Cisco LAN :: ASA 5505 Vlan1 IP Change?

Dec 27, 2009

In default mode the ASA 5505 is setup with two Vlan's, one inside and one outside. Vlan1 is the default inside VLan, with IP 192.168.1.1. I would like to change the subnet of Vlan1 tot 192.168.10.1, but when I do, no Ethernet port is assigned to Vlan1 anymore (was 0/1 - 0/7). What I have done is;
 
#config t
(config)#interface vlan 1
(config)#ip address 192.168.10.1 255.255.255.0
 
But after that, no Ethernet port is within Vlan1, so I tried the following to assign one (port 0/1);
 
#config t
(config)#interface 0/1
(config)#switchport access vlan 1
(config)#no shut
 
But nothing happends when monitoring (#show run) interface 0/1 (no Vlan assigned)

View 6 Replies


ADVERTISEMENT

Cisco Switches :: SGE2010 - Change VLAN1 IP Address?

May 20, 2013

I want to know how am i do to change the Vlan1`s IP address because the actual ip will be used in another vlan. Actually i haver 10 vlans in L3 mode (routing) implemented in it.

View 5 Replies View Related

Cisco VPN :: Change Gateway Through ASA 5505

May 28, 2011

I have four ASA 5505 devices connected via tunnels.  All of the tunnels have a single point of exit to the outside, an AT&T T1 line.  Because of issues with bandwidth, I added a secondary line to each site.  In this case the secondary line is a comcast high speed internet connection.  What I would like to do is set up a route so that any traffic that is going to the internet (browser or email) be directed through the Comcast line and all internal traffic (file transfer, ERP, VOIP) can be directed to the AT&T line.  Each has a separate ip address.  There is a single default gateway set up on the ASA now. 

View 1 Replies View Related

Cisco WAN :: ASA 5505 Remote WAN IP Change?

Dec 6, 2010

There is a site I oversee that is moving to a new ISP. The drive is 2 hours round trip and I need to do is change an IP. DHCP is being handed out by the internal Domain Controller and all the workstations point to the server for DNS. Will the following commands inputted over an SSH putty session into the current WAN IP change the IP and allow me to hookup to the new ISP? The plan is to copy and paste the following commands into global config mode. Currently they are using DHCP on the WAN side which I do not approve of and their external route is pointing to the internal IP of 192.168.1.1. Things still work but I want to do away with this. Will these commands get the job done?

interface vlan 2ip address 68.x.x.2 255.255.255.240exitno route outside 0.0.0.0 0.0.0.0 192.168.1.1route outside 0.0.0.0 0.0.0.0 68.x.x.1

View 7 Replies View Related

Cisco Firewall :: Using ASDM To Change External IP Address Of 5505?

Mar 13, 2013

We have an ASA 5505 and are changing ISPs so we'll be getting a new static IP address. How do I change the external IP address using ASDM? (I haven't done it in 5 years so I'm rusty and just want ot make sure.) The ASA and ASDM are up to date.Am i correct in that I only need to change the external address in the configuration under Interfaces, then under Routing - Static Routes - Gateway IP I just need to enter the new WAN gateway address?

View 2 Replies View Related

Cisco VPN :: 5505 How To Change EasyVPN Head-end Server Address

Jan 19, 2012

We have a number of 5505 ASAs at remote sites all of which are configured to connect to one of two head-end servers.We need to change the primary head-end IP addresses.  At the moment devices are successfully connected to the secondary.If we issue vpnclient server i.j.k.l e.f.g.h then the device drops off the network and won't reconnect until it is power cycled.If we make the changes in ASDM using the GUI to remove the old primary and add in the new primary the ASDM says "No changes made".Devices are running 8.2 and 8.4 code and behaviour is the same.
 
how to change head-end server IP addresses without the device disconnecting and not coming back up?  According to the configuration guide the ASA should cycle through the addresses every 8 seconds until it can connect - but it doesn't seem to do this as it won't connect to the good secondary head-end either!

