Cisco WAN :: 887VA-M Basic Configuration Non Nat
Jan 3, 2013
I am struggling to get this working after spending many hours looking at it I am now completely stuck. We are upgrading from a 857W to this 887 VA-M I have some experience of IOS and the 800 series. Our 857W works perfectly using almost the same config. Our situation is that the router will sit in front of our firewall and act essentially as a simple router passing everything through to our Firewall. Nat is done at the Firewall.
We currently have the following configuration that seems to connect the the ISP fine but I cannot connect to the vlan2 port on the switch the firewall cannot connect to he internet or route anything via the Vlan2 port no pings etc.. I am using Fast Ethernet 0 as the Vlan2 port and the rest are V LAN 1 with a local network address to allow me to connect a laptop.
We have a block of static IP addresses, the base of which is assigned to the V LAN 2 interface and used by Dialer 0 as IP Unnumbered. Config below.
4590 out of 262136 bytes
! Last configuration change at 17:42:06 UTC Thu Jan 3 2013
! NVRAM config last updated at 17:43:00 UTC Thu Jan 3 2013
! NVRAM config last updated at 17:43:00 UTC Thu Jan 3 2013
[ code].....
View 2 Replies
ADVERTISEMENT
Oct 21, 2011
step by step ACS 5.1's basic configuration through CLI?
View 2 Replies
View Related
Sep 30, 2011
I have an ASA running 8.2(2).I am trying to get the network on the inside interface to be able to communicate through the outside interface and on to the internet.
View 18 Replies
View Related
Sep 4, 2012
I have just bought my first non-domestic router, a CISCO 887VA-K9 which needs basic configuration to get it working. I have a copy of the configuration guide (334 pages) and CP Express user's guide (94 pages) and have spent an hour reading but either they are missing something or my brain is too small to figure out step 1. How to get started. Perhaps from where to download a CP Express installation kit for Windows.
Is the only way via a terminal emulator connected via a serial port ? Is there a graphical interface I can use ? Are there any basic tutorials for beginners ? This is probably the only non-domestic routrer I shall work on so I don't want to invest in a full training course. I just need enough to plug in the ISP credentials and set up DHCP.
View 27 Replies
View Related
Apr 19, 2011
I am trying to set up my Cisco 520 router with a firewall that will: Allow port 80 traffic to the vlan 20,Block all other incomming ports to vlan 20 (unless initalised from inside),Allow all outgoing ports on vlan 20,Block all access from vlan 20 to vlan 10 (unless initalised from vlan 10)
View 35 Replies
View Related
May 8, 2011
creating a DMZ with my current configuration. Most of my configuration has been through the ASDM as I am still learning. I'm looking for a good tutorial through the ASDM to get me on my way. What I need to accomplish is this:
I have an internal GIS server which needs to have a constant database connection to an remote GIS Server which is already configured. I've got a separate VLAN setup on my 3750 switch which connects to the DMZ configured port on my ASA with a security level of 50. My GIS server has been placed in the DMZ VLAN which is accessible from my internal clients. I have a /30 Internet block which is being used for Internet and VPN. I have a separate /28 block that I'm assuming I'll need for the DMZ to work properly.
View 1 Replies
View Related
Oct 12, 2011
I dint have any experience in Using cisco pix firewall. i got this for home lab practice.the pix can be accessed and configured by web based and CLI mode right. basic configuariton tto configure pix 515e in cli mode.
as of now im using console( hyper terminal) to access the pix. in cli based commands i need the following
1. how to assign ip address to inside ethernet and outside ethernet
2. how to enable telnet and after enabling it , can i connect my pc directly to the pix inside ethernet and do telnetting or if at all possible with (https enabled)web based config. any of these are ohk.
went at browsing to find these all i could find is web based configs. i need cli commands.
View 9 Replies
View Related
May 21, 2012
This is my 1st time trying to configure an ASA.
