacing it with the switch to make use of the router for other functions.
Below is main part of the router config:
!
ip source-route
ip cef
!
!
multilink bundle-name authenticated
!
license udi pid CISCO3825 sn FCZxxxxxxx
!
vlan internal allocation policy ascending
[code].....
The 3750 switch I have runs C3750E-UNIVERSALK9-M, Version 12.2(55)SE3 on a LAN BASE license.
The first thing I have done is to order for a license upgrade to IP BASE which would give the support for OSPF routing.I do not see much of an issue with the Interface configs, however, I am not too sure about replicating the routing config on the switch.
My question is can I run the commands as shown for the OSPF routing on the switch? If not, can I get suggestions on how best to set this up on the switch?
Cisco Switching/Routing :: 3750 Inter Vlan Routing Configuration
Mar 24, 2013In 3750 switch,I have configured intervlan routing.I have three vlans Vlan 10,vlan 20,Vlan 30 and I have assigned IP address for that Vlan.In vlan 10,I have connected one systen gigabitethernet 0/1 interface.From my system I am able to ping vlan 10 ip address but I can't able to ping other vlan ip address (vlan 20,vlan 30).Is it possible to up the protocol for all that time.
View 2 Replies View RelatedCisco Switching/Routing :: IP Routing On 6500 Series Versus 3750?
Jan 24, 2013For intervlan routing, Is 'IP routing' command enabled by default on a 6500 series switches based on the IOS?and on 3750 switches, do we need to enable the "ip routing" command manually for intervlan routing?
View 1 Replies View RelatedCisco Switching/Routing :: InterVlan Routing With 3750 And 2960 Switches?
Nov 21, 2012I am using a 3750 as a default gateway for multiple Vlans on a few 2960 switches. The trunk lines are configured and working and I have assigned ip addresses to each of the Vlan interfaces on the 3750. My issue is that I can only ping the ip address on the Vlan interface of the 3750 if I have a working computer plugged directly into the Vlan on the 3750. I only have 3 vlans on the 3750 that have hosts directly connected (vlans 2, 10 and 40) the other vlans ( 20 and 70) don't have any clients plugged into them on the 3750 but the hosts reside on 2 different 2960s that connect via trunk ports. How do I keep the vlan interface on the 3750 switch pingable when I don't have hosts directly connected in that vlan on the 3750? (yes, I have enabled ip routing on the 3750)
View 5 Replies View RelatedCisco Switching/Routing :: Policy Based Routing With 3750 Switches
Oct 17, 2011I have a simple design with 3750. I configured a route-map which define a next hop. I defined this route-map on a policy on a vlan interface.When I test some ping and a debug ip policy and it seems that my policy never match.Is there any mechanism that prevent the switch from using PBR? I think of CEF .
View 5 Replies View RelatedCisco Switching/Routing :: How To Configure Policy Based Routing On 3750
Jan 28, 2013In our datacenter we have a 3750 stack with IP base image. I have enabled PBR and reloaded the switch. Show sdm prefer says i am using default template. The reason i want to use PBR is that we have 2 firewalls on the same work and want to be able to have granular control over which gateway out of the network they use but still be able to access all internal resouces accross wan and locally.
Created access list to identify traffic:
access-list 10 permit 10.2.3.59 (test workstation on vlan 3)
Created policy:
route-map TestASA permit 10
match ip address 10
set ip next-hop 10.2.0.3
Assigned policy to the user vlan3:
ip policy route-map TestASA
Results:It changed the default gateway to the above gateway but i could not access any resources on any other vlan, could not access resouces accross wan.
Cisco Switching/Routing :: About Intervlan Routing On Catalyst 3750 Switch
Apr 16, 2012I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net. My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20,I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2),my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to,go out to the internet.
View 3 Replies View RelatedCisco Switching/Routing :: Policy Based Routing And 3750 Switches?
Sep 5, 2012I have a simple design with 3750.I configured a route-map which define a next hop.I defined this route-map on a policy on a vlan interface.When I test some ping and a debug ip policy and it seems that my policy never match.Is there any mechanism that prevent the switch from using PBR?
View 10 Replies View RelatedCisco Switching/Routing :: Cannot Reach Gateway Through Routing Switch (3750)
Mar 11, 2012I'm running into what seems a basic ip routing config problem with a Catalyst 3750 (IP Base) switch. I have several VLANS configured on the switch with IP routing enabled, and the switch is connected to the inside interace of a new ASA 5520 as follows:
ASA5520 IP (Default gateway): 192.168.1.1Switchport Gi1/0/1 is configured as a routed port, IP address 192.168.1.3 255.255.255.0Example VLAN is VLAN 100, IP address 192.168.100.1 255.255.252.0 From the switch CLI, I can ping all VLAN addresses, as well as the ASA5520, and the client laptop I'm testing with from VLAN 100.