View 1 Replies View Related

Cisco Firewall :: 5505 / 5585 - Licensing Change On ASAs

Jan 16, 2013

I just learned that the licensing structure for the ASAs is changing, but I don't have any details. We have roughly 30 ASAs (from 5505s to 5585s).  If there's a licensing change, I need to do an impact assessment and plan accordingly. 

View 5 Replies View Related

Cisco :: WS-C4948 Vlan1 Management From Outside?

Feb 3, 2013

I'm trying to get a catalyst going for remote management using cisco network assistant.I've basically, enabled telnet;

enable conf t line vty 0 15 password {password}
login
exit
gave it an IP;
int vlan1 ip address {IP} {Subnet}
no shutdown
exit

[code]...

and write mem to save it all. I can ping, telnet and access cisco network assistant from inside the network perfectly. But the problem I'm having is accessing it from outside, can't even ping the device. I can ssh to other servers behind the network just fine. There is no firewall in place at the moment, the provider's drop is plugged in gige port 1?

View 3 Replies View Related

Cisco WAN :: 877 / 2960 - HSRP Configuration On VLan1

Nov 13, 2012

I have the following topology:

2x 877 routers, one interface from each router (port Fa0 which belongs to the router internal switch) is connected to the 2960 switch, the switch himself configured with default settings, flat with one v LAN.

I have configured HSRP in the following manner: router A is 10.0.0.2, router B is 10.0.0.3, virtual IP is 10.0.0.1, take note that the HSRP configuration along with the IP address are configured on vlan1 interface.
 
Now when i connect a PC to the switch with static IP (10.0.0.4) and trying to ping 10.0.0.1 I'm not getting replies. i see on the PC, using wire shark, the icmp request goes out but on the primary router (and also on the backup) i can't see the icmp request (using debug ip icmp).
 
this behavior happens only when the HSRP is configured on interface vlan1, when configuring the same configuration on Fa4 (which is WAN interface) everything works fine.

View 4 Replies View Related

Cisco Firewall :: ASA5505 Vlan1 Down Active Workstations

Feb 26, 2012

I have an ASA5505 where vlan1 (inside) and all associated ports (e0/1 - e0/7) are down.  Workstations on vlan 1 are online and working.  Vlan2 (outside) is up and running normally.  I tried to shut/no shut on the vlan.  I also rebooted the firewall.  No change.  Why vlan1 is down??  I've attached some config info and some troubleshooting.

View 5 Replies View Related

Cisco WAN :: 887V VDSL Router / Pinging From The VLAN1?

Apr 7, 2011

I have a problem with my Cisco 887V VDSL-router. The router gets a ip-address with dhcp from my provider. That works fine. I also can ping from the router:
 
routerVdslTestNew#ping google.ch source vlan 1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 74.125.79.99, timeout is 2 seconds:
Packet sent with a source address of 10.10.10.1
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 48/48/52 ms
 
My problem: If I want to ping google from a computer in the VLAN1 the ping doesn't work.
 
C:UsersXXXXXX>ping 74.125.79.99
Ping wird ausgeführt für 74.125.79.99 mit 32 Bytes Daten:
Timeout.

View 3 Replies View Related

Cisco Switching/Routing :: 1721 - Vlan1 Cannot Go To Internet

May 12, 2013

router 1721 with one wic-1adsl ,i have adsl conection with irb static ip. the router connect with mannaged switch through a trunk port. the switch has 2 vlans one for the static IPs and the other for private lan. i need the private lan to be able to go to internet. vlan2 can go to internet because it has the same subnet with provider but vlan 1 canot go internet, so how i can make all vlans go internet(the router has only 1 fastethernet port)

View 4 Replies View Related

Cisco :: Nexus 5548UP 2248TP To 3650G Vlan1 Trunking

Jun 4, 2012

Got an odd problem with trunking, all vlans except vlan1 trunk perfectly. Link is from a pair of dualhomed FEX 2248TP's to some 3650G Switches. Nexus running - version 5.1(3)N2(1) 3560's running - 12.2(53)SE2 & 15.0(1)SE2

View 3 Replies View Related

Cisco Switching/Routing :: WS-2950s Dropping VLAN1 Connectivity

Jan 16, 2012

I have a problem where only the 2950's switches go transperant. They drop VLAN1 thus no CDP snmp packets. The users keep working fine but our NMS center keeps calling me at 3am when this happens.
 
