Cisco Wireless :: Configuration Of 887VA-W Access Point
Nov 29, 2012
I have problem since 2 weeks. My 2 macbook pro won't connect when im in my saloon, sometimes after 2 or 3 reboot it works. When i come in the same place of the AP, i'm connected directly. When I look at the force of the signal is -35 in the chamber and -55 in the saloon.My android phone and one other old mac book doesn't have problem connecting. I look at logs and I see some max retries and some authentification failed. IT's so weird. Here is my config, did you see something wrong ?
I have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
just i have purchased new cisco air-ap1142n-a-k9 wireless access point, trying to configure the wpa2 configuration for security reason, but unable to configure in any security mode. So currently my AP is working no security / encryption mode.
I have two 1262N access points with 5Ghz antennas, and I have configured one of them as a root bridge and the other as a non-root bridge; both using the same ssid. I have enble both dott11Radio interfaces on each access point. The problem I am having is that they do not associate. I have not configured them for any encryption or security. I just want to make sure the connect before I add any other configuration. Is there anything else that I need to configure to make them associate.
I have a wap200 wireless access point configured and connected to the switch 2690 switch on vlan1, when I connect the wireless access points to the switch the port become disabled.
I have a cable broadband installed in my home i just bought cisco 1200 series access point...now how to configure my access point. I believe I have to plugged fastethernet cable coming out of my cable modem to access point after that? What I have to do ....do I have to configure the cable modem as wlel or not???
I have 50 WAP connected to a WLC 5508. When I backup the config I don't see the custom settings I put in some WAP. Where are the WAP settings saved at ?
how to configure an AIR-LAP521-G-E-K9 wireless access point in standalone mode? I've tried connecting it to a standard 1GB switch, feed it with IP address via DHCP it responds to PING but when it comes to detect it in CCA (3.1) it says unable to connect without even asking for username and/or password. Trying to connect to it through HTTP or HTTPS doesn't work either.
I must configure an Aironet 2602e Access Point, as a standalone access point (without WLC), but I can not find Configuration Guides for that. I have only found the "getting started guide" but there is described an installation combined with a WLC, which I have not. Is it provided no real guidance from Cisco? I did something never done before.
I am struggling to get this working after spending many hours looking at it I am now completely stuck. We are upgrading from a 857W to this 887 VA-M I have some experience of IOS and the 800 series. Our 857W works perfectly using almost the same config. Our situation is that the router will sit in front of our firewall and act essentially as a simple router passing everything through to our Firewall. Nat is done at the Firewall.
We currently have the following configuration that seems to connect the the ISP fine but I cannot connect to the vlan2 port on the switch the firewall cannot connect to he internet or route anything via the Vlan2 port no pings etc.. I am using Fast Ethernet 0 as the Vlan2 port and the rest are V LAN 1 with a local network address to allow me to connect a laptop.
We have a block of static IP addresses, the base of which is assigned to the V LAN 2 interface and used by Dialer 0 as IP Unnumbered. Config below.
4590 out of 262136 bytes ! Last configuration change at 17:42:06 UTC Thu Jan 3 2013 ! NVRAM config last updated at 17:43:00 UTC Thu Jan 3 2013 ! NVRAM config last updated at 17:43:00 UTC Thu Jan 3 2013 [ code].....
I have two Cisco AP 1242G and i'm trying to configurate a Point-to-Point Bridge Configuration to connect two wired LAN. Figure 1.8 [URL] I would connect two wired networks.
I tryed two configurations: Root and Non-Root AP. This way every wired PC on the Root AP can connect to the Access points, but cannot connect to the wired PC on the Non-Root AP.AP and WGB. Even this way the wired computers on one AP cannot connect to the wired PC on the WGB. This way only the wireless client can connect to the wired network. This is my network:
Root Bridge Non Root Bridge 10.0.0.1 10.0.0.2 Wired clients on the RB Wired clients on the Non RB 10.0.0.100 10.0.0.200
How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
I upgraded the IOS on my 887VA router which is not yet in service. The next day I did a cold boot and made some changes. Then, when I wrote them this warning popped up which seems to imply I need to recreate my configuration from scratch in order to avoid potential issues.Is that the correct interpretation of this message/scenario? [code]
My question is regarding gaining access to my Linksys wireless router configuration page. I recently turned my Linksys WRT54GL wireless router into an access point and since I have done so I am no longer able to access the configuration page for my router.
The problem that I am encountering is not one of connectivity, but rather entry. Prior to turning my wireless router into an access point I was able to connect to the router by means of my browser (192.168.1.1). I am still able to connect to the router, but whenever I type in a user name and password the router just simply does not recognize the information. I have tried resetting the router multiple times, but I am still denied access to my router despite having the correct user name and password. I have version 1.1 of the Linksys WRT54GL wireless router and have the latest firmware.
I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
I have problems with a vpn configuration for point to point ipsec tunnel.Communication stops randomly, I have the ability to view any record or log of court?
difference of CISCO887VA-K9 and CISCO887VA-SEC-K9.I thought it because of the Advanced Security and Advanced IP Licenses, but it isn't, I've got the -SEC- Version now just with the Advanced Security license. So I asking myself why I bought the more expensive CISCO887VA-SEC-K9 if I have to buy the additional Advanced IP Services licenses extra..
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
Have a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine! The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
