Cisco WAN :: 1234 Change AD In BGP
May 21, 2013
Is there any way to change the AD for an inbound eBGP routes to match with route-map instead of ACL? I know I can do that with ACL as follows and it works, but it is not scalable and if there is a way I can match AS Path or Community via route-map and then change the AD for those that matches, that will be ideal. So far I found the command to change AD was only with ACL as option.router bgp 1234.where 1.1.1.1 0.0.0.0 is the ebgp neighbor ip address and 1399 is the ACL 1399 and 120 is the AD to change the eBGP from 20 to 120.
View 5 Replies
ADVERTISEMENT
May 26, 2013
Is it possible to convert multicast streams (224.0.0.1:1234) to unicast (Receiver 10.0.0.1:1234) at the router level.
View 4 Replies
View Related
Apr 8, 2012
I can't get access to my router. Won't accept admin password or 1234 .
View 3 Replies
View Related
Mar 23, 2011
How can I change the password on my Cisco 877-K9?
View 5 Replies
View Related
May 8, 2013
How to change the IP address of a Cisco CSM 3.3.1 ?
View 0 Replies
View Related
Mar 19, 2011
My customer has to change the ip address of one of the ACS server that is in production. In my opinion change in ip address would cause AAA client information in ACS gui to update and point to new ip address automatically.
2nd I do not see any download image available on CCO for ACS4.2. There was only clean access utility and patches. where can I get the ACS4.2 complete software image
View 1 Replies
View Related
Mar 15, 2011
I have recently up swapped out an 877 router for an 887 router and have copied the config template accross however it will not take 3 of my commands.
AAA accounting system default stop-mly group tacas+
ip inspect name firewall cuseeme timeout 3600
dsl operating -mode auto
View 2 Replies
View Related
Mar 14, 2011
I have installed a Netgear N300 and want to change the WEP key as it is too long.
View 7 Replies
View Related
Oct 2, 2012
I know how to change my DNS but need to know which ones are public, So i wasn't satisfied with the speeds i was getting a ran a free scan of all the DNS servers in my area and benchmark-ed which was fastest (the tool is called (DNS benchmark) and i found a REALLY fast one.
View 5 Replies
View Related
Jan 25, 2012
how to verify if am having WEP or WPA network currently ? Assuming most of us have WEP by default, how can change it to WPA ?
View 3 Replies
View Related
Sep 6, 2011
I have a 4510R+E switch that won't change to the SSO redundancy mode. After entering the 'mode SSO' command, the switch reboots the peer supervisor (as it says it will), but after it comes back up it remains in RPR mode. I've tried rebooting the peer supervisor manually, rebooting the entire chassis, manually power cycling the entire chassis, and reseating the sups, but the switch remains in RPR mode. The issue started when I swapped the switch's supervisor with the supervisor of another 4500. The same issue was observed on the other 4500 as well, but after several reboots, I got it to change to SSO mode. Prior to the swap, both switches were running in SSO mode just fine.Since we're running IOS version 15.0 with the 'spare sup' license, I suspect the issue arose because of licensing complications (with relation to the chassis serial number and the like) when I swapped the sups....although this doesn't explain why the other switch changed to SSO after some troubleshooting.
View 1 Replies
View Related
Aug 2, 2012
a) one router with two ethernet interfaces (LANs) and a serial interface. The serial interface is connected to the internet, dynamic nat is used for hosts in the two lans. A web server has a private address of 172.168.50.10 and it is being translated to the internet with serial's interface 68.32.x.x (public ip) with static nat. Clients in the internet type the public address to access the web server.
b)Problem: clients inside the LANs cannot access the web server by typing the public address, they use the server's private address instead, this create a problem with DNS static entries in the HOSTS file in the OS. It is a test server and is only available to authenticated users (lock and key ACLs), so no need to make a real DNS record. The entry in the HOSTS file points to the public address.
c)Question: how can a create a route map to change the public address in the HOST file to the private address of the test web server everytime a user in the LANs type the domain name.
View 6 Replies
View Related
Dec 18, 2012
i'm going to change all of my old switches in CED with new ones 2960-S. I was reading about Flexstack Cisco technology is able to group from 2 up to 4 switches into one logical switch.I just have a doubt about my environment. Master switch in stack replaces the same configuration to all slaves switch into cluster. But if i would have different access vlan on different switch how could i proceed?
View 4 Replies
View Related
Oct 30, 2012
Just implemented a couple of replacement DNS servers so decided to test by disabling existing Server DNS services only (10.0.0.21)Two problems arose from this, first was I lost access via the ASDM, second was remote access failed. The Cisco VPN client worked but RDP could not find the remote access Server.I've replaced the DNS settings everywhere I could think on on the ASA so decided to check the running config and noted these lines that refer to old DNS.Would this suggest the cause for the RDP, although looking at the various group policy areas on the ASA I could not locate any reference to 10.0.0.21/22, am I missing something?
