how to configure an AIR-LAP521-G-E-K9 wireless access point in standalone mode? I've tried connecting it to a standard 1GB switch, feed it with IP address via DHCP it responds to PING but when it comes to detect it in CCA (3.1) it says unable to connect without even asking for username and/or password. Trying to connect to it through HTTP or HTTPS doesn't work either.
View 4 RepliesI must configure an Aironet 2602e Access Point, as a standalone access point (without WLC), but I can not find Configuration Guides for that. I have only found the "getting started guide" but there is described an installation combined with a WLC, which I have not. Is it provided no real guidance from Cisco? I did something never done before.
View 2 Replies View RelatedWe have this access point AIR-AP1231G-A-K9 for mobile users. current version is c1200-k9w7-mx.123-7.JA4. Sometimes users are able to associate but not getting IP address from dhcp. It shows 0.0.0.0 for the particular client.
View 2 Replies View RelatedCan I convert a standalone 1600 access point to a CAPWAP based AP when I choose to deploy a WLC later?Cant see any literature on cisco.com that is specific to the 1600 APs
View 1 Replies View RelatedI have to set up the AP in a standalone mode to support voice and data traffic through the wireless network. for this, i was trying to look for the config guide so i know how to go about it, but all the doc was refering to controller based setup. i followed this link URL
I have never worked on wireless in a standalone mode, so this is the first time i will be doing it.
I can run the Cisco AIR-LAP1142n-a-k9 access point in standalone mode? I don't want it to look for a controller when it boots up.
View 3 Replies View RelatedI have two 5504 Controller. Original Liceses 100 per Controller. At the beginning the Controllers were running standalone as a Primary and secondary in a Mobility domain. Now they are running in a HA Pairing mode. One Controller as the Primary an the second as the Standby in the redundancy HA SKU mode. The first step SSO disable is done.
how setup back the HA SKU Standby-Controller to get again the 100 licenses?
We have a customer who is evaluating a Cisco Vs. Motorla wirless solution. He says that a Motorola AP can only work in standalone mode for 48 hrs. after it lost communication to the controller. Is there any limitation like this with a 2500 controller and 1140 series access points solution?. Is there any reference to show?
View 3 Replies View RelatedEa4500 as a wireless access point only mode
View 1 Replies View RelatedWe have 4 access points in my network i want configure 1 is ap mode another 3 is bridge mode Is it possible to configure in 4410 N ? if i configure bridge mode can i use single SSID&Securtiy key for all aps. how to i use these 4 access points
View 1 Replies View RelatedI have a AIR-SAP-1602i-k9 Aironet. I cannot find any information on the Cisco site on how to configure the Aironet without a controller. I assumed a standalone meant I could just login.
I tried seeing if it would pull a DHCP address on my network but it didnt.
I recently purchased the E3000.I thought i had read that this devices can act as an access point. There is no clear "access point" mode option so i configured it as best as i could to work with our radius server. I can connect to the wireless with radius credentials just fine but i don't get assigned a ip address from dhcp. I tried using an old blekin that does have ap mode and it works just fine.
View 1 Replies View RelatedI have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
View 1 Replies View RelatedI have spent most of the weekend trying to get this router to act as a proper Access Point.
When it does work (Stay connected) speeds and latency are rotten. If I go back to Routing Mode this thing kicks butt, but I isolate all devices attached to a different subnet and trying to set up proper routes has proved imposable. Firmware 1.0.2 r 13
The online help stated to connect to the "internet interface" when in Bridge Mode DHCP Server Is not broadcasting to on the wireless or wired interfaces.
If I used the wired interface as the uplink I can broadcast the DHCP to any device on wired but again nothing to the Wireless. When I "Show Routing Table" I see two static routes pointing to the ATT router for the Wired/Wireless Interfaces.. 0.0.0.0 255.255.255.0 (my Gateway) Wired/Wireless (my Gateway) 255.255.255.0 0.0.0. Wired/Wireless
AP mode should only be working in Broadcast. By connecting the Wired Interfaces alone up to my switched network should not use the router at all. If you force all traffic to my router all traffic has to be inspected by the firewall You create a bottleneck my router interface is 10/100.