These are access switches that connect to stacked 3750's. Some of the uplinks are using media converters that i have been trying to get removed. But i doubt that it could be the cause of the vlan1 going down.

View 3 Replies View Related

Cisco Routers :: RV042 Setup - VLAN1 To VLAN2 Access?

Nov 19, 2011

I have 2 VLANs set up and I know they are set as default to not allow one to communicate to the other.  Is there a way to set a rule to allow that?  I'd like VLAN1 to be able to access VLAN2, but not the other way around.

View 1 Replies View Related

Cisco Switching/Routing :: 3560 - Native Vlan1 Over Trunk

Jan 28, 2013

if i have this config:
switch port mode trunk
trunk aloved vlan 50
 
will travel over this trunk untagged packets? For eg the V LAN 1 is by default native V LAN without tag. If i have created a bog ring with catalyst 3560x switches with no spanning tree on V LAN 1 can be the case of this config a loop ???
I am using upper config on interfaces that are connected the switches  together in ring.
 
Other interfaces on switch have this config:  
int range 0/1-4
switchport mode acc
switchport acc vlan1
 
int range 0/5-24
switchport mode acc
switchport acc vlan50
 
I am using vlan1 just for local switching without connection to internet! I am asking just because i have this king of messages in logs:

%CDP-4-NATIVE_VLAN_MISMATCH: Native VLAN mismatch discovered on GigabitEthernet1/0/27 (1), with SW3560x_BR8874 GigabitEthernet1/0/19 (50).
 
GI 1/0/27 and GI 1/0/19 have this config:
switchport mode trunk
trunk aloved vlan 50

View 5 Replies View Related

Cisco Switches :: SG500 - Migrate From Default VLAN1 To Different VLAN

Mar 1, 2013

I have an SG500 that is already deployed with some Access VLANs on it. The PVID is still the default 1. I am trying to change it to 19 with as little interruption as possible. If I just go to the VLAN Management Tab and change the Default VLAN to 19 and reboot the switch, will it migrate my management IP to the default VLAN without any trouble? Would it be less interruption to: Create VLAN 19, assign it an out of subnet IP address, change a port to PVID 19, connect directly to that port, go to that IP address, remove the original management IP from PVID1, change all the ports to PVID19 then change the management IP back to the original?

View 1 Replies View Related

Cisco WAN :: 2960 - Establish Connectivity From Subnets / VLAN1 And VLAN2?

Feb 21, 2012

the attached image shows what i am trying to achieve.i need to establish connectivity from subnets 10.30.5.X and 10.30.6.X (in VLAN1 and VLAN2 respectively) to subnet 10.11.35.X
 
i have a trunk port on my cisco 2960 that is connected to GiE0/0 on my Cisco ASA that has 2 sub-interfaces with IPs in the subnets mentioned above.my problem is i can only connect to 10.30.6.X from 10.11.35.X (and vice versa), but no connectivty to 10.30.5.X

View 3 Replies View Related

Cisco Routers :: RV180 Use VLAN1 For Internal Private Network

Sep 7, 2012

My plan is to use VLAN1 for the internal private network and VLAN2 for free public wifi. My question is can I use a PC on VLAN1 to configure/manage my access points? There are no dedicated PCs on VLAN2.

