Cisco WAN :: 1002 - ASR Not Doing Basic Routing
Dec 25, 2012
I have 2 sub net directly connected to a ASR 1002. This is the configuration
interface GigabitEthernet0/0/0
ip address 193.145.14.114 255.255.255.252
negotiation auto
[Code] ....
The interface gi0/0/0 is connected directly to 193.147.14.113/30 in another router. And the Gi0/1/1 is connected to my internal infra structure. From my router I can ping 193.145.14.113 . So. I configure my PC with default-gateway 193.147.107.3 (ASR).
From my PC
I can ping 193.147.107.3 (gi 0/1/1)
I can ping 193.145.14.114 (gi 0/0/0)
But I can not ping 193.145.14.113 (the other point connected to gi0/0/0)
Why???? It is a IP inside of a sub net directly connected to the ASR. Why the ASR is not doing routing? ip routing is enable.
View 2 Replies
ADVERTISEMENT
Apr 22, 2013
I need to know, can i create svi on the ASR 1002 ?
View 2 Replies
View Related
May 16, 2013
Since a upgrade in IOS XE 3.0.9, our ASR 1002 have a problem with the DHCPDISCOVER.
View 1 Replies
View Related
Mar 12, 2013
I start configuring Cisco 2821 router for multicast . First short description and attached sheme explanation. Let we say I have small network with 100 users. One router and Cisco switch 3560. Two VLAN’s, one for data another for multicast. Data from internet works fine but now I want to connect multicast servers (or source of more multicast streams) from another subnet. Router have three interfaces.I expect there should be no problems with multicast configuration, but unfortunately it is not like I expect. What I did ?
First step: enable multicast routing
Second step: on both interfaces (Fe 0/1 and Fe 0/2) - ip pim sparse-mode
Third step: configure switch that users are connected to access port in VLAN 222 (temporary to see if multicast work)
When I start VLC on computer nothing happend. If I try to connect computer on same subnet where is source of multicast streams it works fine.What I am doing wrong ? Is there anything about routing ? All subnets are directly connected. RP is not needed if I have one router or ?
View 11 Replies
View Related
Feb 4, 2013
we are replacing network equipment at one of our sites. The network will have 12, 3750X switches(6 stacks) - one stack will be the core. A 1002 will be the WAN router to the Main campus. The 1002 will connect to the core via 2 ethernet cables. I'm debating whether to use L3 or L2 between the router and Core. I've heard that routing is more efficient if L3 is used and also I will be able to create an L3 etherchannel between the 1002 and Core switch. See the attached doc.
View 6 Replies
View Related
Aug 14, 2012
i've heard that it is now possible to use Vlan 1002 -1005, perhaps only on certain devices.
View 3 Replies
View Related
Apr 2, 2013
We are having Cisco router 1002 ASR and 2841 switch. Some times perticular VLAN user will not be able to access the network but from the same switch others VLAN users can able to access. We were getting ARP entries in router but we cannot ping the IP's. Even we clear the ARP entries. Once we restart the switch users can access the network. We have changed vlan ports, uplink too. but problem not solved. and we observed CPU utilization will be going 70-80% some times and at same time switch hangs.
View 3 Replies
View Related
Sep 9, 2012
Can any share some useful links on how this works and how to configure it? Do you still need to configure FHRP or does configuring redundancy take care of active/standby relationship between the ASR's?
View 2 Replies
View Related
Feb 12, 2013
I was asked to configure a new ASR 1002 today and after successfully puttintg the config on the router (via TFTP) the router will no longer communicate with anything. There is nothing in the config to cause this (it was actually pulled off a working production ASR 1002) and I am unable to ping a local loop back IP while consoled into the router?? I removed the config, reloaded the router and configured a new loop back - same issue cannot ping the loop back or anything else connected to this router.
View 7 Replies
View Related
Feb 12, 2013
We have CISCO ASR 1002 router on our DC, I want to enable TACACS on this router.what is the usage of key, we need a separate key for every device? or. [code]
View 9 Replies
View Related
Jun 12, 2012
I know that the ASR 1002 has 4 integrated ports but the problem that I am having is that I need two of those ports to emulate a L2 switched port. Is that doable?