ATT 2 Wire Gateway/Router with pinholes. 10/100/1000 Non managed 24 port Switch Network. Server infrastructure serving DNS/DHCP.
I decided to buy this after reading it offered Bridge/Access Point mode instead of getting the WAP610 because I wanted to have the option to change to routing mode or AP mode. Since my ATT Uverse Router Wireless is “g” it takes forever to transfer files to and from my servers.
I have a network with 2 WRT54Gs in it. One in the besement connects to my cable modem and serves as a gateway and DHCP server as well as a wireless access point. That WRT54G is perfectly accessible. I have another in my room set up as a router and access point only, connected by its ethernet port to the gateway. This one proves a bit trickier. Thet network works flawlessly, and if I couldn't see it sitting right there I would doubt it even existed. I can't ping it (I forgot the IP but tried all the ones that seemed logical), it doesn't show up in my network map, etc. From what I gather that's how a switch is supposed to work. But since this is also a managed router, I would think there should still be some way to connect to it to administer it. How can I log in to this router to change settings if I need to?
I'm not sure if maybe 192.168.2.0 is the other router or if that's some kind of special address (My network is on the 192.168.2.* subnet, don't even ask why...). I've seen it in other posts about routing tables but they all had it routing to 0.0.0.0 instead of the router's own IP. I tried pinging 192.168.2.255 and got no responses at all, not from any computers or from either of the routers, so that was not useful. Tracert from my computer to the gateway doesn't show the router (my computer connects to the gateway through the router).
I have just installed 3 access points along with 6 repeater access points all running V12.4. They are all AIR-AP1242AG-E-K9 using the 2.4GHz radio.
Prior to installation I bench tested that the repeaters would associate with the access points and if one of the access points was turned off the repeaters would automatically roam to another access point. I did not have all 9 devices powered up at the same time, but did have 2 repeaters and 2 access points powered up to simulate association and roaming.
During installation as access points and repeaters were powered up everything behaved as expected (repeaters were associating to access points etc.) however during installation once everything was installed the 3 access points were all powered down for half an hour or so and once powered back on the repeaters did not automatically re-associate until they were re-booted.
I have now configured the repaters with parent MAC addresses to reflect the above current assocaition pattern but not yet powered off the access points to test if this forces re-association as this is now a live operational site!!
Is it normal to have to re-boot the repeaters if ALL 3 access points are powered down at the same time? i.e. If only one access point is powered down will the repeaters automaically roam to another access point o.k.?
I have around six number of Cisco 1252 Access Points on HReap mode and wIPS submode in one particular location. This was implemented more than six months and it was working fine. Suddenly, I faced Network conjestion and more bandwidth utilization in that location in particular. But, after disabling the wIPS in the AP, The bandwidth got stable and working fine. Not sure, if wIPS will utilize more bandwidth..
Does this will be anywhere related to the RF Heat maps that Cisco NCS will generate? As there is no map uploaded for that location, Will this cause an issue?
I have one controller 2504 and some 1200 series access points.I am using 3 SSID .I want to use two ssid in HREAP mode but HREAP mode is not showinh in access point because multicast is enabled on AP mode. see the below picture
I have disabled the multicast globally from CLI. config network multicast global disabled
disabling the multicast so that i can set the access point in HREAP mode.
I have a Cisco 880 (supplied by my company and as such I have little access to the control panel). I have a Linksys (Cisco) E1200 to use as an access point. Cisco setup (love it!) but the simple setup gives the E1200 an ip range starting at 192.168.1.1 while the Cisco 880 range is 192.168.185.113. I need to have all connections in the same ip rage (192.168.185.xxx) for remote monitoring. What is the best way to accomplish this? Bridge mode (I don't need Guest Mode which I read is not possible in bridge mode)? Disable DHCP on the E1200?
View 1 Replies View RelatedBought wap200. I can't adjust the wireless repeater mode. Linksys x3000 supports wap200? What settings need to be made?
View 4 Replies View RelatedMy access point 1042 series in light weight mode reloads itselft every time it booting, sometimes it boot succesfully.
View 2 Replies View Relatedwe have a couple of AP1262N-E-K9 access point with firmware version 12.4(25d)JA1 operating in autonmous mode.
