Cisco WAN :: 887VA VDSL Controller Firmware Upgrade?
Sep 19, 2011
I'm trying to upgrade the VDSL firmware on a 887VA. I've uploaded the file vdsl.bin-A2pv6C035d_d23j to the router. I understand this file has to be renamed with a .bin extension in order to be recognized after a reboot, but the attempts I have made have not worked. What must this file be renamed to in order to load the new firmware into the VDSL controller?
Here is the current firmware information. I've tried several of the obvious file names.
Firmware Source File Name (version)-------- ------ -------------------VDSL embedded VDSL_LINUX_DEV_01212008 (1)
Modem FW Version: 110331_1212-4.02L.03.A2pv6C032b.d23fModem PHY Version: A2pv6C032b.d23f
View 1 Replies
ADVERTISEMENT
Apr 28, 2013
what enhancements, fixes, etc are included in the Cisco 887VA VDSL firmware version A2pv6C035l.d23j, relased 29-MAR-2013.I can't seem to find any release notes with this firmware.We are using version A2pv6C035d.d23j firmware on around 150 887VA's on BT ADSL lines, and was looking for any improvements this version may offer.
View 1 Replies
View Related
Nov 25, 2011
I'm trying to get an internet connection through my cisco 877va but I can't get access. I can see DSL up, however, the dialer0 interface can't get access to internet. Here is my configuration:
[code].....
View 2 Replies
View Related
Jun 17, 2012
I'm facing an issue since 2 month now , no one is able to tell me what's going on. The line goes down suddently for 2 or 3 minutes and this happens everyday at the same range (~2 or 3 hours) of time . I don't have any scheduled task to cause this. ISP in his side has also made some tshoot but found nothing and is convinced that the problem is coming from our side :
Here is some log :
Cisco IOS Software, C880 Software (C880DATA-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
rtr-Id#show debugging
Generic IP:
IP packet errors debugging is on
IP NAT ERROR debugging is on
PPP:
[Code]...
View 3 Replies
View Related
Aug 24, 2012
Just got hold of my first 887va for my home, never configured a vdsl interface before and was just wondering if my setup looked good to someone whos done it a few times.
View 6 Replies
View Related
Mar 13, 2013
Trying to get my 887va setup for VDSL but can't get to anything on the net -
Controller VDSL 0vpdn enablevpdn-group 1
interface ethernet0
no ip address
[Code].....
View 6 Replies
View Related
Mar 1, 2012
I am in the midst of trying to update the controller firmware of a cisco wireless lan contoller 4402, and having some issues getting the file to transfer to the controller. i am currently running verison 5.0.148 on the controller and attempting to upgrade to the latest version of 7.0.230 and for whatever reason it continues to not transfer. I have tried all 3 methods of cli, gui and using wcs software. all the no avail , I have tried tftp32 and 3cdaemon with the same results.
The error that i am getting from 3cdaemon is got socket timeout aborting code 10054, failing at 66MB transfered. I increased the timeouts both on the wlc and the tftp client to no avail
the error i get on the wlc is Code file transfer failed - Error while writing output file
View 5 Replies
View Related
Feb 22, 2013
Region : Others
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 1.8
ISP :
Region : Israel
Model : TL-WR1043ND
Hardware Version (On the back cover): V1.8
From web interface:
Firmware Version:3.13.4 Build 110429 Rel.36959n
Hardware Version:WR1043ND v1 00000000
ISP : Free
1. about USB Printer Controller
I connect my printer HP office jet 5610 All in one, his drivers installed on my computer (windows 7 ultimate, 32 bit). Irun the software "USB Printer Controller" and i didn't seeing anything. Can not click on any button. BTW, i changed the IP range from 192.168.1.1 to 10.0.0.100-10.0.0.139 and my router web interface at 10.0.0.140, if it's changing something.
2. About upgrade the router's firmware, it's safe that I'll upgrading it?
The last version : TL-WR1043ND_V1_120405
View 1 Replies
View Related
Apr 13, 2013
Region : Denmark
Model : TL-WDR4300
Hardware Versin : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP :
my TP-Link USB Controller after my latest firmware upgrade, and therefor my USB-printer (connected to the router) do not function any more, and i can not find a new software for the Controller
View 1 Replies
View Related
Jun 19, 2012
I am facing a problem to install a ap upgrade lic file on controller 5500. Iam getting the following error:
% Error: License file transfer failed - Error from server: File not found
I have confusion here that when I configure this command from GUI
tftp://172.32.45.22/cmm/standard.lic
What i should use for /cmm/ ????
Let say i have lic. file is on desktop of tftp server computer and I say in this command
tftp://10.12.70.35/??/license file .lic
View 6 Replies
View Related
Aug 30, 2012
difference of CISCO887VA-K9 and CISCO887VA-SEC-K9.I thought it because of the Advanced Security and Advanced IP Licenses, but it isn't, I've got the -SEC- Version now just with the Advanced Security license. So I asking myself why I bought the more expensive CISCO887VA-SEC-K9 if I have to buy the additional Advanced IP Services licenses extra..