If not than I need to purchase the following module below. Is that price really true?
View 1 Replies
View Related
May 19, 2013
We were going to create a 2 port, layer 3 etherchannel between a 1002 router and a 3750X layer 3 core switch. We wanted to create bunled link between them but, now we are going to be putting a Riverbed device between the router and core switch. Because of this, would it be best to abandon the idea of creating a layer 3 etherchannel and just have 2 links from the router and core switch and have traffic load balance between the 2 links?The Riverbed will have 2 connections into it from the Core switch and 2 connections into it from the 1002 router. I was hoping to keep the layer 3 etherchannel but, do you think it would be best to create 2, /29 nets and have the router/Riverbed and Core Switch/Riverbed load balance.
View 5 Replies
View Related
Jul 19, 2012
We currently have 7 Cisco 3524-XL switches (10-12+ yrs old) which are 10/100. We purchased a handful of Cisco 3750X switches to replace them going with the whole stackwise and redundant power supplies. Our current configuration on the old 3524 switches is that they have hardset all the ports on them to 100MB/FULL since devices would auto-neg to 100/Half. Since we're going from 10/100 to 10/100/1000 switches, I want things to auto-neg as I have heard in the past and experienced that things work better when it auto-neg to gigabit. My upper management is afraid since the old switches wouldn't auto-neg correctly that we should hard set all the ports on the new switches, which would be a nightmare since some ports would be hard set to 100/FULL others to 1000/FULL, etc.. We've tested just about all of our devices at auto with the switches and they've all auto-neg to the correct speed. In short, is Auto-Negotiation the way to go with the newer switches or is it still better practice to hard set your ports?
View 3 Replies
View Related
Feb 9, 2012
I am trying to configure the FE8 (WAN port) to connect to the Internet. We're swtiching ISP'ssoon so this router was set up at my office and has since been deployed at the client site. So far it is just plugged in and powered, with a console cable attached but no LAN cabling since this router will replace an existing one using the same addressing (except the WAN settings of course). So for now I am just focused on working on the WAN side since I have the ISP's cable modem attached . I had intiially used CP Express to config the wan port with an IP and mask and the various port forwarding options I intend to use. Now, connected via console cable, I tried pinging the IP of the wan port, which works. Beyond that, can't ping anyting (8.8.8.8 - a Google IP), also can't resovle any DNS names which makes sense with no apparent connectivity. Likely my config is just imcomplete. Nowhere in sh run do I see a Default Gateway, yet this ISP did specify one so I assume I need to enter it. Not sure what's the right way - I get confusing results on searches telling me either to use ip default-gateway or ip default-network. I want to think that it's as simple as entering in the IP but so far I've learned with the IOS that you never do anythign without knowing all the possible implications, which I don't. Also while I am at it, I don't know what I should have for DNS entries. This router will not be a DNS server for any internal systems that function will be managed by the two Windows 2008 R2 DNS machines. The ISP has also provided two IP's for their DNS servers. I thought it would be a simple matter of just adding two entrires via ip name-server command, which I did. So now I have four entries, first the two internal servers (inaccessible currently due to no LAN cabing to this router), and the two ISP servers. Can't ping those either, but again there's no default gateway.
View 39 Replies
View Related
Sep 23, 2012
Cisco IOS 12.4 Basic check to see if the command "ip nat pool" is available?We have 12.2 basic and I know it is in the 12.4 Advanced and 15.1 Basic versions (too large of a jump in version for management). Our budget is very limited so I am hoping that 12.4 Basic has this command.
View 2 Replies
View Related
Jan 1, 2013
First time user of cisco hardware and we just purchased the 4900m catalyst switch. My question is very general. I am simply hoping to network 3 servers together and I do not wish to do any fancy or advanced configuration. Can I simply use the web management interface for network administration and setup? I just downloaded the Catalyst 4500 Series Switch Cisco IOS software configuration guide and they talk about Cisco View network management system, is this my answer or is this what most people use for basic configuration and administration?
