Cisco WAN :: Interface Status On Router 887VA
Apr 29, 2013
I have cisco router 887VA.Question is when i connect that WAN port ( eth0) with any switch or laptop/pc i do not see the port in up state. What can be the reason.I have done "no shutdown " on interface level and there is no configuration on interface except the IP address , but it show " up down "state even the port is connected to some device. ( Is the port is faulty or some other reason).As per my concept it should show up state when we connect to some device ( Like router / switch / laptop).
View 6 Replies
ADVERTISEMENT
Mar 24, 2013
I wish to assign a MAC ACL to a layer 2 interface on an 887VA router but cannot seem to see how to do this.
View 2 Replies
View Related
Mar 4, 2012
I have 5 to 6 878 routers and in all these routers the ATM interface is stuck up with initializing mode. This is the IOS running on it c870- advipservicesk9-mz. 124-15.T9.bin
View 1 Replies
View Related
Aug 24, 2012
Just got hold of my first 887va for my home, never configured a vdsl interface before and was just wondering if my setup looked good to someone whos done it a few times.
View 6 Replies
View Related
Feb 18, 2011
On my Switch (3750), i have a host connected. Checked the interface status and it shows as "connected". However, when i tried checking the MAC connected to that interface, its not showingI have my Switch (3750) connected to a Router (3845). On the Switch, i have a printer connected in an interface. I am seeing the Printer's MAC associated with the switch port. However, when i checked the ARP table; no entry seen for the Printer's MAC. What are the possible reasons for this? We have several same kind of devices connected to network and they are fine.
View 5 Replies
View Related
Oct 27, 2012
I do terminal monitor on my 4500 switch.I can't see the status of the interface ( when it become up or down)What is the problem? I need to add a command?
View 3 Replies
View Related
Aug 25, 2011
We have two autonomous access point 1142 series running 12.4(21a)JA1 and randomly the Dot11Radio0 interface goes into reset/down state. At first I thought it was something related to power consumption issue on the switch, but looking at the remaining (w) I have plenty.
View 8 Replies
View Related
Feb 28, 2013
I have a AIR-LAP1131AG-A-K9 this Ap is registered but, i cant enabling admin status on interface B/g, when select option throws a error. "Error in Enabling Admin Status"
View 4 Replies
View Related
Nov 29, 2012
This is regarding an issue with one of my access point. The access point 1252 is autonomous one running the IOS version C1250 Software (C1250-K9W7-M), Version 12.4(10b)JDA3, RELEASE SOFTWARE (fc1)
The status of the dot11Radio 0 interface is showing as RESET. I have pasted the interface brief details below.
ap03#
ap03#
ap03#sh ip int brief
[Code].....
View 10 Replies
View Related
Mar 5, 2013
I have a really weired thing happening on 6509 device with one of my customers.The device has a SUP 2 (MSFC2) with version 12.2.18SXF17B.
any VLAN interface once administratively down or simply down shows on "show interface status" output as VLAN.While it supposed to show "Routed". However once the port is up it is shows "routed" like it should.
View 5 Replies
View Related
Aug 30, 2012
difference of CISCO887VA-K9 and CISCO887VA-SEC-K9.I thought it because of the Advanced Security and Advanced IP Licenses, but it isn't, I've got the -SEC- Version now just with the Advanced Security license. So I asking myself why I bought the more expensive CISCO887VA-SEC-K9 if I have to buy the additional Advanced IP Services licenses extra..
View 14 Replies
View Related
Mar 25, 2013
Is there a GUI that can be used to setup the 887 router. I need to setup a VPN.
View 1 Replies
View Related
May 6, 2013
i have set up a layer 2 tunnel on my 887va router and the traffic transmits accross this to my second 887va. unfortunately, I do not seem able to get the layer 2 traffic from my host PC and down the tunnel.
I believe the problem to be the router settings for the fastethernet aqnd forwarding this data out of the dialer port.
Here is my config:
Building configuration...
Current configuration : 3973 bytes
!
! Last configuration change at 13:03:15 UTC Thu May 2 2013
[Code].....
View 6 Replies
View Related
May 12, 2013
does a router Cisco 887 va k9 support EIGRP and IPsec ?
View 2 Replies
View Related
Jul 7, 2011
I have been trying to connect a new Cisco 887VA Router to the Internet using ADSL via PPPoE and have been unsuccessful. The DSL line is active and functioning correctly since the current "old" router is connected and working without any problems (the "old" DLink router is connected to an Alcatel DSL Modem). AT&T provides the ADSL service to the office. When the Cisco Router is connected it tries to negotiate a connection via PPPoE on the WAN interface but utlimately fails. The IP for the WAN interface is dynamic.
Below is the current configuration of the router.
!
! Last configuration change at 00:43:54 UTC Sun Jun 26 2011
!
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
[code]....
View 9 Replies
View Related
Jul 22, 2012
I'm having some problems getting an ipsec tunnel established between a cisco 887VA router and a cisco srp527w router.I am working from a few text books and some example materials. I have worked through many combinations of what I have got and am still struggling a little bit.I look at debug results and it appears as though the policies do not match between the devices:
Jul 23 05:44:37.759: ISAKMP (0): received packet from XXX.XXX.XXX.XXX dport 500 sport 500 Global (R) MM_NO_STATE
broute1#
Jul 23 05:44:57.079: ISAKMP:(0):purging SA., sa=85247558, delme=85247558
broute1#
Jul 23 05:45:17.031: ISAKMP (0): received packet from XXX.XXX.XXX.XXX dport 500 sport 500 Global (N) NEW SA
[code]....
Some specific questions:
1) on the SRP in the example's I have used (and I have a few SRP->SRP VPN's that work) I see you need to enter the preshared key, I'm not seeing in the examples I have used anything about the IKE preshared key on the IOS box. Any examples where you use the preshared key for IKE? I wonder if this is my primary issue as it states clearly in the log that there is no Preshared key :|
2) I have used a mish mash of names between the various sections as on the SRP the naming convention isnt the same; ie: which parts of the IPSEC negotiation come from the IKE policy section and which from the IPSEC policy section. Do the names really matter across different ends of the VPN?
3) I notice when I perform this command in the(config-crypto-map)#:
set peer FQDN
It is converted to:
set peer XXX.XXX.XXX.XXX
Is this expected? I want the device to look at the FQDN as this particular host is using DDNS and not use a static IP address.
View 4 Replies
View Related
Feb 11, 2012
I've got problem trying to connect the CISCO-887VDSL/ADSL OVER POTS ROUTER to internet. Only got the LAN part working.I'm trying to setup PPPoE with dynamic IP Followed CISCO's documentations but the commands used were not recognized by the router.
here's my config.
!
! Last configuration change at 08:31:51 UTC Sat Feb 11 2012
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[code]....
View 1 Replies
View Related
Dec 6, 2012
We have a remote site connected to ADSL line with a Cisco 887VA router attached. This has been working fine for the last couple of months. However, recently, the site have started to complain of performance issues (network slow, applications disconnecting, etc)Looking on the router, we can see evidence of packet loss/timeouts from a simple ping to the internet e.g. [code]
However, we have logged the fault with our service provider and they return all line tests as clear but what is particularly strange is that they also report “and the SNR Margins are well within threshold levels (Upstream 11.5 and Downstream 15.0)” which, unless I’m misunderstanding something, seems to be completely different from what the router itself is reporting.Is there a reason why the service provider’s stats for Noise Margin would appear to be so different from what the router is reporting?
View 2 Replies
View Related
Mar 18, 2012
I think change to c7206xvr G2's. Because I have got 2 GB active traffics. I will buy c7600 router. But I saw c7600 routers since 2001 for the referance guide. When is it c7600 router end of life time?How do I chose equipment?
View 7 Replies
View Related
Nov 4, 2011
I am trying to setup my E4200 to my new Cable Modem. I followed all of the procedures. I get Internet access when plugged directly to modem. I cloned the MAC Address and the Stus of the Router displays my current IP's (so I should have Internet). However, when I plug my computer into the Router I get no internet access.
View 3 Replies
View Related
May 9, 2012
i have a 1841 cisco router and i recently purchased a 1 port HWIC wan interface card. My problem is that I cannot see the interface in my config file. Is there something i am missing?
View 8 Replies
View Related
Jul 24, 2011
give us the option to disable the front status led too.
View 9 Replies
View Related
Feb 7, 2013
We just recently purchased a 3945 ISR G2 router and have a SRE-910 module (with two hard drives) configured in a Raid 1. We are running a stand-alone version of ESXi on the service module and I'm trying to figure out how to monitor the status of the Raid on the drives (along with other health issues). SNMP has revealed nothing so far and even opening a support case for which MIB's to use has proved fruitless. All the documents I find on monitoring the modules say to use LMS which is now Cisco Prime. I've downloaded the trial copy, put in the SNMP settings and scanned the router. I get device results and it shows that I have the SRE-910 module installed, but I get no other configuration / device informaiton from the module itself.
I tried to create a new Monitoring template using the NAM health as the base template (which I'm assuming this is the correct template). Unfortunately, when I actually try to deploy the template against the discovered router, I get an 'Unexpected end of list' error which makes me assume I'm still doing something wrong.