View 1 Replies
View Related
May 11, 2012
We're running ISE 1.1 for guest services. We use Active Directory for Sponsor Portal login, as well as for administration of the ISE itself. Our corporate policy requires a password change for service accounts, and the service account password we use for ISE to connect into AD expires in a few days. So I changed the password on the account, but how do I tell this to ISE? I don't see anything in the documentation, only some references to only use non-expiring accounts to connect to AD. This made me laugh. If our corporate policy was that lax, we'd never have purchased ISE.
1) Is there a way to communicate this to ISE? Or is leave and then join the only way? Will that even work?
2) I see that after the password change, ISE continues to work fine. Does it only synch with AD periodically? On reboot, or every X hours? Right now things are working, but I'm afraid as soon as I turn my back it will stop.
View 2 Replies
View Related
Mar 26, 2012
i have cisco 880 with NPE licence, but i need encryption on this device. I change IOS to c880data-universalk9-mz.151-3.T1.bin, but i still have NPE License and only Evalution without NPE. How can i have permanent license?
show license all
License Store: Primary License Storage
StoreIndex: 0 Feature: advsecurity_npe Version: 1.0
License Type: Permanent
License State: Active, Not in Use
[code]....
View 3 Replies
View Related
May 28, 2011
I have four ASA 5505 devices connected via tunnels. All of the tunnels have a single point of exit to the outside, an AT&T T1 line. Because of issues with bandwidth, I added a secondary line to each site. In this case the secondary line is a comcast high speed internet connection. What I would like to do is set up a route so that any traffic that is going to the internet (browser or email) be directed through the Comcast line and all internal traffic (file transfer, ERP, VOIP) can be directed to the AT&T line. Each has a separate ip address. There is a single default gateway set up on the ASA now.
View 1 Replies
View Related
May 30, 2012
I'm looking to make a few adjustments to out wireless network and need to change the RF channels on a few APs.I've logged on to NCS went into the AP, an 1142N, then the Radio 802.11 b/g/n and changed the RF channel under custom.Once I pressed the save button the channel reverts back to its original channel. I've also tried this on a 1242AG the same thing happens. I then went to the controller and tried to change the RF channel there and it took the change. I pressed apply logged out went back to NCS made the change under custom and again it reverted back after I pressed the save button. I went back into the controller and the channel had also reverted back even thought it gave the impression it took the changel.
View 1 Replies
View Related
May 30, 2011
How can I change the IP Address of cisco ACS 5.2 itself through the web?
View 3 Replies
View Related
Dec 27, 2009
In default mode the ASA 5505 is setup with two Vlan's, one inside and one outside. Vlan1 is the default inside VLan, with IP 192.168.1.1. I would like to change the subnet of Vlan1 tot 192.168.10.1, but when I do, no Ethernet port is assigned to Vlan1 anymore (was 0/1 - 0/7). What I have done is;
#config t
(config)#interface vlan 1
(config)#ip address 192.168.10.1 255.255.255.0
But after that, no Ethernet port is within Vlan1, so I tried the following to assign one (port 0/1);
#config t
(config)#interface 0/1
(config)#switchport access vlan 1
(config)#no shut
But nothing happends when monitoring (#show run) interface 0/1 (no Vlan assigned)
View 6 Replies
View Related
Feb 1, 2011
Where I can find the change logs for the ADSL Firmware's.I realize each firmware comes with its individual bug fixes, however there is usually a significant difference between the shipped firmware and latest firmware available.i.e. the 877m is shipped with 3.0.14 and the latest is 3.0.33. We have a handfull of miscellaneous issues, across a variety of hardware and customers, and would like to scan through the change logs to see if any of these issues were addressed by a previous bug fix.
View 2 Replies
View Related
Jul 14, 2011
I need to change my mac address / clone another on my network for my internet to work and have been goggling but no answers ?
View 1 Replies
View Related
Nov 19, 2012
so I have my router that's connected to outside world (internet) and it's also connected to my company.I want to create a nat rule that basically says when I go to my company don't nat but when I go on the internet nat.now I do this with this statement [code] I want to do the same thing but this time with this rule. ip nat inside source static tcp 10.181.20.84 22 interface FastEthernet4 2222 this rule doen't work from the company to my router but it works from the internet to my router...
I just can't find the way to change this ip nat rule and use my same 110 ACL.basically with this last rule when I try to connect to my router from the company it tries to nat it back to the ip of the router interface ... it should not nat when I go from the company but nat when I connect from the outside internet.