View 14 Replies
View Related
Feb 11, 2012
I will upgrade my Wireless Controller Firmware 7.2.103.0 But I dont know WCS will support manager new controller firmware 7.2.103.0 ?is need NCS to manager? or WCS can be manager new controller firmware 7.2.103.0 all feature?
Now My hw is
Csico 6509 Sup 720 3b 12(33)SXJ
My Controller is WiSM2
WiSM2 is 7.0.116.0
WCS is 7.0.172.0
View 6 Replies
View Related
May 11, 2013
I have a wireless controller that works perfect but because we have some new access-points 1602i that is only supported bij software version 7.4.100.0. So I need to upgrade the controller because I now have version 7.0.116.0. I have read in release notes of version 7.4.100.0 that I first need to upgrade to 7.0.240.0 to avoid losing those VLAN settings.
Note If you have VLAN support and VLAN mappings defined on H-REAP access points and are currently using a 7.0.x controller software release that is prior to 7.0.240.0, we recommend that you upgrade to the 7.0.240.0 release and then upgrade to 7.4.100.0 to avoid losing those VLAN settings.
But I also read something about Field Upgrade Software. If you are using a Cisco 2500 Series controller and you intend to use the Application Visibility and Control (AVC) and Net Flow protocol features, you must install Wireless LAN Controller Field Upgrade Software for Release 1.8.0.0-FUS. This is not required if you are using other controller hardware models. For more information, see [URL] .....
Here is the system information of my controller:
Manufacturer's Name.............................. Cisco Systems Inc.Product Name..................................... Cisco Controller Product Version.................................. 7.0.116.0Bootloader Version............................... 1.0.16Field Recovery Image Version..................... 1.0.0Firmware Version................................. PIC 16.0
Build Type....................................... DATA + WPS
System Name...................................... WIFI-WLC-01System Location.................................. System
[Code] ....
I was thinking of the following steps:
1. Backup the current config
2. Upgrade to version 7.0.240.0
3. Test and backup the config
4. Upgrade to version 7.4.100.0
5. Test and backup the config
6. Upgrade Field Upgrade Software 1.8.0.0
7. Test
View 3 Replies
View Related
Mar 7, 2013
I can figure out why I cant ping controller 10.1.99.100. Here is my controller config. It is connect to H3C 5800 switch. I have the switch config below as well. The port on the switch is on Native Vlan 1 untagged.
(Cisco Controller) show>interface summary
Interface Name Port Vlan Id IP Address Type Ap Mgr Guest
-------------------------------- ---- -------- --------------- ------- ------ -----
ap-manager 1 untagged 10.1.99.101 Static Yes No
[Code]....
View 30 Replies
View Related
Sep 28, 2010
A customer has wireless LAN controller with version 4.2.205.0 and i want to upgrade it to version 7.do i need to upgrade the controller to intermediate version or i cant directly upgrade it.
View 2 Replies
View Related
Jun 16, 2013
upgrade on the wireless controller 2504 from 7.0 to 7.4 is direct upgrade.My customer faced problem by upgrading the software 7.0 to 7.4 directly and the image hang.how should proceed recover the image 7.4/
View 7 Replies
View Related
Jan 29, 2012
We are looking to upgrade our 5508 wireless controller from 7.0.98.0 to 7.0.220.0. Reason being, we have experienced a lot of access points disassociating from the controller as well as client authentication issues. Upgraded from 7.0.98.0 to 7.0.220.0 and any issues during the upgrade or after the upgrade?
View 3 Replies
View Related
Sep 13, 2011
I have one instance of WCS 7.0.172.0 (on a Linux host) and a fleet of WiSMs that I'm upgrading from 7.0.98.0 to 7.0.116.0. Every time I run thru the upgrade process from within WCS (scheduled to run overnight, off peak hours) all of the controllers that were upgraded then show as "unreachable". Grepping thru wcs-0-0.log shows messages that the controllers are unreachable via SNMP but running an "snmpget" from the command line to any of the affected controllers works just fine. The only way I've found to remedy this is to stop and restart the WCS service. Considering how long that takes with my deployment...I'd rather not do that every time .
View 2 Replies
View Related
Dec 12, 2011
I need to upgrade WCS firmware. Currently i am running with 7.0.172.0 .
View 1 Replies
View Related
Feb 28, 2013
I want to upgrade a 5508 WLC from version 6.0.196.0 to the most recent 7.4or 7.3 is it ok to skip so many versions, will this cause an issue?
View 9 Replies
View Related
Aug 18, 2011
I have an AIR-AP1242AG-E-K9 which had c1240-k9w8-mx.124-21a.JA loaded, I followed the link below and upgraded with Cisco’s upgrade tool to c1240-rcvk9w8-mx with no problems at all, after the upgrade I could then see the LWAP on the 4402 controller and had it working a treat.Now the problems begin, I brought it into the office where we have 5508 controllers, plug in the LWAP into our management switch and boot it up I get an IP assigned from the DHCP server and the AP goes into discovery mode but never finds the controller.I have logged the boot process but this does not give much away, our other 1100 series AP’s boot fine,
[URL]
Console Boot Log.