I attempted to measure the signal quality between the APs by setting one device to repeater mode while all others are in root mode. Then, I execute the following command: dot11 Dot11Radio 0 antenna-alignment
1. The output of "show dot11 antenna-alignment" is incorrect, the % value represents the signal strength in dBm without the - (minus). E.g. "-25 dBm" is displayed as "Signal 25% 0 dBm".Now, I know that is only a display error but still this is not clean. Is this a known issue?
2. Why are the measured signal strength values not displayed on the SSH console during the antenna-alignment test? Is it obligatory to use the console to see these values? Or is it also a known bug which might be fixed in later firmware versions?
How do I connect to the EA6500 once it's in Bridge mode acting as a wireless access point? Checked the posts and some seem to be able to do this but, we cannot.
View 6 Replies View RelatedI have problem since 2 weeks. My 2 macbook pro won't connect when im in my saloon, sometimes after 2 or 3 reboot it works. When i come in the same place of the AP, i'm connected directly. When I look at the force of the signal is -35 in the chamber and -55 in the saloon.My android phone and one other old mac book doesn't have problem connecting. I look at logs and I see some max retries and some authentification failed. IT's so weird. Here is my config, did you see something wrong ?
View 3 Replies View RelatedSetup N600 DB as an access point using the most recent firmware,3.03.12? Once I do I'm not able to access the dashboard even through I enabled the remote management option.
View 2 Replies View RelatedI have an n600 ( F9K1102 v1 , firmware 1.00.09 ). My ISP provides my main router for my network, but I want to use the N600 as an access point, I have activated the "Use as Access Point" feature.Is it possible to still utilize the Guest Access feature in this case?
View 1 Replies View Relatedjust i have purchased new cisco air-ap1142n-a-k9 wireless access point, trying to configure the wpa2 configuration for security reason, but unable to configure in any security mode. So currently my AP is working no security / encryption mode.
View 16 Replies View RelatedI have two 1262N access points with 5Ghz antennas, and I have configured one of them as a root bridge and the other as a non-root bridge; both using the same ssid. I have enble both dott11Radio interfaces on each access point. The problem I am having is that they do not associate. I have not configured them for any encryption or security. I just want to make sure the connect before I add any other configuration. Is there anything else that I need to configure to make them associate.
View 1 Replies View RelatedI have a wap200 wireless access point configured and connected to the switch 2690 switch on vlan1, when I connect the wireless access points to the switch the port become disabled.
View 1 Replies View RelatedI have a cable broadband installed in my home i just bought cisco 1200 series access point...now how to configure my access point. I believe I have to plugged fastethernet cable coming out of my cable modem to access point after that? What I have to do ....do I have to configure the cable modem as wlel or not???
View 2 Replies View RelatedI have 50 WAP connected to a WLC 5508. When I backup the config I don't see the custom settings I put in some WAP. Where are the WAP settings saved at ?
View 17 Replies View Relatedhow is the 1130 point-to-point bridge work in lighteight mode ?
Is this supported on 5508 and on new 2500 series controllers?
How does the WCS manage the point-to-point link?
I am aware that there is Lightweight software for the 1300 series bridges but never used one so far
I have a stack of 8 3750x switches connected via Stackwise. In addition, I have these switches configured as two Powerstacks. When I look at the Powerstacks, they are showing as being in power-sharing mode. When I look at the individual switches, they show as standalone. Right now, I have 1 switch in each powerstack that has two power supplies, and then the other three have a single power supply. Below is the output for "Show stack-power detail" as well as the Powerstack configurations.
Power Stack Stack Stack Total Rsvd Alloc Unused Num NumName Mode Topolgy Pwr(W) Pwr(W) Pwr(W) Pwr(W) SW PS-------------------- ------ ------- ------ ------ ------ ------ --- ---Powerstack_1 SP-PS Ring 2145 45 570 1530 3 3Powerstack_2 SP-PS Ring 2860 60 760 2040 4 4Powerstack_1-1 SP-PS Stndaln 1430 520 190 720 1 2
Power stack name: Powerstack_1 Stack mode: Power sharing Stack topology: Ring Switch 4: Power budget: 700 Power allocated: 190 Low port priority value: 20 High port
[code].....