View 7 Replies View Related

Cisco Firewall :: 6500 Can Shutdown Vlan1 On Switch And Still Communicate With FWSM

Jun 17, 2012

It is my understanding that the FWSM for the 6500 series switches uses a 6 port Etherchannel on the backplane to communicate with the 6500 series switch.Can you shutdown vlan1 on the switch and still communicate with the FWSM? I was under the impression that you could not (although I am looking at a config with it shutdown)

View 1 Replies View Related

Cisco Switching/Routing :: 28672 Two Root Bridges VLAN1 Rapid-pvst

Apr 1, 2013

I have two locations DC and Corp connected to each other via Point to Point Circuit.  I have forced the two core switches setup as GLBP pair to be primary and secondary for certain VLAN's including VLAN1.I have a switch in our Corporate office 3750 which is where the point to point circuit terminates.  VLAN1 SVI is manually shut on that switch.  Also the priority on VLAN1 is increased manually like this, "spanning-tree vlan 1 priority 28672". 
 
Now the issue is that the Primarey Root Bridge in the DC is the root bridge for VLAN 1.  But this other switch 3750 in our corporate office also is a root bridge for VLAN1.  [code]

View 17 Replies View Related

Cisco Switches :: SG200 To SG300 - Setup VLAN1 For Data And VLAN10 For Voice

Apr 8, 2013

I have a customer with several SG300's providing VLAN1 for data and VLAN10 for voice. The PC's are piggy backing off the phones and showing up in the SG300 fine:
 
One department has recently employed more people so we have an SG200 switch to connect the computers and phones to. I don't seem to be able to get any connectivity between the new switch and the SG300 it is connecting to. I have setup VLAN1 and 10 as per the images below:

View 4 Replies View Related

Cisco Switching/Routing :: 877W - Multiple Static Routes / Same Destination Dialer0 And Vlan1?

Jun 10, 2013

Is there any way to have my Cisco 877W Router alter from using one static route to another static route when another router on the network is reporting destination host unreachable?
 
Router 1 (192.168.2.253)
Dialer0 -> ppoe to internet
Vlan1 -> local 192.168.2.0/24
 Router 2 (192.168.2.254)
Dialer0 -> ppoe to managed VPN (172.16.28.1)
Vlan1 -> local 192.168.2.0/24
 
Router 2 is connected to another network through a managed VPN and that network also has internet access. I want to be able to have two routes to the internet on Router 2. And when Router 1 internet goes down packets get routed through the VPN instead.
 
I currently have on Router 2
 
ip route 0.0.0.0 0.0.0.0 192.168.2.253
ip route 10.0.0.0 255.255.255.0 Dialer0
ip route 0.0.0.0 0.0.0.0 172.16.28.5 250
 
Which does nothing when Router 1 has its Dialer0 interface shutdown, or goes offline completely.I suspect I could reverse the setup and have everything routed through the VPN by default and then if / when Dialer0 interface goes down it would switch to using Router 2, but if the problem is in the remote network and interface Dialer0 stays up, it would probably do the same thing... nothing.All devices mentioned are Cisco 877W routers with ADSL and a bunch of fast ethernet interfaces.

View 2 Replies View Related

Cisco Firewall :: Change Default SSH Port On ASA 5505 (port Forwarding)

Dec 2, 2011

So here is my network.
 
ASA5505--->Cisco1841--->Cat2960
Code
ASA asa831-k8.bin
Cisco 1841 c1841-adventerprisek9-mz.151-4.M2.bin
Cat 2960 c2960-lanbasek9-mz.122-55.SE1.bin
 
and here is my dilemma.
 
I can SSH from the internet to my ASA on default port 22, directly to my public IP.  I can SSH from the internet to my Cisco 1841 on port 2001. I can not however, SSH to my Cat 2960.  From what i can tell, on the Cat2960 i can't change the default port 22 for SSH to different port, just like i did on the Cisco 1841.  I looked to see if I can change the default port for SSH on he ASA, it does not look like this is an option.
 