View 3 Replies
View Related
Dec 13, 2011
attached diagram and following is the basic configuration on L3 and L2 switch. Is this configuration sufficient for simple routing?
L3SWITCH:
switch 1 priority 15
switch 2 priority 10
[Code].....
View 6 Replies
View Related
Apr 13, 2010
I' ve three 4900M switches equipped with the WS-X4920-GB-RJ45 module and the WS-X4908-10GE module. Now I'm started to setup these switches in our lab environment for the first time. They behave a little bit strange in comparison with the C3750 series which I used before and which I will replace by these powerful machines.
I tried to setup these switches to be managed through the management port. I configured IP address, default route in the management vrf, set the source-interface for tftp,ssh,ftp and tacacs to use the management port. Ping using the manangement port was successful. After finishing theses steps I configured the TACACS and AAA settings accordingly the informations I found on CCO. I tested the settings with "test aaa group authentication" command- without success. On my Cisco ACS no request was received and the switch told me he could't reach the tacacs server. Other switches in the same IP subnet are working without failure, so firewall or server should not be the problem.
View 5 Replies
View Related
Oct 8, 2011
I would like to know the technical Specification regarding the AC power supply for ASR1002.
I need to know the following:
Voltage
Amp
BTU
Watt
BTU and AMP for ASR 1002?
View 1 Replies
View Related
Jun 28, 2011
I have one ASR 1002 router and one GSR router. when i insert SFP-OC48-IR1 module with GSR and connect 100 Mb link that comming from MUX then the GSR port is up but when the link is connect with ASR with same module the port not going up.i had cross check the module GSR to ASR but the problem remain same.
View 1 Replies
View Related
Oct 27, 2012
I have Cisco router ASR 1002-F on which I have created two subinterface, Gigabitethernet 0/0/1.333 and Gigabitethernet 0/0/2.111. I try to bridge those two subinterface but no success. I can create bridg-group and everything needed but I can not add subinterface to specific bridge-group. If I try write command bridge-group on subinterface there is not even possible to chose this command.
View 1 Replies
View Related
Mar 6, 2011
OK ran into a little problem with getting this to work. Only group members participate in the encryption process, correct?
I have numerous remotes all coming into one central location. I set up a KS and have currently only 2 of the remote routers set up as GM's, with the intention of the others coming into play as I move forward. Here is basically what I have in my KS and GM's:
KS
crypto isakmp policy 10 encr aes authentication pre-share group 2crypto isakmp key testkey address [code].........
GM's
crypto isakmp policy 10 encr aes authentication pre-share group 2 lifetime [code]....
So I applied the crypto map to the serial interfaces on my routers on either side of the cloud (central-ASR1002 and remote-ISR1841). When I did this, ALL the remotes went down and I'm not sure why. Even the ones that didn't have anything to do with gdoi. Ya, it wasn't good. I thought that only the group members would be affected.
Is it the fact that my acl is encrypting any to any? Surely I don't have to reverse that and have two statements with the same syntax. I'm basically just trying to encrypt all traffic from specific remotes back to the central side. However, I'm trying to do it without taking down the rest of my network .
View 1 Replies
View Related
Oct 26, 2011
We are running LMS 3.2 with IPM 4.2 installed....and we are looking to do IPSLA monitoring on a couple of our Cisco ASR's with IOS-XE code installed.
I looked at the IPSLA feature mapping and it only talks about supported IOS code....do we need to upgrade our current IPM module to a current version?
View 0 Replies
View Related
Oct 23, 2012
I have route-map defined on my ASR 1002 12.2(33)XNE and applied to my gi0/0/1 interface. I need to change the IP address defined on the "set ip next-hop ..." line. My question is, when I make the change in just the route-map definition, does the change take effect immediately, or do I need to remove and re-apply the "ip policy route-map ..." statement on the interface? If I do have to remove and re-apply, will this be service-affecting for all the traffic flowing through the interface? I'm just not sure what to expect.
View 2 Replies
View Related
Jan 8, 2013
I have Cisco ASR 1002, code XE 3.4.1 doing site-2-site VPN with an ASA managed by another company that I have no control over running 8.3 (I think).the site-2-site vpn is very easy straight forward as follows.
View 4 Replies
View Related
Dec 6, 2011
I have a pair of physical ASR 1002 routers, called ASR-1 and ASR-2. I setup HSRP on both ASR-1 and ASR-2 on both g0/0/0 and g0/0/1 interfaces, nothing complicated, just straight forward HSRP.
Now Cisco TAC told me that HSRP is NOT supported between physical ASR routers. WTF!
Furthermore, they told me that HSRP only supported within a single ASR because of multiple routed processors. In other words, you can setup HSRP with a single physical ASR but not with two physical ASR routers.
HSRP can not supported with two physical ASR routers?
View 8 Replies
View Related
Oct 4, 2012
I am planning to implement SSL-VPN (Any Connect) on an ASR 1002 router running IOS-XE Software Version 15.1(3)S2. I need to use LDAP for user authentication, and need to understand what are RADIUS/ TACACS requirements to use LDAP. Do I need to use Cisco ACS or can I use something like Microsoft IAS or Free Radius?
View 6 Replies
View Related
Jan 10, 2011
I'm trying to upgrade the ASR 1002 we just purchased and am having some issues (this is a new device and is not in service). I first tried upgrading the ROMMON using the upgrade rom-monitor filename bootflash:asr1000-rommon.150-1r.S.pkg all command, but the upgrade didn't seem to work completely. When I do a sh platform I get the below output showing 15.0(1r)S: [code]
no valid BOOT image foundFinal autoboot attempt from default boot device...Rommon upgrade requestedMaximum upgrade attempts exceeded, continuing with old Rommon...
I've also tried upgrading the IOS, but that is not working either. I tried "boot system flash:asr1000rp1-advipservicesk9.03.02.00.S.151-1.S.bin" command, but that did not work. I made sure the image was good using the "verify" command and made sure to set "config-register 0x2102". After I do a wr me and reload the router I get the below errors. [code]
View 1 Replies
View Related
Sep 30, 2012
how can I monitor and prioritise traffic on a ASR 1002? Currently we have allowed another organization to use our 1GB link and we would like to monitor what sort of traffic flows through it and want to prioritise the traffic depending on the applications.
View 1 Replies
View Related
Dec 21, 2010
As soon as I connected my ASR 1002s to the Internet and digested the Internet BGP table, I began receiving this message. I’ve google’d and turned up nothing so far. I assume I need to allocate more memory to this process.
%PLATFORM-4-ELEMENT_WARNING: R0/0: smand: ESP/0: Committed Memory value 312% exceeds warning level 310%
Here's a sh mem:
#sh mem Head Total(b) Used(b) Free(b) Lowest(b) Largest(b)Processor 3008A008 1758530508 647878488 1110652020 1110104020 1109994164lsmpi_io 98FEB1D0 6295088 6294120 968 968 968
View 1 Replies
View Related
Nov 23, 2011
I've been working with a company in the UK to get a PTP connection setup between Minneapolis, MN and Chicago, IL. At each site with have a ASR1002. The connection is made via a fiber connection from Level 3. Level 3 is just handling layer 2 and we are to take care of everything else. As of right now they can see the mac address of the Minneapolis port in the Chicago router. But, I can't see theirs. Nor can I ping the Chicago router. The config that was give to me by the higher engineers is simple enough.
View 3 Replies
View Related
Sep 13, 2012
I am working up a configuration template for an install I am doing in a couple weeks and wanted to take a look at the base config of an ASR1002.
View 1 Replies
View Related
May 12, 2013
I have a cisco ASR 1002 I have plugged a host into an addressed port and the port comes up however the host cannot ping the router and the router cannot ping the host. Neither can router ping its self. I do the same on a cisco 2800 router and it works fine. What's goin on. Is it the fact that this is a ASR router ?
View 5 Replies
View Related