I'm trying to establish a very basic connection (ping) between 2 laptops, one sat on the outside interface, and one on the inside as per the diagram below:
I can ping back and forth from the ASA to 192.168.1.4, and to 10.1.1.1. However, what I'm trying to achieve is to be able to ping from 10.1.1.1 to 192.168.1.4 and vice versa.
I have attached the configuration file with this post as well.
View 4 Replies
View Related
Jan 3, 2013
I have an 871 and all I need to do is some basic rules. Here is the config I am having the issue with.
View 1 Replies
View Related
Dec 13, 2012
in lab trying to run a test upgrade of an Ace30,can seem to get it right ace30 is in slot 1 of the 6500, management vlan 10
View 4 Replies
View Related
Aug 12, 2012
I set up a basic Linksys E2500 with the following information and connected to the internet straight away without a problem: I have spent several hours simply trying to get this basic information into the Cisco 819 using CP Express without success, i.e. I get no internet. Rather than show my inputs, What is the correct setup. I am a novice so I'd rather solve this issue using CP Express just to get connected in the first instance. I have a static IP address, I connected the ethernet cable carrying the internet to the internet port of the E2500 and an ethernet cable from one of the ethernet ports of the E2500 to my PC. For the 819, I connected the internet cable to the GE WAN 0 port and the PC to one of the FE ports.
View 18 Replies
View Related
Jul 19, 2012
We currently have 7 Cisco 3524-XL switches (10-12+ yrs old) which are 10/100. We purchased a handful of Cisco 3750X switches to replace them going with the whole stackwise and redundant power supplies. Our current configuration on the old 3524 switches is that they have hardset all the ports on them to 100MB/FULL since devices would auto-neg to 100/Half. Since we're going from 10/100 to 10/100/1000 switches, I want things to auto-neg as I have heard in the past and experienced that things work better when it auto-neg to gigabit. My upper management is afraid since the old switches wouldn't auto-neg correctly that we should hard set all the ports on the new switches, which would be a nightmare since some ports would be hard set to 100/FULL others to 1000/FULL, etc.. We've tested just about all of our devices at auto with the switches and they've all auto-neg to the correct speed. In short, is Auto-Negotiation the way to go with the newer switches or is it still better practice to hard set your ports?
View 3 Replies
View Related
Apr 8, 2012
I teach in a High School and we've got about a 300 node MS Windows Network. Two MS2003 File Servers act as my DNS/WINS/DHCP servers. We have been using a WATCHGUARD FIREBOX III to act as the router/gateway between the outside external address and my internal (10.0.0.1) gateway address. All p.c's inside the network are routed to one of the Servers (10.0.0.2 or 10.0.0.4) for DNS/WINS/DHCP addressing. The servers point to 10.0.0.1 for gateway.
We are trying to replace the Watchguard Firebox with a CISCO ASA 5505 (eventually we'd like to implement VPN). When I connect the CISCO ASA, I get no internet passthrough at all.
View 1 Replies
View Related
Dec 16, 2011
I have a Cisco 2600 with IOS 12.3. I need a very basic configuration to allow traffic between two LANs. To test this I cleared the router config to the factory default state and configured my network addresses on the interfaces.
When I connected a PC to each interface I found they could ping each other, I was expecting to have to write ACLs to permit the traffic into the interfaces, thinking that the default behaviour of the router would be to deny access. default bahaviour without any ACLs or other routing configurations?
My config, such as it is, is as follows:
Current configuration : 770 bytes
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[code]....
View 5 Replies
View Related
Aug 5, 2012
I am trying to configure a Cisco 1841 to allow the users to access the internet. This is my first step with ppp. All the rest of the configuration is ok but I don't know how to setup the interfaces Dialer0 and ATM0/0/0.
Need very basic configuration that I can analyze and use on my device?
View 10 Replies
View Related
Apr 22, 2012
I am replacing a cisco linksys router with a 1941w.
I have the 0/0 accepting a DHCP from the ISP then I have 0/1 going to a switch and hosting a dhcp server.
Where I have an issue is:
A) Finding a way to turn on the wireless and make it use the same DHCP as wired and setting up a user name/wep password
B) Turning on the GUI that is supposed to be embedded on this.
C) Finding a way to make the DNS point to the default gateway so that I don't have to set the address everytime we move the box.
Here is my current configuration, and with it I can get onto the wired network and get to the internet.
Current configuration : 4712 bytes
!
! No configuration change since last restart
version 15.1
[Code]...
View 6 Replies
View Related
Nov 29, 2012
I have problem since 2 weeks. My 2 macbook pro won't connect when im in my saloon, sometimes after 2 or 3 reboot it works. When i come in the same place of the AP, i'm connected directly. When I look at the force of the signal is -35 in the chamber and -55 in the saloon.My android phone and one other old mac book doesn't have problem connecting. I look at logs and I see some max retries and some authentification failed. IT's so weird. Here is my config, did you see something wrong ?
View 3 Replies
View Related
Jan 1, 2013
First time user of cisco hardware and we just purchased the 4900m catalyst switch. My question is very general. I am simply hoping to network 3 servers together and I do not wish to do any fancy or advanced configuration. Can I simply use the web management interface for network administration and setup? I just downloaded the Catalyst 4500 Series Switch Cisco IOS software configuration guide and they talk about Cisco View network management system, is this my answer or is this what most people use for basic configuration and administration?
View 3 Replies
View Related
Jul 28, 2011
I upgraded the IOS on my 887VA router which is not yet in service. The next day I did a cold boot and made some changes. Then, when I wrote them this warning popped up which seems to imply I need to recreate my configuration from scratch in order to avoid potential issues.Is that the correct interpretation of this message/scenario? [code]
View 2 Replies
View Related
Aug 30, 2012
difference of CISCO887VA-K9 and CISCO887VA-SEC-K9.I thought it because of the Advanced Security and Advanced IP Licenses, but it isn't, I've got the -SEC- Version now just with the Advanced Security license. So I asking myself why I bought the more expensive CISCO887VA-SEC-K9 if I have to buy the additional Advanced IP Services licenses extra..
View 14 Replies
View Related
Mar 3, 2012
Have they changed the poe requirements for this router? This model seems to be a seconed gen 887 with internal wireless, fanless and instead of there being a second 2 pin power socket for the poe option there is just 1 power input with the text under is saying. 'poe option requires 5a power adapter' I have purchased the 800-IL-PM=2 to delivery poe on the first 2 ports from this document [URL]While the daughter board does fit in the stand off pegs are too short and the power adapter is incompatable.
View 9 Replies
View Related
Mar 25, 2013
Is there a GUI that can be used to setup the 887 router. I need to setup a VPN.
View 1 Replies
View Related
Apr 1, 2011
I'm trying to get an internet connection through my cisco 877va but I can't get access. I cant apply show cotroller vdsl 0 command and I can see DSL up, however, the dialer0 interface can't get access to internet. If I apply "show int dialer0 account" coomand, I get the next message: "No traffic sent or received on this interface". [code]
View 14 Replies
View Related
Feb 13, 2013
Firstly does the 887VA have a WAN port? I know it does VDSLIf this model is doesn't have both these options do you know which model does?
View 1 Replies
View Related
Dec 25, 2012
I have 2 sub net directly connected to a ASR 1002. This is the configuration
interface GigabitEthernet0/0/0
ip address 193.145.14.114 255.255.255.252
negotiation auto
[Code] ....
The interface gi0/0/0 is connected directly to 193.147.14.113/30 in another router. And the Gi0/1/1 is connected to my internal infra structure. From my router I can ping 193.145.14.113 . So. I configure my PC with default-gateway 193.147.107.3 (ASR).
From my PC
I can ping 193.147.107.3 (gi 0/1/1)
I can ping 193.145.14.114 (gi 0/0/0)
But I can not ping 193.145.14.113 (the other point connected to gi0/0/0)
Why???? It is a IP inside of a sub net directly connected to the ASR. Why the ASR is not doing routing? ip routing is enable.
View 2 Replies
View Related
Nov 27, 2011
I have a Cisco ASA5505 running the latest asdm and ios.
[I]Cisco Adaptive Security Appliance Software Version 8.4(2) Device Manager Version 6.4(5)206[/I]
I am trying to get basic web resolution and access but not having any luck. I just wanted to know if there is anything special that I needed to do with the ASA before I can do this. I've made a quick visio diagram of the network, see below: [URL]
The Vigor has a local sub net of 192.168.0.x/24 however there is also a "For routing use only" option. See below: {URL}. I'm hopeful that by configuring the "For routing use ip address" as one of my allocation of public ip's, that it should work okay. I can actually ping by IP and name from the interface of the ASA but can't do that or browse to websites from clients which have their default gateway set to 192.168.0.252. I was under the assumption web browsing should work out of the box almost as it's treated as an outgoing connection. Here is my config for you to look at: (note, I've tried to set the route outside to the local ip of the dray tek and also the "For routing usage only" IP address).
ASA Version 8.4(2)
hostname gilwoodasa
domain-name gilwood.local
enable password 9PvFytIZ2Vpy8Gon encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
[Code]...
So, if you're still reading this - all I am after is a way to get basic web browsing working. Here are the logs which show the attempted web access. [URL]
View 7 Replies
View Related
Jan 9, 2013
I need to configure a Cisco 887va router for a customer with a firewall that doesn't support PPPoA. I basically need to ensure all traffic that is recieved from the internet (ADSL connection) is NAT'd to a LAN interface so the firewall can do the specific NATing. I have the following route map and NAT rule in mind, but what I am confused about is that if the atm0 interface needs to be configured as the outside interface and vlan2 as the inside interface. How will the following work?
View 0 Replies
View Related
Nov 25, 2011
I'm trying to get an internet connection through my cisco 877va but I can't get access. I can see DSL up, however, the dialer0 interface can't get access to internet. Here is my configuration:
[code].....
View 2 Replies
View Related
Apr 23, 2013
I have a problem and I dont know much on Cisco Products
The router is Cisco 887 VA
When it starts the Leds Ok AND Fe lan are blinkng then are always on .After 10 seconds lan led is off a and pc shows cable is unplugged
I tried all ports and same thing happened .I tried with different ethernet cord but the problem persists
I installed Cisco Configuration Professional and it hangs on Retrieving Port
View 2 Replies
View Related
Feb 1, 2012
Actually I have to make a VPN between an 5520 ASA and a Cisco 887VA-K9 Router. Connected to ASA I have the outside interface, the inside-DMZ interface, the PCs interface and the VoIP interface. In the other site I will need to have a new subnet and a VoIP phone which I need to connect to the VoIP subnet in the other side in order to work with our CCM servers.I need two VPN established between ASA and 887 Router?
View 15 Replies
View Related
May 9, 2013
I have an 887VA-K9 which boots into ROMMON mode every time. It seems to have 3 tries at booting, then fails.
The entire console output from power-on is (blank lines removed):
System Bootstrap, Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 2009 by cisco Systems, Inc.
[Code].....
View 3 Replies
View Related
Apr 14, 2011
what web-based programs do i need to install a 887VA? I tried Cisco CP express version 2.1, not a supported device.
View 2 Replies
View Related
May 13, 2013
I have set up my network to pass ethernet (layer 2) traffic accross an adsl connection to another 887va router. this link is set up as a L2TP. I have a PC at one end of the tunnel and a web ranger that operates at layer 2 level. I can see the layer 2 traffic entering the router from the PC however it does not seem to go over the L2 tunnel to the other router.
I also need to know what debug codes I can enter to see if the data is being filtered and if so why?the debug L2TP gives the following output:
L2TP Tunnel and Session Information Total tunnels 1 sessions 1
LocTunID RemTunID Remote Name State Remote Address Sessn L2TP Class/
Count VPDN Group
[code]....
View 1 Replies
View Related