The bottom line is that i want to be able to SSH to all three devices from the internet.  I only have one public IP.  As of now, what i can do is only SSH to the ASA on default port 22 directly to the public IP and Cisco 1841 on port 2001.  It appears that changing the default SSH port on Cat 2960 is not an option.  It also appears that I can't change the default SSH port on the ASA, if i could, i would and then i should be able to SSH to the Cat 2960 on port 22. No matter what i did on the ASA, it always listens on port 22 for SSH connections.
 
show asp table socket
TCP       001f549f  <<pub IP>>:22              0.0.0.0:*               LISTEN
 
how do i make it listen on different port?
 
Here is relevent config for SSH for cisco 1841 (port forwarding)
 
ON ASA
object network ROUTER
host 10.10.1.1

[Code].....

View 28 Replies View Related

Cisco WAN :: Change Password On 877-K9?

Mar 23, 2011

How can I change the password on my Cisco 877-K9?

View 5 Replies View Related

Cisco WAN :: 1234 Change AD In BGP

May 21, 2013

Is there any way to change the AD for an inbound eBGP routes to match with route-map instead of ACL? I know I can do that with ACL as follows and it works, but it is not scalable and if there is a way I can match AS Path or Community via route-map and then change the AD for those that matches, that will be ideal.  So far I found the command to change AD was only with ACL as option.router bgp 1234.where 1.1.1.1 0.0.0.0 is the ebgp neighbor ip address and 1399 is the ACL 1399 and 120 is the AD to change the eBGP from 20 to 120. 

View 5 Replies View Related

Cisco :: IP Address Change On CSM 3.3.1?

May 8, 2013

How to change the IP address of a Cisco CSM 3.3.1 ?

View 0 Replies View Related

Cisco AAA/Identity/Nac :: ACS 4.2 - How To Change IP

Mar 19, 2011

My customer has to change the ip address of one of the ACS server that is in production. In my opinion change in ip address would cause AAA client information in ACS gui to update and point to new ip address automatically.
 
2nd I do not see any download image available on CCO for ACS4.2. There was only clean access utility and patches. where can I get the ACS4.2 complete software image

View 1 Replies View Related

Cisco WAN :: 887 Command Change

Mar 15, 2011

I have recently up swapped out an 877 router for an 887 router and have copied the config template accross however it will not take 3 of my commands.
 
AAA accounting system default stop-mly group tacas+
ip inspect name firewall cuseeme timeout 3600
dsl operating -mode auto

View 2 Replies View Related

Way To Change WEP Key

Mar 14, 2011

I have installed a Netgear N300 and want to change the WEP key as it is too long.

View 7 Replies View Related

How To Change DNS

Oct 2, 2012

I know how to change my DNS but need to know which ones are public, So i wasn't satisfied with the speeds i was getting a ran a free scan of all the DNS servers in my area and benchmark-ed which was fastest (the tool is called (DNS benchmark) and i found a REALLY fast one.

View 5 Replies View Related

How To Change From WEP To WPA

Jan 25, 2012

how to verify if am having WEP or WPA network currently ? Assuming most of us have WEP by default, how can change it to WPA ?

View 3 Replies View Related

Cisco :: 4500 Won't Change To SSO Redundancy

Sep 6, 2011

I have a 4510R+E switch that won't change to the SSO redundancy mode. After entering the 'mode SSO' command, the switch reboots the peer supervisor (as it says it will), but after it comes back up it remains in RPR mode. I've tried rebooting the peer supervisor manually, rebooting the entire chassis, manually power cycling the entire chassis, and reseating the sups, but the switch remains in RPR mode. The issue started when I swapped the switch's supervisor with the supervisor of another 4500. The same issue was observed on the other 4500 as well, but after several reboots, I got it to change to SSO mode. Prior to the swap, both switches were running in SSO mode just fine.Since we're running IOS version 15.0 with the 'spare sup' license, I suspect the issue arose because of licensing complications (with relation to the chassis serial number and the like) when I swapped the sups....although this doesn't explain why the other switch changed to SSO after some troubleshooting.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved