Cisco WAN :: 887VA ADSL Over Pots Router And PPPoE With Dynamic IP?
Feb 11, 2012
I've got problem trying to connect the CISCO-887VDSL/ADSL OVER POTS ROUTER to internet. Only got the LAN part working.I'm trying to setup PPPoE with dynamic IP Followed CISCO's documentations but the commands used were not recognized by the router.
here's my config.
!
! Last configuration change at 08:31:51 UTC Sat Feb 11 2012
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
I have been trying to connect a new Cisco 887VA Router to the Internet using ADSL via PPPoE and have been unsuccessful. The DSL line is active and functioning correctly since the current "old" router is connected and working without any problems (the "old" DLink router is connected to an Alcatel DSL Modem). AT&T provides the ADSL service to the office. When the Cisco Router is connected it tries to negotiate a connection via PPPoE on the WAN interface but utlimately fails. The IP for the WAN interface is dynamic.
Below is the current configuration of the router.
! ! Last configuration change at 00:43:54 UTC Sun Jun 26 2011 ! version 15.1 no service pad service timestamps debug datetime msec service timestamps log datetime msec service password-encryption
We have a remote site connected to ADSL line with a Cisco 887VA router attached. This has been working fine for the last couple of months. However, recently, the site have started to complain of performance issues (network slow, applications disconnecting, etc)Looking on the router, we can see evidence of packet loss/timeouts from a simple ping to the internet e.g. [code]
However, we have logged the fault with our service provider and they return all line tests as clear but what is particularly strange is that they also report “and the SNR Margins are well within threshold levels (Upstream 11.5 and Downstream 15.0)” which, unless I’m misunderstanding something, seems to be completely different from what the router itself is reporting.Is there a reason why the service provider’s stats for Noise Margin would appear to be so different from what the router is reporting?
I'm trying to configure an 887VA for a pppoe ADSL2+ connection with no luck.I know the ISP requires pppoe (LLC), and the pvc is 8/35. The CD light is on, and the line is up, but the 887 just won't connect
We are trying to take ADSL interface into another VRF i.e (ip vrf forwarding VRF2 under dialer interface), the ip address negotiated command disappears, and although the dialer interface becomes up-up state, the adsl interface does not get an IP address dynamically.
Tried:
1) to reenter ip address negotiated again after changing the vrf of the interface, still the dialer interface shows "no ip address" under configuration
2) ppp ipcp accept-address again does not work.
the IOS version:c880data-universalk9-mz.151-2.T1.bin
I've struggled now for a couple of days to setup a PPPoe connection on our cisco 887va box. I can setup straight away on a draytek box so i know the connection is good.I can't get the line protocol to come up? It's connected via ethernet port 0 to an external modem. One thing i can't figure out is if ethernet 0 and fast ethernet 0 is the same physical port?I've attached the running-config below.
Im new to Cisco equipment and weve just upgraded to a all singing 8000 series (887VA) to be precise.
i'm having difficultys in setting the router to connect to our BT ADSL2 business broadband, we have a static IP but on normal cheaper routers you just input a Chap username and password. and the router sorts the rest.
i've followed the tech support from cisco website inputted the configure commands to create the ATM0 and a Dialer0 but still having no joy.when you log into the gui it only shows you a enable PPPoE tick box. no signs of PPPoA?
The aDSL circuit is up and connected and I can reach the internet, however not all sites on the internet are reachable. This is occurring on two seperate 887VA’s and the circuit has been tested with a netgear router and no issues occur. The router has been tried on 5 different ADSL connections and the same problem occurs although more websites can be reached on a home broadband connection (ADSL2+ Annex A) as opposed to the problem being more severe on an ADSL2+ Annex M circuit. The problem seems to affect websites that are full of adverts more than sites that have single domain landing pages.
The sites that I cannot reach are pingable. This happens on multiple machines behind the router. The same config is used on an cisco 877-M router with no issues.
! Last configuration change at 14:52:30 UTC Wed Feb 13 2013 version 15.2 no service pad
Have installed an 887VA on the end of a ADSL connection. The provider has specified EF 150 on the link. The router is configured using a Virtual Template.
If the Virtual Template has a service policy applied, we don't have connectivity to their main site - although the CD and PPP lights are lit. As soon as the service policy is removed, we have connectivity.
We've had three sites with the same problem. Two of the sites don't have QoS specified on the link but had the same problem if the service policy was applied.
I am trying to get my Cisco 2811 to authenticate four DSL connections and load balance them by attaching the four DSL to a switch (each DSL going to a seperate VLAN) and then trunking all four VLAN's to a ethernet interface on the 2811. My issue, I can not get more than one DSL to authenticate at a time, for example Dialer1 will connect and then it will disconnect and Dialer2 will connect, etc... I have the modems in bridge mode and I am using seperate user/pass for each DSL account and I have verified that the user/pass are correct.
Below is my config from the router and a couple of messages that came across the console.
*Apr 27 01:12:11.915: %DIALER-6-UNBIND: Interface Vi2 unbound from profile Di1 *Apr 27 01:12:11.927: %LINK-3-UPDOWN: Interface Virtual-Access2, changed state to down
We are using SRP527 routers with PPPoE ADSL connections. From the SRP527 we create an IPSec tunnel to our core routers (Cisco ASR). We are wanting to change the IPSec tunnels to L2TP, and I need to know if this can be done from the SRP527. I cannot find any L2TP configuration options in the setup options.Can the SRP527W act as an L2TP tunnel initiator over the ADSL PPPoE interface?
difference of CISCO887VA-K9 and CISCO887VA-SEC-K9.I thought it because of the Advanced Security and Advanced IP Licenses, but it isn't, I've got the -SEC- Version now just with the Advanced Security license. So I asking myself why I bought the more expensive CISCO887VA-SEC-K9 if I have to buy the additional Advanced IP Services licenses extra..
i have a problem with my adsl line connected on a HWIC-ADSL on router 2901 it was working good until yesterday the atm interface is down but the interface dialer is up .i connected this line into home adsl modem and the line is working good?
We're looking for recommendation of remote controllable PDUs that support a phone line connection for POTS (in case the core router is down and we need to remotely power cycle connected equipment) and RJ45 for control from the network (if the core router doesn't happen to be down).
I would like to set up a POTS Dial connection between 2 Cisco routers, using the modem card WIC-1AM-V2. I'd like to use this as an out-of-band connection to a remote site, if the primary internet connection fails. So, this setup will only be used in one direction, 1 router placing calls, the other one receiving calls.Here's my config of the receiving router:
chat-script dial "" ATZ AT OK "ATX3D T" ATS0=8 TIMEOUT 120 CONNECT C interface Async0/2/0 description out of band for network no ip address encapsulation slip async mode interactive line 0/2/0 session-timeout 5 absolute-timeout 10 script connection dial login local modem InOut transport input all escape-character BREAK autoselect ppp stopbits 1 speed 115200 flowcontrol hardware
[code]....
This config is working fine, when dialing in via a Windows Hyperterminal Dial connection. After a while of dialing I get the login prompt of the router.Now I want to have a router placing calls instead of a Windows Server. I can't figure out how to tell a router to place calls to a POTS phone number.
I have cisco router 887VA.Question is when i connect that WAN port ( eth0) with any switch or laptop/pc i do not see the port in up state. What can be the reason.I have done "no shutdown " on interface level and there is no configuration on interface except the IP address , but it show " up down "state even the port is connected to some device. ( Is the port is faulty or some other reason).As per my concept it should show up state when we connect to some device ( Like router / switch / laptop).
i have set up a layer 2 tunnel on my 887va router and the traffic transmits accross this to my second 887va. unfortunately, I do not seem able to get the layer 2 traffic from my host PC and down the tunnel.
I believe the problem to be the router settings for the fastethernet aqnd forwarding this data out of the dialer port.
Here is my config:
Building configuration...
Current configuration : 3973 bytes ! ! Last configuration change at 13:03:15 UTC Thu May 2 2013
I'm having some problems getting an ipsec tunnel established between a cisco 887VA router and a cisco srp527w router.I am working from a few text books and some example materials. I have worked through many combinations of what I have got and am still struggling a little bit.I look at debug results and it appears as though the policies do not match between the devices:
Jul 23 05:44:37.759: ISAKMP (0): received packet from XXX.XXX.XXX.XXX dport 500 sport 500 Global (R) MM_NO_STATE broute1# Jul 23 05:44:57.079: ISAKMP:(0):purging SA., sa=85247558, delme=85247558 broute1# Jul 23 05:45:17.031: ISAKMP (0): received packet from XXX.XXX.XXX.XXX dport 500 sport 500 Global (N) NEW SA
[code]....
Some specific questions:
1) on the SRP in the example's I have used (and I have a few SRP->SRP VPN's that work) I see you need to enter the preshared key, I'm not seeing in the examples I have used anything about the IKE preshared key on the IOS box. Any examples where you use the preshared key for IKE? I wonder if this is my primary issue as it states clearly in the log that there is no Preshared key :|
2) I have used a mish mash of names between the various sections as on the SRP the naming convention isnt the same; ie: which parts of the IPSEC negotiation come from the IKE policy section and which from the IPSEC policy section. Do the names really matter across different ends of the VPN?
3) I notice when I perform this command in the(config-crypto-map)#:
set peer FQDN
It is converted to:
set peer XXX.XXX.XXX.XXX
Is this expected? I want the device to look at the FQDN as this particular host is using DDNS and not use a static IP address.
PPPoE is established and I can access router from outside. But router can't ping itself and ouside and NAT isn't working as well. Main goal is to make Internet work from router.
Cisco IOS Software, C890 Software (C890-UNIVERSALK9-M), Version 15.0(1)M7, RELEASE SOFTWARE (fc2) version 15.0 no service pad service tcp-keepalives-in service tcp-keepalives-out
I just switched to DSL from cable internet and am having some trouble setting up my router with the new internet service. DSL modem-->Router-->Network with PC and PS3
ISP is ATT DSL modem is a TP-Link 8616 Router is a D-Link DIR-628
I put my ATT username and password into the router but it never completes a connection to the internet. I was able to create a soft PPPoE gateway connection through my computer using my username and password, but I want my router to do this, not my PC. How do I get my router to connect directly to the Internet connection rather than having my PC connect? My setup would be fine as-is if I just had 1 computer but I also want to go online with my PS3, and it won't connect like my PC will, even after putting the username/password in.
A PC connected to a Cisco 877 router and 877 router is connected to another router (7301) via GRE tunnel,Cisco 7301 router is a NAS server and is being used as a PPPOE server.If user create a PPPOE connection on his computer and dial with a username/pass we want to send the PPPOE traffic to 7301 router, so 877 router should pass the PPPOE traffic to 7301 and user will be able to connect,User -> 877 -> 7301(PPPOE server).
I get stuck in one case. One of my customer has two FTTH lines. I have to config PPPoE in routers. In one line I config succesfully, but one line never up. I call to ISP they ask me to config extactly VLAN id 10 in the physical subinterface. But in subinterface there is no command "pppoe-client dial-pool-number". I check the old modem FTTH, they also config VLAN 10 in Wan interface. I tell ISP why we have the same two FTTHs, but two differrent config ways. ISP says because the two line run in two different infrastructure, two different devices. I don't know how to do now? stay in customer side or ISP side. Here is my PPPoE config:
interface FastEthernet0/0 no ip address duplex auto