View 1 Replies
View Related
Dec 29, 2010
We have cisco 7600 Router with 76-ES+XT-4TG3C Module connected. The Module is getting detected after upgrading the Router with SRD5 IOS.Below are the testing which we have done on the Router but we are facing the issue while configuring the Transport mode LAN and Transport Mode WAN:Brief about this is:- 2 Cisco 7606-s Router with Module 76-ES+XT-4TG3C each.- two ports on 7606-s Ten2/1 & Ten2/2 are configured as a Transport mode WAN while Ten2/3 & Ten2/4 are configured as Transport mode LAN.- We connect Fiber Cable from LAN Port to MUX and from MUX to 2nd LAN Port of the same Router. Same thing we tested by using the WAN Port-MUX-WAN Port connection.- Now on MUX end LAN port, connected Single and Multi mode fiber and on 7606 end 2/4 port which is configured as transport mode LAN, using Multimode SFP module -> XFP-10G-MM-SR, port did not came up then replaced 2/4 port with single mode SFP ->XFP-10GLR-OC192SR port came up. this is testing for LAN.- For WAN testing on MUX end used WAN port and on 7606 end checked with single mode and multimode fiber and with single XFP-10GLR-OC192SR / mulimode XFP-10G-MM-SR SFP, port did not come up.Wanted to know 1) If we have to go for Transport Mode LAN then which SFP/XSFP Module should go with along with the Single/Multimode Fiber.2) If we have to go for Transport Mode WAN then which SFP/XSFP Module should go with along with the Single/Multimode Fiber.Anything else is required while configuring the Transport Mode WAN as this is for Packet-Over_SONET/SDH? 3) MUX Side change is required while connecting both of this Modes on Cisco 7600 Router.4) Is hardware of the Router is giving any issue? Though we tested by connecting Back to Back LAN Port as well as Back to Back WAN Port. In both the situation the Ports are coming UP.
View 1 Replies
View Related
Apr 9, 2011
Is it possible to set up a WAN interface on a FastEthernet interface of a Cisco 877 Adsl Router ?Due to my ISP, i've to use an external VDSL modem and must connect it to my cisco 877 router (and leave it's adsl interface unused).But i don't know how to set up a wan port, other than the adsl interface itself (dialer0), on my cisco.
View 7 Replies
View Related
Jan 12, 2013
I am trying to connect my DIR 815 router to a DSL modem.
I fill out the password, and the username the way it should be, but then when I try to get the modem to connect, it says the network status is busy.
View 1 Replies
View Related
Sep 26, 2010
My wireless connection for my laptop is showing upas N on Win 7 but G on DIR-655 status page??? I'm confused. Am I getting N speeds/coverage or stuck with G. If G, why? I've tried wiping my wireless network config. on Windows and reestablishing it, but no change. The DIR-655 config page shows my machine connected at 54 Mbps and Type as G
View 8 Replies
View Related
May 9, 2013
I cannot get access into my router because it doesn't seem to have a gateway IP address, although it is assigning my computer an IP address.
View 1 Replies
View Related
Oct 31, 2011
I'm thinking of upgrading from my Linksys WRT54G router to the E4200 and though I've goggled. Also, are there no LEDs on this unit to tell you the status of what's connected?
E3000WRT-54GWVC-80N
View 3 Replies
View Related
Dec 18, 2012
I have the Linksys EA6500 with the latest firmware and have a question regarding the device list connection status.Currently, I am seeing devices in the list that have a connection status of live, but they are not even within my home network. What is the update/cycle time for the device list actually checking connection status of a device?In my situation, it has been 3 days (72 hours) since the two device showing as connected have not been connected to my home network/router. Noticed that this inaccurate connection status for these devices is also contributing to the Device Monitr app not showing correct device connection status info.
Would like to have real-time device connection status if possible. This device list is great way to know when device get connected or disconnected which let me know when my kids get home from school or using game console when should be doing homework.
View 7 Replies
View Related
Apr 5, 2013
I cannot access my Motorola SB6141 cable modem status page at 192.168.100.1 thru the EA6500 router. I can bypass the router and can connect to the status page with no problem. Is there a setting to change or can I possibly do port forwarding to access it?
View 9 Replies
View Related
Mar 3, 2012
Have they changed the poe requirements for this router? This model seems to be a seconed gen 887 with internal wireless, fanless and instead of there being a second 2 pin power socket for the poe option there is just 1 power input with the text under is saying. 'poe option requires 5a power adapter' I have purchased the 800-IL-PM=2 to delivery poe on the first 2 ports from this document [URL]While the daughter board does fit in the stand off pegs are too short and the power adapter is incompatable.
View 9 Replies
View Related
Apr 1, 2011
I'm trying to get an internet connection through my cisco 877va but I can't get access. I cant apply show cotroller vdsl 0 command and I can see DSL up, however, the dialer0 interface can't get access to internet. If I apply "show int dialer0 account" coomand, I get the next message: "No traffic sent or received on this interface". [code]
View 14 Replies
View Related