View 5 Replies
View Related
May 21, 2013
When I attempt to change the pre-shared key for our wireless network "Engineering" I get an error that states ERROR" VLAN '122" doesn't exist on 'Radio1-802.11N 5GHz" (see Services> VLAN). When I check the vlan the box for the 5GHz radio is checked. let me know what the possible cause is? Here is the config:
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
[Code].....
View 3 Replies
View Related
Jun 8, 2012
I need to change the source IP of a packet for one of my NAT's.I currently have an Cisco 1812.I have an PPPoE connection as Dialer 0.I have another VLAN that is connected to an Netscreen SSG5 VPN gateway via another Cisco switch.I have a vlan trunk between the switch and the 1812. What I would like to achive is the following :-For any traffic going to the following three ranges make it apear as if it was coming from the VLAN50 address [code]I can ping my netscreen on 10.27.30.255 fine from the Cisco 1812. But any other PC fails, as for some reasion the traffic has a source of my Dialer 0 interface.How can I write a nat to change the source just for the tree destitnations ?
View 7 Replies
View Related
Aug 23, 2012
I'm trying to change the IP address of the smtp server on cisco LMS 3.2.1;I have changed the IP on the GUi and when it didn't work, in the regdaemon. xml file, but it did not work too;When I capture packets from the LMS, it still sends emails to the old IP;
View 1 Replies
View Related
Sep 10, 2012
I have configured the NCS 1.1.1.24 and its running fine, but i used the IP address 10.18.20.7(it was the WCS server), but now I want to use 10.18. 20. 8 (NCS Server) ip address.
so what should i do to change the ip address: I know only 1 thing that is, change the ip of the interface gig 0 .My main task is to run WCS and NCS parallal.
View 1 Replies
View Related
Dec 6, 2010
There is a site I oversee that is moving to a new ISP. The drive is 2 hours round trip and I need to do is change an IP. DHCP is being handed out by the internal Domain Controller and all the workstations point to the server for DNS. Will the following commands inputted over an SSH putty session into the current WAN IP change the IP and allow me to hookup to the new ISP? The plan is to copy and paste the following commands into global config mode. Currently they are using DHCP on the WAN side which I do not approve of and their external route is pointing to the internal IP of 192.168.1.1. Things still work but I want to do away with this. Will these commands get the job done?
interface vlan 2ip address 68.x.x.2 255.255.255.240exitno route outside 0.0.0.0 0.0.0.0 192.168.1.1route outside 0.0.0.0 0.0.0.0 68.x.x.1
View 7 Replies
View Related
Oct 16, 2012
I have just started supporting a client with a Cisco 1760 on site. They also use the VPN on this device. I can get to the web interface but for the life of me I cannot find out where I change the VPN password. They just terminated an employee and I need to do this.
View 13 Replies
View Related
Sep 25, 2011
I want to change the management IP of our wireless controller, I have 5 LAP1142N connected to this controller.
I have a few questions before I will do this task.
1. If I change the management IP, will the controller need a reboot?
2. Will the AP's automatically sync with the new management IP?
3. Do I need additional configuration on the AP's?
4. What else do I need to consider.
View 9 Replies
View Related
Jan 19, 2011
We have a WCS 7.0.164.3 with 27 WLCs. We are now running a project where were creating new subnets on our locations - and because of this we have to change the controllers management ip-adresses.
I am able to change the ip-address of the management interface both through wcs and on the wlc, but the controllers ip-address (the one we see under Configure - controllers) is still the old one. This causes the wcs to loose connection to the wlc. I have to delete the controller, and then add it with the new IP. The APs are then removed from the maps, and I have to manually place them on the maps again - this is a lot of work with 700 APs.
Is there a way to change the controller IP in WCS?
View 6 Replies
View Related
Nov 13, 2011
I have a 2900 ISR that my VPN clients connect to using IPSEC over UDP. I am having periodic problems, especially with clients connecting through DSL, where they connect and immediately drop. Sometimes this is resolved by users updating their home router firmware. I'd like to issue a new client PCF file using IPSEC over TCP to see if that resolves the problems.
Can I have both running at once, and what do I need to add to the 2900 to enable this connectivty without breaking the existing clients? If the test is successful, I will migrate all users to the new configuration. This ISR is also used to support L2L connectivity for a handful of sites.
View 1 Replies
View Related
Oct 27, 2011
How can I edit a static interface IP address? I don't seem to be able to edit the static IP address for my switch. How do I go about changing it? As you can see the IP Address field is not editable.
I have also upgrade to the latest firmware and I cannot figure out how to edit it via that as well.
View 1 Replies
View Related