Xmodem file system is available.
flashfs[0]: 9 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
[code]....
And that is where she sits and does nothing more, I have noticed the DNS problems but the other 1100 series LWAP’s boot up after show that same issue.
View 2 Replies
View Related
Feb 6, 2012
I'm about to upgrade a 5508 controller so I can do the pre-download to the access points, but in every doc I find, it says to disable the WLAN's before upgrading. This makes no sense. I'm just moving code over, why do I have to disrupt my wireless network in order to move code?
View 7 Replies
View Related
Jan 27, 2013
I have a 4402-12-k9 controller and I need to upgrade to 25 APs Can I buy a 12 or 25 license upgrade to this controller?
View 7 Replies
View Related
Dec 16, 2012
Any online 2504 controller crash after upgrade to the point where even console port does not put anything out? Perfectly working 2504 running 7.0.116 ran upgrade through web GUI to 7.2. GUI showed perfect transfer, save etc... Asked for save before reboot. Select yes. Controller reboot and now it sits with following status lights:Power-greenSYS - amber blinkingALM - amber solidNothing out of console.
View 8 Replies
View Related
Apr 5, 2013
I have a 5508 wireless controller running version 6.0.199.4 (the image installed when the device was shipped) and I am trying to install by tftp version 7.3.112.0
The issue is when using tftpd32 gets to 82% transfered then fails with the error "% Error: Code file transfer failed - Error while writing output file"
View 7 Replies
View Related
Dec 29, 2011
I should upgrade ASA 5550 with nat controller enabled, from 7.2 to 8.x, I've been reading nat is differently configured up from release 8.3. So I choosed to upgrade to 8.2 release.
View 3 Replies
View Related
Mar 2, 2012
Recently I brought SG 300-28.It came loaded with firmware ver 1.0.0.27.Can I upgrade it to ver 1.1.2.0 directly?
View 2 Replies
View Related
Sep 17, 2012
I currently have 3 WAP4410n's (actually, they're WAP4410N-E V02s) that have been really unreliable since I got them - so much so that we've had to cron a restart script on another server which is frankly ridiculous - they've always run firmware version 2.0.2.1.
I've tried updating the firmware to new versions in the past with no success - when I do so, it looks like everything's fine, but when I log back in, the fixed IP address information isn't shown, and the wireless is disabled. I can enable it, but I can't select a channel.
At this point, I have to revert back to the old firmware. I've tried restoring to factory setttings before and after the firmware flash, but this hasn't changed anything.
However, recently I was able to flash firmware 2.0.5.3 onto only one of the routers - it worked fine and all information was displayed and wireless enabled correctly. However on the other two, no matter what I try, the firmware won't upgrade succesfully - it looks like everything's fine, but the fixed IP information isn't shown and wireless/channels are disabled.
View 5 Replies
View Related
Feb 5, 2011
I have a Dir-655 A3 with the firmware 1.32NA. I cannot get the new firmware 1.35NA to take. The router seems to go through the motions of the upgrade, but at the end, when I log back on, the firmware still says 1.32NA & all custom settings remain.I have upgraded the firmware on this router before and I know that when its upgraded, the router is basically reset to factory settings. All the settings have been backed up and I am attempting this upgrade via a wired connection.
View 2 Replies
View Related
Mar 28, 2012
I have a DIR-655 Rev A4.I followed this forum in the past when there were many problems with firmware upgrades beyon 1.21. Because of this I never upgraded and was told to be satisfied that I can still stay with 1.21 as upgrades caused problems for a number of people.Everything still seems fine with 1.21 except the Shareport utility often does not pickup the printer connection upon booting to Windows Vista. I can always work around this by Disable and then Enable. It will then always find the printer. It is a minor annoyance however.Should I still stay with 1.21 or is upgrading to 1.35 NA recommended ? If I upgrade to 1.35 NA is there a downgrade path back to 1.21 if the upgrade does not work well ?
View 12 Replies
View Related
Jun 5, 2012
We have Cisco 4402 Wireless Lan Controller with Software Version 3.2.171.6 and we want to upgrade it to latest version.
What is the latest version to upgrade the WLC?
Also since WLC is running on very lower version is it possible to upgrade to the latest version directly or we have to move it step by step to upgrade this to latest version?
View 3 Replies
View Related
Sep 14, 2011
It baffles me because the admin console doesn't look like it will browse your computer for a firmware update. Rather, it prefers you to specify a tftp or http server. I don't know how I'd set up my computer to be the http or tftp server and it doesn't really go into detail on what configurations or commands that would need to be used. I've used a tftp client in the past to send a firmware to routers and whatnot but not serve one.
View 1 Replies
View Related
Dec 27, 2012
I have firmware version 2.0.2.7. I've down loaded the firmware upgrade utility ver 1.3, and do not see a read me or help file. I've disconnected the cables as directed, but recive a 'broadcast error' and a 'browse device error'
View 2 Replies
View Related