From the client laptop on VLAN 100, I can ping all switch interface and VLAN addresses (inter-VLAN routing is working), including 192.168.1.3, but I CANNOT ping the default gateway at 192.168.1.1.
Here is the relevant configuration information on the 3750:
!
no aaa new-model
switch 1 provision ws-c3750x-24
system mtu routing 1500
[Code]....
Cisco Switching/Routing :: 3750 Private VLAN With Routing
Jan 1, 2012I have a Cisco 3750 with private VLANS configured.. VLAN 2 is the "primary", VLAN 3 is "isolated" and VLAN 4 is "community". This is all working correctly, however I now have the need to another VLAN called "production". I need the production VLAN to be able to reach all the private VLAN hosts (community and Isolated), and vice versa
View 2 Replies View RelatedCisco Switching/Routing :: IP Routing On 6500 Series Vs 3750?
Oct 30, 2011For intervlan routing, Is 'IP routing' command enabled by default on a 6500 series switches based on the IOS?hes, do we need to enable the "ip routing" command manually for intervlan routing?
View 2 Replies View RelatedCisco Switching/Routing :: Policy Based Routing 3750
Dec 2, 2012I have 2 ISP connected to Router A and Router B.Both the routers are connected to the core 3750 switch.. I want to send the traffic from the switch that goes to router A to router B..[code]
View 10 Replies View RelatedCisco Switching/Routing :: 3750 / IP Routing Command Not Existent
Feb 27, 2013I have just bought two Cisco 3750 and stacked them. When in global config mode, The IP Routing Command does not exisit.
See Version below
Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 05-May-11 15:40 by prod_rel_team
Image text-base: 0x00003000, data-base: 0x02800000
Cisco Switching/Routing :: 3750 To Squid Routing Not Working
Nov 23, 2011I am using a cisco 3750 in my network as a gateway, and above it I use a squid machine for caching my internet. My network is like this:
Basically I have two VLANs on my network which are VLAN10 and VLAN100, VLAN10 is the cooperate network of my office. VLAN100 is the management VLAN which i use for the switches. I keep the squid as well the client in VLAN10.
squid (192.168.1.50)---->cisco 3750(192.168.1.123)---->Distribution Switch(cisco 2960)---->client PC (192.168.1.5)
I have done nating on squid and internet is working pretty fine when I use the client gateway as the squid, but when I use the cisco 3750 as my gateway after adding route maps for forwarding the internet traffic coming to the cisco 3750 to squid it disconnects me from internet as well I cannot even reach the switches from the corporate network. These are the only Lines I used for the routing:
!
route-map proxy-redirect permit 10
match ip address 110
[Code]......
Cisco Switching/Routing :: 3750 - Public VLAN Routing?
Dec 8, 2011I have a quick query which i need ratified before proceeding. I have the following scenario -
Two Cisco 3750v2 switches with stackwiseISP allocated block of /26 (64 addresses)8 customers each with a VLAN and SVIInternet facing VLAN and SVIDefault route to ISP router Lets say the ISP has given me the network range 10.10.10.0/26 (we'll assume this is routable on the internet for the purposes of this example) and a default gateway to the internet of 10.10.10.1 within this range. I have configured a public facing VLAN as follows -
VLAN 300
name PUBLIC
int VLAN 300
IP Address 10.10.10.2 255.255.255.252
I have then created a default route as follows -
ip route 0.0.0.0 0.0.0.0 10.10.10.1
With this configured, the switch can successfully route upstream to the internet with no problems. I have then moved onto the customers and depending on what service they have purchased, I have subnetted the 10.10.10.0/26 range into smaller subnets. See as follows -
Customer A - 10.10.10.4/30
Gateway IP - 10.10.10.5
Useable IPs - 10.10.10.6
Customer B - 10.10.10.8/29
Gateway IP - 10.10.10.9
Useable IPs - 10.10.10.10 - 10.10.10.14
This continues for each customer depending on how many IP's the have purchased. I have then assigned these IP ranges to a customer VLAN and SVI as follows -
Customer A
VLAN 10
name CUST-A-VLAN
int VLAN 10
ip address 10.10.10.5 255.255.255.252
[code].....
It is then up to the customer as to what equipment they use and how they NAT or firewall their internal networks.